Condition: reconditioned (used), Year of construction: 2007, operating hours: 22,605 h, Functionality: fully functional, pressing force: 100 t, bale weight: 1,400 kg, filling opening width: 1,100 mm, filling opening length: 1,600 mm, bale height: 1,100 mm, bale width: 1,100 mm, overall weight: 36,000 kg, oil tank capacity: 1,300 l, nominal current: 238 A, For sale is a overhauled baler, with 100 tonnes pressing force, large format 1100 x 1100 mm, 75 kW drive power and 10-fold cross binding Technical data baler: Manufacturer Bollegraaf Typ HBC 110 K / 75 kW Year of construction 2007 Press power main press 100 tons Press power of pre-press 50 tons Operating hours 22,605 hours Feed channel 1,600 x 1,100 mm Capacity per cycle time 3,15 m³ Theoretic cycle time 19 sec. Bale size 1,100 x 1,100 mm Driving motor 75 kW Connected load 126 kW Full load current 238 A Tying system 5-fold vertical, 5-fold horizontal, fully automated Throughput rate at a bulk weight of 30 kg/cbm approx.16 tons/h bulk weight of 50 kg/cbm approx. 25 tons/h bulk weight of 100 kg/cbm approx. 47 tons/h Bale weight up to 1400 kg, depends on material and bale lenght Volume oil tank approx. 1,300 l SPS controller Telemecanique TSX Micro Operating panel Schneider MAGELIS Touch Baler dimensions built up with hopper 11,750 x 5,000 x 7,105 mm (l x w x h) Transport dimensions only baler 11.750 x 2.500 x 3.450 mm (l x w x h) Machine weight baler approx. 36 tons Comments: The press was partially overhauled and serviced in our workshop and tested and stored after completion of the work. The machine is available at short notice and can be inspected in our warehouse by appointment. The following overhaul work was carried out: Rust removal and partial painting of the press. Remaining hydraulic oil tank drained, oil filter and air filter replaced. New hydraulic oil topped up. All hydraulic hoses replaced. Main hydraulic cylinder, two cylinders of the prepress flap and the cylinder of the press channel dismantled, disassembled, checked, cylinder tubes honed, all seal sets replaced and a final pressure test carried out. Disassembly of the prepress flap with bearings and bearing blocks. 1st and 3rd circular arc segmet cut out and a new one welded in again. Both bearings of the shaft of the prepress flap replaced. Upper material deflector on the frame of the prepress flap replaced. Press ram dismantled, checked and both front rollers replaced. Material deflectors and wear profiles on the sides and base of the press ram cut off and new ones welded in. Horizontal and vertical needle and tying unit dismantled, disassembled, checked, plastic sliding plates, bearings of the drill shafts and wire deflection rollers with bearings in the needle heads replaced. Both bronze slide rails on the left and right in the frame cover to the press ram replaced. Both wire deflection units on the left and right, with bale retaining clamps, completely renewed. Wire insertion unit including hydraulic cylinder under the needle feedthroughs completely renewed. Wire entry marks in the floor and side walls of the bale chamber welded shut and smoothed. General maintenance and service work carried out in accordance with the manufacturer's specifications. Press was tested in manual and automatic mode, accepted and stored after completion of overhaul work. Cjlrovf E Avef Ihcorb We accept no liability for the technical specifications or any errors.

Year of construction: 2001, Condition: excellent (used), Briquetting press for metal chips or granules was only tried on a trial basis Cjlsfb T Huerf Ihcerb hardly run 20 hours of operation 2000 kg/cm2

Condition: new, Year of construction: 2025, Dimensions (L/W/H) 1800x1800x1900 mm Weight 3000 kg Cjlrf Isvz Ex Nehcorb Total power requirement 33,5 kw

Condition: excellent (used), Year of construction: 2016, operating hours: 1,521 h, Functionality: fully functional, HSM V-Press 1160 plus vertical baler, year of manufacture 2016 Technical data: Manufacturer: HSM Type: V-Press 1160 plus Stock no.: 9921 Year of manufacture: 2016 Operating hours: 1521 Pressing force: 55 t Drive power: 4 kW Idle cycle time: 25 s Filling height: 1115 mm Filling opening: 1195 x 650 mm Crjlrf Isv Ni S Nshcob Bale size: 1200 x 1100 x max. 1200 mm Bale weight: 550 kg Dimensions: 1700 x 1800 x 2200 mm (WxDxH) Weight: 2430 kg Materials: paper, cardboard, cardboard, film, plastic, PET The operating instructions and EC Declaration of Conformity are available in German. Remark: The machine is in very good condition. It was checked and tested by us in 28816 Stuhr. You can find the video above with the pictures, or on our website or our Youtube channel. Viewings, also under power, are possible at any time by appointment. On request, we can also carry out tests with your equipment for a fee. We are also happy to answer questions about the machine by telephone from Monday to Thursday from 08:00 to 14:00. On Friday we are there for you from 08.00 to 13.00 h. Please note: All technical data refer to the manufacturer's specifications. We accept no liability for the information provided or for any errors. The offers are non-binding, subject to prior sale and revocable at any time. Viewings are possible by arrangement. The sale is ex works, without guarantee or warranty.

