Used bale presses for sale (215)

Condition: reconditioned (used), Year of construction: 2002, operating hours: 44,590 h, functionality: fully functional, pressing force: 200 t, filling opening width: 1,020 mm, filling opening length: 2,000 mm, bale width: 1,100 mm, bale height: 1,100 mm, oil tank capacity: 3,100 l, power: 150 kW (203.94 HP), year of last overhaul: 2025, Technical data baler: Manufacturer MACPRESSE EUROPA S.R.L. Typ 112 Year of construction 2002, partially refurbished in December 2025 Operating hours 44,590 hours, stand December 2025 Press power main press 200 tons Specific press capacity 16,5 kg/cm² Feed channel 2,000 x 1,020 mm Filling volume 2,65 cm³ Theoretic throughput rate 795 m³/h Bale size 1,100 x 1,100 mm, length variable Driving motor 2 x 75 kW Tying system 5-fold horizontal, full automatic Throughput rate at MSW approx. 48 up to 54 tons/h, depends on material Volume hydraulic oil tank 3,100 l Machine weight baler approx. 50,8 tons Scope of delifery: Chedpfxsx Dnb Ue Abbsf 1 piece baler MACPRESSE, type 111A 1 operating manual with CE declaration, electrical and hydraulic circuit diagram Comments: The machine was serviced and partially overhauled in our workshop. The following work was carried out and parts replaced: • Hydraulic oil tank emptied and cleaned • Oil and air filters replaced • New hydraulic oil filled • All hydraulic hoses replaced • Press ram dismantled, broken down into individual parts, mechanics made operational • Front two main rollers replaced • Knives on the press ram replaced • Main hydraulic cylinder dismantled, disassembled, cylinder tube and piston rod checked, complete seal set replaced • Counter knife in the frame replaced • Knife gap adjusted to approx. 3 mm • Upper steel guide rails in the frame on the left and right replaced. • Worn press base cut out, base plate replaced with wear-resistant HARDOX steel. • Binding and twisting unit dismantled, broken down into individual parts, mechanics made functional, all twisting shafts and ball bearings replaced. • All wire rollers in the needle heads replaced • Wire knives cleaned and readjusted, chains greased and tensioned • All wire deflection rollers made operational • All door contact switches replaced • Wirbulator device dismantled, disassembled and made operational • General maintenance work carried out Finally, the press was subjected to a machine test in manual and automatic mode, see video for the machine function test. The documentation (BA, CE, electrical/hydraulic circuit diagram) is complete. Viewing is possible by appointment. We accept no liability for the technical specifications or any errors.

Condition: used, Year of construction: 1983, total width: 750 mm, total height: 900 mm, total length: 2,400 mm, Empty weight: 500 kg - Year: 1983 Chjdpoxalyyefx Abbsf - Documentation available: No - CE certificate present: No - Transport dimensions: 2400mm x 750mm x 900mm (l x w x h) - Transport weight [kg]: 500kg - Transport packages [pcs.]: 1 Financial information VAT: The price shown is exclusive of VAT VAT/margin: VAT deductible for entrepreneurs Delivery and trade-in always possible for everything in the industrial sectors Yorick Diebels

Condition: good (used), Year of construction: 2016, functionality: fully functional, Baler Avermann, Model AVOS 1410 BR5 – 45/80, Pressing Force 80 t, Year of Manufacture 2016 Technical Specifications: Manufacturer: Avermann Maschinenfabrik Model: AVOS 1410 BR5 – 45/80 Year of manufacture: 2016 Pressing force: 80 t Drive power: 45 kW Feed opening: 1,400 x 1,000 mm Throughput at 35 kg/m³: 6.0 t/h Throughput at 60 kg/m³: 10.5 t/h Throughput at 100 kg/m³: 17.5 t/h Bale dimensions: 1,100 x 750 mm (W x H), length variable Bale weight: up to 600 kg, depending on material Tying: 5-fold vertical, automatic Machine dimensions: approx. 10,850 x 2,400 x 3,800 mm (L x W x H) Machine weight: approx. 18,000 kg Remarks: The press is still in operation and can be inspected upon request. It is expected to be available from February 2026. A suitable WESTERIA conveyor belt is optionally available. The main cylinder was replaced in November 2025. Additional images available upon request. Please feel free to contact us. Chsdpsx Dkkxefx Abbjf Please note: All technical data are based on manufacturer’s information. We do not accept liability for any errors or omissions in the provided specifications. This offer is non-binding, subject to prior sale, and may be withdrawn at any time. Inspections are available by appointment. Sale is ex works, prepaid, without guarantee or warranty.

