Used Vertical Head for sale (15,616)

Condition: used, Vertical milling head, milling head, angle milling head MAHO suitable for MH300 or MH400. Year of manufacture approx. 1990. Tool holder: SK 40. Quill stroke: 60 mm. Centering diameter on the flange plate: 102 mm. Outer diameter of flange: 180 mm. Bolt circle on flange plate: Ø 150 mm. Mounting holes on flange plate: 4x Ø 11 mm. - Quill feed: 0.015 / 0.03 / 0.06 / 0.12 mm/rev. - Head drive via shaft Ø 32 with 10 mm keyway. - Knurled wheel with scale for quill stroke. - Angle scale on angle milling head 2x 90°. Dimensions L x W x H: 300 x 280 x 300 mm. Total weight: 31.4 kg. In good condition. Nodjxf Ur Nopfx Aqwslf

Condition: used, Keyway milling head, head for DECKEL milling machine, type FP 1 Factory number: 21948 Dovetail width: approx. 74 - 88 mm Dovetail height: approx. 14.5 mm Dovetail length: 285 mm Distance from the front edge of the dovetail to the center of the gear: approx. 200 mm Stroke size: max. 80 mm Stroke rate: max. 475 double strokes/min. Tool holder: 4-sided, 16 x 16 mm with clamping plate - Stroke size adjustable via eccentric adjustment - Drive from the machine gearbox, within the dovetail guide (as with the normal vertical head) - This keyway milling head is inserted into the dovetail guide in place of the normal vertical milling head (Mounting in place of the vertical milling head) - Drive gear in the keyway milling head, 39 teeth, gear width 15 mm, presumably 15° pressure angle Nsdpfx Aqoznn Hrjwolf - Keyway milling head can be rotated 360° on the flange plate, degree scale +/- 35° - Small breakout point on the housing Weight: 28.5 kg DECKEL FP1 has a pressure angle of 15° on the drive wheel. DECKEL FP2 + FP3 have a pressure angle of 20° on the drive wheel.

Condition: excellent (used), Vertical head MWM Ruhla SK 40 Pinion travel 80 mm Diameter of mounting flange 180 mm Bolt circle diameter 135 mm Four mounting holes, diameter 15 mm Diameter of centering pin 75 mm Nlodozdub Ispfx Aqwef Height 500 mm Width 190 mm Depth 250 mm Weight 50.5 kg

Condition: used, Vertical milling head, milling head with motor drive THIEL Tool holder: MK 5 (Morse taper size 5) Nsdpfxsxddwre Aqwjlf Quill stroke, spindle travel: 80 mm Spindle speed at motor speed 1410 rpm = 490 / 780 / 1200 rpm. Spindle speed at motor speed 2950 rpm = 970 / 1530 / 2380 rpm. Spindle bore: 37 mm Motor power: 1.4 / 1.8 kW Motor speed: 1410 / 2850 rpm Power connection: 400 Volt, 50 Hz - Spindle speed via 2 motor speeds and 3 belt stages - Mounting flange milling head Ø 215 mm with 2 bores Ø 15 mm, hole spacing 180 mm - suitable for tools with drawbar thread (ejector tang interferes with clamping) Required space L x W x H: 450 x 400 x 350 mm Net weight: 61 kg Good condition

Year of construction: 2016, condition: excellent (used), functionality: fully functional, We offer this Apollo SRL Macchine Utensili Modular 1 vertical head punching machine, type MB045161215, manufactured in 2016, in very good condition. Nledpfx Aszrpfksqwof If you have any questions or require further information, please contact us by email or phone.

Condition: used, Year of construction: 1984, Milling Head vertical accessory for a milling machine Fritz Heckert FSS 400 - weight 255 kg - dimensions: LxWxH: 560 x 500 x 400mm - swiveable 90° right / left - clamping area 500 x 400mm Nlodpfxou N E Abs Aqwof *

Condition: used, VERTICAL MILLING HEAD Accessory for a Fritz Heckert FSS 400 milling machine Weight: 285 kg Dimensions (LxWxH): 550 x 500 x 550 mm Swivels 90° to the right / left Clamping surface: 500 x 400 mm Taper: SK 45 Flange diameter: D = 260 mm Mounting: 4 holes, diameter D = 17.5 mm Nljdpov U I Sljfx Aqwjf *

Condition: used, Accessories for e.g. a bench drill BFT 130: The spindle head and swivel angle can be swivelled 360° around their own axes. Two swivel planes The set angles can be read off on circumferential scales Speed max. 600 rpm. Spindle taper ISO 50 Njdpju Nlgyefx Aqwslf Weight approx. 270kg incl. connecting piece to the drive SK 50 pinoler/head *

Condition: like new (used), 1 unused universal vertical milling head, suitable for an ORADEA / EURO-MILL FUS 32 Design: “MAHO”, ISO 40 shank, quill stroke 100 mm, designed drive power approx. 3-4 kW, max. speed 2000 rpm, … Optional accessories: - Multiplier, gear ratio 1:4, ISO 40 shank Price: EUR 499.00 - Attachment for automatic feed device for the vertical milling head quill, “MAHO” system, 6 feeds 0.02 - 0.2 mm/rev Price: EUR 1,880.00 - Cross milling head, additional head for the vertical milling head with spindle taper ISO 30, rotatable, 360 degrees Price: EUR 585.00 Nledjddtwbjpfx Aqwjf plus statutory VAT. Siegfried Volz Werkzeugmaschinen Rüschebrinkstr. 151-153 DE - 44143 Dortmund - Wambel / Germany

Condition: good (used), 1 used, well-maintained vertical milling head with large overhang, previously installed on a PAMA (Origin Italy) boring mill. Spindle taper: SK 50 Overhang: 660 mm Flange dimensions: 465 x 440 mm Internal bore: 294 mm Speed range: up to approx. 1,500 rpm Max. drive power: approx. 22 kW Dimensions (L x W x H): 750 x 440 x 465 mm Weight: 240 kg Accessories / Special features: • 1 rotatable axis (left/right) • Continuously adjustable angle, manual • 4 fixed indexing points at 90° each with locating pins Nodsyc Nhhjpfx Aqwolf • Tool clamping with drawbar • Suitable for retrofitting to conventional, NC or CNC milling machines or boring mills of any kind, swivels left/right, manual tool clamping, ... Siegfried Volz Werkzeugmaschinen Rüschebrinkstr. 151-153 DE - 44143 Dortmund - Wambel

Condition: used, Keyway milling head for milling machine, milling head, CCCP / USSR STANKO Type 1502 No.: 200 Year of manufacture: 1974 Stroke size: max. 60 mm Nlodpod Dk A Asfx Aqwjf Stroke rate: approx. 200 - 500 strokes/min. Tool holder: 12 x 17 mm with clamping plate Hole spacing machine flange plate: 245 x 185 mm Mounting hole: Ø 17 mm Centering diameter on the machine flange plate: 190 mm - Stroke size adjustable via eccentric adjustment - The drive is the same as for the standard vertical head, driven by the machine gearbox - Drive via a drive pin, centered within the centering diameter - Graduated scale on the flange plate, +/- 45° infinitely adjustable - This keyway milling head is flanged in place of the standard vertical milling head (Mounting in place of the vertical milling head) Weight: 42 kg Good condition Keyway milling head, bearing number 58166, and vertical milling head, bearing number 58164, from an identical STANKO milling machine.

Condition: excellent (used), Year of construction: 1989, Type: EDU / 80 DR EK ICH FQW / FQS Q ApW/Q ApSS Number: 1824/1989 Mounting: SK 50 Contact surface, W x H: 480 x 460 mm Hole spacing, W x H: 425 x 415 mm Gear diameter, internal / external: 75 / 100 mm Speed range: 18 to 2,800 rpm Condition: very good Nodjh Ar Tyspfx Aqwelf Weight: 280 kg Dimensions: 560 x 410 x 1,000 mm

Condition: ready for operation (used), Year of construction: 1979, VTL BERTHIEZ (France) TM 500 SP Model: TM500 8P Year of Manufacture: 1979 Chuck diameter: 6300 mm Max. turning diameter: 15000 mm Max. workpiece height: 4000 mm Arm travel: 3600 mm Main motor power: 100 kW Max. workpiece weight: 80 tons Side tool post section: 360x360 mm Nedpfx Aqox Dbydewjlf Side tool post travel: 2500 mm Machine weight: approx. 230 tons Video available Milling and hobbing heads available

Condition: used, Filling and weighing line: “Ishida” Multihead weigher Type CCW-EZ-214/30 Heads: 14 pieces max 50 programs (0-49) Performance: up to max 99 weighings/min Accuracy: average 0 to + 1.0 g Weighing volume: 50-3000 g Display: micro controller display Ambient temperature: 0°C - 40°C Humidity: 35-85% (no condensation) Smallest setting: 0.1g + Vertical flowpackaging line “Rovema” Type VPK260 - 14961 yoc 2005 Performance (mech.) Cycles/min: 180 Roll width / diameter (max.) (mm): 450/ 550 (600 / 550 with pre-unrolling) Bag width (min. - max.) (mm): 60-260 Bag length (min. - max.) (mm): 120-600 Fill volume (max.) (cm³): 6000 Sealing pressure (max.) (N): 5000 (optional: 8000) Program memory: Standard: 100 (optional: 1000) Dimensions: (L x W x H) (mm): 2.200 x 1.430 x 1.620 mm Nljdozwdfcopfx Aqwef Weight: 920 kg Power supply (volts): 230 / 400 Energy requirement (kVA): 8 Protection class: IP54 Compressed air connection: 6 bar Air consumption 6 bar (NI/cycle): 0.25 Machine color: Ral 9007L / gray aluminum Operating temperature (min. – max.) (°C): +5 … + 45 Storage temperature (min. – max.) (°C): -20 … +50 Air humidity (max.) (%): 15…95; no condensation in good condition

Condition: good (used), Year of construction: 2004, functionality: fully functional, We are offering this well-maintained Multi Weigh, Delta Pack MKW: HDW10 3.5 pouch filling machine: DE420 FU multi-head weigher with pouch filling machine, manufactured in 2004. Nedpjzlnbwjfx Aqwelf Manufacturer: Multi Weigh, Delta Pack Model: MKW: HDW10 3.5 pouch filling machine: DE420 FU Year of manufacture: 2004 Condition: good Category ID: 703 Type: Multi-head weigher with pouch filling machine If you have any questions or require further information, please do not hesitate to send us a message or call us.

Condition: new, Year of construction: 2024, New Grundfos Pump - Vertical, multistage centrifugal pump with integrated frequency converter. inlet and outlet ports on same the level (inline). The pump head and base are in cast iron – all other wetted parts are in stainless steel. A cartridge shaft seal ensures high reliability, safe handling, and easy access and service. Power transmission is via a rigid split coupling. Pipe connection is via DIN flanges. The pump is fitted with a 3-phase, fan-cooled asynchronous motor. The motor includes a frequency converter and PI controller in the motor terminal box. This enables continuously variable control of the motor speed, which again enables adaptation of the performance to a given requirement. An operating panel on the motor terminal box enables setting of required setpoint as well as setting of pump to "Min." or "Max." operation or to "Stop". The operating panel has indicator lights for "Operation" and "Fault". Communication with the pump is possible by means of Grundfos GO Remote (accessory). The remote control enables further settings as well as reading out of a number of parameters such as "Actual value", "Speed", "Power input" and total "Power consumption". The terminal box holds terminals for these connections: • pump start/stop input (potential-free contact) • remote setpoint setting via analog signal, 0-10 V, 0(4)-20 mA • 10 V voltage supply for setpoint potentiometer, Imax = 5 mA • three analog sensor inputs, 0-10 V, 0(4)-20 mA • 24 V voltage supply for sensor, Imax = 40 mA • one analog output • three digital inputs • two Pt100 inputs • two potential-free fault signal relays with changeover contact, reporting "Fault", "Operation" or "Ready" Nlodpfxoyug R Rj Aqwef • RS-485 GENIbus connection • interface for Grundfos CIM fieldbus module

Condition: new, Year of construction: 2024, NEW Grundfos - The pump is fitted with a 3-phase, fan-cooled, permanent-magnet, synchronous motor. The motor efficiency is classified as IE5 in accordance with IEC 60034-30-2. The motor includes a frequency converter and PI controller in the motor terminal box. This enables continuously variable control of the motor speed, which again enables adaptation of the performance to a given requirement. An operating panel on the motor terminal box enables setting of required setpoint as well as setting of pump to "Min." or "Max." operation or to "Stop". The Grundfos Eye indicator on the operating panel provides visual indication of pump status: "Power on": Motor is running (rotating green indicator lights) or not running (permanently green indicator lights) "Warning": Motor is still running (rotating yellow indicator lights) or has stopped (permanently yellow indicator lights) "Alarm": Motor has stopped (flashing red indicator lights). Communication with the pump is possible by means of Grundfos GO Remote (accessory). The remote control enables further settings as well as reading out of a number of parameters such as "Actual value", "Speed", "Power input" and total "Power consumption". The terminal box has a number of inputs and outputs enabling the motor to be used in advanced applications where many inputs and outputs are required: • two dedicated digital inputs • three analog inputs, 0(4)-20 mA, 0-5 V, 0-10 V, 0.5 – 3.5 V • 5 V voltage supply to potentiometer and sensor Nljdpfxoyug Hxs Aqwjf • one analog output, 0-10 V, 0(4)-20 mA • two configurable digital inputs or open-collector outputs • two Pt100/Pt1000 inputs • LiqTec, dry-running protection sensor input • Grundfos Digital Sensor input and output • 24 V voltage supply for sensors • two signal-relay outputs (potential-free contacts) • GENIbus connection • interface for Grundfos CIM fieldbus module.

Condition: good (used), Hohner Exact Plus 2-Head Stitcher Machine in perfect condition, ready for production. Semi-automatic booklet stitching machine equipped with two Universal 43/6 S stitching heads and a station for manual loading and automatic unloading of booklets onto the conveyor belt. Nlodpfjzurzyox Aqwjf Head spacing adjustment. Maximum booklet size: 420 x 360 mm Min. booklet size: 100 x 80 mm Maximum throughput: 4000 cycles/hour 380V power supply Safety guards. Machine complies with CE standards

Condition: good (used), Vertical steel tank 60,000l diameter 2.82 m total height 11 m a hatch at the top of the upper floor and at the bottom on the side of the cylinder. Each tank can be painted with epoxy resin coat, or sold sandblasted (no coat). 12 units available Nedjtwwv Nspfx Aqwjlf

Condition: excellent (used), Horizontal/vertical rotary table Chuck: Ø 350 mm Shelf diameter: Ø 400 mm Height without mandrel: 140 mm Total height: 250 mm Base dimensions: Length 430 mm x Depth 370 mm Weight: approx 150 kg Possibility to work horizontally or vertically The increment is done by the front handle Nljdpfx Aqszmw Upowsf

Condition: as good as new (ex-display), Year of construction: 2005, ACCEPTANCE OF SELF feed head is held on the guides of hardened cylindrical surface and additionally treated grinding. Three-phase motor power 3HP 2800 rpm / min. Output frontal saw blades with cutting heads. Feed discs cost of delivery SEMI AUTOMATIC DOUBLE MITRE SAW Technical Data Right head displacement by means hand wheel Reading of the cutting dimension on high precision metric scale with micrometric adjustment Sliding of the moving head by means of ricirculating ball bearings on rectified and tempered guides Radial sliding of the sawing group Full protection of the sawblades by means of safety hoods with automatic closing Pneumatic heads tilting at 90°/+ 45°/-45° Possibilty to mount sawblades Ø 500 - 530 - 550 mm 2,2 Kw (3 HP) 3 phase motors - 2800 r.p.m. Sawblade shaft Ø 30 mm Cutting lenghts 4000/5000/6000 mm Working pressure 7 bar Overall dimensions 524-624-724x139x155 cm Weight 1200 - 1350 - 1500 Kg Standard Equipment Horizontal pneumatic clamps Automatic lubrication by means of nebulizer Air filter Air gun Service spanners Optionals Reading of the cutting dimension on digital display Turning vertical clamps kit Pneumatic central support Manual central support Right head in feed roller conveyor Semi-automatic reduced cut modification c/w in feed roller conveyor Vee notch device for PVC profiles Micro-spray nebulising device Pneumatic support for long bars cover customer Startup type Njdpfob Rnv Ssx Aqwslf negotiated Description Notes Saw 2 a head for precision cutting of aluminum profiles GAMMA. Precise double miter saw for serial production of blanks at an angle of 90 ° and 45 °. Convenient and safe execution of multiple cutting operations. Automatic positioning of the moving cutting head. Automatic positioning of the moving cutting head. Adjustable stroke discs. The angles of inclination of the cutting head 45 °, 90 °, easy pneumatically. Intermediate angles are adjusted manually using the bumper and angular scale. LENGTH OF CUT = 4000 5220 x 1390 x 1460 mm Weight 1200 kg.

Condition: used, This listing is for the Watson Marlow 313DW Peristaltic Pump Head The unit is in full working condition and is ready for immediate release Key Features Nedpsxv Apwjfx Aqwjlf The Watson-Marlow 313DW is a single-channel, rapid-load peristaltic pump head designed for laboratory and industrial fluid handling applications. It is part of the 300 Series, known for their flip-top design that facilitates quick and easy tubing changes. Key Features High Flow Rate: The 313DW model is equipped with a three-roller mechanism, enabling a maximum flow rate of up to 2,000 mL/min when using 1.6 mm wall thickness tubing. Tubing Compatibility: Accepts standard 1.6 mm wall thickness tubing with bore sizes ranging from 0.5 mm to 8 mm, offering flexibility for various applications. Durable Construction: The pump head is built with a glass-filled polypropylene back; IXEF front; glass-filled nylon rotor, clamps, and mounting plate; and MoS₂-filled nylon rollers. These materials ensure strength, chemical resistance, and long service life. Roller Options: Choose the three-roller model for high-flow applications or the four-roller model for smoother flow and reduced pulsation. Extension Capability: Add up to five extension pump heads, depending on the type and size of tubing used. Note: The number of extension pump heads allowed depends on the type and size of tubing being used. Warranty: Includes a 1-year manufacturer warranty for quality assurance. Applications Chemical Processing: Ideal for accurate, contamination-free chemical transfer. Biotechnology: Suitable for sterile fluid handling. Food and Beverage: For transferring additives, colorants, and ingredients. Water Treatment: Used in dosing and chemical feed systems

Condition: used, functionality: unexamined, total height: 5,000 mm, total width: 1,200 mm, total length: 3,600 mm, input voltage: 400 V, input frequency: 50 Hz, DenoLift Vertical Carousel / Paternoster approx. 5 m – Fully Functional – Industrial We have a used DenoLift carousel (paternoster) that we are considering selling and would like to know if this system might be of interest to you. Nlodpfoyplqrjx Aqwef Specifications (indicative): Brand: DenoLift (Denocard) Type: vertical carousel / paternoster Dimensions: approx. 3.6 meters long × 1.2 meters wide Height: approx. 4 – 5.5 meters Control: numeric keypad with LED display (older model) Price: 5000 EUR This is an industrial storage system with significant capacity. The installation is currently set up and can be dismantled and collected by arrangement. Upon request, we can provide additional photos, a video of the system in operation, and any available technical data.

Condition: good (used), Hang 150 Double-Head Riveter for Binders Manufacturer: Hang Germany Njdpfxozhkive Aqwslf Machine has been overhauled and is ready to use. The machine is used for riveting all types of ring mechanisms. Two riveting heads with adjustable spacing. Cardboard thickness: 0.2-4mm Throat depth: 310mm Head spacing: adjustable from 35-440mm Cycle time: 0.5s Weight: 570kg Power supply: 380V The cycle is initiated by a foot pedal.

Condition: used, Drilling capacity: 35/40 mm Spindle mounting: MK 4 Overhang: 230 mm Nlodpfxjb N Ahls Aqwef Table size: 1050 x 625 mm Table height above floor: 560 mm Small/large distance between table and drill chuck: 549/960 mm Chuck travel: 170 mm Spindle speeds, continuously variable: 50 - 800 rpm Space requirement: 1050 x 1000 x 2170 mm Weight: 250 kg