Condition: excellent (used), operating hours: 2,658 h, Functionality: fully functional, pressing force: 71 t, bale weight: 600 kg, filling opening width: 1,000 mm, filling opening length: 1,620 mm, bale height: 720 mm, bale width: 1,100 mm, oil tank capacity: 1,250 l, net weight: 29,000 kg, nominal current: 200 A, Technical data baler: Manufacturer BOA Recycling Systems B.V. Type M75-45-A-5-1.6 Ecoline Year of construction 2021 Hours of operation 2,658 hours (as of May 2024) Number of pressed bales 42,212 pieces (as of May 2024) Press power main press 71,2 kN (71 t) Specific press capacity 9 kg/cm² Operating pressure 280 bar Cylinder stroke 2,200 mm Feed channel 1,620 x 1,000 mm Capacity per cycle time 2,4 m³ Theoretic cycle time 21 seconds Theoretic throughput rate 450 m³/hour Bale size 1,100 x 720 mm, length variably adjustable up to 1,400 mm Driving motor 45 kW Connected load 100 kW Current consumption 200 A Tying system 5-fold vertical, fully automatic, the press stamp is prepared for an additional 3-fold horizontal binding Throughput rate at a bulk weight of 30 kg/cbm approx. 13,6 tons/hour bulk weight of 50 kg/cbm approx. 24,2 tons/hour bulk weight of 100 kg/cbm approx. 36,4 tons/hour bulk weight of 150 kg/cbm approx. 54,7 tons/hour Bale weight up to 600 kg, depends on material Volume hydraulic oil tank 1,250 l SPS controller Siemens S7 1500 Operating panel Siemens SIMATIC HMI TOUCH Cjlrf Ihsu Thcvecerb Transport dimensions of press 10,000 x 2,800 x 3,385 mm (l x w x h) Press height set up with feed chute 4,743 mm Press height with conveyor belt 7,123 mm Machine weight baler approx. 29 tons Noise level <85 dB (A) Condition of the baler: With 2,658 operating hours, the press is almost as good as new and in very good condition, has hardly any signs of wear and is ready for immediate use. Due to larger material input quantities, the pressing force and throughput of the machine no longer meet the customer's current requirements and is therefore being replaced by a new 120 tonne baler. Only the baler is for sale, without conveyor belt and wire drawing stations. Comments: The documentation (Manual, CE, electr./hydr.-drawings), are completely available. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors.

Condition: new, Year of construction: 2025, Dimensions (L/W/H) 1850x1500x1230 mm Weight 870 kg Total power requirement 8 kw Cslrf Ihjvz Eqlscjrb

Condition: excellent (used), Year of construction: 2016, operating hours: 1,924 h, Functionality: fully functional, HSM V-Press 1160 plus vertical baler, year of manufacture 2016 Technical data: Manufacturer: HSM Type: V-Press 1160 plus Stock no.: 9920 Year of manufacture: 2016 Operating hours: 1924 Pressing force: 55 t Drive power: 4 kW Idle cycle time: 25 s Filling height: 1115 mm Filling opening: 1195 x 650 mm Bale size: 1200 x 1100 x max. 1200 mm Bale weight: 550 kg Dimensions: 1700 x 1800 x 2200 mm (WxDxH) Weight: 2430 kg Materials: paper, cardboard, cardboard, film, plastic, PET The operating instructions and EC Declaration of Conformity are available in German. Remark: The machine is in very good condition. It was checked and tested by us in 28816 Stuhr. The video can be found above with the pictures, or on our website or our Youtube channel. Viewings, also under power, are possible at any time by appointment. On request, we can also carry out tests with your equipment for a fee. We are also happy to answer questions about the machine by telephone from Monday to Thursday from 08:00 to 14:00. On Friday we are there for you from 08.00 to 13.00 h. Please note: All technical data refer to the manufacturer's specifications. We accept no liability for the information provided or for any errors. The offers are non-binding, subject to prior sale and revocable at any time. Viewings are possible by arrangement. The sale is ex works, without guarantee or warranty. Crslrf Iev Ni Sishcsb

Condition: good (used), Year of construction: 2019, operating hours: 2,320 h, Functionality: fully functional, pressing force: 60 t, filling opening width: 1,100 mm, filling opening length: 1,400 mm, bale height: 1,100 mm, bale width: 720 mm, overall weight: 12,500 kg, oil tank capacity: 800 l, power: 37 kW (50.31 HP), Technical data baler: Manufacturer Riko Ekos d.o.o Type S-60K (6) Year of construction 2019 Operating hours 2,320 hours, as of August 24 Number of pressed bales 4,359 bales, as of August 24 Pressing force main press 60 tonnes Dimensions of feed chute 1,100 x 1,400 mm Filling volume / pressing cycle 2.1 m³ Bale dimensions 720 x 1,100 mm (W x H), the length is variable Drive power 37 kW Connected load, total 47 kW Tying 4-fold horizontal, fully automatic Cslrf Ihou Thipecsrb Throughput capacity with a bulk density of 30 kg/cbm approx. 5 - 6 tonnes/hour Bulk weight of 50 kg/cbm approx. 9 - 11 tonnes/hour Bulk weight of 100 kg/cbm approx. 15 - 19 tonnes/hour Filling volume of hydraulic oil tank 800 litres PLC control Siemens SIMATIC S7-1200 Siemens SIMATIC HMI control panel Press dimensions assembled without hopper and chute 12,220 x 3,654 x 2,685 mm (L x W x H) Effective transport dimensions excluding press, with dismantled tying system 7,230 x 1,750 x 2,685 mm (L x W x H) Transport weight press 12.5 tonnes Condition of the baler: The machine is part of a sorting line and was only partially used for pressing individual material flows. The machine is now no longer needed and has therefore been sold. However, the baler is regularly put into operation once a week for two to three bales so that the machine remains in working order. Due to the extremely low operating hours, the baler is in good condition and ready for immediate use. Scope of delivery for the baler: 1 piece baler without conveyor belt, hopper and chute 8 pieces wire pulling stations, without wire 1 piece bale chute 1 set of machine documentation Comments: The documentation (Manual, CE-declaration, electr./hydr.-drawings), are completely available. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors.

