Used waste compactors for sale (317)

Condition: good (used), Year of construction: 2010, operating hours: 3,641 h, functionality: fully functional, pressing force: 36 t, filling opening width: 1,100 mm, filling opening length: 1,080 mm, bale width: 1,100 mm, bale height: 750 mm, power: 15 kW (20.39 HP), volume flow: 90 m³/h, Technical data baler: Manufacturer Presto GmbH & Co. KG Typ CC 36 M Year of construction 2010 Hours of operation 3,641 h Press power main press 36 t Specific press capacity 467 N/cm² Feed channel 1.080 x 1100 mm (l x w) Cycle time 34 sec. Capacity per cycle time 0,85 m³ Theoretic throughput rate 90 m³/h Throughput rate under operating conditions with a material bulk density of 35 kg/m³ approx. 51 m³/hour Bale size 1100 x 750 mm (w x h), length variable Driving motor 15 kW Tying 4-fold vertical, semi-automatic, with polyester synthetic yarn Throughput rate at a bulk weight of 35 kg/cbm 1,8 to/h bulk weight of 60 kg/cbm 2,5 to/h bulk weight of 100 kg/cbm 3,1 to/h Transport dimensions only baler 4.200 x 1.640 x 2.200 mm Machine weight baler approx. 4 to Bsdpfx Akju Thh Eeaslg Comments: The press was checked for function in our workshop, then stored and is therefore available at short notice. The machine documentation (operating instructions, CE, electrical and hydraulic circuit diagram) is available. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors.

Condition: reconditioned (used), Year of construction: 2015, operating hours: 28,748 h, functionality: fully functional, pressing force: 60 t, filling opening width: 1,100 mm, filling opening length: 1,500 mm, bale width: 1,100 mm, bale height: 750 mm, bale weight: 570 kg, overall weight: 20,000 kg, oil tank capacity: 600 l, power: 37 kW (50.31 HP), volume flow: 350 m³/h, Technical data baler: Manufacturer Presona AB, Sweden Type LP 60 VH1 Year of construction 2015 Total operating hours, 30,143 hours, as of July 2025 Effective pump running time onl 6,527 hours, as of July 2025 Number of pressed bales 115,193 bales, as of July 2025 Press force pre press 25 t Main press force 60 tonnes Specific pressing force 73N/cm² Dimensions of feed chute 1,500 x 1,100 mm Filling volume / pressing cycle 2.7 m³ Theoretical throughput capacity 800 m³/hour Throughput capacity under operating conditions 350 m³/hour Bale dimensions 1,100 x 750 mm Drive power 37 kW Tying 5-fold vertical, fully automatic Throughput capacity with a Bulk weight of 50 kg/cbm 11 to 14 tonnes/hour Bale weights 420 to 570 kg, depending on material Hydraulic oil tank volume 600 litres Baler dimensions assembled with hopper 10,100 x 3,750 x 4,310 mm (l x w x h) Transport dimensions excluding press 10,100 x 2,400 x 3,000 mm (l x w x h) Machine weight press approx. 20 tonnes Condition of the press: Bledpevn Tg Iefx Akasg The press was partially overhauled in our workshop and then tested in manual and automatic mode. The following overhaul work was carried out: Machine cleaned, partially derusted and partially repainted Hydraulic oil tank emptied and cleaned Oil filter and air filter replaced, new hydraulic oil filled Press ram dismantled and cleaned All four rollers removed from the press ram and replaced Grease cartridges of the automatic roller lubrication system replaced Slide rails cut out from the press floor in the press room Underbody reinforced with welded sheets New HARDOX slide rails welded in Wire station with deflection rollers for the lower wire cleaned and made operational Slide rails cut out from the floor in the press channel New HARDOX slide rails welded in Both side walls of the press channel dismantled, derusted Worn side wall plates cut out Complete side walls covered with new wear plates and welded Main hydraulic cylinder dismantled and disassembled for inspection Piston rod replaced, cylinder tube honed Complete seal set replaced, pressure test carried out Vertical needle system for binding dismantled, cleaned, wire deflection rollers made functional and serviced Chain cleaned, greased, chain tension readjusted Drillomat cleaned, wire knife, drill shafts and drill fingers checked, retightened with torque and serviced Machine checked, general maintenance work carried out and press tested in manual and automatic mode Comments: The press is sold without a conveyor belt and without wire stations. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors.

