Condition: as good as new (ex-display), Year of construction: 2022, Briquetting press for aluminium or steel chips Extremely high pressing force of 3,700 kg/cm² Large storage silo Briquette size: 60 x 40 mm Kdjdpfx Ajw Ig Sueg Ueg Throughput: Aluminium chips – up to approx. 70 kg/h Steel chips – up to approx. 100 kg/h Brass chips – up to approx. 100 kg/h *depending on feedstock Included: - Emulsion tray - Emulsion pump - Oil cooler

Condition: reconditioned (used), Year of construction: 2023, All wear parts new only 704 operating hours Special price for a low-hour demonstration unit Base machine: €29,990 net Optional extras (for an additional charge): - Cooling unit: €3,995 net - Emulsion tray: €3,990 net The hydraulic briquetting presses of the MPP NEM series compact materials such as aluminum, copper, brass, bronze, graphite, and other non-ferrous metals into dimensionally stable cylindrical briquettes. These machines are distinguished by their robust construction, ensuring consistent briquette quality during continuous operation. The pressing process does not require any binding agents – compaction is achieved solely through hydraulic pressing force. Depending on material, the feedstock volume can be reduced by up to 90%. Throughput capacity: maximum 70 kg/h (depending on material) Briquette diameter: Ø 50 mm Motor: 5.5 kW 400 Volt / 50 Hz / 3-phase Pump: 40 liters Maximum briquette length: 50 mm Optimal briquette length: 40 mm Silo diameter: 1,000 mm Oil tank: 110 liters Dimensions: 1750 x 1130 x 1100 mm (L x W x H) Weight: 950 kg Kdodjd N Dnhjpfx Ag Uog Hydraulic pre-compaction via slide Main press cylinder Vertical cylinder Fill level sensor: yes Feed material requirements: - Max. chip length: 15 mm - Installation room temperature: heated space, at least +5°C - Max. load on agitator: 150 kg - Feed material must be free from magnetic metals and mineral contaminants such as sand, stones, etc. Damage to pressing tools and/or increased wear may otherwise occur.

Condition: good (used), Year of construction: 2013, functionality: fully functional, pressing force: 34 t, power: 7.5 kW (10.20 HP), L&M H900 stationary press + container The H900 has a raised press block (900mm) and is specially designed for extremely large pieces / quantities of cardboard. The machine is powered by a 7.5 kW electric motor. Originally built in 2008 and overhauled by Wortmann Milieutechniek in 2013. This machine has been maintained by Wortmann Milieutechniek, the entire maintenance history is available. Kdsdpfxewcd Nne Ag Uog Immediately ready for use!

Condition: used, Year of construction: 2000, functionality: fully functional, pressing force: 70 t, For sale: a fully functional and well-maintained Husmann MP6070-TS waste compactor installation, currently still in daily operation. Kdjdpoxuhtrofx Ag Usg The installation is immediately ready for use and is particularly suitable for compacting and transferring various waste streams. Features: - Fully operational and functional installation - In daily use and well maintained - Includes two swap bodies for moving containers - Equipped with hydraulic container couplings and a hydraulic container locking system - Features a large feed hopper - Can be easily filled with a wheel loader, excavator, or from a platform/ramp - Immediately available for use Containers are not included.

Condition: good (used), Year of construction: 2001, functionality: fully functional, KAMPWERTH SHD 1600 horizontal baler, incl. 3 interchangeable containers 48000x2800x3000 Paper baler // Waste baler // Refuse baler Baler, 1 unit • Type: Kampwerth SHD 1600 • Year of manufacture: 2001 • Unladen weight: 3,500 kg • 15 kW • Dimensions: 5000x2300x3700 mm (disassembled for transport) Container box for baler, 3 units • Year of manufacture: 2001 • Volume: 28 m³ • Unladen weight: 3,100 kg • Filling weight: 12,000 kg • Dimensions: 7000x2400 mm Kodpfsxm Skrsx Ag Uedg Location: Bielefeld

Condition: excellent (used), Model Baler HSM V-press 1160 plus Pressing force (kN): 59 Output (bales/h): 1-2 Ksdpfx Agjv Al Tie Ujdg Max. bale size (mm): 1200x1100x1000-1200 Dimensions L x W x H (mm): 1780x1150x2985 Power (kW): 4 kW Weight (kg): 2300 Year of manufacture: 2017-2021 2018 unit – price: 8,000 EUR