Condition: new, Year of construction: 2025, Dimensions (L/W/H) 1700x1170x1510 mm Weight 650 kg Crolrsvz Eqfof Ihcjb Total power requirement 6 kw

Condition: good (used), Year of construction: 2016, operating hours: 1,715 h, Functionality: fully functional, HSM V-Press 1160 plus vertical baler, year of manufacture 2016 Technical data: Manufacturer: HSM Type: V-Press 1160 plus Stock no.: 9919 Year of manufacture: 2016 Crjlrsv Ni R Ssf Ihcjb Operating hours: 1715 Pressing force: 55 t Drive power: 4 kW Idle cycle time: 25 s Filling height: 1115 mm Filling opening: 1195 x 650 mm Bale size: 1200 x 1100 x max. 1200 mm Bale weight: 550 kg Dimensions: 1700 x 1800 x 2200 mm (WxDxH) Weight: 2430 kg Materials: paper, cardboard, cardboard, film, plastic, PET The operating instructions and EC Declaration of Conformity are available in German. Remark: The machine is in good condition with slight scratches and dents. It was checked and tested by us in 28816 Stuhr. You can find the video above with the pictures, or on our website or our Youtube channel. Viewings, also under power, are possible at any time by appointment. On request, we can also carry out tests with your equipment for a fee. We are also happy to answer questions about the machine by telephone from Monday to Thursday from 08:00 to 14:00. On Friday we are there for you from 08.00 to 13.00 h. Please note: All technical data refer to the manufacturer's specifications. We accept no liability for the information provided or for any errors. The offers are non-binding, subject to prior sale and revocable at any time. Viewings are possible by arrangement. The sale is ex works, without guarantee or warranty.

Condition: reconditioned (used), Year of construction: 2005, operating hours: 30,408 h, Functionality: fully functional, pressing force: 50 t, bale weight: 550 kg, filling opening width: 1,100 mm, filling opening length: 1,250 mm, bale height: 720 mm, bale width: 1,100 mm, overall weight: 16,000 kg, oil tank capacity: 600 l, year of last overhaul: 2024, Technical data baler: Manufacturer Presona AB Type LP 50 EH1 Year of construction 2005 Operating hours 30,408 hours, as of April Number of pressed bales 198,059 as of April Pressing force main press 50 tonnes Crjlrf Iheu Thhrecjb Specific pressing force 63 N/cm² Theoretical throughput capacity 530 m³/hour Throughput capacity under operating conditions 260 m³/hour Dimensions of feed chute 1,250 x 1,100 mm Bale chamber volume 2.2 m³ Bale dimensions 1,100 x 720 mm, variable length Drive power 22 kW Tying 5-fold vertical, fully automatic Throughput rates with a bulk density of 30 kg/cbm 6 up to 7 tonnes/hour Bulk weight of 50 kg/cbm 7 up to 9 tonnes/hour Bulk weight of 100 kg/cbm 11 up to 14 tonnes/hour Bale density (paper/newspapers) 400 to 550 kg/m³ Hydraulic oil tank capacity 600 litres PLC control Telemecanique TSX Micro Schneider Magelis control panel Effective transport dimensions excl. baler 8,125 x 2,300 x 3,000 mm (L x W x H) Transport weight press approx. 16 tonnes Condition of the baler: The machine was partially overhauled in our workshop and general maintenance work was carried out. After completion of the overhaul work, the press was tested during operation and is available for sale at short notice. Scope of delivery: Only the baler will be sold. The documentation (Manual, CE-declaration, electr./hydr.-drawings), are completely available. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors.

Condition: new, Year of construction: 2025, Dimensions (L/W/H) 2000x1600x1500 mm Weight 1550 kg Total power requirement 11,5 kw Crslrsvz Efvjf Ihceb

Condition: excellent (used), Year of construction: 2016, operating hours: 1,930 h, Functionality: fully functional, HSM V-Press 1160 plus vertical baler, year of manufacture 2016 Technical data: Manufacturer: HSM Type: V-Press 1160 plus Stock no.: 9918 Year of manufacture: 2016 Operating hours: 1930 Pressing force: 55 t Drive power: 4 kW Idle cycle time: 25 s Filling height: 1115 mm Filling opening: 1195 x 650 mm Bale size: 1200 x 1100 x max. 1200 mm Bale weight: 550 kg Dimensions: 1700 x 1800 x 2200 mm (WxDxH) Weight: 2430 kg Materials: paper, cardboard, cardboard, film, plastic, PET Crslrfsv Ni Iqj Ihcob The operating instructions and EC Declaration of Conformity are available in German. Remark: The machine is in very good condition. It was checked and tested by us in 28816 Stuhr. The video can be found above with the pictures, or on our website or our Youtube channel. Viewings, also under power, are possible at any time by appointment. On request, we can also carry out tests with your equipment for a fee. We are also happy to answer questions about the machine by telephone from Monday to Thursday from 08:00 to 14:00. On Friday we are there for you from 08.00 to 13.00 h. Please note: All technical data refer to the manufacturer's specifications. We accept no liability for the information provided or for any errors. The offers are non-binding, subject to prior sale and revocable at any time. Viewings are possible by arrangement. The sale is ex works, without guarantee or warranty.

