Condition: used, Year of construction: 2011, operating hours: 5,000 h, machine/vehicle number: M344Z16201031AHC, travel distance X-axis: 2,032 mm, travel distance Y-axis: 660 mm, travel distance Z-axis: 610 mm, table load: 2,700 kg, spindle speed (max.): 12,000 rpm, The following repairs were carried out: Defective inverter identified and replaced Bearings in the Y-axis replaced; bearing set VTXZ Y-axis (5 pieces, 35x72) Rotary table adjusted Orientation adjusted TECHNICAL DETAILS Travel range X-axis: 2,032 mm Travel range Y-axis: 660 mm Travel range Z-axis: 610 mm Spindle speed: 12,000 rpm Spindle cooling: Internal cooling Rapid traverse rate X/Y/Z: 35 m/min Power: 18 kW Tool holder: SK 40 Tool positions: 40 Tool diameter with full occupancy: 75 mm Maximum tool weight: 10 kg Maximum tool length: 300 mm Hjdpjzka Hiefx Apnsfi Table load: 2,700 kg Table clamping area: 2,285 x 660 mm T-slots in the table according to DIN 650: 5 Slot width: 18 mm H8 Slot spacing: 125 mm Positional accuracy X, Y, Z: 0.02 mm Repeatability X, Y, Z: 0.01 mm MACHINE DETAILS Footprint W x D x H, doors open / with control / chip conveyor: 6,950 x 5,150 x 3,700 mm Transport weight: 20,000 kg Machine weight: 18,000 kg Operating hours Machine hours: 11,417 hours Spindle hours: approx. 5,000 hours Further technical data can be found in the attached documents.

Condition: used, Year of construction: 2004, operating hours: 28,082 h, travel distance X-axis: 800 mm, travel distance Y-axis: 620 mm, travel distance Z-axis: 520 mm, controller model: Siemens 840 D, spindle speed (max.): 13,000 rpm, The control system (PCU 50) was replaced in March 2024! The machine spindle was replaced after approximately 5,500 operating hours! TECHNICAL DETAILS Travel range X-axis: 800 mm Travel range Y-axis: 620 mm Travel range Z-axis: 520 mm Spindle speed: 13,000 rpm Number of tool slots in the tool magazine: 30 MACHINE DETAILS Control system: Siemens 840 D Operating hours Control system operating hours: 60,150 h Machine operating hours: 56,860 h Spindle operating hours: 28,082 h Spindle replacement at: 5,500 h Hfsdpozka Akefx Apnoi EQUIPMENT Tools 4th axis Hofmann RW/NC160 Oil mist extraction system Strip filter system with internal cooling, 20 bar, with dual switching filter Documentation: Hedelius + Siemens Sinumerik Infrared probe: Renishaw

Condition: used, Year of construction: 2005, machine/vehicle number: 107.32.99.158, travel distance X-axis: 530 mm, travel distance Y-axis: 450 mm, travel distance Z-axis: 450 mm, controller model: Heidenhain iTNC 530, spindle speed (max.): 12,000 rpm, Re-auction due to buyer’s payment default! The machine spindle was replaced in July 2025! TECHNICAL DETAILS Travel range X-axis: 530 mm Travel range Y-axis: 450 mm Travel range Z-axis: 450 mm Rotary table Table diameter: 400 mm Table load capacity: 200 kg Swivel range: degrees Swivel speed: 20 rpm Rotational speed: 30 rpm Tool holder: SK40 Maximum speed: 12,000 rpm Recommended maximum working feed rate: 15 m/min Rapid traverse speed: 22 m/min Feed force X and Y/Z: 5,000 N Magazine capacity: 30 Maximum tool diameter: 90 mm Maximum tool length: 250 mm (manual 350 mm) Maximum tool weight: 6 kg MACHINE DETAILS Control system: Heidenhain iTNC 530 with digital control Positional tolerance according to DIN/ISO 230-2/97: 0.008 mm Machine weight: 6,500 kg Hfedeziz Ncspfx Apnei EQUIPMENT RENISHAW MP 12 measuring probe Blum tool monitoring system