Condition: excellent (used), Year of construction: 2023, operating hours: 1,851 h, functionality: fully functional, pressing force: 70 t, filling opening width: 1,100 mm, filling opening length: 1,400 mm, bale width: 1,100 mm, bale height: 750 mm, bale weight: 500 kg, overall weight: 17,000 kg, oil tank capacity: 70 l, Technical data baler: Manufacturer Avermann Maschinenfabrik GmbH & Co. KG, Germany Type AVOS 1410 BS-22/50 Year of construction 2023 Pump operation hours 1,851 hours, as of July 24 Press power main press 70 t (a 70 tonne hydraulic cylinder is installed, special equipment) Specific press force 90,9 N/cm² (a 70 tonne hydraulic cylinder is installed, special equipment) Feed channel 1,400 x 1,000 mm Theoretic cycle time 13 sec Theoretic throughput capacity 266 m³/h Bale size 1,100 x 750 (w x h), the length is variable Drive power 22 kW Connected load 65 kW Tying system 4-fold, vertical, fully automatic Throughput capacity at a bulk weight of 30 kg/cbm approx. 5,5 t/h bulk weight of 50 kg/cbm approx. 7,5 t/h bulk weight of 100 kg/cbm approx. 9,7 t/h Bale weight with a bale length of approx. 1.2 m up to 500 kg, depends on material SPS controller Siemens S7-1500 Operating panel Schneider Harmony Baler dimensions built up 8,610 x 2,400 x 3,835 mm (l x w x h) Transport weight baler approx. 17 t Kdodpfju Thbxex Ag Usg Special equipment: Wear-resistant floor made of HARDOX steel Larger main hydraulic cylinder with 70 tonnes of pressing force Special press ram for pressing loose bulk materials with small grain sizes OptiCut XS system for lower cutting forces and higher throughput rates Special pressing piston for pressing "difficult" materials Technical data for the conveyor belt: Manufacturer Avermann Maschinenfabrik GmbH & Co. KG, Deutschland Type KGF GB 1500 Year of construction 2023 Drive power 4.0 kW Belt speed approx. 0.3 m/second Length feeding conveyor 2,679 mm Length elevating conveyor 6,866 mm Length goose neck 1,272 mm Grade 35° Effecting width 1,400 mm Side wall height 800 mm Carrier height 50 mm Carrier distance 750 mm Belt quality EP 400/3, 3:1 (DIN quality N) Overall height 4,515 mm Overall transport dimensions11,148 x 2,502 mm (l x w) Technical data on the non-contact personal protection system: Manufacturer BOREMA Umwelttechnik AG, Switzerland Type APSS iBOR 22 Year of construction 2023 Condition of the press system: The entire system is in very good condition due to the short operating time of only 1,851 pump hours and the processing of only paper, cardboard and film. Scope of delivery: Avermann baler, type AVOS 1410 BS-22/50, incl. wire drawing stations and bale chute Avermann conveyor belt, type KGF GB 1500 BOREMA personal protection system, type APSS iBOR 22 Comments: The documentation (Manual, CE-declaration, electr./hydr.-drawings), are completely available. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors.

Condition: good (used), Year of construction: 2019, operating hours: 673 h, functionality: fully functional, pressing force: 60 t, filling opening width: 1,100 mm, filling opening length: 1,400 mm, bale width: 720 mm, bale height: 1,100 mm, overall weight: 12,500 kg, oil tank capacity: 800 l, power: 37 kW (50.31 HP), Technical data baler: Manufacturer Riko Ekos d.o.o Type S-60K (5) Year of construction 2019 Operating hours 673 hours, as of August 24 Number of pressed bales 1,127 bales, as of August 24 Pressing force main press 60 tonnes Dimensions of feed chute 1,100 x 1,400 mm Filling volume / pressing cycle 2.1 m³ Bale dimensions 720 x 1,100 mm (W x H), the length is variable Drive power 37 kW Connected load, total 47 kW Tying 4-fold horizontal, fully automatic Throughput capacity with a bulk density of 30 kg/cbm approx. 5 - 6 tonnes/hour Bulk weight of 50 kg/cbm approx. 9 - 11 tonnes/hour Bulk weight of 100 kg/cbm approx. 15 - 19 tonnes/hour Filling volume of hydraulic oil tank 800 litres PLC control Siemens SIMATIC S7-1200 Siemens SIMATIC HMI control panel Press dimensions assembled without hopper and chute 12,220 x 3,654 x 2,685 mm (L x W x H) Effective transport dimensions excluding press, with dismantled tying system 7,230 x 1,750 x 2,685 mm (L x W x H) Transport weight press 12.5 tonnes Condition of the baler: The machine is part of a sorting line and was only partially used for pressing individual material flows. The machine is now no longer needed and has therefore been sold. However, the baler is regularly put into operation once a week for two to three bales so that the machine remains in working order. Due to the extremely low operating hours, the baler is in good condition and ready for immediate use. Scope of delivery for the baler: 1 piece baler without conveyor belt, hopper and chute 8 pieces wire pulling stations, without wire 1 piece bale chute 1 set of machine documentation Kdjdpfx Ageu Thicj Ueg Comments: The documentation (Manual, CE-declaration, electr./hydr.-drawings), are completely available. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors.