Condition: excellent (used), Year of construction: 2014, operating hours: 5,059 h, Functionality: fully functional, pressing force: 48 t, bale weight: 550 kg, filling opening width: 1,020 mm, filling opening length: 1,250 mm, total height: 2,800 mm, bale height: 750 mm, bale width: 1,100 mm, overall weight: 12,000 kg, transport height: 2,800 mm, oil tank capacity: 300 l, power: 30 kW (40.79 HP), net weight: 12,000 kg, volume flow: 332 m³/h, nominal current: 59 A, Technical information baler: Manufacturer HSM GmbH + Co. KG Typ VK 4812 Year of construction 2014 Hours of operation 5,059 hours, stand November 2024 Press power main press 48 tons Specific press capacity 58,2 N/cm² Crelrovtpq Hef Ihcsb Feed channel 1,250 x 1,020 mm Theoretic cycle time 11.2 sec. Theoretic throughput rate 332 m³/hour Bale size 1,100 x 750 x 600 up to 1,200 mm Driving motor 30 kW Connected load 32 kW Rated current 59 A Tying system 4-fold horizontal, fully automatic Throughput rate at a bulk weight of 20 kg/cbm up to 6 tons/hour bulk weight of 50 kg/cbm up to 13 tons/hour Bale weight up to 550 kg, depends on material SPS controller Siemens SIMATIC S7-200 Operating panel Siemens HMI Touch Panel Filling quantity hydraulic oil tank 300 L Oil type HVI 46 Machine installation dimensions with bale chute 10,046 x 4,387 x 2,705 mm (l x w x h) Transport dimensions baler 8,500 x 2,500 x 2,750 mm (l x w x h) Machine weight press approx. 12 t Scope of delivery: Baler HSM VK 4812, without hydraulic oil, without conveyor system. Two wire reel boxes for 8 pieces 40 kg wire reels, without wire Bale chute Machine documentation in German Comments: The press is equipped with an oil cooler and potential-free contacts for external control. The control cabinet is operated from the left in the direction of pressing, the needle unit is located on the right-hand side and can be folded back for transport. The press is in good condition, is currently still in operation and is used in a distribution warehouse for film compaction. In the 14th calendar week, the baler will be dismantled and replaced with a new, larger machine and will then be available for loading. A truck with an effective internal height of 2,800 mm is required to transport the baler. The press is loaded without hydraulic oil. The conveyor technology shown in the photos is not for sale and is not included in the scope of delivery. The documentation (operating instructions, CE declaration, electrical/hydraulic circuit diagrams) is available in German. Viewing is possible by appointment. We accept no liability for the technical details or any errors.

Condition: good (used), Year of construction: 2016, operating hours: 1,509 h, Functionality: fully functional, HSM V-Press 1160 plus vertical baler, year of manufacture 2016 Technical data: Manufacturer: HSM Type: V-Press 1160 plus Stock no.: 9917 Year of manufacture: 2016 Operating hours: 1509 Pressing force: 55 t Drive power: 4 kW Idle cycle time: 25 s Filling height: 1115 mm Filling opening: 1195 x 650 mm Bale size: 1200 x 1100 x max. 1200 mm Bale weight: 550 kg Dimensions: 1700 x 1800 x 2200 mm (WxDxH) Weight: 2430 kg Materials: paper, cardboard, cardboard, film, plastic, PET The operating instructions and EC Declaration of Conformity are available in German. Remark: The machine is in good condition with slight scratches and dents. It was checked and tested by us in 28816 Stuhr. You can find the video above with the pictures, or on our website or our Youtube channel. Viewings, also under power, are possible at any time by appointment. On request, we can also carry out tests with your equipment for a fee. Cslrsv Ni Idof Ihcerb We are also happy to answer questions about the machine by telephone from Monday to Thursday from 08:00 to 14:00. On Friday we are there for you from 08.00 to 13.00 h. Please note: All technical data refer to the manufacturer's specifications. We accept no liability for the information provided or for any errors. The offers are non-binding, subject to prior sale and revocable at any time. Viewings are possible by arrangement. The sale is ex works, without guarantee or warranty.

