Condition: not inspected (used), Year of construction: 2005, functionality: unexamined, workpiece height (max.): 40 mm, edge thickness (max.): 3 mm, feed rate X-axis: 35 m/min, rotational speed (max.): 12,000 rpm, number of slots in tool magazine: 48, TECHNICAL DETAILS Panel height min.: 10 mm Panel height max.: 40 mm Edge thickness min.: 0.4 mm Edge thickness max.: 3 mm Feed speed max.: 35 m/min PROCESSING UNITS Pre-milling unit Automatic engagement 48 tool positions End trimming unit 2 motors Fine trimming unit 1 2 motors Motor power: 0.55 kW Speed: 12,000 rpm Fine trimming unit 2 2 motors Gsdsyqybuepfx Abwjbi Motor power: 0.55 kW Speed: 12,000 rpm Edge scraping unit Glue scraping unit Polishing unit 2 motors Spraying device MACHINE DETAILS Control system: PC 22 EQUIPMENT Pressure applied with rubber belt Panel guides with NC positioning Glue pot for EVA hot-melt adhesive Pre-melter for EVA hot-melt adhesive Laser system (Model: LaserTec) Roller set for edge pressing with 5 pressure rollers Units mounted on safety guards CE marking The machine is sold and delivered in its actual and legal condition (“as seen and approved”), based on photo documentation and technical/commercial descriptive documentation. The buyer has the right to inspect the goods prior to collection and assumes responsibility for installation, securing, and use of the machine at the destination. External reference: 5321

Condition: not inspected (used), Year of construction: 2007, functionality: unexamined, working width: 1,935 mm, number of spindles: 40, plate height: 350 mm, working length: 6,200 mm, number of axes: 4, TECHNICAL DETAILS Working area X-axis: 6,200 mm Working area Y-axis: 1,935 mm Maximum panel thickness: 350 mm Number of edge tape magazines: 3 Number of tool positions in tool magazine: 22 (located at the rear of the machine) Gedpfx Aeyqx U Hobwebi Drilling spindles Spindles for vertical drilling: 28 Spindles for horizontal drilling in X direction: 4 Spindles for horizontal drilling in Y direction: 8 Total number of vertical + horizontal spindles: 40 Milling spindles Number of controlled axes: 4 Motor power: 10.5 kW Automatic tool changer MACHINE DETAILS Total connected load: 31 kW EQUIPMENT Suction cups for securing the workpiece Safety mats at the front Vacuum pump Waste chip conveyor Fixed groove unit for slotting in X direction The machine is sold and delivered in its actual and legal condition (“as seen and approved”) on the basis of photographic documentation and descriptive technical/commercial documents. The buyer has the right to inspect the item prior to collection and assumes responsibility for installation, securing, and operation of the machine at the place of destination. External reference: 8105

Condition: not inspected (used), Year of construction: 2008, functionality: unexamined, workpiece height (max.): 90 mm, workpiece width (max.): 3,200 mm, workpiece length (max.): 3,200 mm, edge thickness (max.): 3 mm, The machine has the following configuration: Number of panel sizing/milling units on the left side: 5 Milling unit (AS10) Double finishing cutter, top and bottom 2 pre-milling units Milling unit Number of edge processing units: 10 End trimming Top and bottom trimming (rough) Fine trimming for chamfering and rounding Corner rounding (AR34, 4 motors) Edge milling (FB40, 1 motor) Edge scraping Belt sanding (1 motor) Glue scraping Polishing (2 motors) Spray device Gbjdpfxoyq Avho Abwji TECHNICAL DETAILS Minimum panel height: 10 mm Maximum panel height: 90 mm Maximum panel length: 3,200 mm Maximum panel width: 3,200 mm Minimum edge thickness: 0.4 mm Maximum edge thickness: 3 mm FEATURES Feed chain with carriers Pressure applied via rubber belt Panel guide rails with NC positioning Edge roll magazine with 6 positions Hot melt adhesive system for PUR adhesive NORDSON Roller set for edge pressing 4 pressure rollers with NC positioning Spray device mounted on upper cabinets The machine is sold and delivered in its actual and legal condition ("as seen and approved") based on photo documentation and descriptive technical/commercial documents. The buyer has the right to inspect the goods prior to collection and assumes responsibility for installation, securing, and operation of the machine at the destination. External reference: 7685

Condition: excellent (used), Year of construction: 2020, Homag Edgeteq S-200 Year: 2020 Specification: Feed Speed 11m/min Machine Length 4605mm Workpiece Thickness max 60mm Edge Material Roll 0-3-3mm Edge Material Strips 0.4-5mm Joint trimming / pre-milling (44mm high blocks) Standard EVA glue unit Pressure zone with 1 main pressure roller + 2 idel rollers with pneumatic adjustment for thickness End Trim unit with pneumatic adjustment for chamfer / straight Top and bottom trimming unit with 2mm cutters Contour trimming unit with 2mm cutters Profile scraping with pneumatic adjustment with 2mm blades Gbjdpfx Asypm Hhebwei Additional changeable scraping heads with 1mm blades Glue Joint scraper Buffers LED indoor lighting Control system easy touch Package for construction elements Basic v Package Central Lubrication 400V 50Hz CE

Condition: excellent (used), Year of construction: 2019, Specification Gedoypm Dgspfx Abwobi 2 tanks 1 cleaning station Suitable for right sided machine such as Edgeteq S-240, S-300 and S-380 400V 50Hz

Condition: excellent (used), Year of construction: 2019, Specification: Gsdjypm Avepfx Abwebi Working height: 950mm Length: 4773mm Workpiece Thickness: 60mm Edge Material Roll: 0.4-3mm Edge Material Strip:0.4-6mm Adjustable Infeed Fence Workpiece Support Feed Speed 11m/min Central Lubrication Roller Top Pressure Manual Top Pressure Adjustment Separating Agent Spray Device Joint Trimming Unit 2x2.2kw Panel Pre-Heating QA65 Application unit for PUR Pressure Zone End Trim Unit Trimming Unit Counter Trimming unit Radius Scraping Unit with 2 sets of quick change heads Glue Joint Scraping Detergent Spraying Unit Buffers 400V 50Hz CE XES 200 with 2 tanks and 1 cleaning station including collecting tray.

Condition: used, Year of construction: 2012, total height: 1,600 mm, total length: 5,250 mm, total width: 1,440 mm, Weight: 1.550 kg Edgebander HEBROCK AKV 3006 DK FS maximum edge thickness 3/8 mm min/max. workpiece thickness 10/40 mm min. workpiece length approximately 200 mm min. workpiece width approx. 80 mm feed speed about 10 m/Min. ready in about 6 minutes. maximum power consumption 12 kW electrical connection 400 V / 3 Ph / 50 Hz Pre-mill Glue unit Pressure roller Chopping saw Milling unit Gbodpownhb Sefx Abwsi Milling unit Corner rounder Radius scraper Flat scraper Cleaning unit Dimensions (length x width x height) 5250x1445x1600 mm, weight 1550kg - Year: 2012 - Documentation available: No - CE certificate present: No - Transport dimensions: 5250mm x 1445mm x 1600mm (l x w x h) - Transport weight [kg]: 1550kg Financial information VAT: The price shown is exclusive of VAT VAT/margin: VAT deductible for entrepreneurs Delivery and trade-in always possible for everything in the industrial sectors Yorick Diebels

Condition: used, Year of construction: 2013, total height: 2,100 mm, total length: 9,000 mm, total width: 1,050 mm, Weight: 6.000 kg Price: On request - Details: - └ Description: Not working: Several loose sensors and the glue bin has been disassembled, machine has not yet been tested - Year: 2013 - Documentation available: No - CE certificate present: No - Serial number: - Number of units [pcs]: 9 - └ 1st unit type: Pre-milling unit - - Tools available: Yes - └ 2nd unit type: Glue unit - - Type/Brand: Nordson - └ 3rd unit type: Pressure rollers - - Tools available: Yes - └ 4th unit type: Cap unit - - Tools available: No - └ 5th unit type: Rough milling unit - └ 6th unit type: Milling unit - └ 7th unit type: Fine milling unit - └ 8th unit type: Milling unit - └ 9th unit type: Milling unit - - Tools available: Yes - Glue system: Glue pot - Voltage [V]: 400 - Current consumption [A]: 69 - Fuse [A]: 80 - Transport dimensions: 9000mm x 1050mm x 2100mm (l x w x h) - Transport weight [kg]: 6000kg - Transport packages [pcs.]: 4 Financial information Gbsdpsyrp Uaefx Abwei VAT: The price shown is exclusive of VAT VAT/margin: VAT deductible for entrepreneurs Delivery and trade-in always possible for everything in the industrial sectors Yorick Diebels

Condition: used, Year of construction: 2017, total height: 2,100 mm, total length: 6,700 mm, total width: 1,050 mm, Weight: 3.500 kg Price: On request - Details: - └ Description: Includes Nordson unit built in 2017 - Year: 2017 - Documentation available: No - CE marking present: Yes - CE certificate present: No - Serial number: - Number of units [pcs]: 6 - └ 1st unit type: Pre-milling unit - - Type/Brand: Nordson - - Tools available: Yes - └ 2nd unit type: Glue unit - └ 3rd unit type: Pressure rollers - - Tools available: Yes - └ 4th unit type: Rough milling unit - └ 5th unit type: Cap unit - └ 6th unit type: Fine milling unit - Voltage [V]: 400 Gbjdpfeyrpvwjx Abwoi - Current consumption [A]: 41 - Fuse [A]: 50 - Transport dimensions: 6700mm x 1050mm x 2100mm (l x w x h) - Transport weight [kg]: 3500kg - Transport packages [pcs.]: 5 Financial information VAT: The price shown is exclusive of VAT VAT/margin: VAT deductible for entrepreneurs Delivery and trade-in always possible for everything in the industrial sectors Yorick Diebels

Condition: reconditioned (used), Year of construction: 2014, functionality: fully functional, workpiece height (max.): 80 mm, edge thickness (max.): 15 mm, height adjustment type: electric, overall weight: 7,000 kg, year of last overhaul: 2023, compressed air connection: 6 bar, power of the milling unit: 3,000 W, space requirement length: 10,500 mm, Fully refurbished Topedge Duo-melt, year 2014 2 x 3Kw each Pre-milling motors 80 mm panel thickness 1 x Synchroflex top driven belt system 2 x Glue heads and tanks, Duo Melt system (For instant glue colour changes) 1 x rough trim station 1 x Bevel fine trim (can also be used for fine finishing wood in “flat” setting - adjustable angle 1 x Radius trimming machine 1 x AKF station 1 x 4 position per side AZK4 radius scraper Gbjdpjx Nbprjfx Abwoi 1 x Flat scraper 1 x Cleaning spray, front, middle and back - LCM 1 x Buffing station 2 x free spaces Infeed fence alignment for narrow panels Nesting package LCM iRelease cleaning system BrushTec ES - not included

Condition: excellent (used), Akzent edge banding machine V31 - Dimensions: 1750 x 530 x 600 mm - Plus additional 600 mm Ø roller table - Milling motor with disc cutter - Workpiece thickness: 10-55 mm Gjdpsytw Ttofx Abwsbi - Edge thickness: 0.4-1 mm - 220 Volt - 3.3 kW - Weight: 135 kg

Condition: used, machine/vehicle number: 008437, Type of edging: Thin edge, Thick edge Gluing System: EVA Hotmelt, PUR Premilling Unit: yes Corner Rounding Unit: yes Godpsyng Agefx Abwsbi Max feed speed: 12 m/min Maximum panel thickness: 60 mm Operating Units: 7 nr

Condition: ready for operation (used), Year of construction: 2006, Edgebander manufactured in 2006. This HOMAG Optimat KAL 330 features a flexible production layout for furniture parts, accommodating workpiece dimensions from 250 to 3000 mm in length and 120 to 1200 mm in width. It includes a single-sided edge banding machine capable of processing various edge materials up to 20 mm thickness. If you are looking to get high-quality edge processing capabilities, consider the HOMAG Optimat KAL 330 edgebander we have for sale. Contact us for further details. • Line workpiece capacity: • Length 250–3000 mm • Width 120–1200 mm • Thickness 8–60 mm • Edge bander (KAL 330) — base and transport • Continuous machine base; workpiece support with roller bar extendable ~800 mm • Transport chain 80 mm wide with rubber surface; precision guidance, hardened surfaces • Top pressure: driven belt • Technical data: • Feed speed 18–25 m/min • Working height 950 mm • Minimum working width: 55 mm at 22 mm thickness; 100 mm at 60 mm thickness (depending on workpiece length) • Workpiece overhang/supernatant 30 mm • Workpiece thickness 12–60 mm • Edge material from strip: 0.4–20 mm (max cross-section 900 mm²) • Edge material from coil: 0.3–3 mm (max cross-section: PVC 135 mm², veneer 100 mm²) • Max coil diameter 830 mm • Pneumatic connection 7–8 bar • Infeed system and controls (integrated with KAL 330) • Flexible workpiece infeed system wz10 for automatic infeed (lengthwise and crosswise); for precisely sized, square parts • Stepless infeed guidance adjustment (axis), speed set at input terminal • Automatic side adjustment of units (workpiece overhang 30–80 mm) for gluing and post-processing • Input terminal; solvent applicator top/bottom • Edge preparation and gluing • Pre-milling unit: 2 motors, each 4 kW, 150 Hz, 9000 rpm; electro-pneumatic control • Stepless vertical axis SF20 for automatic centering to panel thickness • Pre-melting unit with granule storage • Quick-lock system for QA/QE application unit; QA front glue storage for color change • Basic gluing unit A20; magazine height adjustment ±5 mm (manual spindle) • Extended magazine A6/A-E12/A20 for 2 coils (max Ø 830 mm); preheating station for QA/QE • Automatic pressure zone adjustment • Trimming and milling • Trimming unit HL84 with standing trimming stop for sensitive edges • Pneumatic trimming motor adjustment (2 positions: flush/level and with overhang for contour milling) • Pneumatic chamfer/straight changeover; manual side trimming stop adjustment when edge thickness changes • Rough milling unit: 2 motors stacked, each 1.5 kW, 200 Hz, 12,000 rpm; height adjustment via top pressure • Pneumatic 2-position setting: roughing with ~0.2 mm overhang / without overhang • Reserved free space for a fine milling unit • Contour milling unit Servo FK13 automatic: • 2 motors each 0.4 kW, 200 Hz, 12,000 rpm • Servo-controlled movements; automatic 8-fold tool changer • Feed speed max 20 m/min; minimum spacing between workpieces 500 mm • Workpiece thickness 12–60 mm • Automatic FK adjustment for identical radii on different edge thicknesses; auto retract • FK workpiece guidance with additional clamping for min part length 120 mm (single-sided) • Finishing and cleaning • Multi cleaning unit MN21 automatic: • Up to 3 profiles; tracing from top/bottom/side for chamfer and rounding on pre-milled PVC edges • Electropneumatic air nozzles; automatic chamfer/radius changeover; auto retract of upper/lower tool • Height adjustment via top pressure • PVC shavings separator top/bottom Gbsdpeytf Irsfx Abwji

Condition: used, Year of construction: 2013, Used machine Year of manufacture: 2013 Equipment/features: - Machine table with 13 running rollers for improved workpiece guidance - Edge feed, synchronized with the belt feed - Edge thickness adjustable via digital counter - Pneumatic roller separation with cutter (for cuttable edges) Gbsdpfoytkiujx Abwsi - Three pressure rollers - Belt feed motor 0.25 kW; approx. 1250 mm length; feed rate approx. 6.0 m/min; 50 mm wide timing belt with thick, workpiece-friendly rubber coating. Digital counter for height adjustment - Direct glue application to the workpiece: leakproof glue pot with glue supply from below and fast heat-up time after machine stoppage - Flush trimming unit for front and rear workpiece edges, automatic sensing at the workpiece, pneumatic trimming with a cutter for cuttable edges - Flush milling unit with vertical sensing and horizontal guidance, reproducible adjustment via digital counters, 2 high-performance 0.4 kW high-frequency motors, continuously adjustable from 4000 to 18000 rpm, cutter diameter 70 mm, Z4, radius 2 mm/15°; central extraction connection Ø 100 mm, 2 chip extraction hoods with hose Ø 60 mm - Automatic height adjustment of the upper cutter with the belt feed - Continuous workpiece support approx. 1800 mm long, workpiece support rail extendable by approx. 300 mm - Rotatable film disc Ø 800 mm Technical details: - Minimum workpiece width: approx. 80 mm - Workpiece thickness: 10 – 50 mm - Minimum workpiece length: approx. 220 mm - Edge thickness: 0.4 – 2.0 mm - Roller separation max.: 1.0 x 55 mm, 2 x 45 mm - Glue pot heating power: 2.7 kW - Electrical connection: 400V, 50 Hz, 3Ph + N - Total connected load: 3.8 kW - Heat-up time: approx. 10 minutes - Pneumatic connection: 6 bar - Working height: approx. 880 mm - Dimensions: approx. 1800 x 700 x 1300 mm (without film disc Ø 800) - Net weight: approx. 260 kg Availability: short-term Location: Flörsheim

Condition: used, Year of construction: 2006, Homag Optimat KAL310/6/A3/S2 Edgebanding Machine, 6-Position Tape Cart, Quickmelt Glueing Unit QA3, Approx. 1100mm Wide Machine Roller With Conveyor, Tilting Outfeed Conveyor to Return Belt Conveyor, Windows Based Control. Serial No. 0-200-15-4533 (2006). Country of Origin: Germany Gjdpfx Ajyil Arsbwobi A charge of £550 for dismantling and loading onto suitable transport will be automatically added to your invoice should you be successful in purchasing this item. Blocking and securing will be at the cost of the purchaser.

Condition: excellent (used), Year of construction: 2008, machine/vehicle number: 0-261-20-3530, functionality: fully functional, Availability: Immediately - End of March Second glue pot and interchangeable profile heads included Year of manufacture: 2008 Edge thickness (strip material): 0.4 - 12 mm Edge thickness (coil material): 0.4 - 3 mm Workpiece thickness: 8 - 60 mm Control: PC 20+ Feed speed: 10 - 18 m/min Infeed fence: Motorized SPS Electro-pneumatic infeed lock Electric pressure bridge adjustment via SPS Jointing unit: counter-rotation and co-rotation incl. DIA cutters Glue application: Quickmelt system incl. 2nd glue pot Pressure unit: 1 driven pressure roller, 3 follow-up rollers, motorized adjustment via SPS End trimming unit for front and rear trimming, pneumatically swiveling 0 - 12° Milling unit for longitudinal edges flush / bevel / radius, adjustment via SPS Corner rounding unit with 2 motors Gsdpsyt Efdofx Abwjbi Radius scraper unit with additional profile heads Flat scraper Machine length: 6,260 mm

Condition: ready for operation (used), Year of construction: 2005, Edgebander manufactured in 2005. This OTT Twister features a hot-cold melt adhesive application process and can handle edge thicknesses from 0.3 to 10 mm. It supports workpiece thicknesses of 8 to 60 mm and has a feed speed of 14-20 m/min. If you are looking to get high-quality edge banding capabilities, consider the OTT Twister edgebander we have for sale. Contact us for further details. • Adhesive application: Hot/cold melt adhesive process; application roller with synchronous and counter-rotation • Edge thickness: 0.3–10 mm • Workpiece thickness: 8–60 mm • Workpiece width: minimum 70 mm • Workpiece length: minimum 150 mm • Operating pressure: 6 bar • Feed power: 3.0 kW • Feed speed: 14–20 m/min • Electrical connection: 3x 400 V, 50 Hz • Extraction requirement: 1x Ø180 mm at 20 m/s = 35 m³/min • Air speed (minimum): 20 m/s • Compressed air consumption: approx. 300 l/minProcessing units / equipment on the machine: • Joining: • 2 x 2.2 kW, n=14,600, 250 Hz; two application-controlled working spindles • Combi-melt gluing unit: • Top-mounted, changeable hopper for EVA, PUR hot melt adhesive or cleaning granulates; hopper volume 2.5 l • AKM (automatic edge magazine): • Automatic edge magazine with optical monitoring for strip edges in fixed lengths • Capping: • 2 x 0.8 kW, n=12,000, 200 Hz; automatic swivel 0°/5°; 2 HM saw blades Ø140 x 3.2 x 16, z=34 • Flush milling: • 2 x 0.7 kW, n=12,000, 200 Hz; single-sided probing; 2 carbide-tipped indexable knife heads HF70, Ø70 x 20 x 16, z=4 • Fine milling (bevel 15°/30°/45°): • 2 x 0.3 kW, n=12,000, 200 Hz; double-sided probing; 2 carbide indexable insert cutter heads HF70, Ø70 x 20 x 16, z=4 • AWSR (radius R2–R5): • 2 quick-change sets for fine milling cutter, 2 x 0.3 kW; 2 carbide indexable insert cutter heads AR73 x 16 x 16, z=3, R2–R5 • AKF (copy milling): • Automated copy milling with two separate working spindles for end faces and longitudinal radii; 2 x 0.37 kW, 12,000 rpm; tools R1–R3 • Scraper blade: • 2 x carbide scrapers, automatic feed • Surface scraper: • 2 x carbide scrapers, with fine adjustment device Gedpfxeyn I U Re Abwjbi • PU set: • 5-way spray device (2 x release agent, 1 x lubricant, 2 x cleaning agent), fine buffing device with cloth disc • Edge cleaning: • 2 x 0.2 kW, n=2,800, 50 Hz, oscillating brushes

Condition: ready for operation (used), Year of construction: 2022, total height: 1,445 mm, product length (max.): 2,740 mm, This CASADEI Bordatrice E350PM was manufactured in 2022. It features a panel height range of 10-45 mm and supports edge band thickness from 0.4 to 2 mm. The machine operates at a feed belt speed of 7 m/min, with a glue pot heating power of 1490 W. Consider the opportunity to buy this CASADEI Bordatrice E350PM edgebander. Contact us for more information. Gbsdpfx Ajx D Icfsbwji • Panel height: 10–45 mm • Feed belt speed: 7 m/min • Edge band thickness: 0.4–2 mm • Minimum panel width: 210 mm • Minimum panel length: 600 mm • Minimum distance between panels: 95 mm • Extendable panel support opening: 310 mm • Operating pneumatic pressure: 0.65 MPa (6.5 bar) • Average air consumption: 320 Nl/cycle • Glue pot heating power: 1490 W • Machine overall dimensions (operating mode): 2740 x 1445 x 945 mm (L x H x D) • Extraction air speed: 30 m/s • Extraction air consumption: 950 m³/h

Condition: ready for operation (used), Year of construction: 2013, This IMA NOVIMAT I /G80/390/R3 edgebander was manufactured in 2013. It features dual 4.5 kW motors at 150 Hz, achieving speeds up to 9000 rpm. Capable of handling edge heights from 14 to 65 mm and roll diameters up to 850 mm, it's ideal for precise edgebanding needs. Consider the opportunity to buy this IMA NOVIMAT I /G80/390/R3 edgebander. Contact us for more information about this machine. Additional information • Motor Power: 2 x 45 kW, 150 Hz • Motor Speed: 9000 rpm • Power Supply: 230 V • Heating Power: 6 x 500 watts • Adjustment Range: Vertical approx. 17 mm, Horizontal approx. 30 mm • Stroke: Max. 8 mm • Roll Diameter: Max. 850 mm • Edge Height: 14 – 65 mm • Workpiece Projection: Min. 30 mm + edge thickness, Max. 80 mm including edge thickness • Workpiece Length: Min. 130 mm • Workpiece Gap: Min. 300 mm • Workpiece Distance: Min. 990 mm • Workpiece Thickness: Min. 8 mm, Min. 12 mm with tracing wheel, Max. 80 mm • Single Tracing Workpiece Projection: Min. 30 mm • Double Tracing Workpiece Projection: Min. 38 mm for max. 4 profiles, Max. 50 mm • Cutter Head Diameter: 125 mm • Motor Shaft: 30 x 68 mm diameter • Internal Thread: M16, Depending on motor, left or right • Cutting Cross-section Motor Power: 0.20 kW, 200 Hz 400 V, 12000 rpm for max. 195 mm², Option: 0.66 kW, Extension to max. 1100 mm² Godjx D Nh Aspfx Abwebi • Tool Diameter: 160 mm / 48 teeth • Swivel Range: 0 and 25 degrees • Workpiece Speed: Max. 30 m/min for an edge cross-section of 3 x 45 mm • Edge Overhang: Top edge, max. 3 mm, Bottom edge, max. 2 mm for straight edges • Edge Material: Edge, max. 4 mm for wood and plastic; Aluminum, max. 3 mm

Condition: ready for operation (used), Year of construction: 2016, workpiece width (max.): 40 mm, total height: 950 mm, product length (max.): 3,672 mm, This BRANDT Kantenanleimmaschine Ambition 1110 KDF 110 was manufactured in 2016. It is a single-sided edge banding machine designed for processing straight workpiece edges. With a total length of 3672 mm and a feed speed of 8 m/min, it accommodates workpiece thicknesses from 8 to 40 mm. Consider the opportunity to buy this BRANDT Kantenanleimmaschine Ambition 1110 KDF 110 edgebander. Contact us for further details. • Machine type: Single-sided edge banding machine for straight workpiece edges Gbsdpfxsyir S Nj Abwei • Feed speed: 8 m/min • Working height: 950 mm • Workpiece and edge parameters • Workpiece thickness: 8–40 mm • Workpiece width: min 70 mm (thickness 8–22 mm) or 120 mm (thickness 23–40 mm) • Edge material (rolls): 0.4–3 mm • Edge material (strips): 0.4–3 mm • Max. edge height: workpiece height + 5 mm • Processing units (aggregates) • Joint trimming unit: 2 x 0.75 kW, 200 Hz motors (one climb-milling, one counter-milling) with diamond cutters • Gluing unit (A3): Quick-change application unit; electronic thermostat for temperature monitoring • End trimming unit: 2 x 0.18 kW, 200 Hz motors for front/rear edge overhang trimming • Flush/radius trimming unit: 2 x 0.27 kW motors, manually adjustable between flush, radius, and chamfer • Profile scraper: For rounding or chamfering pre-milled PVC edges (max 3 mm) • Glue joint scraper: Removes adhesive residue in glue joint area • Control and electrical • Control unit: EASY CONTROL EC 10+ with 7" widescreen touchscreen • Program memory: Up to 20 processing programs • Supply voltage: 400 V / 3 Ph / 50 Hz • Full load current: 15.0 A • Pneumatics: Min. 6 bar • Operation and maintenance • Adjustments: Manual adjustment of units (pressure beam, trimming, pressure zone) with digital mechanical counters • Lubrication: Manual central lubrication for the transport chain (standard) • Safety: CE-conform; dust-tested (TRK max. 2 mg/m³) Technical Specification Feed Speed 8 m/min

Condition: ready for operation (used), Year of construction: 2005, Edgebander manufactured in 2005. This Bi Matic's 612 model features a gluing unit, edge trimming unit, front and rear end trimming units, trimming and beveling unit, glue scraping unit, and final polishing brushes. It also includes a 2-way dust extractor and extraction hoses. Consider the opportunity to buy this Bi Matic's 612 edgebander. Contact us for further details. • Single-sided edge banding machine • Gluing unit • Edge trimming unit • Front and rear end trimming units • Trimming and beveling unit • Glue scraping unit • Final polishing brushes Additional equipment Gjdpsyhc Tnofx Abwobi • 2-way dust extractor • Extraction hoses

Condition: ready for operation (used), Year of construction: 2009, Edgebander manufactured in 2009. This HOMAG PROFI KAR310/11/A20/S2 features a work piece return system BARBARIC. Consider the opportunity to buy this HOMAG PROFI KAR310/11/A20/S2 edgebander. Contact us for further details. Gbedpsyhqi Defx Abwoi • Condition: Used Additional equipment • BARBARIC workpiece return system

Condition: ready for operation (used), Year of construction: 2019, This SCM Olimpic K560 edgebander was manufactured in 2019. It features a 7" touch screen display with Touch 7 electronic control, supports edging thickness from 0.4 to 3 mm, and handles panel thicknesses from 8 to 60 mm. The machine offers a feed speed of 12-14 m/min and includes a hot air edge banding system. Contact us for more information. • Machine Condition: Good condition Gjdpfx Asyabq Aebwjbi • 7" touch screen display (16:9) with Touch 7 electronic control • Edging Thickness: 0.4 – 3 mm • Panel Thickness: 8 – 60 mm • Minimum Panel Length: 140 mm • Minimum Panel Width: 100 mm • Feed Speed: 12 – 14 m/min • Hot Air Edge Banding System

Condition: ready for operation (used), Year of construction: 2006, This HOMAG KFL 526 / C was manufactured in 2006. A robust double-sided edgebander, it handles workpiece thicknesses from 12 to 40 mm and sizes up to 2500 x 1200 mm. Features include a gluing unit, profile trimming, and a finish unit for precise edge finishing. Ideal for efficient edge banding with speeds up to 35 m/min. Contact us for more information about this machine. Additional equipment • Seperating agent spray device on top/bottom / Double Hogger Longitudinal/Cross: 6.6 kW with electropneumatic control / Gluing Unit A3 - 2 rolls / Profile Trimming Unit FF12 on top/bottom with motors at 12000 rpm / Finish Unit FA11 on top/bottom / Stepless stop cams with maximum cam projection of 25 mm / Standard Trimming Unit SF20 6.6 kW / Rough Trimming Unit 0.55 kW • PUR Nordson Melting Station / Tool Set / Suction Tube Machine Benefits Gjdpfxsx U Uzro Abwjbi Technical Machine Benefits • Workpiece thickness: 12 - 40 mm / minimum workpiece size (lxw): 250 x 240 mm / maximum workpiece size (lxw): 2500 x 1200 mm / maximum workpiece weight: 50 kg • Roller material edge thickness: 0. 4 - 3 mm / maximum edge cross section (plastic): 135 mm² / maximum edge cross section (veneer): 100 mm² / maximum roller diameter: 830 mm • Longitudinal processing speed: up to 35 m/min for thin edge up to 0. 6 mm /up to 30 m/min for thick edge up to 3 mm • Cross processing speed: up to 30 m/min for panel sizing/ up to 20 m/min for edge processing • Minimum workpiece gap: 500 mm

Condition: ready for operation (used), Year of construction: 2019, This SCM E10 edgebander was manufactured in 2019. It features a 0.4 to 3 mm edgebanding thickness capacity and can handle panel heights from 8 to 80 mm. The machine supports minimum panel dimensions of 50 mm in width and 210 mm in length. It operates with two feed speeds of 4 and 8 m/min and a maximum temperature range of 140 to 220 degrees C. Installed motor power is 3.5 kW. Contact us for more information about this machine. • Edgebanding Thickness Capacity: 0.4 to 3 mm • Thickness of Edges with Shear Device: • (80 mm height) 0.4 to 1.5 mm • (50 mm height) 0.4 to 2.5 mm • (45 mm height) 0.4 to 3 mm • Panel Height Capacity: 8 to 80 mm • Edge Height: 10 to 83 mm • Minimum Panel Width: 50 mm • Minimum Panel Length: 210 mm • Minimum Internal Radius with 0.4 mm Edgebanding: • Concave: 25 mm • Convex: 5 mm • Feed Speeds: 4 and 8 m/min • Maximum Operating Temperature: 140 to 220 degrees C Gedsyabmkjpfx Abwobi • Installed Motor Power: 35 kW • Overall Dimensions: 39.37" x 29.13" x 43.3"