Condition: reconditioned (used), Year of construction: 2005, operating hours: 30,408 h, functionality: fully functional, pressing force: 50 t, filling opening width: 1,100 mm, filling opening length: 1,250 mm, bale width: 1,100 mm, bale height: 720 mm, bale weight: 550 kg, overall weight: 16,000 kg, oil tank capacity: 600 l, year of last overhaul: 2024, Technical data baler: Manufacturer Presona AB Type LP 50 EH1 Year of construction 2005 Operating hours 30,408 hours, as of April Number of pressed bales 198,059 as of April Pressing force main press 50 tonnes Specific pressing force 63 N/cm² Theoretical throughput capacity 530 m³/hour Throughput capacity under operating conditions 260 m³/hour Dimensions of feed chute 1,250 x 1,100 mm Bale chamber volume 2.2 m³ Bale dimensions 1,100 x 720 mm, variable length Drive power 22 kW Tying 5-fold vertical, fully automatic Throughput rates with a bulk density of 30 kg/cbm 6 up to 7 tonnes/hour Bulk weight of 50 kg/cbm 7 up to 9 tonnes/hour Bljdpfx Aksu Thhreaog Bulk weight of 100 kg/cbm 11 up to 14 tonnes/hour Bale density (paper/newspapers) 400 to 550 kg/m³ Hydraulic oil tank capacity 600 litres PLC control Telemecanique TSX Micro Schneider Magelis control panel Effective transport dimensions excl. baler 8,125 x 2,300 x 3,000 mm (L x W x H) Transport weight press approx. 16 tonnes Condition of the baler: The machine was partial overhauled in our workshop and general maintenance work was carried out. After completion of the overhaul work, the press was tested during operation and is available for sale at short notice. The following overhaul work was carried out: General work: Machine cleaned, derusted, primed, partially painted Wire entry marks in the press channel feed-throughs welded shut and smoothed Hydraulic unit: Hydraulic oil tank emptied, tank cleaned, new oil filled Oil filter and air filter replaced Leaky oil sight glass on hydraulic oil tank replaced All hydraulic hoses replaced Electrics: English language installed in the programme menu Two key switches in the control panel replaced Control cabinet replaced Signal lamp on the control cabinet replaced Flaps end switch replaced Electrical system of the turbulator replaced, connected and tested Press ram: All four rollers removed from the press ram and replaced Main hydraulic cylinder dismantled, disassembled and partially overhauled, cylinder tube honed, complete seal set replaced, leak test performed All plastic wear pads on the press ram replaced Pre-press: Both bearings on the pre-press shaft replaced. Both hydraulic cylinders dismantled, disassembled and partially overhauled, both cylinder tubes honed, complete seal sets replaced, leak test performed. Scraper flap on the pre-press replaced. Binding system: Two complete needles with wire deflection rollers replaced Needles adjusted and set All wire deflection rollers in the needle heads replaced Drill fingers replaced Two drill shafts replaced All 8 wear plates on the Drillomat, under the drill fingers, replaced Scope of delivery: Only the baler will be sold. The documentation (Manual, CE-declaration, electr./hydr.-drawings), are completely available. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors.

Condition: refurbished (used), Year of construction: 2019, operating hours: 3,000 h, functionality: fully functional, pressing force: 70 t, overall weight: 9,500 kg, filling opening width: 420 mm, filling opening length: 1,250 mm, Technical data packing press / can press / metal sheet press: Manufacturer unoTech GmbH Type UPAXX 70 Year of manufacture 2019 Operating hours approx. 3,000 hours Pressing force 700 kN at 315 bar Filling opening chute 420 x 1,250 mm (d x w) Channel cross-section (package dimension) 350 x 500 mm (h x w), length depending on material Drive power 30 kW Connected load 40 kW Power consumption, total 70 A Throughput capacity for empty beverage cans with: one pressing stroke approx. 1.7 t/hour two pressing strokes approx. 2.5 t/hour Bedpju Th S Sefx Akaolg Achieved compaction approx. 1200 kg/m³ Hydraulic oil tank capacity 850 l Press dimensions built up 8,000 x 1,600 x 2,500 mm (l x w x h) Transport weight press approx. 9.5 t Accessories: Oil cooler 1.5 kW, oil tank heater 1.5 kW, press box made of wear-resistant steel S355 Material properties: According to the manufacturer, this machine is suitable for pressing tin cans, metal sheet offcuts, sheet steel as well as aliminium, brass and copper waste. Condition of the baler: The can press was completely overhauled in our workshop. The press is in a very good condition, see the functional video after the overhaul and is sold with the 12 months OBM parts warranty. Comments: The documentation (Manual, CE-declaration, electr./hydr.-drawings), are completely available. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors.