Condition: good (used), Year of construction: 2015, operating hours: 19,173 h, Functionality: fully functional, pressing force: 150 t, filling opening width: 1,100 mm, filling opening length: 2,000 mm, bale height: 750 mm, bale width: 1,100 mm, overall weight: 35,800 kg, oil tank capacity: 4,300 l, Technical data baler: Manufacturer Europress Umwelttechnik GmbH, Germany Type EP5 150 V5 Year of construction 2015 Operating hours 19,173 hours Number of pressed bales 282,961 bales Number of press strokes from the press ram 1,895,112 press strokes Pressing force of main press 150 t Specific pressing force 181.8 N/cm² Dimensions of feed chute 1,000 x 2,000 mm (w x l) Cslreu Thfdof Ihcsrb Bale dimensions 750 x 1,100 mm (h x w), length variable Drive power 2 x 55 kW + 15 kW + 2 x 0.75 kW Rated current 230 A Cable cross-section supply 120 mm² Tying 5-fold vertical, fully automatic Hydraulic oil tank capacity 4,300 l PLC control Siemens S7 / ET200S Transport weight press 35,800 kg Special equipment: Base plates and side walls made of HARDOX steel Free tamper in front of the counter blade, with cleaning cycle Scope of delivery: 1 piece baler 1 piece control cabinet 1 set of oil collecting pans under the baler 1 piece maintenance platform on the baling channel 1 piece Feed hopper 1 piece Drop chute 10 pieces wire reel stands 2 pieces wire drawing stations with deflection rollers 1 set of machine documentation (operating instructions, electrical circuit diagram, hydraulic circuit diagram, CE confirmation) Remarks: The machine is still completely assembled and available at short notice. Dismantling and loading is the responsibility of the buyer. The documentation (operating instructions, electrical circuit diagram, hydraulic circuit diagram, CE confirmation declaration) is available in German. An inspection is possible by arrangement. We do not assume any liability for the technical data and possible errors.

Condition: excellent (used), Year of construction: 2016, operating hours: 1,940 h, Functionality: fully functional, HSM V-Press 1160 plus vertical baler, year of manufacture 2016 Technical data: Manufacturer: HSM Type: V-Press 1160 plus Stock no.: 9916 Year of manufacture: 2016 Operating hours: 1940 Pressing force: 55 t Drive power: 4 kW Idle cycle time: 25 s Filling height: 1115 mm Filling opening: 1195 x 650 mm Bale size: 1200 x 1100 x max. 1200 mm Bale weight: 550 kg Dimensions: 1700 x 1800 x 2200 mm (WxDxH) Weight: 2430 kg Materials: paper, cardboard, cardboard, film, plastic, PET The operating instructions and EC Declaration of Conformity are available in German. Colrf Ihev Ni D Sjcjrb Remark: The machine is in very good condition. It was checked and tested by us in 28816 Stuhr. The video can be found above with the pictures, or on our website or our Youtube channel. Viewings, also under power, are possible at any time by appointment. On request, we can also carry out tests with your equipment for a fee. We are also happy to answer questions about the machine by telephone from Monday to Thursday from 08:00 to 14:00. On Friday we are there for you from 08.00 to 13.00 h. Please note: All technical data refer to the manufacturer's specifications. We accept no liability for the information provided or for any errors. The offers are non-binding, subject to prior sale and revocable at any time. Viewings are possible by arrangement. The sale is ex works, without guarantee or warranty.

Condition: good (used), Year of construction: 2010, operating hours: 3,641 h, Functionality: limited functionality, pressing force: 36 t, filling opening width: 1,100 mm, filling opening length: 1,080 mm, bale height: 750 mm, bale width: 1,100 mm, power: 15 kW (20.39 HP), net weight: 4,000 kg, volume flow: 90 m³/h, Technical data baler: Manufacturer Presto GmbH & Co. KG Typ CC 36 M Year of construction 2010 Hours of operation 3,641 h Press power main press 36 t Specific press capacity 467 N/cm² Feed channel 1.080 x 1100 mm (l x w) Cycle time 34 sec. Capacity per cycle time 0,85 m³ Theoretic throughput rate 90 m³/h Throughput rate under operating conditions with a material bulk density of 35 kg/m³ approx. 51 m³/hour Bale size 1100 x 750 mm (w x h), length variable Driving motor 15 kW Tying 4-fold vertical, semi-automatic, with polyester synthetic yarn Throughput rate at a bulk weight of 35 kg/cbm 1,8 to/h bulk weight of 60 kg/cbm 2,5 to/h Cslrf Iou Thh Eshcjrb bulk weight of 100 kg/cbm 3,1 to/h Transport dimensions only baler 4.200 x 1.640 x 2.200 mm Machine weight baler approx. 4 to Comments: The press was checked for function in our workshop, then stored and is therefore available at short notice. The machine documentation (operating ins3.641tructions, CE, electrical and hydraulic circuit diagram) is available. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors.