Condition: ready for operation (used), Year of construction: 2012, Brand: DIXI Chjdpfxex Af Ntj Abbsf Model: 60 Sh Year of manufacture: 2012 Pressing force: 60 tons Voltage: 400V Maximum bale weight: 340-500 kg Bale dimensions: approx. 120 x 80 x 80-110 cm Machine weight: 2,400 kg Machine dimensions: 190 cm wide x 140 cm deep x 230 cm high Filling opening dimensions: 115 cm x 80 cm deep x 55 cm high Condition: Very good! Functionality checked. FLITS Rental & Sales service: With every machine, we supply a bundle of binding wire (120 wires). Need more bundles of binding wire? Request a quote with no obligation. FLITS Rental & Sales is your reliable partner for the sale and rental of high-quality machines for both businesses and private individuals. We focus on delivering efficient solutions in the areas of internal transportation, cleaning, waste processing, and working at height. At FLITS Rental & Sales, you will find a wide range of machines suitable for deployment in various sectors. See our advertisements for: waste balers for efficient waste management, electric pallet trucks/stackers for fast and safe internal transport, scrubbers for thorough and professional floor cleaning, forklifts in various designs suitable for different working environments. With FLITS Rental & Sales, you choose speed, clarity, and reliability. We think along with you, respond immediately, and ensure that you quickly have the right machine at your disposal. Visit our location You are very welcome to view the machines at our premises. We are located at: Schoterlandseweg 94, 8413NE Oudehorne, Netherlands. Visits are possible by appointment, so we can take the time to inform you thoroughly and show you the right machines. Contact Do you have questions or would you like to receive a no-obligation quote? Please feel free to contact us: We are happy to help you further. Waste baler Paper baler Cardboard baler Plastic baler Waste compactor Recycling Textile baler Waste Waste processing DIXI

Condition: like new (used), Year of construction: 2022, operating hours: 6,000 h, machine/vehicle number: 006424, pressing force: 100 t, filling opening width: 1,100 mm, filling opening length: 1,600 mm, bale width: 1,100 mm, bale height: 720 mm, warranty duration: 3 months, power: 75 kW (101.97 HP), Equipment: documentation/manual, This very young baler is sold by Bollegraaf Recycling Solutions. This is a HBC100 (75kW) baler featuring cross wires, FULL HARDOX, and a Bollegraaf chain conveyor with Bordoflex. Both the chain conveyor and the baler are equipped with all possible options for maximum efficiency in baling all types of plastics. Codpfxsxvh Ewo Abbshf Both units were built in 2022 and have very few operating hours. The previous owner purchased a new Bollegraaf system and traded in the machines in question. After disassembly, this baler is sold with a 3-month warranty. HBC100K Baler (75kW) 390mm supports Intermediate hopper Conveyor chute Platform with caged ladder Additional photocells Frequency controller for the main motor for energy savings APCP (adaptive self-learning channel pressure control for consistently optimal bale weights) Cross wires (3 horizontal wires and 5 vertical wires) Full Hardox lining inside the baler Bale exit Hydraulic lifting mechanism for both knotting sections for improved accessibility/maintenance Bale length display Air conditioning on the control panel Chain conveyor frequency controller Hydraulic oil heater Hydraulic unit cooler 4G modem for remote support Chain conveyor Bollegraaf HBT 1200/1800*20400 Equipped with Bordoflex for extra chain protection Dirt discharge plate Supports Chain lubrication

Condition: good (used), Welger Type: RC 660 Roller compactor with Brück suction Compact and fully automatic Used exclusively for producing pressed bales from low-density packaging materials. Application variants Press materials Paper edge trimming (strips and endless) Paper and film bags PP film edge trimming Film strips Clothing protection film (PP/PE films) PP/PE fiber material Insulating and nonwovens Foam mesh Csdpfjdtxbiox Abbehf Packaging foam Tetrapak Length 2100mm, width 940mm, height 1755mm Dimensions of filling shaft 330 mm x 600 mm Bale format max. 400 mm x 600 mm Bale weight 20 - 30 kg depending on the material being pressed Press density 250 - 400 kg/m³ depending on the material being pressed Throughput daily output 30 bales / day Feed speed 0.36 m/s RC 660 3X 400V 50Hz 16A 2.2 kW 5.0A 700 kg Brück extraction Series: KFA Size: 60-30-3000 Air output: 6,000 m³/h Motor output: 0.3 kW Filter area: 30 m² Negative pressure: 3,100 Pa Condition: used Scope of delivery: (see picture) (Changes and errors in the technical data, information is subject to change!) We will be happy to answer any further questions you may have over the phone.

