Condition: excellent (used), Year of construction: 2004, operating hours: 34,480 h, functionality: fully functional, pressing force: 100 t, filling opening width: 1,100 mm, filling opening length: 1,600 mm, bale width: 1,100 mm, bale height: 720 mm, bale weight: 750 kg, overall weight: 19,000 kg, transport height: 3,300 mm, oil tank capacity: 750 l, power: 45 kW (61.18 HP), Technical data baler: Manufacturer Bollegraaf Typ HBK 100 Year of construction 2004 Hours of operation 34,480 hours Press power main press 100 tons Press power of pre-press max. 42 tons Ksdpfx Agjxbgnhe Usdg Feed channel 1,600 x 1,100 mm Filling volume 3.15 m³ Theoretic cycle time 22 sec. Theoretic throughput capacity up to 450 m³/hour Bale size 1,100 x 720 mm, lenght variable Driving motor 45 kW Connected load 60 kW Tying system 5-fold vertical, fully automatic Throughput rate at a bulk weight of 30 kg/cbm approx. 13 tons/hour bulk weight of 50 kg/cbm approx. 20 tons/hour bulk weight of 100 kg/cbm approx. 30 tons/hour Throughput rate with ruffler approx. 20 tons/hour Bale weight 550 up to 750 kg, depends on material Volume hydraulic oil tank 750 l SPS controller Telemecanique TSX Micro Transport dimensions only baler 10,900 x 2,320 x 3,300 mm (l x w x h) Machine weight baler approx. 19 tons Comments: Unlike the standard HBC press series from Bollegraaf, this machine does not have a pre-press flap but cuts the material between blades on the press ram and the counter blade in the frame. This makes it a cutting edge press, similar to a Paal, unoTech, etc. The press is in very good condition for its age, as it was used exclusively for compressing paper from document destruction. The documentation (Manual, CE, electr./hydr.-drawings), are completely available. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors.

Year of construction: 2008, operating hours: 40,000 h, condition: good (used), machine/vehicle number: HBC 140 2x75kW 2008 (00191), Sold by Bollegraaf Recycling Solutions, the original manufacturer of this Bollegraaf baler and conveyor: Bollegraaf HBC140s Baler (2x75kW). Baler: Weight: 47.100 kg Construction year: 2008 Hardox bottom floor plate only Variable channel pressure control Plastic valve Hydraulic pump driven by frequency inverter Anti-rat cabling Oil in-depth filtration Modem Hours 40.000 This baler can also be sold fully refurbished according to the 'Bollegraaf OEM Certified Refurbishment standards'. This includes 2 year guarrantee. Contact us for more information or a quotation. General principles of refurbishment Cleaning & disassembly Before the actual refurbishment takes place the baler is completely cleaned and disassembled in our refurbishment workshop. Tolerances Kdjdekcgf Hjpfx Ag Ujg After the disassembly the tolerances of all steel components are measured and re-welded where necessary, this at least applies to the following components; • Ram, • Frame, • Channel, • Pre-press-flap After disassembly and inspection the ram is welded-up again and fitted with new ram wheels. The protective grids and the pre-press flap are made dent-free and repaired where necessary. Repainted After measuring the tolerances and any repair- and welding work, all components are being blasted and coated again. Hydraulics: The hydraulic tank is cleaned. The hydraulic lines & hoses are replaced. The hydraulic components are repackaged. The hydraulic oil is replaced. Cabling: All cabling is checked and replaced if necessary. All junction boxes are replaced and placed back in easily accessible positions. Wear parts: All wearing parts are replaced. The pins and shafts of the cylinders and the channel are replaced with new ones. All wearing parts of (both) needle installations and knotters are replaced for new. Cylinders: The cylinders are repackaged and, if necessary, provided with a new chrome layer or a new cylinder rod. MCC Cabinet The switch box is checked and cleaned. If necessary, electronic components are replaced with new ones. The PLC and HMI (human interface) are replaced with the latest Schneider M340 version including the latest software.

Year of construction: 2003, operating hours: 43,000 h, condition: repair required (used), machine/vehicle number: HBC 140 2x75kW 2003 (W230-005), Sold by Bollegraaf Recycling Solutions, the original manufacturer of this Bollegraaf baler and conveyor: Bollegraaf HBC140s Baler (2x75kW). Baler: Weight: 47.100 kg Construction year: 2003 Hardox bottom floor plate only Plastic valve Anti-rat cabling Hours 43.000 Kdodpfokcgynex Ag Uog This baler can also be sold fully refurbished according to the 'Bollegraaf OEM Certified Refurbishment standards'. This includes 2 year guarrantee. Contact us for more information or a quotation. General principles of refurbishment Cleaning & disassembly Before the actual refurbishment takes place the baler is completely cleaned and disassembled in our refurbishment workshop. Tolerances After the disassembly the tolerances of all steel components are measured and re-welded where necessary, this at least applies to the following components; • Ram, • Frame, • Channel, • Pre-press-flap After disassembly and inspection the ram is welded-up again and fitted with new ram wheels. The protective grids and the pre-press flap are made dent-free and repaired where necessary. Repainted After measuring the tolerances and any repair- and welding work, all components are being blasted and coated again. Hydraulics: The hydraulic tank is cleaned. The hydraulic lines & hoses are replaced. The hydraulic components are repackaged. The hydraulic oil is replaced. Cabling: All cabling is checked and replaced if necessary. All junction boxes are replaced and placed back in easily accessible positions. Wear parts: All wearing parts are replaced. The pins and shafts of the cylinders and the channel are replaced with new ones. All wearing parts of (both) needle installations and knotters are replaced for new. Cylinders: The cylinders are repackaged and, if necessary, provided with a new chrome layer or a new cylinder rod. MCC Cabinet The switch box is checked and cleaned. If necessary, electronic components are replaced with new ones. The PLC and HMI (human interface) are replaced with the latest Schneider M340 version including the latest software.

Condition: excellent (used), Year of construction: 2019, HSM V Press 1160 plus Kedpol Uvukjfx Ag Uodg Pressing force 532 kN, opening width 1,195 m, opening height 0.65 m, drive power 4 kW, press type BP, dead weight 2.43 t, transport length 1.78 m, transport width 1.568 m, transport height 2.995 m, press type baler. Press immediately ready for use.

Condition: good (used), Technical data: Briquetting press RUF RB 440 Press capacity when pressing wood: up to a maximum of 440 kg/hour Kodpfx Agjt H D Eze Usdg Material moisture: maximum 15 % Motor power: approx. 30 kW Briquette size; rectangular: 150 x 60 mm Length: 40 - 110 mm Dimensions approx. 1680 x 1800 x 2000 mm Weight: 3000 kg

Condition: reconditioned (used), Year of construction: 2011, functionality: fully functional, Wet waste press press container Bergmann MPB405 SN/10 for skip loader 10cbm usable volume tested, serviced, fully functional Painting in desired RAL color possible We would be happy to make you an offer including delivery. Kdedpfxsxql Dgs Ag Ueg

Condition: refurbished (used), Year of construction: 1999, functionality: fully functional, pressing force: 71 t, filling opening width: 1,080 mm, filling opening length: 1,620 mm, bale width: 1,100 mm, bale height: 720 mm, bale weight: 600 kg, total width: 3,450 mm, total height: 4,090 mm, total length: 10,020 mm, input voltage: 400 V, overall weight: 27,000 kg, noise level: 85 dB, pressure: 300 bar, transport height: 2,300 mm, power: 37 kW (50.31 HP), Fully automatic channel baler with pre-press flap available immediately. The machine includes a conveyor belt with a floor-mounted section. The baler is supplied in refurbished condition and the conveyor belt underwent a belt overhaul at the beginning of this year. The machine was taken out of production at the beginning of October and is currently stored in our facility. It can be demonstrated in operation at our location. This machine is particularly suitable for baling paper/cardboard and various types of plastics such as PET, HDPE, and big bags. Technical specifications baler: Drive: 37 kW Press force: 71 tons Bale dimensions: 1100 x 720 x 1300 mm (length adjustable) Number of wires: 4 vertical Filling hopper dimensions: 1620 x 1080 mm Bale weight: up to 600 kg (depending on material) Capacity: up to 20 tons per hour (depending on material) Transport weight: 27,000 kg Kdjdoxl Rqbjpfx Ag Usg Technical specifications conveyor belt: Length of horizontal section: 3,000 mm Length of inclined section: 7,424 mm Angle: 29° Filling option: at floor level

Condition: used, Year of construction: 2006, functionality: fully functional, Paper/Waste Baler JONGEJANS model: DBF145_00_h00004 Kdjdpfx Agsxk N Dwe Uog Number of filters: 84 Needlefelt polyester Filter surface area: 145 m² Installed components: Briquette press CS3-12 Cleaning fans 1.5 kW

Condition: good (used), Year of construction: 2011, operating hours: 1,866 h, Manufacturer: Husmann Typ: SPB 20 SEL-E Volume: 20m3 Build in: 2011 Kdodpfow Uz Haox Ag Ueg Backdoor: top hingend

Condition: like new (used), UNDER CONSTRUCTION We are currently in the final stages of a complete overhaul of a fully automatic stationary press. This stationary press is including 2 containers 30m3 equipped with side door Build in: RV 2025 Overhaul work we have carried out: -new floor -new side panel Kdodpfx Ajw Uc T Uog Uog -new guide blocks and guide plates - pressblock overhauled -cylinders fitted with new sleeves -new fork pins -new return filter -new hydraulic hoses -oil renewed

Condition: used, Year of construction: 2015, operating hours: 1,661 h, Manufacturer: Husmann Typ: SPB 20 SEL-E Volume: 20m3 Build in: 2015 Ksdjwca Aqepfx Ag Uodg Backdoor: bovenscharnierend

Condition: good (used), Year of construction: 2009, power: 7.5 kW (10.20 HP), input voltage: 220 V, Husmann static press incl. funnel and container Kdedpfxewmm T Dj Ag Ueg Manufacturer: Husmann Typ: ST-SEL-TS-V Build in: 2009 Weight: 5150 kg Engine: 7,5 kw Volume container: 32m3 Door for unloading: side hingend

Condition: good (used), Year of construction: 2008, Manufacturer: Presto Kdsdotq Ehgopfx Ag Usg Type: SPN15 Build in: 2008 Backdoor: side hinged Lifting system: hook The container and funnel were recently painted in RAL 7016

Condition: good (used), Year of construction: 2009, Manufacturer: AJK Typ: 10W Build in: 2009 Volume: 10m3 Weight: 4060 kg Ksdpfjw Sm H Tsx Ag Uodg Backdoor: top hingend

Condition: reconditioned (used), Year of construction: 2015, operating hours: 28,748 h, functionality: fully functional, pressing force: 60 t, filling opening width: 1,100 mm, filling opening length: 1,500 mm, bale width: 1,100 mm, bale height: 750 mm, bale weight: 570 kg, overall weight: 20,000 kg, oil tank capacity: 600 l, power: 37 kW (50.31 HP), volume flow: 350 m³/h, Technical data baler: Manufacturer Presona AB, Sweden Type LP 60 VH1 Year of construction 2015 Total operating hours, 30,143 hours, as of July 2025 Effective pump running time onl 6,527 hours, as of July 2025 Number of pressed bales 115,193 bales, as of July 2025 Press force pre press 25 t Main press force 60 tonnes Specific pressing force 73N/cm² Dimensions of feed chute 1,500 x 1,100 mm Filling volume / pressing cycle 2.7 m³ Theoretical throughput capacity 800 m³/hour Throughput capacity under operating conditions 350 m³/hour Bale dimensions 1,100 x 750 mm Drive power 37 kW Tying 5-fold vertical, fully automatic Throughput capacity with a Kdsdpfxjvn Tg Ij Ag Uog Bulk weight of 50 kg/cbm 11 to 14 tonnes/hour Bale weights 420 to 570 kg, depending on material Hydraulic oil tank volume 600 litres Baler dimensions assembled with hopper 10,100 x 3,750 x 4,310 mm (l x w x h) Transport dimensions excluding press 10,100 x 2,400 x 3,000 mm (l x w x h) Machine weight press approx. 20 tonnes Condition of the press: The press was partially overhauled in our workshop and then tested in manual and automatic mode. The following overhaul work was carried out: Machine cleaned, partially derusted and partially repainted Hydraulic oil tank emptied and cleaned Oil filter and air filter replaced, new hydraulic oil filled Press ram dismantled and cleaned All four rollers removed from the press ram and replaced Grease cartridges of the automatic roller lubrication system replaced Slide rails cut out from the press floor in the press room Underbody reinforced with welded sheets New HARDOX slide rails welded in Wire station with deflection rollers for the lower wire cleaned and made operational Slide rails cut out from the floor in the press channel New HARDOX slide rails welded in Both side walls of the press channel dismantled, derusted Worn side wall plates cut out Complete side walls covered with new wear plates and welded Main hydraulic cylinder dismantled and disassembled for inspection Piston rod replaced, cylinder tube honed Complete seal set replaced, pressure test carried out Vertical needle system for binding dismantled, cleaned, wire deflection rollers made functional and serviced Chain cleaned, greased, chain tension readjusted Drillomat cleaned, wire knife, drill shafts and drill fingers checked, retightened with torque and serviced Machine checked, general maintenance work carried out and press tested in manual and automatic mode Comments: The press is sold without a conveyor belt and without wire stations. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors.

Condition: reconditioned (used), Year of construction: 2012, operating hours: 25,895 h, functionality: fully functional, pressing force: 78 t, filling opening width: 1,100 mm, filling opening length: 1,500 mm, bale width: 1,100 mm, bale height: 750 mm, bale weight: 600 kg, overall weight: 24,000 kg, oil tank capacity: 1,000 l, power: 55 kW (74.78 HP), volume flow: 930 m³/h, Technical data baler: Manufacturer Presona AB Typ LP 80 VHK 1 Year of construction 2012 Total machine operating hours 25,895 hours, as of July 2025 Pump operating hours, effective 14,135 hours, as of July 2025 Number of bales pressed 235,597 pieces, as of July 2025 Press power main press 78,5 tons Specific press capacity 95 N/cm² Press power of pre-press 28 tons Volume of pressing chamber 2,7 m³ Kdodpovwlqqefx Ag Usg Feed channel1,500 x 1,100 mm Theoretic throughput rate 930 m³/h Throughput rate under operating conditions 410 m³/h Bale size 750 x 1,100 mm Driving motor 55 kW Tying system 5 fold vertical, 3-fold horizontal, full automatic Throughput rate with a bulk density of 30 kg/m³ approx. 9 to 12 tonnes/hour, depending on material 50 kg/m³ approx. 14 to 17 tonnes/hour, depending on material 100 kg/m³ approx. 16 to 25 tonnes/hour, depending on material Throughput capacity with MSW (Municipal Solid Waste) approx. 20 to 27 tonnes/hour, depending on material Bale weight 450 up to 600 kg, depends on material and bale length Volume hydraulic oil tank 1,000 l Baler dimensions built up with hopper 10,985 x 3,750 x 4,310 mm (l x w x h) Transport dimensions only baler 10,985 x 2,300 x 2,900 mm (L x w x h) Machine weight baler approx. 24 tons Condition of the press: The machine was partially overhauled and serviced in our workshop and, once the work was complete, tested in manual and automatic mode during operation. The following overhaul work was carried out: Machine cleaned, partially derusted and partially repainted Hydraulic oil tank emptied and cleaned Oil filter and air filter replaced, new hydraulic oil filled Press ram dismantled and cleaned All four rollers removed from the press ram and replaced Wire station with deflection rollers for the lower wire cleaned and made operational Side guides removed from the press ram, smoothed, mounted and readjusted Main hydraulic cylinder dismantled and disassembled for inspection Piston rod replaced, cylinder tube honed Complete seal set replaced, pressure test carried out Vertical and horizontal needle system for binding dismantled, cleaned, wire deflection rollers made functional and serviced Chain cleaned, greased, chain tension readjusted Drillomat cleaned, wire knife, drill shafts and drill fingers checked, retightened with torque and serviced Door contact switch checked and partially replaced. Emergency stop switch checked. Complete electrical wiring checked and partially replaced. Bearings of the wire guide rollers under the press replaced. New safety grilles for vertical and horizontal binding manufactured and installed. Machine checked, general maintenance work carried out and press tested in manual and automatic mode Scope of delivery: Only the baler will be sold. Comments: The documentation (Manual, CE-declaration, electr./hydr.-drawings), are completely available. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors.

Condition: reconditioned (used), Year of construction: 2005, operating hours: 30,408 h, functionality: fully functional, pressing force: 50 t, filling opening width: 1,100 mm, filling opening length: 1,250 mm, bale width: 1,100 mm, bale height: 720 mm, bale weight: 550 kg, overall weight: 16,000 kg, oil tank capacity: 600 l, year of last overhaul: 2024, Technical data baler: Manufacturer Presona AB Type LP 50 EH1 Year of construction 2005 Operating hours 30,408 hours, as of April Number of pressed bales 198,059 as of April Pressing force main press 50 tonnes Specific pressing force 63 N/cm² Theoretical throughput capacity 530 m³/hour Throughput capacity under operating conditions 260 m³/hour Dimensions of feed chute 1,250 x 1,100 mm Bale chamber volume 2.2 m³ Bale dimensions 1,100 x 720 mm, variable length Drive power 22 kW Tying 5-fold vertical, fully automatic Throughput rates with a bulk density of 30 kg/cbm 6 up to 7 tonnes/hour Bulk weight of 50 kg/cbm 7 up to 9 tonnes/hour Bulk weight of 100 kg/cbm 11 up to 14 tonnes/hour Bale density (paper/newspapers) 400 to 550 kg/m³ Kdsdpfx Ageu Thhre Ujg Hydraulic oil tank capacity 600 litres PLC control Telemecanique TSX Micro Schneider Magelis control panel Effective transport dimensions excl. baler 8,125 x 2,300 x 3,000 mm (L x W x H) Transport weight press approx. 16 tonnes Condition of the baler: The machine was partial overhauled in our workshop and general maintenance work was carried out. After completion of the overhaul work, the press was tested during operation and is available for sale at short notice. The following overhaul work was carried out: General work: Machine cleaned, derusted, primed, partially painted Wire entry marks in the press channel feed-throughs welded shut and smoothed Hydraulic unit: Hydraulic oil tank emptied, tank cleaned, new oil filled Oil filter and air filter replaced Leaky oil sight glass on hydraulic oil tank replaced All hydraulic hoses replaced Electrics: English language installed in the programme menu Two key switches in the control panel replaced Control cabinet replaced Signal lamp on the control cabinet replaced Flaps end switch replaced Electrical system of the turbulator replaced, connected and tested Press ram: All four rollers removed from the press ram and replaced Main hydraulic cylinder dismantled, disassembled and partially overhauled, cylinder tube honed, complete seal set replaced, leak test performed All plastic wear pads on the press ram replaced Pre-press: Both bearings on the pre-press shaft replaced. Both hydraulic cylinders dismantled, disassembled and partially overhauled, both cylinder tubes honed, complete seal sets replaced, leak test performed. Scraper flap on the pre-press replaced. Binding system: Two complete needles with wire deflection rollers replaced Needles adjusted and set All wire deflection rollers in the needle heads replaced Drill fingers replaced Two drill shafts replaced All 8 wear plates on the Drillomat, under the drill fingers, replaced Scope of delivery: Only the baler will be sold. The documentation (Manual, CE-declaration, electr./hydr.-drawings), are completely available. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors.

Condition: good (used), Year of construction: 2007, Baler STRAUTMANN PP1208, year of manufacture 2007 Ksdpexwc Nyofx Ag Ujdg

Condition: good (used), Year of construction: 2015, Year of manufacture 2015, serial number 413.00.032, pressing force 600 kN Ksdpfoxwc Naex Ag Ujdg

Condition: reconditioned (used), Year of construction: 1999, functionality: fully functional, type of input current: three-phase, power: 160 kW (217.54 HP), input voltage: 380 V, warranty duration: 12 months, year of last overhaul: 2023, Equipment: documentation/manual, 1 pellet press make: Buhler DPAB inner diameter die 660 mm tread die 138 mm Press is equipped with 1 motor 160 KW . Kedpfx Aerah Evjg Uedg Press door is made of Stainless steel with overload valve in door. 2 Roll press with 2 rolls on the press overhauled in dimple or racked version Press is complete with die lifting device and tools The press is completely overhauled and equipped with new bearings and wear parts such as front and rear sliders die washer etc. Also new V-belts Also, all safety devices will be observed and appropriate switches on Friction protection , door switch and inspection hatches will be fitted.

Condition: reconditioned (used), functionality: fully functional, machine/vehicle number: Pal 1600, power: 180 kW (244.73 HP), input voltage: 380 V, warranty duration: 12 months, Equipment: documentation/manual, 1 pellet press brand: Paladin 1600-210 inner diameter die 850 mm tread die 210 mm Press is equipped with 2 motors each 90 KW n=1500. Press door is made of stainless steel with overload valve in door. 3 Roll press with 3 rolls on the press overhauled in a drilled or racked version Press is complete with mold lifting device and tools The press is completely overhauled and equipped with new bearings and wear parts such as front and rear sliders die washer etc. Also new V-belts and toothed belt. Also, all safeties will be observed and appropriate switches on Friction safety , door switch and inspection hatches will be fitted. Refurbished pump unit for friction and V-belt tensioning Kodoq U R N Tspfx Ag Usdg Remark: Conditioner on the press is optional

Condition: used, Year of construction: 2007, functionality: fully functional, total width: 9,000 mm, total length: 8,000 mm, total height: 5,000 mm, pressing force: 384 t, power: 210 kW (285.52 HP), overall weight: 82,000 kg, bale height: 400 mm, bale width: 400 mm, Scrap Baling Press Technical Data - Manufacturer: RS Maschinenbau - Model: BP-III-4040 Li - Year of manufacture: 2007 - Bale size: 400×400 mm - Pressing force CST3: 3,770 kN - Pressing force CST2: 2,886 kN - Pressing force CST1: 2,120 kN - Steel throughput: 20–24 t/h - Aluminium throughput: 10 t/h - Drive power: 210 kW - Footprint: 9 × 8 × 5 m Kdodpfxjx A U Uxj Ag Usg - Machine weight: approx. 82 t Location: Germany Price ready for operation, FCA location: on request Price FCA – ATM overhauled: (blank) Available from: August 2026

Condition: excellent (used), Year of construction: 1996, pressing force: 30 t, input voltage: 380 V, bale weight: 600 kg, type of input current: AC, overall weight: 3,000 kg, Manufacture: Philadelphia Tramrail Model: HT30036 Vintage: 1996 400V/45A, 3 phases, 15kW 180 bar system pressure 206 bar maximum system pressure Made of heavy-duty structural steel Average cycle time of 53 seconds Dimensions: 1980 x 1050 x 3860mm Kdjdpfx Agsm Amk Nj Uog Advance height: 1400mm Baling chamber: 1600 x 760

Condition: excellent (used), Year of construction: 2002, functionality: fully functional, pressing force: 15 t, bale width: 700 mm, bale height: 700 mm, bale weight: 220 kg, input voltage: 400 V, power: 4 kW (5.44 HP), empty load weight: 2,700 kg, Manufacturer: Borg Baling Company Type: S-15KK Year of production: 2002 3x400V, 4kW, 14.5A Compression force: 15t Net weight: 2.7 t Bale max. sizes Kedpfxjh Dy Rfe Ag Uedg 700x700x1000 mm weight of a bale: ca 120 – 220kg Wide Range of Used Machinery, Industrial Equipment

Condition: not inspected (used), Year of construction: 1985, functionality: fully functional, pressing force: 50 t, bale length: 1,000 mm, bale width: 750 mm, bale height: 750,750,750 mm, bale weight: 500 kg, input voltage: 400 V, overall weight: 7,500 kg, oil tank capacity: 500 l, power: 30 kW (40.79 HP), empty load weight: 7,500 kg, input frequency: 50 Hz, Manufacturer: Paal Typ: Pacomat V Year of construction: 1985 Press power main press: 50 t Specific press capacity: 5 kg/cm² Feed channel: 1.000 x 720mm (l x w) Kdjdoic Rl Djpfx Ag Usg Theoretic throughput rate: 200 cbm/h Bale size: 700 x 1.000 mm (w x h) length adjustable Driving motor: 30 kW Bale weight: approx. 500 kg Machine weight: approx. 8t The hydraulic unit is functional, the drive motor is in the removed state.