Condition: reconditioned (used), Year of construction: 1996, Functionality: fully functional, pressing force: 170 t, filling opening width: 1,020 mm, filling opening length: 1,800 mm, bale height: 1,100 mm, bale width: 1,100 mm, overall weight: 40,000 kg, oil tank capacity: 3,000 l, year of last overhaul: 2024, For sale is a used baling press system consisting of a chain belt conveyor for underfloor operation, with a feed hopper, a hydraulic pre-compactor with whirlulator, a MACPRESSE 111A baling press, two complete wire drawing frames with 5 wire reel stands each, without wire. Technical data baler: Manufacturer MACPRESSE EUROPA S.R.L. Typ 111A Year of construction 1996, refurbished in 10/2024 Press power main press 170 tons Specific press capacity 14 kg/cm² Celou Th D Rsrf Ihcsrb Feed channel 1,800 x 1,020 mm Filling volume 2,5 cm³ Theoretic throughput rate 750 m³/h Bale size 1,100 x 1,100 mm, length variable Driving motor 2 x 55 kW Tying system 5-fold horizontal, full automatic Throughput rate at a approx. 30 up to 35 tons/h, depends on material Volume hydraulic oil tank 3,000 l Transport dimensions of press with new machine feets 113,700 x 2,300 x 2,900 mm (l x w x h) Machine weight baler approx. 40 tons Comments: The baler was partially overhauled in our workshop and tested after completion of the work, please look at our functional video. The system was previously used to bale paper and cardboard from municipal collections. The contract was awarded elsewhere after the end of the contract period, so the complete system is for sale. The overhaul work carried out and the spare parts replaced can be found in the detailed photo documentation and in our quotation. The documentation (Manual, CE, electr./hydr.-drawings), are completely available. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors. Technical data conveyor belt: Manufacturer Wagensfeld B.V. Type chain belt conveyor 1700 mm Year of construction 2017 Drive power 7.5 kW Belt speed 14 m/minute Length of infeed conveyor 6,900 mm Length of ascending belt 12,885 mm Length of gooseneck 1,747 mm Overall length 21,271 mm Pitch 32° Effective width 1,644 mm Height of drive shaft above ground 5,777 mm Wall height of feed conveyor 500 mm Wall height of ascending conveyor 880 mm Steel flights height 40 mm Distance between flights 1200 mm Transport dimensions conveyor disassembled 15,005 x 2,503 x 2,435 mm (l x w x h) Pit dimensions 11,500 x 2,700 x 1,015 mm (l x w x d) Remarks: The chain belt conveyor, built in 2017, was later made to fit the baler during the last installation of the baler in the Netherlands and is newly installed. The conveyor belt is in good, operational condition and has therefore not been overhauled. An installation drawing with the pit dimensions is available. Scope of delifery: 1 chain belt conveyor, Wagensveld B.V. 1 piece feed hopper with pre-compressor flaps 1 piece wirbulator 1 baler MACPRESSE, type 111A 2 wire drawing frames with wire reel stands, without wire 1 operating manual with CE declaration, electrical and hydraulic circuit diagram

Condition: good (used), Year of construction: 1994, operating hours: 51,551 h, Functionality: fully functional, pressing force: 78 t, bale weight: 850 kg, filling opening width: 1,100 mm, filling opening length: 1,500 mm, bale height: 720 mm, bale width: 1,100 mm, overall weight: 24,000 kg, oil tank capacity: 900 l, A complete baling system is for sale, consisting of a conveyor belt with feed hopper, the baling press with bale chute and wire pulling stations, without wire. Technical data baler: Manufacturer Bollegraaf Recycling Machinery B.V. Type HBC 80 AF Year of construction 1994, overhauled by the manufacturer Bollegraaf 2003 Operating hours 51,551 hours, as of December 2024 Number of pressed bales 613,446 pieces, as of December 2024 Main press pressing force 78 tonnes Pre-press pressing force 45 tonnes Dimensions of feed chute 1,500 x 1,100 mm (l x w) Crjlrf Ihjvf E Dasceb Filling volume / pressing cycle 2.9 m³ Theoretical cycle time 22 seconds Throughput capacity under operating conditions 300 - 450 m³/hour Bale dimensions 1,100 x 720 mm (w x h), the length is variable Drive power 45 kW Connected load, total 60 kW Tying 5-fold vertical, fully automatic Throughput capacity with a bulk density of 30 kg/cbm approx. 10 tonnes/hour Bulk weight of 50 kg/cbm approx. 18 tonnes/hour Bulk weight of 100 kg/cbm approx. 30 tonnes/hour Throughput in whirling mode approx. 20 tonnes/hour Bale weights with a bale length of approx. 1.2 m approx. 550 - 850 kg Hydraulic oil tank capacity 900 litres SPS control manufacturer Schneider Electric Transport weight of baler approx. 24 tonnes Accessories: Conveyor belt with feed chute, bale chute and wire pulling stations Condition of the baler: The machine was completely overhauled by the manufacturer Bollegraaf in 2003 and later fitted with a new PLC control system from Schneider Electric. The baler was used to compress dried grass into bales. Despite its age, the entire system, including the conveyor belt, is in really good condition and has been regularly serviced. The system is still fully assembled, connected to the power supply and can be inspected during operation without the use of materials. Scope of delivery for the baler: Baling press with conveyor belt, feed hopper, wire drawing stations and bale chute. Comments: Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors.