Condition: ready for operation (used), Year of construction: 2023, functionality: fully functional, machine/vehicle number: PR721523001, travel distance X-axis: 1,300 mm, travel distance Y-axis: 650 mm, travel distance Z-axis: 600 mm, controller model: Heidenhain TNC-460, spindle speed (max.): 15,000 rpm, The new price of the machine was approximately €140,000 in 2023! No tools or a vise are included. However, these can be purchased separately upon request. TECHNICAL DETAILS Travel range X-axis: 1,300 mm Travel range Y-axis: 650 mm Travel range Z-axis: 600 mm Spindle speed: 15,000 rpm Main spindle servo motor Siemens: 20/53 kW Main spindle servo motor Fanuc: 15/30 kW Spindle taper: SK 40 Work table Table dimensions: 1,500 × 650 mm Table load: max. 1,200 kg T-slots: 18 × 5 × 100 mm Distance spindle to table surface: 150–750 mm Distance spindle center to Z-axis cover: 697 mm Rapid traverse X/Y axis: 36 m/min Rapid traverse Z axis: 36 m/min Working feed rate: max. 1–12,000 mm/min Feed motors X/Y/Z: 3.2/3.2/4.3 kW Torques of the feed motors X/Y/Z: 20/20/27 Nm Tool positions: 28 Tool length: max. 300 mm Tool diameter: max. 75 mm Tool diameter with free auxiliary positions: max. 125 mm Tool weight: max. 8 kg Tool change time: 1.6 s MACHINE DETAILS Control system: Heidenhain TNC-460 Accuracy without linear glass scales Positioning accuracy over the entire travel range: 0.012 mm Repeatability accuracy over the entire travel range: 0.008 mm Accuracy with linear glass scales Positioning accuracy over the entire travel range: 0.008 mm Repeatability accuracy over the entire travel range: 0.006 mm Cooling and power supply Coolant tank volume: 250 l Coolant flow rate: 40 l/min Hsdpfx Apozlh S Aonsfi Mains voltage: 400 V ± 10 % Number of phases: 3 Mains frequency: 50 Hz Connected power: 85 kVA Dimensions and weight Dimensions (L × W × H): 4,025 × 3,090 × 3,185 mm Weight: 8,000 kg EQUIPMENT Direct drive Double-arm tool changer O-BLUM tool measuring system Lasercontrol NT O-BLUM workpiece measuring system TC50 Electronic handwheel (MPG) Thread drilling without compensation chuck USB interface CF card interface Ethernet interface HIWIN linear guides with roller guides in all axes HIWIN ball screws Directly driven main spindle NSK/FAG main spindle bearings Separate oil-air spindle cooling unit Fully enclosed tool changer for protection against chips Pneumatic intermediate tank for the tool changer as a backup in case of pressure drop Fully enclosed splash guard Separate air conditioning system for heat dissipation from the control cabinet Siemens electrical components Automatic, path- or time-controlled central lubrication system Kyarow telescopic covers in all axes Coolant system with adjustable nozzles as a coolant ring around the spindle Chip flushing system in the interior for optimal chip collection Spiral chip conveyor working in the Y-direction for removing chips from the machining area Rear chain chip conveyor