Condition: reconditioned (used), Year of construction: 2009, operating hours: 22,029 h, functionality: fully functional, pressing force: 80 t, filling opening width: 1,000 mm, filling opening length: 1,400 mm, bale width: 1,100 mm, bale height: 750 mm, bale weight: 600 kg, overall weight: 16,000 kg, power: 45 kW (61.18 HP), year of last overhaul: 2025, Technical data baler: Manufacturer Avermann Maschinenfabrik GmbH & Co. KG, Germany Type AVOS 1410-45/80 Year of construction 2009 Operation hours 22,029 hours, as of December 2025 Press power main press 80kN Specific press force 103,9 N/cm² Feed channel 1,400 x 1,000 mm Theoretic cycle time 12 sec Theoretic throughput capacity 300 m³/h Bale size 1,100 x 750 (w x h), the length is variable Drive power 45 kW Connected load 75 kW Tying system 4-fold, vertical, fully automatic Throughput capacity at a bulk weight of 30 kg/cbm approx. 6,0 t/h bulk weight of 50 kg/cbm approx. 10,5 t/h bulk weight of 100 kg/cbm approx. 17,5 t/h Bale weight with a bale length of approx. 1.2 m up to 600 kg, depends on material Chedpjx A U Ncsfx Abbsf SPS controller Siemens S7-300 Operating panel pulsotronic Baler dimensions built up 8,610 x 2,400 x 3,835 mm (l x w x h) Transport weight baler approx. 16 t Special equipment: Wear-resistant floor made of HARDOX steel Special press ram for pressing ‘difficult’ materials and loose bulk materials with small grain sizes Control cabinet air conditioning Machine foot elevation 200 mm Remark: The machine was serviced and partially overhauled in our workshop. The following work was carried out and parts replaced: • Dismantling of the press ram, disassembly into individual parts, reconditioning of the mechanics, replacement of the following plastic wear plates and rails: o Plastic wear rails left/right under the press ram o Plastic wear rails left/right above the press ram o Plastic main wear plate (support plate) in the centre under the press ram • Steel guide rails on the left/right in the frame • Replacement of the entire base plate, four-piece, made of wear-resistant HARDOX steel • Wire inlet rails in the press floor newly welded and smoothed • Replacement of the counter blade, two-piece, in the frame • Adjustment of the blade gap to approx. 2.5 mm • Dismantling of the binding and twisting unit, disassembly into individual parts, loosening of the mechanics, replacement of all deep groove ball bearings and axial ball bearings on the twisting shafts, wire blades cleaned and readjusted, chains greased and tensioned • Support roller in front of the twisting shafts replaced • All hydraulic hoses replaced • Oil filter and air filter replaced • Main hydraulic cylinder checked for leaks • The hydraulic oil is only one year old, has been chemically analyzed, is still in good condition, and has therefore not been changed but can continue to be used. • General maintenance work carried out Finally, the press was subjected to a machine test in manual and automatic mode; see video for the machine function test.

Condition: excellent (used), Year of construction: 2021, operating hours: 4,975 h, functionality: fully functional, type of input current: three-phase, transport height: 1,894 mm, The Bergmann PS1400 is an intelligent compaction station, also known as a mini compactor, offering an alternative to traditional baling presses. Instead of compressing recyclable materials into bales, the PS1400-E compacts recyclables directly into a large plastic bag (approximately 1,400 liters) placed on a pallet. This system is ideal for environments with a continuous flow of recyclable material, such as distribution centers, supermarkets, or production facilities dealing with large volumes of packaging waste. As the machine utilizes a rotating compaction roller instead of an up-and-down compaction plate, the PS1400-E can process continuous streams of recyclables without having to pause for separate press cycles. You simply throw cardboard, plastic film, residual waste or other materials into the machine’s hopper. A powerful steel roller equipped with cutters grabs the material, shreds it, and compresses it down into the bag below. Continuous loading is possible – the feed opening can remain open while the roller turns, ensuring there is no waiting time. This continuous loading capability significantly increases processing speed compared to, for example, a baler (where you need to wait for the press cycle to finish and the door to reopen each time). The PS1400 is user-friendly: it features a simple start/stop button or can even operate fully automatically (on some models it starts when recyclable material is detected). Since recyclable material is neatly compacted into a sturdy PE bag, you are left with a compact “block” of recyclables on a pallet at the end. This package can be easily sealed and moved with a pallet truck or forklift. A major benefit is that the packed waste bales are clean and leak-proof, which allows you to transport them together with goods without risk of contamination. This is especially convenient in supermarkets or production facilities: the compacted waste bags can be sent back on delivery trucks, helping to avoid empty return trips. Chjdpfx Asxyq Ayobbjf With the PS1400, you not only save storage space (up to 80% reduced waste volume is achievable, depending on the material), but also labor time. Staff need to make fewer trips to the waste container, and do not have to strap or lift bales—the waste bag is only replaced when it is full, which takes much longer. The machine is safe (equipped with emergency stop and secured access) and, thanks to its electric drive, operates relatively quietly. Maintenance is minimal: the rotating compaction roller is self-cleaning and the hydraulic system is robustly engineered. In summary, the PS1400-E provides a modern, efficient way to compact recyclables directly at the source into manageable packages, delivering significant logistic and cost advantages.

Condition: good (used), Year of construction: 2002, functionality: fully functional, Vertical baler HSM VL 600, year of manufacture 2002 Technical data: Manufacturer: HSM Model: HSM VL 600 Year of manufacture: 2002 Pressing force: 60 t Drive power: 7.5 kW Cycle time (idle): 37 s Filling height: 1130 mm Filling opening: 1150 x 735 mm Bale size: 1200 x 1100 x max. 1200 mm Bale weight: 550 kg Machine weight: 3575 kg Materials: Paper, cardboard, film Note: The operating manual is available. Chsdpfx Abox A Ur Dobsf Please note: All technical data is based on manufacturer specifications. We do not accept liability for the accuracy of the information provided or for any possible errors. Offers are subject to change, prior sale reserved, and may be withdrawn at any time. Inspections are possible by appointment. Sale ex location, without warranty or guarantee. Our payment terms are 100% advance payment.

Condition: ready for operation (used), Year of construction: 2010, Brand: HSM Model: V-Press 1160 plus Chedpfx Asxy Iycjbbof Year of manufacture: 2010 Pressing force: 532 kN Voltage: 400 V Maximum bale weight: up to 550 kg (depending on material) Bale dimensions: 120 x 110 x 120 cm Machine weight: 2,403 kg Machine dimensions: 180 x 157 x 298.5 cm Filling opening dimensions: 19.5 x 65 x 111.5 cm Condition: very good! Functionality checked. FLITS Rental & Sales service: with every machine we include a bundle of baling wire (120 wires). Do you require additional bundles of baling wire? Please request a complimentary quote. At FLITS Rental & Sales, you choose speed, transparency, and reliability. We think along with you, respond immediately, and ensure you quickly receive the right machine. You are very welcome to view the machines at our premises. We are located at Schoterlandseweg 94, 8413NE Oudehorne. Visits are by appointment, so we can take the time to advise you thoroughly and present the most suitable machines. We are happy to assist you! Waste baler Paper baler Cardboard baler Plastic baler Waste compactor Recycling Textile baler Waste processing

Condition: used, Year of construction: 1997, functionality: fully functional, machine/vehicle number: 97020-0010, pressing force: 80 t, filling opening width: 1,100 mm, filling opening length: 1,600 mm, bale width: 1,100 mm, bale height: 720 mm, power: 45 kW (61.18 HP), operating pressure: 250 bar, Equipment: documentation/manual, This baler is sold by Bollegraaf Recycling Solutions. This is a HBC80 baler (45kW) with cross wires and a chain conveyor. Bale press built: 1997 Chain conveyor built: 2015 Baler Bollegraaf HBC80 45 kW Chjdsxvh Dyepfx Abbof Bale dimensions: 1100 x 720 mm 45 kW main motor Intermediate hopper Conveyor chute Control cabinet Schneider PLC Chain conveyor Horizontal floor section: 6000 mm Rise section: 12500 mm (30 degrees) Gooseneck This baler can be inspected in operation until the end of March.

Condition: good (used), Waste compactor, waste compactor, compactor container, waste container, self-compacting container, waste compactor, paper compactor container, paper container, cabinet compactor, vertical baler -Manufacturer: DIXI, Cabinet baler, vertical baler -Type: 15 S -Drive power: 4 kW -Pressure pressure: t -Interior dimensions 1100x690x1370 mm -Transport dimensions: 1540/950/H1970 mm Cedpsxwuilofx Abbohf -Weight: 834 kg

Year of construction: 2001, condition: good (used), HSM-500.1_VL PRESS PAPER PRESS FILM PRESS BALER Chodpfx Aolc Du Nebbjf ready to use good CONDITION used & good / see photos model: HSM 500.1 VL machine no. 6135.244.P serial no. 220109689 pressing pressure 50 tons V 400; Hz 50 KW 7,5 Amp. 15,5 Pressing force 6 tons Year of manufacture 2001 more presses in our other offers article used and good / roughly cleaned (plug in and go ) dimensions: on request !!! Other photos are for further use possibility. All items seen in photos also available from us. Price quotation net per piece for pickup from stock 47441 Moers current stock 1 piece Viewing is expressly offered. more technology in stock see photos or ask by phone General: We offer here from various acquisitions articles, which we describe as well as possible, as well as set meaningful photos. Further details about the article can not be made. We offer the possibility of Tuesday and Thursday in the time between 9 and 16 o'clock after telephone appointment to visit. If necessary, the article can be taken away immediately. Answers to this article we can offer due to time constraints only if you provide us with a phone number when you request. This offer, unless specifically described, is USED GOODS. Any packaging may be damaged. Items have been visually inspected and are as far as technically ok. All offers ex stock 47441 Moers. If you want shipping, please contact us to discuss packaging and shipping costs. Call with interest gladly by. all dimensions are approximate Errors in the description expressly reserved.

Condition: excellent (used), Year of construction: 2017, operating hours: 19,187 h, functionality: fully functional, pressing force: 140 t, filling opening width: 1,100 mm, filling opening length: 1,600 mm, bale width: 1,100 mm, bale height: 1,100 mm, bale weight: 1,500 kg, overall weight: 52,000 kg, Technical data baler: Manufacturer Bollegraaf Recycling Machinery B.V. Typ HBC 140 Year of construction 2017 Working hours 19,187 hours, stand October 2025 Codpfxsxrta Eo Abbshf Press power main press 140 tons (max. 153,5 tons) Press power of pre-press 70 tons Feed channel 1,600 x 1,100 mm Capacity per cycle time 4,34 m³ Theoretic cycle time 16 sec. Bale size 1,100 x 1,100 mm Driving motor 2 x 75 kW Connected load 226 kW Full load current 428 A Tying system 5-fold vertical, fully automated Throughput rate at a bulk weight of 30 kg/cbm approx. 30 tons/h bulk weight of 50 kg/cbm approx. 46 tons/h bulk weight of 100 kg/cbm approx. 82 tons/h Bale weight 800 up to 1300 kg, depends on material and bale lenght SPS controller (manuf., type) Telemecanique TSX Micro Operating panel (manuf., type) Schneider MAGELIS Touch Baler dimensions built up with hopper 13,200 x 27,000 x 7,344 mm (l x w x h) Transport dimensions only baler 13.200 x 2.750 x 3.450 mm (l x w x h) Machine weight baler approx. 52 tons Technical data chain belt conveyor: Manufacturer Bollegraaf Typ HBT 1216 Year of construction 2009 Driving motor 7,5 kW Length feeding conveyor 6,750 mm Length elevating conveyor 14,400 mm Length goose neck 2,150 mm Grade 30° Effecting width 1,754 mm Height of side wall feeding conv. 500 mm Height of side wall elevating conv. 800 mm Weight 16 t Pit dimensions 10,000 x 3,200 x 1,200 mm (l x w x d) Comments: The press is currently in operation and is to be replaced by a new machine in the 2nd quarter of 2026. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors.

Condition: good (used), Year of construction: 2014, operating hours: 7,145 h, functionality: fully functional, Baling Press Presto HPK 50 HS, Year of Manufacture 2014 Manufacturer: Presto Model: HPK 50 HS Year of manufacture: 2014 Drive: 30 kW Pressing force: 50 t Operating hours: 7,145 Filling opening: 1,600 x 650 mm (L x W) Channel cross-section: 700 x 950 mm Max. filling volume: 1.06 m³ Cycle time: 20 s Tying: 4-fold Throughput capacity at 35 kg/m³: 5.5 t/h 60 kg/m³: 8.8 t/h 100 kg/m³: 12.7 t/h Bale weight: up to 500 kg Machine dimensions: 8,420 x 1,900 x 2,400 mm (L x W x H) Machine weight: approx. 10,500 kg Materials: Paper, cardboard, film, PET bottles The press is in good condition and has been inspected and tested. A video can be found on our YouTube channel or our website. Note: The press has been overhauled. The knives, counter-knives, and all sliding plastics have been replaced. Please note: All technical data are based on the manufacturer's information. We assume no liability for the information provided or for possible errors. The offer is non-binding, subject to prior sale, and can be withdrawn at any time. Inspections are possible by appointment. Codpjxzz U Aefx Abbshf Sale is ex-works, prepayment only, without warranty or guarantee.

Condition: ready for operation (used), Year of construction: 2008, Brand: HSM Model: V-Press 1160 plus Year of manufacture: 2008 Pressing force: 532 kN Voltage: 400V Max. bale weight: up to 550 kg (depending on the material) Bale dimensions: 120 x 110 x 120 cm Machine weight: 2403 kg Csdjxx Slajpfx Abbjhf Machine dimensions: 180 x 157 x 298.5 cm Filling opening dimensions: 119.5 x 65 cm Condition: very good! Function tested. FLITS Rental & Sales service: With every machine, we provide a bundle of baling wire (120 wires). Need more baling wire bundles? Request a free quote without obligation. FLITS Rental & Sales is your reliable partner for the sale and rental of high-quality machines for both businesses and individuals. We focus on delivering efficient solutions in internal logistics, cleaning, waste processing, and working at heights. Waste baler, Paper baler, Cardboard baler, Plastic baler, Waste compactor, Recycling, Textile baler, Waste processing.

Condition: good (used), Year of construction: 2001, Garbage compactor, garbage press, press container, garbage container, self-compacting compactor, waste press, paper press container, paper container, cabinet press, vertical baler -Manufacturer: Husmann, cabinet press vertical baler -Type: KBP 20 -Drive power: 3 kW -Pressure: 20 t Csdpfjxg Dp Tsx Abbshf -Filling opening: W x H 1250 x 680 mm -Bale ejection device: bale dimensions 1200x950x850 mm -Transport dimensions: 1450/1160/H2980 mm -Weight: 1300 kg

Condition: used, Year of construction: 2003, functionality: fully functional, Baling Press Presto CC 13 V, Year of Manufacture 2003 Technical Specifications: Manufacturer: Presto Model: CC 13 V Year of Manufacture: 2003 Pressing Force: 13 t Cycle Time: 24 s Drive Power: 4 kW Feed Opening: 780 x 750 mm Feed Volume: 0.39 m³ Binding: triple, automatic Throughput at bulk density of 35 kg/m³ - 1.7 t 60 kg/m³ - 2.5 t 100 kg/m³ - 3.8 t Bale Dimensions: 700 x 750 mm Bale Weight: up to 250 kg Dimensions: 2800 x 1050 x 1830 mm (LxWxH) Cjdpfx Asw Tyxljbbehf Machine Weight: approx. 1,900 kg Materials: paper, cardboard, film The press is in good condition and has been function tested. Please note: All technical data is based on manufacturer specifications. We do not assume any liability for the information provided or for possible errors. This offer is non-binding, subject to prior sale and may be withdrawn at any time. Viewing by appointment. Sale is ex works, advance payment required, without warranty or guarantee.

Condition: ready for operation (used), Year of construction: 2013, Brand: HSM Model: V-press 860 Year of manufacture: 2013 Pressing force: 418 kN Voltage: 400 V Max. bale weight: 430 kg (depending on material) Bale dimensions: 120 x 110 x 85 cm Machine weight: 2,083 kg Machine dimensions: 180 cm x 125 cm x 298.5 cm Chjdpoxx Ntbjfx Abbsf Filling opening dimensions: 120 cm x 65 cm x 85 cm Condition: very good! Functionality checked. FLITS Rental & Sales service: with every machine, we supply one bundle of tying wire (120 wires).

Condition: good (used), Year of construction: 2013, functionality: fully functional, Bale Press Dixi 60 SLS, Year of Manufacture 2013 Technical Data: Manufacturer: Maschinenfabrik Bermatingen Year of Manufacture: 2013 Pressing Force: 60 t Drive Power: 11 kW, 32 A Filling Opening: 990 x 1110 mm (W x L) Bale Dimensions: 1100 x 800 x 1200 mm Bale Weight: approx. 370-450 kg Chjdpfx Abjxyga Ijbof Tying: triple manual Machine Dimensions: approx. 4870 x 2100 x 2150 mm (L x W x H) Weight: approx. 5220 kg Materials: PET, paper, cardboard, film The operating manual and EC Declaration of Conformity are available in German. Please note: All technical data is based on manufacturer information. We do not assume liability for the accuracy of the information provided or for any possible errors. This offer is non-binding, subject to prior sale, and may be withdrawn at any time. Inspections are possible by arrangement. Sale is ex works, against prepayment, without warranty or guarantee.

Condition: ready for operation (used), Year of construction: 2009, Brand: HSM Model: V-Press 1160 plus Year of manufacture: 2009 Pressing force: 532 kN Voltage: 400 V Maximum bale weight: up to 550 kg (depending on material) Bale dimensions: 120 x 110 x 120 cm Machine weight: 2403 kg Chsdpsxwa Dzefx Abbjf Machine dimensions: 180 x 157 x 298.5 cm Filling opening dimensions: 19.5 x 65 x 111.5 cm Condition: Very good! Checked for proper operation. FLITS Rental & Sales service: every machine comes with a bundle of binding wire (120 wires). Need more binding wire bundles? Request a free quote. At FLITS Rental & Sales you choose speed, clarity, and reliability. We think along with you, respond promptly, and ensure you quickly have access to the right machine. You are welcome to inspect the machines at our location: Schoterlandseweg 94, 8413NE Oudehorne. Visits are possible by appointment, so we can take the time to properly inform you and show you the right machines. We are happy to assist you! Waste baler Paper baler Cardboard baler Plastic baler Waste compactor Recycling Textile baler Waste Waste processing

Condition: good (used), Year of construction: 2016, functionality: fully functional, Baler Dixi 60 SLS, Year of manufacture 2016 Technical Data: Manufacturer: Maschinenfabrik Bermatingen Year of manufacture: 2016 Pressing force: 60 t Drive power: 11 kW, 32 A Feed opening: 990 x 1110 mm (W x L) Bale dimensions: 1100 x 800 x 1200 mm Bale weight: approx. 370-450 kg Tying: 3-fold manual Machine dimensions: approx. 4870 x 2100 x 2150 mm (L x W x H) Weight: approx. 5220 kg Materials: PET, paper, cardboard, film Chsdpfxexygauo Abbsf The operating manual and EC Declaration of Conformity are available in German. Please note: All technical specifications are based on manufacturer information. We do not accept any liability for the details provided or for potential errors. This offer is non-binding, subject to prior sale, and may be withdrawn at any time. Inspections are possible by prior appointment. Sale is ex-works against advance payment, without warranty or guarantee.

Condition: excellent (used), Year of construction: 2021, functionality: fully functional, Bollegraaf HBC 120 baler with pre-compressor and air separator, year of manufacture 2021, in very good condition Technical specifications: Manufacturer: Bollegraaf Model: HBC 120 Year of manufacture: 2021 Operating hours: 5,800 (as of October 2025) Pressing force: 120 t Drive power: 90 kW Total power: 141 kW Capacity at 30 kg/m³: 16.2 t/h 50 kg/m³: 25 t/h 100 kg/m³: 47 t/h Bale size: 1,100 x 720 mm (W x H), variable length Bale weight: 550–880 kg Tying: 5-fold vertical Dimensions: approx. 11,750 x 2,500 x 4,590 mm (L x W x H) Weight: approx. 31,600 kg Scope of delivery includes the baler with pre-compressor, perforator, binding platform, large digit display, remote control, wire stand, and preparation for a personnel safety system. Materials: paper, cardboard, film, PET, beverage cans, textiles. The baler is in very good condition. It will remain in operation for approximately another 4 months and can be inspected under operating conditions upon request. Please note: All technical specifications are based on the manufacturer's information. We do not accept any liability for the information provided or for potential errors. All offers are subject to change, prior sale and withdrawal at any time. Chjdpfjxwazysx Abbjf Viewings can be arranged by appointment. Sale is ex location, without warranty or guarantee.