Condition: reconditioned (used), Year of construction: 2002, operating hours: 44,590 h, functionality: fully functional, pressing force: 200 t, filling opening width: 1,020 mm, filling opening length: 2,000 mm, bale width: 1,100 mm, bale height: 1,100 mm, oil tank capacity: 3,100 l, power: 150 kW (203.94 HP), year of last overhaul: 2025, Technical data baler: Manufacturer MACPRESSE EUROPA S.R.L. Typ 112 Year of construction 2002, partially refurbished in December 2025 Operating hours 44,590 hours, stand December 2025 Press power main press 200 tons Specific press capacity 16,5 kg/cm² Feed channel 2,000 x 1,020 mm Filling volume 2,65 cm³ Theoretic throughput rate 795 m³/h Bale size 1,100 x 1,100 mm, length variable Driving motor 2 x 75 kW Tying system 5-fold horizontal, full automatic Throughput rate at MSW approx. 48 up to 54 tons/h, depends on material Volume hydraulic oil tank 3,100 l Machine weight baler approx. 50,8 tons Scope of delifery: 1 piece baler MACPRESSE, type 111A 1 operating manual with CE declaration, electrical and hydraulic circuit diagram Comments: The machine was serviced and partially overhauled in our workshop. The following work was carried out and parts replaced: • Hydraulic oil tank emptied and cleaned • Oil and air filters replaced • New hydraulic oil filled Bsdpfxox Dnb Us Akaolg • All hydraulic hoses replaced • Press ram dismantled, broken down into individual parts, mechanics made operational • Front two main rollers replaced • Knives on the press ram replaced • Main hydraulic cylinder dismantled, disassembled, cylinder tube and piston rod checked, complete seal set replaced • Counter knife in the frame replaced • Knife gap adjusted to approx. 3 mm • Upper steel guide rails in the frame on the left and right replaced. • Worn press base cut out, base plate replaced with wear-resistant HARDOX steel. • Binding and twisting unit dismantled, broken down into individual parts, mechanics made functional, all twisting shafts and ball bearings replaced. • All wire rollers in the needle heads replaced • Wire knives cleaned and readjusted, chains greased and tensioned • All wire deflection rollers made operational • All door contact switches replaced • Wirbulator device dismantled, disassembled and made operational • General maintenance work carried out Finally, the press was subjected to a machine test in manual and automatic mode, see our video for the machine function test. The documentation (BA, CE, electrical/hydraulic circuit diagram) is complete. Viewing is possible by appointment. We accept no liability for the technical specifications or any errors.

Condition: reconditioned (used), Year of construction: 1996, functionality: fully functional, pressing force: 170 t, filling opening width: 1,020 mm, filling opening length: 1,800 mm, bale width: 1,100 mm, bale height: 1,100 mm, overall weight: 40,000 kg, oil tank capacity: 3,000 l, year of last overhaul: 2024, For sale is a used baling press system consisting of a chain belt conveyor for underfloor operation, with a feed hopper, a hydraulic pre-compactor with whirlulator, a MACPRESSE 111A baling press, two complete wire drawing frames with 5 wire reel stands each, without wire. Technical data baler: Manufacturer MACPRESSE EUROPA S.R.L. Typ 111A Year of construction 1996, refurbished in 10/2024 Press power main press 170 tons Specific press capacity 14 kg/cm² Feed channel 1,800 x 1,020 mm Filling volume 2,5 cm³ Theoretic throughput rate 750 m³/h Bale size 1,100 x 1,100 mm, length variable Driving motor 2 x 55 kW Tying system 5-fold horizontal, full automatic Throughput rate at a approx. 30 up to 35 tons/h, depends on material Volume hydraulic oil tank 3,000 l Transport dimensions of press with new machine feets 113,700 x 2,300 x 2,900 mm (l x w x h) Machine weight baler approx. 40 tons Comments: The baler was partially overhauled in our workshop and tested after completion of the work, please look at our functional video. The system was previously used to bale paper and cardboard from municipal collections. The contract was awarded elsewhere after the end of the contract period, so the complete system is for sale. The overhaul work carried out and the spare parts replaced can be found in the detailed photo documentation and in our quotation. The documentation (Manual, CE, electr./hydr.-drawings), are completely available. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors. Technical data conveyor belt: Manufacturer Wagensfeld B.V. Type chain belt conveyor 1700 mm Year of construction 2017 Drive power 7.5 kW Belt speed 14 m/minute Length of infeed conveyor 6,900 mm Length of ascending belt 12,885 mm Length of gooseneck 1,747 mm Overall length 21,271 mm Pitch 32° Effective width 1,644 mm Height of drive shaft above ground 5,777 mm Wall height of feed conveyor 500 mm Wall height of ascending conveyor 880 mm Steel flights height 40 mm Distance between flights 1200 mm Transport dimensions conveyor disassembled 15,005 x 2,503 x 2,435 mm (l x w x h) Pit dimensions 11,500 x 2,700 x 1,015 mm (l x w x d) Remarks: Bljdpfx Aou Th D Rskajg The chain belt conveyor, built in 2017, was later made to fit the baler during the last installation of the baler in the Netherlands and is newly installed. The conveyor belt is in good, operational condition and has therefore not been overhauled. An installation drawing with the pit dimensions is available. Scope of delifery: 1 chain belt conveyor, Wagensveld B.V. 1 piece feed hopper with pre-compressor flaps 1 piece wirbulator 1 baler MACPRESSE, type 111A 2 wire drawing frames with wire reel stands, without wire 1 operating manual with CE declaration, electrical and hydraulic circuit diagram