Condition: good (used), Year of construction: 2019, operating hours: 673 h, Functionality: fully functional, pressing force: 60 t, filling opening width: 1,100 mm, filling opening length: 1,400 mm, bale height: 1,100 mm, bale width: 720 mm, overall weight: 12,500 kg, oil tank capacity: 800 l, power: 37 kW (50.31 HP), Technical data baler: Manufacturer Riko Ekos d.o.o Type S-60K (5) Year of construction 2019 Operating hours 673 hours, as of August 24 Number of pressed bales 1,127 bales, as of August 24 Pressing force main press 60 tonnes Dimensions of feed chute 1,100 x 1,400 mm Filling volume / pressing cycle 2.1 m³ Bale dimensions 720 x 1,100 mm (W x H), the length is variable Drive power 37 kW Connected load, total 47 kW Tying 4-fold horizontal, fully automatic Throughput capacity with a bulk density of 30 kg/cbm approx. 5 - 6 tonnes/hour Bulk weight of 50 kg/cbm approx. 9 - 11 tonnes/hour Bulk weight of 100 kg/cbm approx. 15 - 19 tonnes/hour Filling volume of hydraulic oil tank 800 litres PLC control Siemens SIMATIC S7-1200 Siemens SIMATIC HMI control panel Press dimensions assembled without hopper and chute 12,220 x 3,654 x 2,685 mm (L x W x H) Effective transport dimensions excluding press, with dismantled tying system 7,230 x 1,750 x 2,685 mm (L x W x H) Transport weight press 12.5 tonnes Condition of the baler: The machine is part of a sorting line and was only partially used for pressing individual material flows. The machine is now no longer needed and has therefore been sold. However, the baler is regularly put into operation once a week for two to three bales so that the machine remains in working order. Due to the extremely low operating hours, the baler is in good condition and ready for immediate use. Scope of delivery for the baler: 1 piece baler without conveyor belt, hopper and chute 8 pieces wire pulling stations, without wire 1 piece bale chute 1 set of machine documentation Comments: Crolrfju Thicj Ihcjb The documentation (Manual, CE-declaration, electr./hydr.-drawings), are completely available. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors.

Condition: excellent (used), Year of construction: 2012, operating hours: 18,593 h, Functionality: fully functional, pressing force: 140 t, bale weight: 1,300 kg, filling opening width: 1,100 mm, filling opening length: 1,600 mm, bale height: 1,100 mm, bale width: 1,100 mm, overall weight: 47,000 kg, nominal current: 470 A, Technical data baler: Manufacturer Bollegraaf Typ HBC 140 K Cslrf Ieu Thy Eohcerb Year of construction 2012 Working hours 18.593 hours, stand September 2024 Press power main press 140 tons Press power of pre-press 70 tons Feed channel 1,600 x 1,100 mm Capacity per cycle time 4,34 m³ Theoretic cycle time 16 sec. Bale size 1,100 x 1,100 mm Driving motor 2 x 75 kW Connected load 248 kW Full load current 470 A Tying system 5-fold vertical, fully automated Throughput rate at a bulk weight of 30 kg/cbm approx. 30 tons/h bulk weight of 50 kg/cbm approx. 46 tons/h bulk weight of 100 kg/cbm approx. 82 tons/h Bale weight 800 up to 1300 kg, depends on material and bale lenght SPS controller Telemecanique TSX Micro Operating panel Schneider MAGELIS Touch Baler dimensions built up with hopper 13,200 x 2,750 x 7,344 mm (l x w x h) Transport dimensions only baler 13.200 x 2.750 x 3.450 mm (l x w x h) Machine weight baler approx. 47 tons Special equipment: 2-flap pre-compressor for large cardboard boxes and octatainers Wirbulator for magazines and books Comments: The press is currently in operation and is to be replaced by a new machine in the second calendar week of 2025. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors.

Condition: excellent (used), Year of construction: 2009, operating hours: 20,536 h, Functionality: fully functional, pressing force: 80 t, bale weight: 600 kg, filling opening width: 1,100 mm, filling opening length: 1,400 mm, bale height: 750 mm, bale width: 1,100 mm, net weight: 16,000 kg, nominal current: 75 A, Technical data baler: Manufacturer Avermann Maschinenfabrik GmbH & Co. KG, Germany Type AVOS 1410-45/80 Year of construction 2009 Operation hours 20,536 hours, as of September 2024 Press power main press 80kN Specific press force 103,9 N/cm² Feed channel 1,400 x 1,000 mm Theoretic cycle time 12 sec Theoretic throughput capacity 300 m³/h Bale size 1,100 x 750 (w x h), the length is variable Drive power 45 kW Connected load 75 kW Tying system 4-fold, vertical, fully automatic Throughput capacity at a bulk weight of 30 kg/cbm approx. 6,0 t/h bulk weight of 50 kg/cbm approx. 10,5 t/h bulk weight of 100 kg/cbm approx. 17,5 t/h Bale weight with a bale length of approx. 1.2 m up to 600 kg, depends on material SPS controller Siemens S7-300 Operating panel pulsotronic Baler dimensions built up 8,610 x 2,400 x 3,835 mm (l x w x h) Transport weight baler approx. 16 t Special equipment: Wear-resistant floor made of HARDOX steel Special press ram for pressing ‘difficult’ materials and loose bulk materials with small grain sizes Control cabinet air conditioning Machine foot elevation 200 mm Crelrf Iou Thypehcsb Remark: Due to a reorganisation of the manufacturing processes within the company, a new baling line is being built in a new hall. The old baling press with conveyor technology is therefore no longer required and is expected to be available for sale at the beginning of 2025. Technical data for the chain belt conveyor: Manufacturer not known Type not known Length of feed belt 5,300 mm Length of ascending belt 12,700 mm Overall height 7,300 mm Useful width 1,200 mm Unfortunately, no further technical data, documentation or drawings are available. Condition of the press system: The entire system is in very good condition and is regularly cleaned and maintained by the operator. The quality of the bales is exceptionally good, as you can see from the photos of the pressed bale goods. Even hard plastics such as plastic crates, PP bucket chains and PE plastic drums were pressed into dimensionally stable bales with the fourfold vertical binding. Tidiness, cleanliness and maintenance of the systems are practised in this company and not just written on the website. Scope of delivery: Avermann baler, type AVOS 1410-45/80, incl. wire drawing stations and bale chute Avermann conveyor belt, type KGF GB 1500 Comments: The documentation (operating instructions, CE declaration, electrical/hydraulic circuit diagram) for the press is available in full. Unfortunately, there is no more documentation for the conveyor belt. Viewing is possible by appointment. We accept no liability for the technical details or any errors.