Condition: reconditioned (used), Year of construction: 1996, functionality: fully functional, pressing force: 170 t, filling opening width: 1,020 mm, filling opening length: 1,800 mm, bale width: 1,100 mm, bale height: 1,100 mm, overall weight: 40,000 kg, oil tank capacity: 3,000 l, year of last overhaul: 2024, For sale is a used baling press system consisting of a chain belt conveyor for underfloor operation, with a feed hopper, a hydraulic pre-compactor with whirlulator, a MACPRESSE 111A baling press, two complete wire drawing frames with 5 wire reel stands each, without wire. Technical data baler: Manufacturer MACPRESSE EUROPA S.R.L. Typ 111A Year of construction 1996, refurbished in 10/2024 Press power main press 170 tons Specific press capacity 14 kg/cm² Feed channel 1,800 x 1,020 mm Filling volume 2,5 cm³ Theoretic throughput rate 750 m³/h Bale size 1,100 x 1,100 mm, length variable Driving motor 2 x 55 kW Tying system 5-fold horizontal, full automatic Throughput rate at a approx. 30 up to 35 tons/h, depends on material Volume hydraulic oil tank 3,000 l Transport dimensions of press with new machine feets 113,700 x 2,300 x 2,900 mm (l x w x h) Machine weight baler approx. 40 tons Comments: The baler was partially overhauled in our workshop and tested after completion of the work, please look at our functional video. The system was previously used to bale paper and cardboard from municipal collections. The contract was awarded elsewhere after the end of the contract period, so the complete system is for sale. The overhaul work carried out and the spare parts replaced can be found in the detailed photo documentation and in our quotation. The documentation (Manual, CE, electr./hydr.-drawings), are completely available. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors. Kodeu Th D Rjpfx Ag Uodg Technical data conveyor belt: Manufacturer Wagensfeld B.V. Type chain belt conveyor 1700 mm Year of construction 2017 Drive power 7.5 kW Belt speed 14 m/minute Length of infeed conveyor 6,900 mm Length of ascending belt 12,885 mm Length of gooseneck 1,747 mm Overall length 21,271 mm Pitch 32° Effective width 1,644 mm Height of drive shaft above ground 5,777 mm Wall height of feed conveyor 500 mm Wall height of ascending conveyor 880 mm Steel flights height 40 mm Distance between flights 1200 mm Transport dimensions conveyor disassembled 15,005 x 2,503 x 2,435 mm (l x w x h) Pit dimensions 11,500 x 2,700 x 1,015 mm (l x w x d) Remarks: The chain belt conveyor, built in 2017, was later made to fit the baler during the last installation of the baler in the Netherlands and is newly installed. The conveyor belt is in good, operational condition and has therefore not been overhauled. An installation drawing with the pit dimensions is available. Scope of delifery: 1 chain belt conveyor, Wagensveld B.V. 1 piece feed hopper with pre-compressor flaps 1 piece wirbulator 1 baler MACPRESSE, type 111A 2 wire drawing frames with wire reel stands, without wire 1 operating manual with CE declaration, electrical and hydraulic circuit diagram

Condition: good (used), Year of construction: 2010, operating hours: 3,641 h, functionality: limited functionality, pressing force: 36 t, filling opening width: 1,100 mm, filling opening length: 1,080 mm, bale width: 1,100 mm, bale height: 750 mm, power: 15 kW (20.39 HP), empty load weight: 4,000 kg, volume flow: 90 m³/h, Technical data baler: Kdsdpfxeu Thh Ej Ag Uog Manufacturer Presto GmbH & Co. KG Typ CC 36 M Year of construction 2010 Hours of operation 3,641 h Press power main press 36 t Specific press capacity 467 N/cm² Feed channel 1.080 x 1100 mm (l x w) Cycle time 34 sec. Capacity per cycle time 0,85 m³ Theoretic throughput rate 90 m³/h Throughput rate under operating conditions with a material bulk density of 35 kg/m³ approx. 51 m³/hour Bale size 1100 x 750 mm (w x h), length variable Driving motor 15 kW Tying 4-fold vertical, semi-automatic, with polyester synthetic yarn Throughput rate at a bulk weight of 35 kg/cbm 1,8 to/h bulk weight of 60 kg/cbm 2,5 to/h bulk weight of 100 kg/cbm 3,1 to/h Transport dimensions only baler 4.200 x 1.640 x 2.200 mm Machine weight baler approx. 4 to Comments: The press was checked for function in our workshop, then stored and is therefore available at short notice. The machine documentation (operating ins3.641tructions, CE, electrical and hydraulic circuit diagram) is available. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors.