Condition: reconditioned (used), Year of construction: 2007, operating hours: 13,209 h, functionality: fully functional, pressing force: 50 t, filling opening width: 1,050 mm, filling opening length: 1,250 mm, bale width: 1,100 mm, bale height: 700 mm, bale weight: 500 kg, oil tank capacity: 400 l, year of last overhaul: 2025, volume flow: 108 m³/h, Technical data baler: Manufacturer according to type plate BRAMIDAN (original manufacturer Presto GmbH & Co. KG) Type HC 50 (corresponds to the Presto HPK 50) Year of manufacture 2007 Operating hours 13,209 hours, as of March Number of bales pressed: 23,379 bales Pressing force 50 tonnes Specific pressing force 650 kN/m² Feed chute dimensions 1250 x 1050 mm (L x W) Filling volume 0.96 cm³ Theoretical cycle time 32 seconds Theoretical throughput capacity 108 m³/hour Bale dimensions 1100 x 700 mm (w x h) length variable Drive power 15 kW Power consumption, total in 50 A Tying 4-fold vertical, fully automatic Throughput rates with a bulk density of 30 kg/cbm approx. 3.1 t/hour Bulk weight of 60 kg/cbm approx. 4.5 tonnes/hour Bulk weight of 100 kg/cbm approx. 7.2 tonnes/hour Bale weights with a bale length of approx. 1.2 m up to 500 kg, depending on material Hydraulic oil tank capacity 400 litres PLC control Siemens S7-200 Effective transport dimensions excluding baler 6780 x 1800 x 2100 mm (l x w x h) Transport weight of press 8.5 tonnes Condition of the baler: The press was used in a production facility exclusively for pressing cardboard and was regularly serviced. With only 13,209 operating hours, the machine has seen little use. The press was partially overhauled in our workshop and then tested. The following overhaul work was carried out: Machine cleaned Bale retainer made operational and lubricated Light barrier replaced Twisting unit completely dismantled, broken down into individual parts, all bearings replaced, all plastic glides replaced, lubricated, chain tension adjusted Knife and counter knife dismantled, sharpened, reassembled Knife gap readjusted General maintenance work carried out and lubricated Scope of delivery: Bledpow U Dt Nefx Akasg 1 baler with wire roll boxes, without wire 1 set of machine documentation Comments: The documentation (Manual, CE-declaration, electr./hydr.-drawings), are completely available. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors.

Condition: reconditioned (used), Year of construction: 2007, operating hours: 22,605 h, functionality: fully functional, pressing force: 100 t, filling opening width: 1,100 mm, filling opening length: 1,600 mm, bale width: 1,100 mm, bale height: 1,100 mm, bale weight: 1,400 kg, overall weight: 36,000 kg, oil tank capacity: 1,300 l, For sale is a overhauled baler, with 100 tonnes pressing force, large format 1100 x 1100 mm, 75 kW drive power and 10-fold cross binding Technical data baler: Manufacturer Bollegraaf Typ HBC 110 K / 75 kW Year of construction 2007 Press power main press 100 tons Press power of pre-press 50 tons Operating hours 22,605 hours Feed channel 1,600 x 1,100 mm Capacity per cycle time 3,15 m³ Theoretic cycle time 19 sec. Bale size 1,100 x 1,100 mm Driving motor 75 kW Connected load 126 kW Full load current 238 A Tying system 5-fold vertical, 5-fold horizontal, fully automated Throughput rate at a bulk weight of 30 kg/cbm approx.16 tons/h bulk weight of 50 kg/cbm approx. 25 tons/h bulk weight of 100 kg/cbm approx. 47 tons/h Bale weight up to 1400 kg, depends on material and bale lenght Volume oil tank approx. 1,300 l SPS controller Telemecanique TSX Micro Operating panel Schneider MAGELIS Touch Baler dimensions built up with hopper 11,750 x 5,000 x 7,105 mm (l x w x h) Transport dimensions only baler 11.750 x 2.500 x 3.450 mm (l x w x h) Machine weight baler approx. 36 tons Comments: The press was partially overhauled and serviced in our workshop and tested and stored after completion of the work. The machine is available at short notice and can be inspected in our warehouse by appointment. The following overhaul work was carried out: Rust removal and partial painting of the press. Remaining hydraulic oil tank drained, oil filter and air filter replaced. New hydraulic oil topped up. All hydraulic hoses replaced. Main hydraulic cylinder, two cylinders of the prepress flap and the cylinder of the press channel dismantled, disassembled, checked, cylinder tubes honed, all seal sets replaced and a final pressure test carried out. Disassembly of the prepress flap with bearings and bearing blocks. 1st and 3rd circular arc segmet cut out and a new one welded in again. Both bearings of the shaft of the prepress flap replaced. Upper material deflector on the frame of the prepress flap replaced. Press ram dismantled, checked and both front rollers replaced. Material deflectors and wear profiles on the sides and base of the press ram cut off and new ones welded in. Horizontal and vertical needle and tying unit dismantled, disassembled, checked, plastic sliding plates, bearings of the drill shafts and wire deflection rollers with bearings in the needle heads replaced. Both bronze slide rails on the left and right in the frame cover to the press ram replaced. Blodpfxjvf E Avj Akasg Both wire deflection units on the left and right, with bale retaining clamps, completely renewed. Wire insertion unit including hydraulic cylinder under the needle feedthroughs completely renewed. Wire entry marks in the floor and side walls of the bale chamber welded shut and smoothed. General maintenance and service work carried out in accordance with the manufacturer's specifications. Press was tested in manual and automatic mode, accepted and stored after completion of overhaul work. We accept no liability for the technical specifications or any errors.

Condition: reconditioned (used), Year of construction: 2000, operating hours: 32,169 h, functionality: fully functional, pressing force: 60 t, filling opening width: 1,100 mm, filling opening length: 1,320 mm, bale width: 1,100 mm, bale height: 720 mm, bale weight: 750 kg, overall weight: 22,000 kg, oil tank capacity: 900 l, For sale is a complete baling system consisting of conveyor technology, baling press (partially refurbished and tested) and wire stations. Technical data baler: Manufacturer Bollegraaf Recycling Machinery B.V. Typ HBC 60A Year of construction 2000 Hours of operation 32,169 hours, stand November 2024 Press power main press 60 tons Press power of pre-press max. 25 tons Feed channel 1,320 x 1,100 mm Theoretic cycle time 18 sec. Bale size 1,100 x 720 mm, lenght variable Driving motor 45 kW Connected load 60 kW Tying system 5-fold vertical Throughput rate at a bulk weight of 30 kg/cbm approx. 5,5 tons/hour bulk weight of 50 kg/cbm approx. 10 tons/hour bulk weight of 100 kg/cbm approx. 16 tons/hour Bale weight 400 up to 750 kg, depends on material SPS controller Telemecanique TSX Micro Machine weight baler approx. 24 tons Scope of delivery: 1 piece chain belt conveyor 1 Bollegraaf HBC 60A baler with whirling unit 1 maintenance platform with access ladder 2 wire stations with deflection rollers for 10 wire reel stands (without wire) Blodpfxsviwdmo Akajg The following repair and overhaul work was carried out: Hydraulic oil tank emptied, cleaned and refilled with new oil Oil filter and air filter replaced Hydraulic block partially resealed Hydraulic hose on hydraulic block replaced Wire entry marks on the floor passages welded shut and smoothed Tying unit cleaned, serviced Electrical system repaired, door flap contact switch partially replaced Whirbulator repaired General maintenance work carried out, lubricated Machine tested during operation, without the use of materials, in manual mode and in automatic mode, see function video Comments: The system has already been completely dismantled, stored and is available for loading at short notice. The documentation (BA, CE, electrical/hydraulic circuit diagram) is available. Viewing is possible by appointment. We accept no liability for the technical details or any errors.

Condition: reconditioned (used), Year of construction: 2009, operating hours: 22,029 h, functionality: fully functional, pressing force: 80 t, filling opening width: 1,000 mm, filling opening length: 1,400 mm, bale width: 1,100 mm, bale height: 750 mm, bale weight: 600 kg, overall weight: 16,000 kg, power: 45 kW (61.18 HP), year of last overhaul: 2025, Technical data baler: Manufacturer Avermann Maschinenfabrik GmbH & Co. KG, Germany Type AVOS 1410-45/80 Year of construction 2009 Operation hours 22,029 hours, as of December 2025 Press power main press 80kN Specific press force 103,9 N/cm² Feed channel 1,400 x 1,000 mm Theoretic cycle time 12 sec Theoretic throughput capacity 300 m³/h Bale size 1,100 x 750 (w x h), the length is variable Blsdpfjx A U Ncex Akaog Drive power 45 kW Connected load 75 kW Tying system 4-fold, vertical, fully automatic Throughput capacity at a bulk weight of 30 kg/cbm approx. 6,0 t/h bulk weight of 50 kg/cbm approx. 10,5 t/h bulk weight of 100 kg/cbm approx. 17,5 t/h Bale weight with a bale length of approx. 1.2 m up to 600 kg, depends on material SPS controller Siemens S7-300 Operating panel pulsotronic Baler dimensions built up 8,610 x 2,400 x 3,835 mm (l x w x h) Transport weight baler approx. 16 t Special equipment: Wear-resistant floor made of HARDOX steel Special press ram for pressing ‘difficult’ materials and loose bulk materials with small grain sizes Control cabinet air conditioning Machine foot elevation 200 mm Remark: The machine was serviced and partially overhauled in our workshop. The following work was carried out and parts replaced: • Dismantling of the press ram, disassembly into individual parts, reconditioning of the mechanics, replacement of the following plastic wear plates and rails: o Plastic wear rails left/right under the press ram o Plastic wear rails left/right above the press ram o Plastic main wear plate (support plate) in the centre under the press ram • Steel guide rails on the left/right in the frame • Replacement of the entire base plate, four-piece, made of wear-resistant HARDOX steel • Wire inlet rails in the press floor newly welded and smoothed • Replacement of the counter blade, two-piece, in the frame • Adjustment of the blade gap to approx. 2.5 mm • Dismantling of the binding and twisting unit, disassembly into individual parts, loosening of the mechanics, replacement of all deep groove ball bearings and axial ball bearings on the twisting shafts, wire blades cleaned and readjusted, chains greased and tensioned • Support roller in front of the twisting shafts replaced • All hydraulic hoses replaced • Oil filter and air filter replaced • Main hydraulic cylinder checked for leaks • The hydraulic oil is only one year old, has been chemically analyzed, is still in good condition, and has therefore not been changed but can continue to be used. • General maintenance work carried out Finally, the press was subjected to a machine test in manual and automatic mode; see video for the machine function test.

Condition: ready for operation (used), Year of construction: 2009, bale weight: 550 kg, total width: 1,570 mm, total height: 2,985 mm, overall weight: 2,403 kg, total length: 1,800 mm, filling opening width: 1,195 mm, filling opening length: 65 mm, bale width: 110 mm, bale length: 120 mm, bale height: 120 mm, transport height: 225 mm, Brand: HSM Model: V-Press 1160 plus Year of manufacture: 2009 Bsdoy Iwi Eopfx Akaslg Pressing force: 532 kN Voltage: 400 V Max. bale weight: up to 550 kg (depending on material) Bale dimensions: 120 x 110 x 120 cm Machine weight: 2,403 kg Machine dimensions: 180 x 157 x 298.5 cm Filling opening: 119.5 x 65 cm Condition: very good! Video of machine in operation available on request.

Condition: ready for operation (used), Year of construction: 2008, filling opening width: 1,195 mm, filling opening length: 65 mm, bale length: 120 mm, bale width: 110 mm, bale height: 120 mm, bale weight: 550 kg, total width: 1,570 mm, total height: 2,985 mm, total length: 1,800 mm, overall weight: 2,403 kg, Brand: HSM Model: V-Press 1160 plus Year of manufacture: 2008 Pressing force: 532 kN Voltage: 400 V Max. bale weight: up to 550 kg (depending on material) Bale dimensions: 120 x 110 x 120 cm Machine weight: 2,403 kg Machine dimensions: 180 x 157 x 298.5 cm Filling opening: 119.5 cm × 65 cm Condition: very good! Bodpfey Iwcxsx Akaslg Video of the machine in operation available upon request.

Condition: good (used), Year of construction: 2012, operating hours: 5,812 h, Baler Presto HPK 50 HS, year 2012, with perforator and inclined conveyor (sliding belt conveyor) Manufacturer: Presto Model: HPK 50 HS Year of manufacture: 2012 Operating hours: 5,812 Drive power: 30 kW Pressing force: 50 t Bodpfx Aksy Idifsaolg Filling opening: 1600 x 650 mm (LxW) Channel cross-section: 700 x 950 mm Max. filling volume: 1.06 m³ Cycle time: 19 s Tying: 4-fold Throughput rate at 35 kg/cbm: 5.5 t/h 60 kg/cbm: 8.8 t/h 100 kg/cbm: 12.7 t/h Bale weight: up to 500 kg Machine dimensions: 8420 x 1900 x 2400 mm (LxWxH) Machine weight: approx. 10,500 kg Perforator, hydraulically movable Drive power: 2 x 4 kW / 400 V Throughput: approx. 220 m³/h Clear feed opening: 1380 x 1200 mm Inclined conveyor: Length: 7,931 mm Belt width: 1,400 mm Total width: 2,026 mm Incline: 29° Speed: 0.6 m/s Materials: Paper, cardboard, film, PET bottles Please note: All technical data are based on manufacturer specifications. We accept no liability for the given information or possible errors. Sale is subject to prior sale and changes, and may be revoked at any time. Viewing is possible by arrangement. Sale ex works, prepayment required, without warranty or guarantee.