Condition: reconditioned (used), Year of construction: 2009, operating hours: 15,334 h, functionality: fully functional, Europress EP 6500 V5 H4, Cross Tying, Year 2009, Fully Workshop Overhauled Chedpfxjw Rlf Eo Abbjf Technical Data: Manufacturer: Europress Type: 6500 V5 H4 Year of manufacture: 2009 Operating hours: approx. 15,334 hrs Number of bales: 138,097 Main press force: 120 t Specific press force: 142 kg/cm² Feed opening dimensions: 1,650 x 1,100 mm Fill volume: 3 m³ Filling volume per press cycle: 1.58 m³ Bale dimensions: 730 x 1,100 mm Drive power: 75 kW (1 x 30 kW + 1 x 45 kW, individually switchable) Total connected load: 83 kW Current consumption: 150 A Binding: 5-fold vertical, 4-fold horizontal, fully automatic Bale weights: 450-900 kg Hydraulic oil tank volume: 1,200 L PLC control: Siemens S7-200 Operator panel: Siemens touchscreen Press dimensions (assembled with hopper): 13,465 x 5,200 x 5,074 mm Transport dimensions (press only): 9,965 x 2,500 x 2,900 mm (L x W x H) Machine weight (press): approx. 28 t Overhaul Work Performed on the EP 6500 V5: - Completely de-rusted and repainted - Full renewal of the interior steel floor of the press - Overhaul of plunger (steel construction) - Complete overhaul of horizontal and vertical lance boxes - Full replacement of internal Hardox lining - All hydraulic hoses replaced - Both lifting cylinders renewed - Knives and counter-knives replaced - All hydraulic cylinders resealed and tested - All guide and sliding plastics renewed - Wire deflection pulleys replaced - Various cables and sensors replaced - Various electrical components (control cabinet) renewed - Complete check of electrical system/control - Full pressure test of hydraulic system Remarks: The machine has been overhauled, checked, and tested by us. You can find a video on our website or YouTube channel. Inspections, including powered operation, are possible at any time by appointment. On request, we are also happy to perform test runs with your material for a fee. For questions about the machine, you may also contact us by phone from Monday to Thursday, 08:00 to 14:00. On Friday, we are available from 08:00 to 13:00. Please note: All technical data refer to the manufacturer’s specifications. No liability is accepted for the accuracy of the information provided or for any possible errors. This offer is non-binding, subject to prior sale and can be revoked at any time. Inspection possible by appointment. Sale is ex location, without warranty or guarantee.

Condition: used, Year of construction: 2017, operating hours: 1,640 h, functionality: fully functional, Presto CC 40 M Baler Technical Data: Manufacturer: Presto Model: CC 40 M Year of manufacture: 2017 Pressing force: 40 t Cycle time: 34 s Drive power: 15 kW Filling opening: 1080 x 1100 mm Csdpfx Abjxuq E Djbehf Filling volume: 0.85 m³ Binding: 4-fold, polyester strapping, manual Throughput at bulk density of: 35 kg/m³ – 1.8 t/h 60 kg/m³ – 2.5 t/h 100 kg/m³ – 3.1 t/h Bale size: 750 x 1100 mm Bale weight: 400 kg Dimensions: 3650 x 1590 x 2010 mm (LxWxH) Machine weight: approx. 3,800 kg Materials: Paper, cardboard, film The baler is in good condition. Operating manual and CE declaration are available. Note: Channel discharge is fully automatic and adjustable. Please note: All technical data are as stated by the manufacturer. We accept no liability for the information provided or for any errors. This offer is subject to change, prior sale reserved, and may be revoked at any time. Inspections are possible by appointment. Sale is ex works, prepayment only, without warranty or guarantee.