Condition: good (used), Year of construction: 2019, operating hours: 2,320 h, functionality: fully functional, pressing force: 60 t, filling opening width: 1,100 mm, filling opening length: 1,400 mm, bale width: 720 mm, bale height: 1,100 mm, overall weight: 12,500 kg, oil tank capacity: 800 l, power: 37 kW (50.31 HP), Technical data baler: Manufacturer Riko Ekos d.o.o Type S-60K (6) Year of construction 2019 Operating hours 2,320 hours, as of August 24 Number of pressed bales 4,359 bales, as of August 24 Pressing force main press 60 tonnes Dimensions of feed chute 1,100 x 1,400 mm Filling volume / pressing cycle 2.1 m³ Bale dimensions 720 x 1,100 mm (W x H), the length is variable Drive power 37 kW Connected load, total 47 kW Tying 4-fold horizontal, fully automatic Throughput capacity with a bulk density of 30 kg/cbm approx. 5 - 6 tonnes/hour Bulk weight of 50 kg/cbm approx. 9 - 11 tonnes/hour Bulk weight of 100 kg/cbm approx. 15 - 19 tonnes/hour Filling volume of hydraulic oil tank 800 litres PLC control Siemens SIMATIC S7-1200 Siemens SIMATIC HMI control panel Press dimensions assembled without hopper and chute 12,220 x 3,654 x 2,685 mm (L x W x H) Kdedpju Thipefx Ag Ujg Effective transport dimensions excluding press, with dismantled tying system 7,230 x 1,750 x 2,685 mm (L x W x H) Transport weight press 12.5 tonnes Condition of the baler: The machine is part of a sorting line and was only partially used for pressing individual material flows. The machine is now no longer needed and has therefore been sold. However, the baler is regularly put into operation once a week for two to three bales so that the machine remains in working order. Due to the extremely low operating hours, the baler is in good condition and ready for immediate use. Scope of delivery for the baler: 1 piece baler without conveyor belt, hopper and chute 8 pieces wire pulling stations, without wire 1 piece bale chute 1 set of machine documentation Comments: The documentation (Manual, CE-declaration, electr./hydr.-drawings), are completely available. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors.

Condition: excellent (used), operating hours: 2,658 h, functionality: fully functional, pressing force: 71 t, filling opening width: 1,000 mm, filling opening length: 1,620 mm, bale width: 1,100 mm, bale height: 720 mm, bale weight: 600 kg, input current: 200 A, oil tank capacity: 1,250 l, empty load weight: 29,000 kg, Technical data baler: Manufacturer BOA Recycling Systems B.V. Type M75-45-A-5-1.6 Ecoline Year of construction 2021 Hours of operation 2,658 hours (as of May 2024) Number of pressed bales 42,212 pieces (as of May 2024) Press power main press 71,2 kN (71 t) Specific press capacity 9 kg/cm² Operating pressure 280 bar Cylinder stroke 2,200 mm Feed channel 1,620 x 1,000 mm Capacity per cycle time 2,4 m³ Theoretic cycle time 21 seconds Theoretic throughput rate 450 m³/hour Bale size 1,100 x 720 mm, length variably adjustable up to 1,400 mm Driving motor 45 kW Connected load 100 kW Current consumption 200 A Tying system 5-fold vertical, fully automatic, the press stamp is prepared for an additional 3-fold horizontal binding Throughput rate at a bulk weight of 30 kg/cbm approx. 13,6 tons/hour bulk weight of 50 kg/cbm approx. 24,2 tons/hour bulk weight of 100 kg/cbm approx. 36,4 tons/hour bulk weight of 150 kg/cbm approx. 54,7 tons/hour Bale weight up to 600 kg, depends on material Volume hydraulic oil tank 1,250 l Kedpsu Thcvefx Ag Ujdg SPS controller Siemens S7 1500 Operating panel Siemens SIMATIC HMI TOUCH Transport dimensions of press 10,000 x 2,800 x 3,385 mm (l x w x h) Press height set up with feed chute 4,743 mm Press height with conveyor belt 7,123 mm Machine weight baler approx. 29 tons Noise level <85 dB (A) Condition of the baler: With 2,658 operating hours, the press is almost as good as new and in very good condition, has hardly any signs of wear and is ready for immediate use. Due to larger material input quantities, the pressing force and throughput of the machine no longer meet the customer's current requirements and is therefore being replaced by a new 120 tonne baler. Only the baler is for sale, without conveyor belt and wire drawing stations. Comments: The documentation (Manual, CE, electr./hydr.-drawings), are completely available. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors.

Condition: reconditioned (used), Year of construction: 2007, operating hours: 22,605 h, functionality: fully functional, pressing force: 100 t, filling opening width: 1,100 mm, filling opening length: 1,600 mm, bale width: 1,100 mm, bale height: 1,100 mm, bale weight: 1,400 kg, input current: 238 A, overall weight: 36,000 kg, oil tank capacity: 1,300 l, For sale is a overhauled baler, with 100 tonnes pressing force, large format 1100 x 1100 mm, 75 kW drive power and 10-fold cross binding Technical data baler: Manufacturer Bollegraaf Typ HBC 110 K / 75 kW Year of construction 2007 Press power main press 100 tons Press power of pre-press 50 tons Operating hours 22,605 hours Feed channel 1,600 x 1,100 mm Capacity per cycle time 3,15 m³ Theoretic cycle time 19 sec. Bale size 1,100 x 1,100 mm Driving motor 75 kW Connected load 126 kW Full load current 238 A Kodpevf E Avofx Ag Uedg Tying system 5-fold vertical, 5-fold horizontal, fully automated Throughput rate at a bulk weight of 30 kg/cbm approx.16 tons/h bulk weight of 50 kg/cbm approx. 25 tons/h bulk weight of 100 kg/cbm approx. 47 tons/h Bale weight up to 1400 kg, depends on material and bale lenght Volume oil tank approx. 1,300 l SPS controller Telemecanique TSX Micro Operating panel Schneider MAGELIS Touch Baler dimensions built up with hopper 11,750 x 5,000 x 7,105 mm (l x w x h) Transport dimensions only baler 11.750 x 2.500 x 3.450 mm (l x w x h) Machine weight baler approx. 36 tons Comments: The press was partially overhauled and serviced in our workshop and tested and stored after completion of the work. The machine is available at short notice and can be inspected in our warehouse by appointment. The following overhaul work was carried out: Rust removal and partial painting of the press. Remaining hydraulic oil tank drained, oil filter and air filter replaced. New hydraulic oil topped up. All hydraulic hoses replaced. Main hydraulic cylinder, two cylinders of the prepress flap and the cylinder of the press channel dismantled, disassembled, checked, cylinder tubes honed, all seal sets replaced and a final pressure test carried out. Disassembly of the prepress flap with bearings and bearing blocks. 1st and 3rd circular arc segmet cut out and a new one welded in again. Both bearings of the shaft of the prepress flap replaced. Upper material deflector on the frame of the prepress flap replaced. Press ram dismantled, checked and both front rollers replaced. Material deflectors and wear profiles on the sides and base of the press ram cut off and new ones welded in. Horizontal and vertical needle and tying unit dismantled, disassembled, checked, plastic sliding plates, bearings of the drill shafts and wire deflection rollers with bearings in the needle heads replaced. Both bronze slide rails on the left and right in the frame cover to the press ram replaced. Both wire deflection units on the left and right, with bale retaining clamps, completely renewed. Wire insertion unit including hydraulic cylinder under the needle feedthroughs completely renewed. Wire entry marks in the floor and side walls of the bale chamber welded shut and smoothed. General maintenance and service work carried out in accordance with the manufacturer's specifications. Press was tested in manual and automatic mode, accepted and stored after completion of overhaul work. We accept no liability for the technical specifications or any errors.

Condition: excellent (used), Year of construction: 2022, functionality: fully functional, Technical data on the EPS (Polystyrene) press: Manufacturer FZ-Recycling GmbH & Co. KG, Germany Type FZR 320 Year of construction 12/2022 Drive power shredder 4 kW Drive power of compactor screw 7.5 kW Drive power hydraulic unit for the holding clamp in the press channel 1.1 kW Total connected load 12.6 kW Kdsdsu Thkaepfx Ag Ueg Current consumption 32 A Compaction ratio of the compacted blocks to the original product approx. 50:1 (depending on material) Block weight after compaction approx. 300kg/m³ (depending on material) Block dimensions 320 x 320 mm, variable length Throughput approx. 100 kg/hour, depending on material Achievable density approx. 250 - 300 kg/m³ The pressed blocks are stacked approx. 1400 mm high on pallets and stretch-wrapped. Machine dimensions approx. 4,600 x 1,400 x 1,980 mm (l x w x h) Transport weight press 1,325 kg Condition of the baler: The press was only used sporadically, is in very good condition and available at short notice. Due to the low weight of the machine and the forklift shoes in the transport frame, the press is mobile and can be used directly on the construction site where the material is produced. The electrical connection is made via a CEE 32 A plug. Scope of delivery for the baler: 1 piece EPS press, ready for connection and use Comments: The documentation (Manual, CE-declaration, electr./hydr.-drawings), are completely available. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors.

Condition: ready for operation (used), DIXI 60SLD is a semi-automatic baling system with a pressing force of 60 tons, designed for economical volume reduction of recyclable residues in industrial and craft sectors: - Cardboard boxes - Foams - PET bottles - Insulation mats - and other pressable materials Kdsdpfera A E Usx Ag Ueg Horizontal baler, DIXI 60 SLD waste press with tipping device Technical specifications: Pressing force: 60 tons Specific pressure: 6.81 kg/cm² Power supply: 400V / 7.5kW Bale dimensions: 800 x 1100 x 1200 mm Number of ties: 3 Bale weight: approx. 370–410 kg Tying: manual Feed opening: 990 x 1110 mm Machine weight: 5,420 kg Average pressing cycle: 47 sec Year of manufacture: 2011–2016 Dixi 80SLD Baler Technical Data of the Baler Brand: Dixi Model: 80 SLD Pressing force: 80 tons Drive power: 11 kW, 400 V / 32 A Feed opening (W x H): 1040 x 1110 mm Pressing cycle: approx. 35 sec Throughput: approx. 1,000 kg/h Bale size (W x H x L): 1120 x 1120 x 1200 mm Bale weight: depending on material, approx. 500–600 kg Bale tying: triple, manual Machine dimensions: Length: 4,200 mm (+cage 1,600 mm) Width: 1,830 mm Height: 2,620 mm Machine weight: approx. 8,000 kg Automatic bale ejection Robust construction for long-term use Year of manufacture: 2016–2020 Weight: approx. 8.4 tons Condition: Used