Condition: used, Pressing screw REG-MAC for drying films and fibers, and for compacting foam (e.g. polystyrene, EPS) Blsdpfx Aksy Icn Tsajg Drive motor 55 kw

Condition: good (used), Year of construction: 2013, functionality: fully functional, Available from 15.05.2026 Baling Press Paal Konti 325 G, Year of manufacture 2013 Technical Data: Manufacturer: Paal Model: Konti 325 G Year of manufacture: 2013 Operating hours: 11,723 (as of 10.02.26) Pressing force: 100 t Drive power: 2 x 55 kW Feed opening: 1020 x 1750 mm Bale dimensions: 750 x 1100 mm, length variable Bsdpfx Aey A Ibnokaslg Tying: 5-fold automatic Throughput rate at: 35 kg/m³ approx. 13.5 t/h 60 kg/m³ approx. 21.5 t/h 100 kg/m³ approx. 33 t/h Bale weight up to 800 kg Transport dimensions approx. 12,216 x 2,530 x 2,800 mm (LxWxH) Machine weight approx. 28,000 kg Materials: Paper, cardboard, light waste, plastic waste Please note: All technical data is based on the manufacturer's information. We do not assume liability for the details provided or for any potential errors. This offer is non-binding, subject to prior sale, and can be withdrawn at any time. Inspections are possible by arrangement. Sale against prepayment ex works, without warranty or guarantee.

Condition: good (used), Year of construction: 2019, functionality: fully functional, Baler Dixi 80 SLD, with lifting/tipping device, semi-automatic, year of manufacture 2019 Manufacturer: Dixi Model: Dixi 80 SLD Year of manufacture: 2019 Drive power: 11 kW, 400 V / 32 A Feed opening: 1,040 x 1,110 mm (W x L) Pressing force: 80 t Press cycle: approx. 35 s Capacity: approx. 1,000 kg/h Bale size: 1,120 x 1,120 x 1,200 mm (W x H x L) Bale weight: approx. 500–600 kg Binding: 4-fold, manual Machine dimensions: approx. 4,320 x 1,830 x 2,620 mm (L x W x H) Machine weight: approx. 8,000 kg Materials: Paper, cardboard, film The press is in good condition. It has been checked and tested by us. A video is available on our website or YouTube channel. Please note: Bjdpjy Avlnjfx Akajlg All technical data are based on manufacturer information. We do not accept any liability for the stated data or possible errors. This offer is subject to change without notice, prior sale, and revocation at any time. Inspection is possible by appointment. The sale is ex works, against advance payment, without warranty or guarantee.

Condition: good (used), Year of construction: 2019, functionality: fully functional, Baler Dixi 80 SLD, with lifting/tipping device, semi-automatic, year of manufacture 2019 Manufacturer: Dixi Model: Dixi 80 SLD Year of manufacture: 2019 Drive power: 11 kW, 400 V / 32 A Feed opening: 1,040 x 1,110 mm (W x L) Pressing force: 80 t Press cycle: approx. 35 s Capacity: approx. 1,000 kg/h Bale size: 1,120 x 1,120 x 1,200 mm (W x H x L) Bale weight: approx. 500–600 kg Binding: 4-fold, manual Machine dimensions: approx. 4,320 x 1,830 x 2,620 mm (L x W x H) Machine weight: approx. 8,000 kg Materials: Paper, cardboard, film The press is in good condition. It has been checked and tested by us. A video is available on our website or YouTube channel. Please note: All technical data are based on manufacturer information. We do not accept any liability for the stated data or possible errors. This offer is subject to change without notice, prior sale, and revocation at any time. Blodpfx Akjy Avhcsasg Inspection is possible by appointment. The sale is ex works, against advance payment, without warranty or guarantee.

Condition: used, Year of construction: 2012, total width: 1,700 mm, total height: 1,500 mm, total length: 1,200 mm, Empty weight: 500 kg Price: On request - Details: - └ Description: Set consisting of briquette press with extraction - Year: 2012 - Documentation available: No - CE certificate present: No - Serial number: 2012 1140 - Transport dimensions: 1200mm x 1700mm x 1500mm (l x w x h) - Transport weight [kg]: 500kg Blsdpfeyy Rt Uox Akaeg - Transport packages [pcs.]: 1 Financial information VAT: The price shown is exclusive of VAT VAT/margin: VAT deductible for entrepreneurs Delivery and trade-in always possible for everything in the industrial sectors Yorick Diebels

Condition: used, Year of construction: 2005, total width: 1,300 mm, total height: 3,850 mm, total length: 2,200 mm, Empty weight: 1.250 kg Price: On request - Year: 2005 - Documentation available: No Blodpsyrtcuefx Akaeg - CE marking present: Yes - CE certificate present: No - Serial number: 308 - Transport dimensions: 2200mm x 1300mm x 3850mm (l x w x h) - Transport weight [kg]: 1250kg - Transport packages [pcs.]: 1 Financial information VAT: The price shown is exclusive of VAT VAT/margin: VAT deductible for entrepreneurs Delivery and trade-in always possible for everything in the industrial sectors Yorick Diebels

Condition: used, Year of construction: 2005, total width: 1,300 mm, total height: 3,850 mm, total length: 2,200 mm, Empty weight: 1.250 kg Price: On request - Year: 2005 - Documentation available: No - CE certificate present: No - Serial number: 307 - Transport dimensions: 2200mm x 1300mm x 3850mm (l x w x h) - Transport weight [kg]: 1250kg - Transport packages [pcs.]: 1 Financial information VAT: The price shown is exclusive of VAT VAT/margin: VAT deductible for entrepreneurs Blsdpeym Uxtjfx Akaeg Delivery and trade-in always possible for everything in the industrial sectors Yorick Diebels

Condition: used, Year of construction: 2010, total width: 2,080 mm, total height: 1,900 mm, total length: 2,440 mm, Briquette press; Höcker Polytechnik BrikStar C 3-19-L 4.3kW, 400V 25kg/h Funnel volume 3m³ Oil tank 50l Dimensions; 2015x2360x1300mm, 830kg - Year: 2010 - Documentation available: Yes - CE certificate present: No - Transport dimensions: 2440mm x 2080mm x 1900mm (l x w x h) - Transport packages [pcs.]: 1 Financial information VAT: The price shown is exclusive of VAT Blsdoxqdxcspfx Akaog VAT/margin: VAT deductible for entrepreneurs Delivery and trade-in always possible for everything in the industrial sectors Yorick Diebels

Condition: used, Year of construction: 2017, operating hours: 854 h, total width: 2,450 mm, total height: 1,100 mm, total length: 1,900 mm, Empty weight: 800 kg Price: On request - Year: 2017 Bjdpfxexan Utj Akaelg - Documentation available: No - CE marking present: Yes - CE certificate present: No - Serial number: 5037411-000150 - Operating hours: 854 - Transport dimensions: 1900mm x 2450mm x 1100mm (l x w x h) - Transport weight [kg]: 800kg - Transport packages [pcs.]: 2 Financial information VAT: The price shown is exclusive of VAT VAT/margin: VAT deductible for entrepreneurs Delivery and trade-in always possible for everything in the industrial sectors Yorick Diebels

Condition: used, Year of construction: 1983, total width: 750 mm, total height: 900 mm, total length: 2,400 mm, Empty weight: 500 kg - Year: 1983 - Documentation available: No - CE certificate present: No Bjdpfxsxalyyj Akaelg - Transport dimensions: 2400mm x 750mm x 900mm (l x w x h) - Transport weight [kg]: 500kg - Transport packages [pcs.]: 1 Financial information VAT: The price shown is exclusive of VAT VAT/margin: VAT deductible for entrepreneurs Delivery and trade-in always possible for everything in the industrial sectors Yorick Diebels

Condition: used, Year of construction: 1998, Briquette press Weima TH 400 Year of construction 1998 Briquette diameter 50mm Capacity 60-80kg/h Machine no. 950-756 Main motor 7.5kW 200 Bar, 400V Including large collection container Machine is currently not working, the hydraulic block is leaking. - Year: 1998 - Documentation available: No - CE certificate present: No Bljdpswh I Ursfx Akaog Financial information VAT: The price shown is exclusive of VAT VAT/margin: VAT deductible for entrepreneurs Delivery and trade-in always possible for everything in the industrial sectors Yorick Diebels

Condition: used, Year of construction: 2012, total width: 1,380 mm, total height: 1,710 mm, total length: 2,100 mm, This is a set, consisting of a briquette press with extraction Exhaust capacity 5.800 m³/h - Year: 2012 - Documentation available: No - CE certificate present: No - Transport dimensions: 2100mm x 1380mm x 1710mm (l x w x h) - Transport packages [pcs.]: 1 Financial information VAT: The price shown is exclusive of VAT VAT/margin: VAT deductible for entrepreneurs Bledpfxjxr Dz Tj Akajg Delivery and trade-in always possible for everything in the industrial sectors Glenn Smeets