Condition: excellent (used), Year of construction: 2023, operating hours: 1,851 h, Functionality: fully functional, pressing force: 70 t, bale weight: 500 kg, filling opening width: 1,100 mm, filling opening length: 1,400 mm, bale height: 750 mm, bale width: 1,100 mm, overall weight: 17,000 kg, oil tank capacity: 70 l, Technical data baler: Manufacturer Avermann Maschinenfabrik GmbH & Co. KG, Germany Type AVOS 1410 BS-22/50 Year of construction 2023 Pump operation hours 1,851 hours, as of July 24 Press power main press 70 t (a 70 tonne hydraulic cylinder is installed, special equipment) Specific press force 90,9 N/cm² (a 70 tonne hydraulic cylinder is installed, special equipment) Feed channel 1,400 x 1,000 mm Theoretic cycle time 13 sec Theoretic throughput capacity 266 m³/h Bale size 1,100 x 750 (w x h), the length is variable Drive power 22 kW Connected load 65 kW Tying system 4-fold, vertical, fully automatic Throughput capacity at a bulk weight of 30 kg/cbm approx. 5,5 t/h bulk weight of 50 kg/cbm approx. 7,5 t/h bulk weight of 100 kg/cbm approx. 9,7 t/h Bale weight with a bale length of approx. 1.2 m up to 500 kg, depends on material SPS controller Siemens S7-1500 Operating panel Schneider Harmony Baler dimensions built up 8,610 x 2,400 x 3,835 mm (l x w x h) Transport weight baler approx. 17 t Special equipment: Wear-resistant floor made of HARDOX steel Larger main hydraulic cylinder with 70 tonnes of pressing force Special press ram for pressing loose bulk materials with small grain sizes OptiCut XS system for lower cutting forces and higher throughput rates Special pressing piston for pressing "difficult" materials Technical data for the conveyor belt: Manufacturer Avermann Maschinenfabrik GmbH & Co. KG, Deutschland Type KGF GB 1500 Year of construction 2023 Drive power 4.0 kW Belt speed approx. 0.3 m/second Length feeding conveyor 2,679 mm Length elevating conveyor 6,866 mm Crjlsu Thbxerf Ihcjb Length goose neck 1,272 mm Grade 35° Effecting width 1,400 mm Side wall height 800 mm Carrier height 50 mm Carrier distance 750 mm Belt quality EP 400/3, 3:1 (DIN quality N) Overall height 4,515 mm Overall transport dimensions11,148 x 2,502 mm (l x w) Technical data on the non-contact personal protection system: Manufacturer BOREMA Umwelttechnik AG, Switzerland Type APSS iBOR 22 Year of construction 2023 Condition of the press system: The entire system is in very good condition due to the short operating time of only 1,851 pump hours and the processing of only paper, cardboard and film. Scope of delivery: Avermann baler, type AVOS 1410 BS-22/50, incl. wire drawing stations and bale chute Avermann conveyor belt, type KGF GB 1500 BOREMA personal protection system, type APSS iBOR 22 Comments: The documentation (Manual, CE-declaration, electr./hydr.-drawings), are completely available. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors.

Condition: excellent (used), Year of construction: 2022, Functionality: fully functional, Technical data on the EPS (Polystyrene) press: Manufacturer FZ-Recycling GmbH & Co. KG, Germany Type FZR 320 Year of construction 12/2022 Drive power shredder 4 kW Crelreu Thkajf Ihceb Drive power of compactor screw 7.5 kW Drive power hydraulic unit for the holding clamp in the press channel 1.1 kW Total connected load 12.6 kW Current consumption 32 A Compaction ratio of the compacted blocks to the original product approx. 50:1 (depending on material) Block weight after compaction approx. 300kg/m³ (depending on material) Block dimensions 320 x 320 mm, variable length Throughput approx. 100 kg/hour, depending on material Achievable density approx. 250 - 300 kg/m³ The pressed blocks are stacked approx. 1400 mm high on pallets and stretch-wrapped. Machine dimensions approx. 4,600 x 1,400 x 1,980 mm (l x w x h) Transport weight press 1,325 kg Condition of the baler: The press was only used sporadically, is in very good condition and available at short notice. Due to the low weight of the machine and the forklift shoes in the transport frame, the press is mobile and can be used directly on the construction site where the material is produced. The electrical connection is made via a CEE 32 A plug. Scope of delivery for the baler: 1 piece EPS press, ready for connection and use Comments: The documentation (Manual, CE-declaration, electr./hydr.-drawings), are completely available. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors.