Used pellet mills for sale (33)

Condition: used, Year of construction: 1994, operating hours: 392 h, functionality: limited functionality, machine/vehicle number: 1115, type of input current: three-phase, total height: 150 mm, total length: 2,200 mm, total width: 900 mm, overall weight: 1,800 kg, power: 11 kW (14.96 HP), input voltage: 380 V, Equipment: documentation/manual, Brand: Pawert Djdjzyau Eepfx Aa Hocl Type: I-40/85 Year of construction: 1994 Capacity: 150 kg/hour Briquette dimensions: Ø 40 mm Motor: 11 kW Weight: 1800 Including feed screw and discharge chute.

Condition: used, SPE Renergi Low Temperature Dryer. The Renergi Dryer is used for drying of sawdust and other materials for production of biofuels. Dsdpfx Aszvq Rcja Hjcl The dryer can dry sawdust, bark or wood chips from a humidity level of about 50% to a level of approximately 10 %. This low-temperature dryer utilizes warm (or hot) water from a recommended temperature of 65°C and higher. Maximum water temperature - 110°C. Power supply safety: The dryer must only be fed by 3x400 V AC (630 A) 50/60 Hz with a separate Protective Ground conductur. Power supply Data: • Voltage 400 V AC, three phase • Recommended fuses in supply line: maximum 3x630 A • Typical power consumption: 200kW The dimension of the Dryer are roughly 17,4 by 5,7 meters, with a height of 10,7 meters. The floor space required is approximately 21,4 by 8,0 meters. A ceiling height of at least 15 meters (or 4 meters above the top of the media inlet). Air supply: at least 24 kg gas/s fresh air is required for the operation of this machine. This corresponds to 20nm3/s, or 72 000 nm3/h. Airflow: max 200 liter/min Air pressure: min 4,5 bar, recommended 6,0-8,0 bar Water supply: hot water supply, with a flow of 32 dm3/s. Water pressure: min 1.5 bar, max 6.0 bar Operating temperature range: • Incoming air temperature: -20°C to 50°C • Relative humidity: 0% to 60% Raw material/media: • Relative humidity: 45% to 55% by wieght • Requested relative humidity: 8% to 15% in the dried material Capacity: • The dual-cell, 4 m wide dryer can typically handle 2400 kg of material with a moisture content of 55% by weight in each load • The dryer is capable of drying 6000 kg raw material, with a water content of 55% to 10% in approximately one hour. SRE’s dryer is desinged in accordance with European directives. The equipment is designed to conform to the essential requirements of: • The Machinery Directive 2006/42/EC • LVD 2006/95/EC • EMC 2004/108/EC The dryer is located in Straupe parish, Cēsis district, LV-4152, Latvia. Available for viewing on working days, 08:00 to 17:00, by prior agreement on the viewing time. The dryer is already dismantled All electrical schematics, manual, operating instructions available Upon request, we can provide a contact person with this type of working dryer for consultation Price: 35 000 EUR (VAT is not included)

Condition: refurbished (used), Year of construction: 2012, operating hours: 1,000 h, functionality: fully functional, overall weight: 100,000 kg, Pellet production line of Italian manufacture. Renown brands of machinery like General Dies SRL, Miller SRL, FIDA SRL and other brands. Capacity of the line 1.3 tons per hour Djdpfx Aaei Akrkj Hscl Pellet press General Dies TAU4 – 110kw Container with movable floor and hydraulic power aggregate Triple-Pass rotary drum dryer 2.5 tons catalog capacity (effective capacity up to 1.5 tons/hour) Transport divider for biomass separation Pezzolato PTH 660/700 (Wood chipper, possibly excepted from the line if buyer wishes so) Furnace for rotary drum dryer and complementary equipment Hammer mill “Miller SRL” 75 kw Transport conveyors for biomass transport Cyclon for dust removal Cooler silo for dust removal Weighing and packing equipment Electric cabinets for the entire line with cables Ventilation tubes for sawdust and wood chips transport Screw air compressor 860l Pump for grease dozing in central press lubrication system Included are additional pieces of equipment like filter silo bags, metal connections etc. (complete line is between 4 and 5 full trucks of equipment)

Condition: used, functionality: fully functional, Performance for 6 mm diameter pellets 2.5-3 t/h Dcodpfx Asx S Ibgsa Hol We used it for about 5 years. It was purchased used but in very good condition. All bearings were replaced 1 year ago. It was working very well before it was disassembled. A new die with rollers has been manufactured for it and is available for an additional price. For additional information, please write on Whatsapp.

Condition: like new (used), Year of construction: 2024, Pellet production plant – complete line – fully automated Salmatec press Rematec hammer mill Belt dryer Dodjzg Eudepfx Aa Hscl VAI bagging machine Cooler Sifter Palletizer Less than 1000 operating hours – certified Option for on-site reinstallation Option for on-site operator training

Condition: used, Year of construction: 1985, functionality: fully functional, For sale: granulator from the renowned manufacturer Buhler. Granulator model: DPAA-660 Motor power: 160 kW – option to install a more powerful motor – 200 kW. Die diameter: 660 mm, Die working width: 160 mm, Granulator output on straw / sawdust: 2 – 2.5 t/h The granulator is currently dismantled. For a committed buyer, we will assemble it using new wear parts. Contact for more photos and details. Dedpfew Uh Nzex Aa Hscl Machine available for inspection in Sępólnie Krajeńskie, Kuyavian-Pomeranian Voivodeship, Poland.

Condition: used, Complete pellet production line with a maximum capacity of up to 5 tons per hour (limited by dryer capacity). Pellet Presses (3 units): CPM 7122 CPM 7922-2 CPM 7930-4 (only ~200 working hours) Hammer Mills (3 units): Maier hammer mill for wet material Maier hammer mill for dry material Kamas hammer mill (for burner material production) Cooling System: CPM pellet cooler Additional Information: Electrical and control systems are fully integrated into container units Production line has been in operation for approximately 2 years Belt conveyor, reception hopper 4 kW Dryer: distributor reception hopper 2,2 kW Conveyor belt, reception hopper 2,2 kW Worm conveyor for drum dryer 2,2 kW Drum dryer 7,5 kW Main cyclone 90 kW Sluice head cyclone 7,5 kW Fan cyclone 18,5 kW 1 Sluice cyclone 1 2,2 kW Sluice cyclone 2 0,55 kW Sluice cyclone 3 0,55 kW Worm conveyor for cyclones 1-3 3 kW Hammer mill – Maier 160 kW Hammar mill for dust burner – Kamas 110 kW Hammar mill for woodchips – Maier 132 kW Worm screw for elevator 4 kW Elevator for buffer pocket 7,5 kW Buffer pocket high/low 8/4,5 kW Scraper conveyor for the presses 2,2 kW Worm screw for dust mill 2,2 kW Press 1 CPM: Model: 7122 Main engine 160 kW Cascade mixer 7,5 kW Feeding screw 2,2 kW Oil lubrication 1,5 kW Grease lubrication 0,18 kW Press 2 CPM: Model: 7922-2 Main engine 250 kW 200 kW Cascade mixer 7,5 kW Feeding screw, frequency converted 2,2 kW Oil lubrication 1,5 kW Feeding screw 4 kW Press 3 CPM: Model: 7930-4 Work only 200 hours Main engine 250 kW Dedsyvz Afspfx Aa Hocl Cascade mixer 7,5 kW Feeding screw 2,2 kW Oil lubrication 1,5 kW Oil cooler 2,2 kW Grease lubrication 0,18 kW Conveyor for warm pellets 2,2 kW Belt conveyor to the refrigerator 2,2 kW Pellet refrigerator, outflow 1,5 kW Fan for the pellet refrigerator 11 kW Fan for the suction 5,5 kW Elevator 2,2 kW Belt conveyor 1,5 kW Belt conveyor 4 kW Combustion air fan 45 kW Conveyor fan 22 kW Conveyor fan 11 kW Silo filter 0,04 kW Filter fan 4 kW Screw for dust silo 2,2 kW Driving motor for dust silo 1,1 kW Oil pump 1,5 kW Dosing screw 0,75 kW Sluice feeder 0,37 kW