Condition: ready for operation (used), Year of construction: 2005, functionality: fully functional, travel distance X-axis: 2,000 mm, travel distance Y-axis: 500 mm, travel distance Z-axis: 550 mm, table length: 2,600 mm, spindle speed (max.): 12,000 rpm, No minimum price – guaranteed sale to the highest bidder! TECHNICAL DETAILS Travel range, X-axis: 2,000 mm Travel range, Y-axis: 500 mm Travel range, Z-axis: 550 mm C-axis rotation: 360° Table length: 2,600 mm Table width: 550 mm Tool holder: ISO40 Main spindle power: 22 kW Spindle speed: 20 - 12,000 rpm Positioning accuracy: 0.01 mm Travel speed: 667 mm/s Number of axes: 4 MACHINE DETAILS Control system manufacturer: Siemens Hfedpezk Dv Ujfx Apnoi Power consumption: 24 kW Dimensions & Weight Dimensions (L x W x H): 7,500 x 3,700 x 2,500 mm Net weight: 9,600 kg Shipping packages: 2 EQUIPMENT Tool magazine External cooling Chip conveyor CE marking

Condition: ready for operation (used), Year of construction: 2002, functionality: fully functional, machine/vehicle number: 008078, travel distance X-axis: 850 mm, travel distance Y-axis: 550 mm, travel distance Z-axis: 630 mm, controller model: Fanuc O-M, rotational speed (max.): 8,000 rpm, TECHNICAL DETAILS Travel range, X-axis: 850 mm Travel range, Y-axis: 550 mm Travel range, Z-axis: 630 mm Spindle mount: ISO40 Speed: 8,000 rpm Table surface area: 1,000 x 540 mm MACHINE DETAILS Control system: Fanuc O-M Tool changer magazine positions: 24 Hfjdpfx Ajzi D Rpopnei Weight: 5,500 kg EQUIPMENT Electric handwheel Chip tray

Condition: ready for operation (used), Year of construction: 1997, functionality: fully functional, travel distance X-axis: 1,000 mm, travel distance Y-axis: 750 mm, travel distance Z-axis: 750 mm, controller model: Heidenhain TNC426, rotational speed (max.): 12,000 rpm, No minimum price – guaranteed sale to the highest bidder! TECHNICAL DETAILS Travel range, X-axis: 1,000 mm Travel range, Y-axis: 750 mm Travel range, Z-axis: 750 mm Table size: 1,150 x 700 mm Hfjdpfxjzi D Rce Apnsi Tool shank: SK40 Spindle speed range: 12,000 rpm MACHINE DETAILS Control system: Heidenhain TNC426 Machine weight approx.: 10,500 kg EQUIPMENT 30-position tool changer Electronic handwheel Chip conveyor Coolant system

Condition: ready for operation (used), Year of construction: 1997, functionality: fully functional, machine/vehicle number: 179, travel distance X-axis: 510 mm, travel distance Y-axis: 510 mm, travel distance Z-axis: 510 mm, controller model: MSC 803, rotational speed (max.): 8,000 rpm, No minimum price – guaranteed sale to the highest bidder! TECHNICAL DETAILS Travel range, X-axis: 510 mm Travel range, Y-axis: 510 mm Travel range, Z-axis: 510 mm Table size: 750 x 550 mm Spindle speed range: 8,000 rpm Spindle mounting: BT40 Hedpfxezi D E Ts Apnjfi MACHINE DETAILS Control system: MSC 803 Weight: 4,500 kg EQUIPMENT 25-position tool changer Coolant system

Condition: ready for operation (used), Year of construction: 2015, functionality: fully functional, travel distance X-axis: 600 mm, travel distance Y-axis: 400 mm, travel distance Z-axis: 500 mm, controller model: Mitsubishi M70, spindle speed (max.): 12,000 rpm, TECHNICAL DETAILS Travel range, X-axis: 600 mm Travel range, Y-axis: 400 mm Travel range, Z-axis: 500 mm Spindle mounting: SK40 Spindle speed: 12,000 rpm Spindle drive power: 7.5 kW Table clamping area: 2x 700x400 mm MACHINE DETAILS Control system: Mitsubishi M70 Tool changer magazine slots: 24 Weight: 6,600 kg EQUIPMENT Pallet changer Hodpfszi D Emex Apnjfi 4th axis (rotary table) 24-tool automatic tool changer IKZ (integrated coolant supply) Chip conveyor

Condition: ready for operation (used), Year of construction: 2004, operating hours: 77,374 h, functionality: fully functional, machine/vehicle number: 419-01, travel distance X-axis: 6,000 mm, travel distance Y-axis: 630 mm, controller model: Siemens 840D, spindle speed (max.): 12,000 rpm, The machine spindle was replaced in 2021 (spindle operating hours approx. 7,300 h)! The machine underwent a general overhaul in 2013! The machine has been continuously maintained and repaired annually by the manufacturer, and kept up to date with the latest technology (preventive maintenance). The last maintenance was carried out in January 2024. TECHNICAL DETAILS Travel distance X-axis: 6,000 mm Travel distance Y-axis: 630 mm Hfodpjzlnm Hsfx Apnji Spindle speed: 12,000 rpm Spindle torque: 140 Nm Rapid traverse rate in X/Y/Z: 60 m/min Chip-to-chip time vertical: 3.0 sec. (3.3 sec. DIN) Chip-to-chip time horizontal: 4.7 sec. (5.0 sec. DIN) MACHINE DETAILS Control system: Siemens 840D Type of power supply: 3/N/PE Mains frequency: 50/60 Hz Operating voltage: 400 V Control voltage: 220/24 V Connected load: 52 kVA Rated current: 75 A Fuse rating: 80 A Weight: 19,500 kg Operating hours: 77,374 h EQUIPMENT 5-axis milling package Scraper belt conveyor, discharge height: 1,050 mm Coolant-through-spindle (CTS) preparation Vacuum rotary filter KNOLL VRF250 (steel, cast iron, aluminum, plastic, brass) High pressure 70 bar with HD pump and variable valve Cooling nozzle per oscillating table Emulsion mist extraction, 2 extraction fans at 800 m³/h each Rotating viewing window on the left and right (1,400 mm from the center of the machine) Automatic loading doors Center partition for oscillating machining 92 tool positions HSK-A63 (rear magazine) Compressed air blow Tool life monitoring Additional V24 RS232 in the control cabinet BDE/MDE interface (status: machine on, machine running, piece counter) Marposs (Brankamp) collision monitoring CMS100 3D machine model for kinematic simulation in the CAM programming system Hydraulic unit 210 bar, 2 clamping circuits, separate system clamping pressure per oscillating table, clamping pressure control Linear clamping system KOHN 8 hydraulic clamping blocks KOHN Multi 2000 MFS 125/680 HD Two-part grating platform for the operator across the entire operating width of 6,000 mm

Condition: used, Year of construction: 2018, An immaculate ex University research facility machine that is hardly been used. Photographed as it it arrived and not yet cleaned! 2018 built HAAS Mini Mill... Machine Control: Haas CNC Hfodpfx Apswzyd Eonji Table Size: 36" x 12" Machine Travels (X/Y/Z) : 16" x 12" x 10" (406 x 305 x 254 mm) Spindle To Table Distance : 4" - 14" (100 - 346mm) Table Capacity : 500 Lbs.(1200 Kgs) Spindle Speeds : 6,000 Max RPM Rapid Traverse Rate (X/Y/Z) : 600 IPM (15M/Min) Maximum Cutting Feed Rate : 500 IPM (13 M/Min) Tool Changer Style : Carousel Tool Changer Capacity : 10 Stations Tool Change Time : 4.2 Seconds Max Tool weight : 12 Lbs. Spindle Drive : 7.5 HP Equipped with: 40 Spindle Taper, 10 Station Automatic Tool Changer, Coolant system, Rigid Tapping, Tooling & Manuals Control: HAAS Spec: Travel X406 Y305 Z254 mm | 6000RPM | BT40 Accessories: 40 Spindle Taper, 10 Station Automatic Tool Changer, Coolant system, Rigid Tapping, Tooling & Manuals

Condition: excellent (used), Year of construction: 2018, Hartford LG-500 Vertical Machining Centre Hfodpfxowif R Ts Apnji Year: 2018 (only 400 working hours) Model: LG-500 Control: Hartford Plus 3 Table Size: 620 x 420mm Table Load: 300 kgs Axis Travels X/Y/Z: 620 / 420 / 450mm Spindle Nose to table: 100 – 550mm Spindle Taper: 40 INT Spindle Speeds: 12,000 RPM 12 station ATC Machine as new

Condition: excellent (used), Year of construction: 2010, operating hours: 32,300 h, functionality: fully functional, travel distance X-axis: 660 mm, travel distance Y-axis: 406 mm, travel distance Z-axis: 508 mm, rapid traverse X-axis: 24 m/min, rapid traverse Y-axis: 24 m/min, rapid traverse Z-axis: 24 m/min, nominal power (apparent): 11 kVA, controller manufacturer: Hurco, controller model: WINMAX, workpiece weight (max.): 340 kg, table width: 356 mm, table length: 762 mm, table load: 340 kg, overall weight: 2,900 kg, spindle speed (max.): 10,000 rpm, operating hours of spindle: 32,300 h, spindle motor power: 11,000 W, spindle nose: CAT 40, number of spindles: 1, number of slots in tool magazine: 20, input voltage: 400 V, type of input current: three-phase, Equipment: documentation/manual, rotational speed infinitely variable, 2010 Hurco VM10 CNC Milling Machine with CAT 40 Spindle, WINMAX Control 2010 Hurco VM10 Vertical Machining Centre with WINMAX CNC Control, CAT 40 spindle, 20-tool ATC and premium software package. Good condition. Delivery throughout Ireland, UK & Europe. Manufacturer: Hurco Model: VM10 Machine Type: 3 Axis Vertical Machining Centre Year: 2010 Hours: 32,300hrs Control: WINMAX Condition: Excellent For sale is a 2010 Hurco VM10 Vertical Machining Centre in good working condition, equipped with the renowned Hurco WINMAX CNC Control (Version V08.01.04.33) and a CAT 40 10,000rpm spindle. The Hurco VM10 is recognised worldwide as one of the most reliable and user-friendly vertical machining centres for precision CNC milling, toolroom machining, prototype manufacture, small batch production, mould making, and general engineering. With 32,300 machine hours, this machine remains an excellent opportunity for engineering companies looking for an affordable, high-quality used CNC machining centre from one of the industry's most respected manufacturers. Please note: No tooling is included with the machine. Technical Specifications Manufacturer: Hurco Model: VM10 Year: 2010 Machine Type: Vertical Machining Centre CNC Control: Hurco WINMAX Mill V08.01.04.33 Machine Hours: 32,300 Hours X Axis Travel: 660 mm Y Axis Travel: 406 mm Z Axis Travel: 508 mm Table Size: 762 × 356 mm Maximum Table Load: 340 kg Spindle Taper: CAT 40 Spindle Speed: 10,000 RPM Spindle Motor: 11 kW (15 HP Peak) Automatic Tool Changer: 20 Station ATC Rapid Traverse (X/Y/Z): 24 m/min Machine Weight Approx.: 2,900 kg Condition: Excellent Working Condition Tooling: No Tooling Included Installed WINMAX Software Options This machine is equipped with an excellent range of factory software options including: Advanced Verification Graphics DXF File Import NC Productivity Package Industry Standard NC Programming UltiPockets Rigid Tapping Hjdpfxoziu Hzj Apnefi Helical Ramp Milling 3D Mold Package NC Conversational Merge Swept Surface Machining Select Surface Finish Quality These options significantly enhance programming flexibility, machining accuracy and production efficiency, making the VM10 suitable for both conversational programming and full ISO/G-Code machining. Notes: *Specifications are given in good faith but not guaranteed* Key Features Hurco WINMAX Conversational CNC One of the easiest CNC controls to learn and operate, allowing operators to quickly produce components without extensive G-Code programming. CAT 40 High-Speed Spindle The industry-standard CAT 40 spindle provides excellent tooling availability and rigidity for machining steel, aluminium, plastics, composites and engineering materials. 20 Station Automatic Tool Changer Fast automatic tool changes reduce machining time and improve production efficiency. Compact High-Performance Design Large machining travels combined with a compact footprint make the VM10 ideal for workshops where floor space is at a premium. High-Speed Precision Machining The 10,000 RPM spindle combined with rapid traverse rates enables efficient production while maintaining excellent surface finishes. Proven Hurco Reliability Hurco machining centres are recognised worldwide for their durability, ease of maintenance and excellent resale value. Machine Condition: Excellent Condition Fully operational Ready for immediate production No tooling included in sale Inspection welcome

Condition: used, Year of construction: 1997, functionality: unexamined, Bridgeport VMC 600 vertical machining centre Hsdpfx Apjzmaf Ronefi Year (1997) with GE Fanuc Series O-M control, 22 ATC, Cromar swarf conveyor

Condition: used, YOM 2004 Mazatrol PC Fusion 640 M Axis X 1660 mm Axis Y 510 mm Axis Z 510 mm Table length 2000 mm Table width 510 mm Hfodpfxev Ax Uyo Apnsi Max. part weight 1000 kg Number of tool pockets 30 Spindle taper CAT 40 Max. spindle speed 10000 rpm Spindle motor power 18.5 kW

Condition: good (used), Year of construction: 2011, 2011 CMS Ares 48/18-New PX5 CNC 5-axis High-Speed Machining Centre Table Dimension 4,870 x 1,360mm. Axis Travel 'X'=4,800mm, 'Y'=1,800mm, 'Z'=1,200mm. 'B'=±120°, 'C'=±270°. Rapid Traverses 'X'=80m/min, 'Y'=80m/min, 'Z'=70m/min, 'B'=9,000°/min, 'C'=9,000°/min. Maximum Spindle Speed 24,000rpm. 8 Position ATC. Spindle Taper HSK 63. S/No. 5790. Hfedpfx Aszk I Tdopnoi

Condition: used, Year of construction: 2005, functionality: fully functional, travel distance X-axis: 730 mm, travel distance Y-axis: 850 mm, travel distance Z-axis: 560 mm, workpiece height (max.): 500 mm, workpiece diameter (max.): 730 mm, workpiece weight (max.): 500 kg, total length: 630 mm, table width: 500 mm, table load: 500 kg, Mazak Variaxis 730-5X Simultaneous 5 axis CNC Vertical Machining Centre Model: Variaxis 730-5X S/No.: 567181684 Year: 2005 Country of Origin: Japan Control: Mazatrol 640M 5X ‘X’ axis Travel: 730mm ‘Y’ axis Travel: 850mm ‘Z’ axis Travel: 560mm ‘A’ axis: -120 degrees tp+30 degrees ‘C’ axis: continuous 360 degrees Hodpjzhl Erofx Apnjfi Table Size: 630 x 500mm Max. Table Load: 500 kgs Max. workpiece dia.: 730mm approx. Spindle Taper: ISO 50 Spindle Speed: 10,000 RPM

Condition: good (used), Year of construction: 2017, Traverses X Y Z: 1067mm x 610mm x 610mm, Table size 1270mm x 610mm, 600mm C axis Table (360 degrees) +/- 90-degree head (B axis), 37kW Spindle Motor, Hedpfxezh Ncze Apnofi 40 station side arm ATC, din 40 spindle taper, 12,000rpm spindle, Hurco Winmax 5 control, through spindle coolant, swarf conveyor, spindle probe.

Condition: good (used), Year of construction: 2018, Traverses X Y Z: 1,525 x 660 x 610mm, Table 1675 x 660mm, table load 2,000 kgs, Spindle speed 12,000 rpm, input 18Kw, Hurco Winmax 5Control, Spindle taper Din 40, Hfedpfozh I Ebex Apnji 30 ATC, Coolant, Low volt light, Swarf Conveyor, spindle probe

Condition: good (used), Year of construction: 2019, Traverses X Y Z 762 x 508 x 520mm, A axis 30/110 degrees, C axis 360 degrees, table size 250mm diameter, table load 200kgs, spindle speed 12,000 rpm, spindle taper Din 40, Hfedpfezh I Agjx Apnei 40 station ATC, WinMax 5 control, through spindle coolant, swarf conveyor.

Condition: excellent (used), Year of construction: 2017, Traverses X Y Z: 1016mm x 508mm x 508mm, table size 1168mm x 508mm, 10000rpm spindle, Hjdpfezh Hw Nex Apnofi 20 station ATC, BT40 spindle taper, input 15kW, Hurco WINMAX 5 control, coolant, swarf auger.

Condition: excellent (used), Year of construction: 2019, Traverses X Y Z: 762 x 508 x 610mm, Table 1020 x 510mm, Spindle speed 15,000 rpm, input 15Kw, Hurco Winmax 5 Control, Spindle taper BT40, 30 ATC, Coolant, Low volt light, Swarf Conveyor. Hsdpfezh Hvxox Apnsfi

Condition: good (used), Year of construction: 2013, Traverses XYZ: 762 x 435 x 510mm, table size 920 x 435mm, ISO40 spindle taper, spindle speed 12000 rpm, FANUC i Control, spindle motor power 15kW, Hfsdpfx Aozhwg Uspnsi 30 station ATC with side arm, Through Spindle Coolant, Low Volt Light, Swarf conveyor

Condition: used, machine/vehicle number: J500111T, Hardinge Bridgeport Interact T450P Vertical Machining Centre Siemens 810D CNC Control Table Size: 500 × 400mm X-Axis Travel: 450mm Y-Axis Travel: 400mm Z-Axis Travel: 450mm Spindle Taper: BT40 Spindle Speed: 8,000 rpm Spindle Motor: 7.5/11 kW AC Spindle Motor ATC 20 Station Carousel Machine Weight: 2,500 kg Supplied with: 20 Station Automatic Tool Changer Electronic Handwheel (MPG) Coolant System Worklight Hodpfx Apjzkalfonsfi Fully Enclosed Guarding Automatic Lubrication Interlocked Safety Door Three Colour Machine Status Beacon For Sale with Jet Machinery Ltd Jet Machinery Stock No: 79208 Machine Serial Number: J500111T Cost: £11,950.00 + VAT Whilst every effort has been made to ensure that the above information is accurate it is not guaranteed. We advise prospective purchasers to check any vital details. Health and Safety At Work Act 1974: It is not reasonably practical for ourselves as suppliers to ensure that for your application the goods comply with requirements of the Act with respect to guarding etc. Prospective purchasers should ensure that a guarding specialist inspect the goods prior to use.

Condition: used, Year of construction: 2016, Mazak Vertical Centre Smart 530C CNC Vertical Machining Centre with Mazatrol Matrix 2 Control. S/No. 270242 (2016), Table Size 1300mm x 550mm, Spindle Speed Max 12,000rpm, 30 Tool Drum Type ATC Fitted with Various Tool Holders and Renishaw Probe, CAT40 Spindle Taper, LNS Turbo MH500 Swarf Conveyor, Machine Weight 6800kg, User Manual on CD. Country of Origin: United Kingdom Hsdozi Tatopfx Apnjfi Location: These lots are located in Gateshead, UK. Unfortunately there are no loading facilities on-site, dismantling and loading will be at the cost of the purchaser. All/Any tooling is being offered as specifically described.