Condition: ready for operation (used), HSM V-Press 860 Baler, year 2008-2009, price: €5,800 Pressing force: 54 kN Specific pressure: 63.46 N/cm² Drive motor power: 7.5 kW Cycle time: 25 s Loading height: 1110 mm Loading aperture (W x H): 1195 x 650 mm Bale dimensions (L x W x H): 1200 x 780 x 1200 mm Bale weight: 480 kg Machine dimensions (W x D x H): 1797 x 1247 x 2985 mm Machine weight: 2008 kg Binding material: wire Pressed materials: foil, mixed paper, cardboard, die-cut waste, textiles, Big Bags, polystyrene HSM V-Press 860 Plus, year 2013-2015, price: €7,500 HSM V-Press 860 L, year 2015, price: €9,000 HSM V-Press 860 Plus, year 2019, price: €9,000 HSM V-Press 860, brand new, ex-display, year 2020, price: €13,000 Bale binding: 4-fold wire tying Bale dimensions (L x W x H, mm): 1200 x 800 x 1000 - 1200 Bale weight (approx.): 500 kg Technical data (L x W x H, mm): 1213 x 1824 x 2987 Filling aperture (mm): 1200 x 565 Cycle time (seconds): 35 Kdedpfx Aera Rbgog Ueg Pressing force (T): 54 Power supply (V): 400 (three-phase) HSM V-Press 860 Plus B, year 2020, price: €14,000 Press force: 594 kN Voltage/frequency: 400 V/50 Hz Power: 4 kW Filling opening (W x H): 1500 x 651 mm Bale size (L x W x H): 1500 x 780 x 1200 mm Bale weight: 550 kg Loading type: manual Machine dimensions (W x D x H): 2099 x 1245 x 2985 mm Machine weight: 2336 kg Binding material: wire Suitable materials: foil, cardboard Idle cycle time: 25 s

Condition: ready for operation (used), Year of construction: 2012, pressing force: 40 t, Manufacturer: HSM Model: HL 4010 Year of manufacture: 2012 Kjdpjx D U N Sjfx Ag Uodg

Condition: used, Year of construction: 2006, operating hours: 54,050 h, pressing force: 80 t, filling opening width: 1,020 mm, filling opening length: 1,600 mm, bale width: 1,100 mm, bale height: 750 mm, bale weight: 750 kg, oil tank capacity: 2,100 l, power: 94 kW (127.80 HP), empty load weight: 21,000 kg, Technical data baler: Manufacturer Paal Typ Konti 275 E Year of construction 2006 Hours of operation in total 54,050 hours Press power main press 80 tons at 300 bar Specific press capacity 9,7 kg/cm² Feed channel 1,600 x 1.020 mm (l x w) Throughput capacity under operating conditions 350 m³/hour Bale size 750 x 1,100 mm, length variable Driving motor 75 kW Connected load 94 kW Rated current 180 A Tying system 4-fold vertical, fully automatic Bale weight up to 750 kg, depends on material Volume hydraulic oil tank 2,100 l SPS controller (manuf., type) Siemens Simatic S7-300 Operating panel (manuf., type) Siemens Multi Panel Transport dimensions only baler 11,152 x 2,152 x 3,000 mm (l x w x h) Machine weight baler approx. 21 tons Condition of the baler: The press and conveyor belt are in satisfactory working condition, see photo documentation. Further technical data and dimensions for the conveyor belt are not currently available. The plant is currently still in operation and is to be replaced by a larger press plant in the coming months. Scope of delivery: Ksdpfoxcxm Esx Ag Uedg Bale press, bale chute, conveyor belt and machine documentation. Comments: The documentation (Manual, CE, electr./hydr.-drawings), are completely available. Dismantling and loading is the responsibility of the buyer. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors.

Condition: reconditioned (used), Year of construction: 2001, functionality: fully functional, machine/vehicle number: HBC 140 2x75kW 2001 (210-008-01), pressing force: 155 t, bale weight: 1,500 kg, pressure: 250 bar, power: 150 kW (203.94 HP), year of last overhaul: 2024, Equipment: documentation/manual, Sold by Bollegraaf Recycling Solutions, the original manufacturer of this Bollegraaf baler and conveyor: Bollegraaf HBC140s Baler (2x75kW). Baler: Weight: 47.100 kg Construction year: 2008 Hardox bottom floor plate only Variable channel pressure control Plastic valve Hydraulic pump driven by frequency inverter Anti-rat cabling Oil in-depth filtration Modem Hours 40.000 This baler can also be sold fully refurbished according to the 'Bollegraaf OEM Certified Refurbishment standards'. This includes 2 year guarrantee. Contact us for more information or a quotation. General principles of refurbishment Cleaning & disassembly Before the actual refurbishment takes place the baler is completely cleaned and disassembled in our refurbishment workshop. Tolerances After the disassembly the tolerances of all steel components are measured and re-welded where necessary, this at least applies to the following components; • Ram, • Frame, • Channel, Kedpfx Agotvau As Uedg • Pre-press-flap After disassembly and inspection the ram is welded-up again and fitted with new ram wheels. The protective grids and the pre-press flap are made dent-free and repaired where necessary. Repainted After measuring the tolerances and any repair- and welding work, all components are being blasted and coated again. Hydraulics: The hydraulic tank is cleaned. The hydraulic lines & hoses are replaced. The hydraulic components are repackaged. The hydraulic oil is replaced. Cabling: All cabling is checked and replaced if necessary. All junction boxes are replaced and placed back in easily accessible positions. Wear parts: All wearing parts are replaced. The pins and shafts of the cylinders and the channel are replaced with new ones. All wearing parts of (both) needle installations and knotters are replaced for new. Cylinders: The cylinders are repackaged and, if necessary, provided with a new chrome layer or a new cylinder rod. MCC Cabinet The switch box is checked and cleaned. If necessary, electronic components are replaced with new ones. The PLC and HMI (human interface) are replaced with the latest Schneider M340 version including the latest software.

Condition: reconditioned (used), Year of construction: 2003, functionality: fully functional, machine/vehicle number: W230-028, pressing force: 80 t, warranty duration: 24 months, pressure: 250 bar, power: 45 kW (61.18 HP), year of last overhaul: 2024, Equipment: documentation/manual, Sold by Bollegraaf Recycling Solutions, the original manufacturer of this Bollegraaf baler. Kdedpfx Agstvat To Ueg This is a baler HBC80 (45kW) with crosswires. At the time of writing this baler is being completely refurbished in our refurbishment workshop. This refurbishment takes place on the basis of the very strict Bollegraaf OEM Refurbishment Guidelines. After refurbishment, this baler is sold with a 2-year warranty.

Condition: reconditioned (used), Year of construction: 2008, operating hours: 23,000 h, machine/vehicle number: 00834, pressing force: 60 t, filling opening width: 1,100 mm, filling opening length: 1,315 mm, bale width: 1,100 mm, bale height: 720 mm, warranty duration: 3 months, power: 30 kW (40.79 HP), year of last overhaul: 2025, Equipment: documentation/manual, Bollegraaf Recycling Solutions, the original manufacturer of this Bollegraaf baler, hereby offers the following machine(s) A repaired HBC60 (30kw) Repaired – in very good technical condition Year of construction: 2008 Volume capacity m3/hr max. 365 334 321 301 Volume weight kg/m3 max. 15 30 50 80 Weight capacity T/hr max. 5.5 10 16 24 Bale weight 400 – 800 kg, depending on S.G. of material and bale length Bale length - adjustable Bale height - 720 mm Bale width - 1100 m Filling opening - 1100 mm x 1320 mm Max. size supply - 1500 mm x 1200 mm Pressure force ram - max 60 tonf. Pressure force pre-press flap - max 25 tonnes Cycle time - 18 seconds Motor - 45 kW Motor Twistomat - 2.2 kW Motor counter pressure pump - 1.1 kW Following repairs have been done in our official Bollegraaf OEM Refurbishment Workshop: * Safety doors needle installation replaced with new Kodpfx Ajxck U Usg Ujdg * Ram wheels behind replaced with new * Bronze strip above ram replaced with new * Movable beam position switch ram replaced with new * Scraper above ram replaced with new * Sealing pre press cylinders replaced with new * New steel beams channel cylinder * nieuwe buisjes oplassen en wielen gangbaar maken * New pusher cylinder underneath vertical tying unit * Safety hatch behind needle installation replaced with new * Several cables and asi modules replaced with new * New air filter * New oil filters

Condition: good (used), Year of construction: 2012, operating hours: 12,078 h, functionality: fully functional, pressing force: 88 t, filling opening width: 1,100 mm, filling opening length: 1,800 mm, bale width: 1,100 mm, bale height: 750 mm, bale weight: 750 kg, overall weight: 30,000 kg, oil tank capacity: 2,000 l, power: 98 kW (133.24 HP), volume flow: 643 m³/h, Technical data baler: Manufacturer HSM GmbH + Co. KG, Germany Type VK 8818 R-FU Year of construction 2012 Total operating hours: 12,078 hours, as of September 2025 Pump operating hours 6,616 hours (effective pump running time) Number of bales pressed: 65,792 bales, as of September 2025 Main press force 880 kN Specific pressing force 120 N/cm² Pressing force cutting edges free rammer 120 kN Dimensions of feed chute 970 x 1,800 mm Theoretical cycle time in idle mode 8.3 seconds Theoretical throughput capacity 643 m³/hour Bale dimensions 1,100 x 750 mm, the length is variable 600 up to 2000 mm Drive power 2 x 45 kW frequency-controlled Connected load 98 kW Total current consumption 192 A Fuse protection 250 A slow-blow 5-fold horizontal tying, fully automatic Throughput rates with a bulk density of 20 kg/cbm 12.86 t/hour Bulk weight of 50 kg/cbm 32.15 t/hour Bale weights with a bale length of approx. 1.2 m 650 up to 750 kg/bale, depends on materiel Hydraulic oil tank capacity 2000 litres PLC control Siemens S7-300 Siemens TP 700 control panel Press dimensions assembled 18,000 x 4,300 x 3.270 mm (l x w x h) Press dimensions with conveyor system 18,000 x 22,000 x 5,765 mm (l x w x h) Transport weight baler approx 30 t (Main press approx. 20 t, press channel with bale clamp approx. 10 t) Kdedpfx Agjxcngns Uog Special machine equipment: Access locking by means of key transfer system Electro-hydraulic locking of the press carriage during the tying process so that the press plunger does not change position with highly expansive materials Additional optional equipment ordered: Frequency-controlled main drive, 2 x 45 kW, with up to 40 % energy savings compared to the standard motorisation 2 x 45 kW, with the same power output Manual switch-off or switch-on of the number of strapping wires to save on strapping wire for non-expansive material Cutting-edge frei rammer with 121 kN pressing force Sensory wire monitoring, with press switch-off in the event of wire breakage or wire end Bale chute Visual warning signal, mounted on the control cabinet Condition of the baler: The entire baling system (baler and conveyor belt) is in good, operational condition. Technical data for the chain belt conveyor: Manufacturer Stadler Anlagenbau GmbH Typ chain belt conveyor KF 1800 Year of construction 2012 Drive power 7.5 kW Belt speed 0.05 – 0.4 m/second Length of feeding conveyor 6,000 mm Height of side wall from feeding conveyor 400 mm Length of incline conveyor 9,000 mm Height of side wall from incline conveyor 800 mm Length of gooseneck 1,500 mm Incline 30° Nominal width 1,800 mm Useful width 1,700 mm Belt quality EP-500/4 Steel cleats on the rubber belt 50 x 50 mm Hollow pin chain, pitch 125 mm, rollers 36 mm Height of drive axle above ground 4,284 mm Overall height of conveyor belt 5,765 mm Transport dimensions of feeding conveyor approx. 7,000 x 2,200 x 1,250 mm (l x w x h) Transport dimensions of the incline conveyor 13,000 x 2,500 x 2,900 mm (l x w x h) Pit dimensions for the conveyor belt 14,765 x 3,260 x 1,250 (l x w x h) Scope of delivery: The conveyor belt, baling press with bale chute, and wire drawing stations are available for sale, but without the wire. Comments: The documentation (Manual, CE-declaration, electr./hydr.-drawings), are completely available. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors.