Condition: excellent (used), Year of construction: 2008, functionality: fully functional, power: 75 kW (101.97 HP), For sale: fully operational pellet production line. Dodpfjw Ry U Iex Aa Hocl

Condition: ready for operation (used), Year of construction: 2024, operating hours: 21 h, functionality: fully functional, total height: 60,000 mm, input current: 250 A, compressed air connection: 6.2 bar, input voltage: 380 V, warranty duration: 24 months, Equipment: documentation/manual, 1. Material feeding table with moving chain mechanism. Adjustable height min 0.8, max 1.4 and electric drive. 3kw L 4m 2. Large roller shredder with double blades, diameter 1.8m, depth 1.9m 380V 30kw 3. Connection point with a lock for feeding bulk materials to the crushing mill. 4. Hammer mill turbine 380v 35kw 5. Mixer for crushed raw materials, with adjustable feed hatch. Volume 4.8m3 380V 2.2kw 6. Large horizontal granulator with automatic lubrication system and programmable rotor automatic lubrication. Additional cooling of the granulator rings and fine dust extraction. MAX capacity 3T/H 380 90kw 7. Small moving conveyor belt Width 38cm, Length 2m 380v 0.5kw Dodew U Ugmjpfx Aa Hocl 8. Large transport belt with head valve Width 38cm Length 6m 380v 1.5kw 9. Pellet cooler with cyclone for fine dust collection and head valve MAX capacity 3.5T/H 380V 3kw 10. Screener/vibrating table with screenings collector and screw feeder. 380V 1.5KW 11. Long screener cylinder with screening mesh Length 3m 380V 1,5kw 12. Conveyor belt with feed to packaging. Length 4.2m 380V 0.75kw 13. BIG BAG packaging unit with calibrated scales, tolerance +/- 5gr per 1T 14. Screw conveyor for feeding material to the automatic packaging machine in bags. Length 5m diameter 27.5cm 380V 3kw 15 Automatic packaging machine with bag sewing and PVC bag sealing. There is also an automatic labeling conveyor table. Max capacity 4.2T/H with air compressor. 16. New semi Electric 3T pallet trolley

Condition: new, Year of construction: 2023, We offer this new pellet press with a packaging line, manufactured in 2023. Manufacturer: Artmash (Ukraine) Dcedpfxszh Hd Nj Aa Hol Year of manufacture: 2023 Production capacity: 700-900 kg/hour Die: 6 mm Condition: new (10 tons produced for testing) Category ID: 917 Type ID: 2701 Type: pellet press with packaging line If you have any questions or require additional information, please send us a message or call us.

Condition: used, Granulation and packaging line. Model: HM700E PRO 11KW Year of manufacture: 2022 It includes: Hammer mill - shredder Chip mixer Chip feeder Granulator Vibrating table Product feed belt (conveyor belt) Pellet hopper with packaging equipment Bag sealer and chip moisture meter Hammer mill with cyclone Motor: 11 kW / 400 V Productivity: 300 - 700 kg / h Weight: 360 kg Soft start installed Cutting system 16 hammers Chip mixer: Volume: 1.0 m³ Chip feeder: Motor: 3.3 kW / 380V Feeds up to 800kg / h Granulator: Motor: 22 kW / 380V/50hz; Productivity: 300 - 700 kg/h Weight: 590kg Soft start installed Vibrating table: Djdpfx Aoxcy D Esa Hscl Weight 90kg Product feed belt (conveyor belt): Dimensions: 5m × 0.4m. Automated packaging equipment: Dimensions: 1, 90x2, 50x2, 30 Volume: 1.5m³ Packing in bags: 1 - 50kg Equipped with two types of scales Bag sealer 220V Moisture meter

Condition: used, Münch RMP 660 pellet press for the production of wood pellets and biomass pellets from sawdust, wood shavings and other organic waste materials. The machine is suitable for industrial pellet production, offering high pressing capacity and consistent pellet quality. Ideal for wood processors, sawmills and biomass plants. Technical data: - Screen: 6 mm - Motor: 2 x 90 kW - Inner diameter of die: approx. 660 mm - Number of press rollers: 2 - Pressing capacity: up to approx. 3–5 t/h Dedjzryyrepfx Aa Hscl

Condition: excellent (used), Year of construction: 2015, COMPLETE PELLET PRODUCTION LINE 6 t/h Hydraulic walking floors - double for hard and soft wood Conveyor belt 12m with magnetic separator for chips Two hammer mills each 130 kW for wet material Two beams with hydraulic floor befor drum dryer Dryer for drums of 12 m FIEDLER boiler 3.5 MW Dedpfxoqy Hcds Aa Hecl Refiner 250kW with transport fan and filter Silos bin ZEPI for dry material Z conveyor ZEPI above three silo bins for pellet mill 0qe0k TRI Pellet Mill ZEPI ZPM600 with 200kW (2pcs) and 160Kw Pellet mill production year 2015 (two pcs) Conveyor belt 10m for hot ball, conditioner and aspirin system vibro sieve ESSEGI packaging system (ITA) 2019 Pallet system ROBOTIK KOGLER (SLO) 2015 Grecon spark detection system Electrical cabinet room for complete equipment Line in operation, capacity 6-7 t/h

Condition: used, Ražotājs: Munch Modelis: 420 Ražîba: 1 tonna stundā Elektrojauda: 2x75 kW Diametrs 420 mm Komplektā ar dzesētāju pēc kapitālā remonta clear 134 / 5,000 Translation results Translation result Manufacturer: Munch Model: 420 Production: 1 ton per hour Electric power: 2x75 kW Dodpfx Aaewfqn Ae Hocl Diameter 420 mm Complete with cooler after overhaul

Condition: good (used), Year of construction: 2007, functionality: fully functional, Pellet production line based on Italian producer Zepi pellet press, hammer mill, pellet cooler and sifter. Dcjdjvx S Ryopfx Aa Hsl Machines are really powerful and reliable. Some parts like hammer mill are completely refurbished. Year of production 2007.

Condition: reconditioned (used), Year of construction: 2008, functionality: fully functional, Fully refurbished pellet press from Italian manufacturer ZEPI. The main engine power is 315kW, which allows the production of up to 6t/h of wood pellets. The delivery set also includes a ZEPI ZC500 paddle mixer and a ZEPI ZFS250 feed unit. Dsdpfx Ajvpvp Isa Hocl

Condition: good (used), Year of construction: 2014, Pellet Press Dcsdpfx Aasvdrtxs Hjl Manufacturer - TEKNO UNO Model - TK 304 Year - 2014 Motor Power - 50 kw Capacity - 450 kg/h

Condition: used, Year of construction: 1988, height adjustment type: hydraulic, 1x Used KAHL C39 - 1000 Pellet Press Pelletmill Incl. Hydraulic nut Incl. 4 Roller head Incl. 5 Roller head Dcsdpfov N Rdasx Aa Hel Incl. various spare parts Incl. chassis 110kW 1500rpm Electric motor

Condition: used, Pellet press Dodjy E Rrbjpfx Aa Hecl Manufacturer: CPM Model: 7930-4 Year: 2019 Complete with feed mixers

Condition: good (used), Year of construction: 2025, Requirements: - Material must be free-flowing (less than 18 mm) - Material must be pure, ash content less than 1% ATRO Pay attention to: sand, stones, and minerals - It is compressed using press tongs - Material must be dry, maximum 15% ATRO New: Innovative combination of briquette and pellet Options at an extra charge: Plant construction / mütek system technology: - mütek Shredder MRZ shredding technology - Conveyor belts - Overband magnets - Dust extraction systems, optionally with rotary airlock - Transport screws - Silos - Control system linkages of all kinds - Semi-automatic packaging technology + 24-hour operation possible + Compact design + High energy efficiency thanks to innovative hydraulics + Briquette density of up to ≥ 1 kg/l possible *Details after testing Mode of operation: The machine has a silo with a stirrer. In each of the 4 corners of the storage silo, there is a vertical screw that compresses the material downwards into the pressing chamber. The machine operates with two cylinders, each of which compresses in two directions (either while the cylinder moves forward or backward). This results in 4 briquette outlets, each with 6 individual briquettes. *ideal for the automatic feeding of the heating boiler Format: Ø 30 mm Throughput capacity: up to a maximum of 250 kg/h Motor power: approx. 27 kW (in total) Dimensions: 3.1 x 2.3 x 2.2 m Weight: 3.55 tons Your advantages: Compact briquette/pellet format enables firing of industrial furnaces using screw feed Fully automatic 24-hour operation possible High energy efficiency Briquettes/pellets with consistently high quality & density Dcsdpfjfbb Arsx Aa Hel For automatic feeding into industrial furnaces Small to medium quantities of wood chips, which are produced in the processing industry of various materials (especially wood, biomass, etc.), can be optimally compressed. The small Ø 30mm format represents an attractive alternative. In contrast to our conventional briquettes, these can be automatically fed into industrial furnaces. In addition to wood, various other materials can also be easily processed (various biomass and agar-based materials).

Year of construction: 2011, condition: excellent (used), Zechnical details : - Year - 2011 - Capacity - 3,2 t/h - El Power - 600 kw Line consists : - Coarse Hammer mill (110 kw ) - Transporter for dust wood - Furnace Automatic feeding unit - Furnace 1,5 MW - Dryer - three passes - Ciklon and silo for dry dust - Fine Hammer mill ( 110 kw ) - Silo ower head of presses - Pellet press TEKNU UNO ( 160 kw ) - Pellet press MUNCH ( 2X75 KW ) - Pellet pransporter up to cooler - Cooler - Seave - 2 x silo cacacity 100 t - 2x pellet transporter ( one for big bag packing 1000 kg ,and another for small bags 15 kg ) Djdpfoipt Dlex Aa Hjcl - Automatic packing unit - Robot for palletizing - reserve tools ( dies ) Factory still assemled and in production !!

Condition: refurbished (used), functionality: fully functional, machine/vehicle number: 9825, The 2024 general overhaul includes, among other things, the die head, hydraulic nut, bearings, main shaft, oil pump with filter, and synthetic oil. Only the steel housing is older but is in excellent condition. The images of the production line in the hall date from before the overhaul. The individual images of the Amandus Kahl pellet press show the condition after the overhaul. TECHNICAL DETAILS Motor power: 110 kW Sawdust capacity: 2.5 – 3 t/h Biomass capacity: 3 t/h Bran capacity: 3.5 – 4 t/h Straw capacity: 2 – 2.5 t/h L/D ratio: 3.67:1 MACHINE DETAILS Dimensions of press (W x H): 1,450 x 1,900 mm Dedpszaricjfx Aa Hscl Diameter of press: 2750 mm Insertion depth: 6 mm Press length: 22 mm Year of manufacture of motor: 2024 Year of manufacture of cooler with sieve: 2015 Year of manufacture of conveyor belt: 2015 Year of manufacture of feed screw: 2015 EQUIPMENT Amandus Kahl C35-780 pellet press with base plate New 110 kW electric motor Electric control cabinet with emergency stop Complete electrical documentation Conveyor belt Sieve system with automatic cooling Hydraulic nut Die head Electrical wiring Metering screw for product feed Automatic metering system for filling 4 additional dies, 6 mm 60 liters of additional synthetic oil 7 new bearings 2 new wear rings 1 new air filter 2 new oil seals 1 new oil filter 1 new oil pump 20 liters of 800/460 synthetic oil 1 new thrust piece (main shaft) Documentation of overhauled and renewed parts

Condition: used, Year of construction: 2003, power: 250 kW (339.91 HP), CPM 7930-4 Pellet Mill High-capacity pellet production machine manufactured by CPM. Designed for processing wood, biomass, animal feed and other pelletizable materials into pellets. The machine has been used for only one season and is in very good technical condition. Equipped with: Electric motor: 250 kW Mixer Feed screw conveyor Dcedpfx Aaozlgxbs Hol Complete set of rollers Die Manufacturer: CPM Model: 7930-4 Year of manufacture: 2003 A key machine for a complete pellet production line – ready for installation and operation.

Condition: ready for operation (used), functionality: fully functional, suction capacity: 20,000 m³/h, production capacity: 1,300 unit/h, No minimum price – guaranteed sale to the highest bidder! The hammer mill (year of manufacture 2021) has only approximately 2 operating hours! The system is suitable for straw, hay, alfalfa, compost, wood, and other agricultural raw materials! TECHNICAL DETAILS Capacity (material-dependent) max.: 1,300 kg/h MACHINE DETAILS Hammer mill power: 75 kW Pellet press: 75 kW, without control unit Bale shredder: 35 kW, including control unit Dust filter capacity: 20,000 m³/h, including control unit Dedpfx Aaezgf A Us Hjcl Operating hours Entire line: approx. 1,500 h Hammer mill: approx. 2 h EQUIPMENT Pellet press Conveyor belt Elevator Pellet cooler with screen Buffer tank with discharge 2 cyclones with rotary valve airlock Fan for cooler extraction New die Various used spare parts 10 m feed table for the bale shredder Bale shredder, including control unit Hammer mill, including control unit Centrifugal separator Big bag station for dust filter Dust separation technology: EU-ATEX Directive 2014/34 Positive dust explosion assessment from 2023 Note: The line has already been dismantled and is ready for loading.

Condition: new, functionality: fully functional, Equipment: documentation/manual, | price list | prices | prices | prices | prices | prices | prices | prices | > > > > > ecomas.pl/price-list < < < < < Djdpfx Aaexk Ta Nj Hjcl You can view the prices at the very bottom of the listing: Documents / 20215835-01.pdf We offer a high-quality, low-speed pellet granulator. The pellet mill is 100% manufactured in our plant at ECOMAS Polska Czernikowo. We guarantee equipment designed to operate continuously in a 24/7 system. Our machines produce pellets that meet EU standards – properly compacted, free of harmful additives, with a calorific value of at least 4.6 kWh/kg. The main advantage lies in modern, hardened dies and rollers (60HRC+), manufactured with CNC technology. Our dies ensure high efficiency, low power consumption, and long service life of both dies and rollers. Another benefit is the lubrication of the main shaft with oil and oversized bearings, which significantly slows down wear! Are you struggling with your current granulator – bearing failures, low efficiency, clogged die, high power consumption, rapid wear of parts, etc.? With our machines, these problems disappear. We approach each customer individually! See how our machines produce, type in YouTube: ecomas_polskie_peleciarki Available power options: 7.5kW, 11kW, 15kW, 18.5kW, 22kW, 30kW, 37kW, 45kW up to 55kW. Composition: - complete head with 2/3/4/5 rollers on cylindrical bearings - welded body – fully filled with Orlen Oil Transol VG 320 - cylindrical-bevel gearbox (efficiency 98%) - base frame - bolted dies fi 230, fi 260, fi 285, fi 310, fi 400, fi 520; hole diameters 3, 4, 5, 6, 8, 10mm (100% stability, easy disassembly, and temperature control) - standard oil tank or optional tank with pump and oil installation (oil lubrication, easy oil replacement) - user manual - 12-month warranty The buyer receives a detailed operating manual and a one-year warranty. We provide full warranty and post-warranty service.