Condition: reconditioned (used), Year of construction: 2014, operating hours: 24,967 h, functionality: fully functional, machine/vehicle number: 004283-0030, pressing force: 122 t, filling opening width: 1,100 mm, filling opening length: 1,600 mm, bale width: 1,100 mm, bale height: 1,100 mm, warranty duration: 24 months, year of last overhaul: 2026, Equipment: documentation/manual, Sold by Bollegraaf Recycling Solutions, the original manufacturer of this Bollegraaf baler. This is a baler HBC120s (90kW) with crosswires. At the time of writing this baler is being completely refurbished in our refurbishment workshop. Kdsdpfx Aexcir Ejg Uog This refurbishment takes place on the basis of the very strict Bollegraaf OEM Refurbishment Guidelines. After refurbishment, this baler is sold with a 2-year warranty.

Condition: good (used), Technical specifications: Briquetting press in good condition Year of manufacture: 2007 Technically inspected in 06 / 2025 Cylindrical briquette: 80 mm Throughput up to max. 150 kg/h Kjdewtdk Tspfx Ag Usdg *only approx. 3,949 operating hours - Hydraulic press: briquetting press with discharge chute - Hydraulic unit: 4 kW - Pressure: max. 300 bar - Transport dimensions: 1585/2140/H1940 mm - Weight: 1,370 kg Functional guarantee upon handover We are happy to arrange a free test run!

Condition: excellent (used), Year of construction: 2004, operating hours: 34,480 h, functionality: fully functional, pressing force: 100 t, filling opening width: 1,100 mm, filling opening length: 1,600 mm, bale width: 1,100 mm, bale height: 720 mm, bale weight: 750 kg, overall weight: 19,000 kg, transport height: 3,300 mm, oil tank capacity: 750 l, power: 45 kW (61.18 HP), Technical data baler: Manufacturer Bollegraaf Typ HBK 100 Kdodpfx Agoxbgnhj Uog Year of construction 2004 Hours of operation 34,480 hours Press power main press 100 tons Press power of pre-press max. 42 tons Feed channel 1,600 x 1,100 mm Filling volume 3.15 m³ Theoretic cycle time 22 sec. Theoretic throughput capacity up to 450 m³/hour Bale size 1,100 x 720 mm, lenght variable Driving motor 45 kW Connected load 60 kW Tying system 5-fold vertical, fully automatic Throughput rate at a bulk weight of 30 kg/cbm approx. 13 tons/hour bulk weight of 50 kg/cbm approx. 20 tons/hour bulk weight of 100 kg/cbm approx. 30 tons/hour Throughput rate with ruffler approx. 20 tons/hour Bale weight 550 up to 750 kg, depends on material Volume hydraulic oil tank 750 l SPS controller Telemecanique TSX Micro Transport dimensions only baler 10,900 x 2,320 x 3,300 mm (l x w x h) Machine weight baler approx. 19 tons Comments: Unlike the standard HBC press series from Bollegraaf, this machine does not have a pre-press flap but cuts the material between blades on the press ram and the counter blade in the frame. This makes it a cutting edge press, similar to a Paal, unoTech, etc. The press is in very good condition for its age, as it was used exclusively for compressing paper from document destruction. The documentation (Manual, CE, electr./hydr.-drawings), are completely available. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors.