Condition: good (used), Year of construction: 2007, power: 5.5 kW (7.48 HP), input voltage: 220 V, Husmann static press incl. funnel and container Merk: Husmann Type: ST-SEL-TS-V Hpodowcdq Sepfx Ad Eoa Build in: 2007 Weight: 5150 kg Engine: 5,5 kw Volume container: 32m3 Door for unloading: side hingend

Condition: reconditioned (used), Year of construction: 2015, operating hours: 28,748 h, functionality: fully functional, pressing force: 60 t, filling opening width: 1,100 mm, filling opening length: 1,500 mm, bale width: 1,100 mm, bale height: 750 mm, bale weight: 570 kg, overall weight: 20,000 kg, oil tank capacity: 600 l, power: 37 kW (50.31 HP), volume flow: 350 m³/h, Technical data baler: Manufacturer Presona AB, Sweden Type LP 60 VH1 Year of construction 2015 Total operating hours, 30,143 hours, as of July 2025 Effective pump running time onl 6,527 hours, as of July 2025 Number of pressed bales 115,193 bales, as of July 2025 Press force pre press 25 t Main press force 60 tonnes Specific pressing force 73N/cm² Dimensions of feed chute 1,500 x 1,100 mm Filling volume / pressing cycle 2.7 m³ Theoretical throughput capacity 800 m³/hour Throughput capacity under operating conditions 350 m³/hour Bale dimensions 1,100 x 750 mm Drive power 37 kW Tying 5-fold vertical, fully automatic Throughput capacity with a Bulk weight of 50 kg/cbm 11 to 14 tonnes/hour Bale weights 420 to 570 kg, depending on material Hydraulic oil tank volume 600 litres Baler dimensions assembled with hopper 10,100 x 3,750 x 4,310 mm (l x w x h) Transport dimensions excluding press 10,100 x 2,400 x 3,000 mm (l x w x h) Machine weight press approx. 20 tonnes Condition of the press: The press was partially overhauled in our workshop and then tested in manual and automatic mode. The following overhaul work was carried out: Machine cleaned, partially derusted and partially repainted Hydraulic oil tank emptied and cleaned Oil filter and air filter replaced, new hydraulic oil filled Press ram dismantled and cleaned All four rollers removed from the press ram and replaced Grease cartridges of the automatic roller lubrication system replaced Slide rails cut out from the press floor in the press room Underbody reinforced with welded sheets New HARDOX slide rails welded in Wire station with deflection rollers for the lower wire cleaned and made operational Slide rails cut out from the floor in the press channel New HARDOX slide rails welded in Both side walls of the press channel dismantled, derusted Hodpfx Adjvn Tg Ij Eepa Worn side wall plates cut out Complete side walls covered with new wear plates and welded Main hydraulic cylinder dismantled and disassembled for inspection Piston rod replaced, cylinder tube honed Complete seal set replaced, pressure test carried out Vertical needle system for binding dismantled, cleaned, wire deflection rollers made functional and serviced Chain cleaned, greased, chain tension readjusted Drillomat cleaned, wire knife, drill shafts and drill fingers checked, retightened with torque and serviced Machine checked, general maintenance work carried out and press tested in manual and automatic mode Comments: The press is sold without a conveyor belt and without wire stations. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors.

Condition: good (used), Year of construction: 1981, functionality: fully functional, Equipment: documentation/manual, Automatic channel baler BOA Continu 25 LB + conveyor belt. The baler is in good condition and has been regularly serviced. Recently, the Denison pump underwent a complete overhaul. Fully functional and in continuous operation. Please contact us for further information. Hpedpsw S Tv Usfx Ad Eja

Condition: excellent (used), Year of construction: 2002, functionality: fully functional, pressing force: 15 t, bale width: 700 mm, bale height: 700 mm, bale weight: 220 kg, input voltage: 400 V, power: 4 kW (5.44 HP), empty load weight: 2,700 kg, Manufacturer: Borg Baling Company Type: S-15KK Year of production: 2002 3x400V, 4kW, 14.5A Compression force: 15t Net weight: 2.7 t Bale max. sizes Hpjdpfx Adsh Dy Rfj Esa 700x700x1000 mm weight of a bale: ca 120 – 220kg Wide Range of Used Machinery, Industrial Equipment

Condition: reconditioned (used), functionality: fully functional, machine/vehicle number: Pal 1600, power: 180 kW (244.73 HP), input voltage: 380 V, warranty duration: 12 months, Equipment: documentation/manual, 1 pellet press brand: Paladin 1600-210 inner diameter die 850 mm tread die 210 mm Press is equipped with 2 motors each 90 KW n=1500. Press door is made of stainless steel with overload valve in door. 3 Roll press with 3 rolls on the press overhauled in a drilled or racked version Press is complete with mold lifting device and tools The press is completely overhauled and equipped with new bearings and wear parts such as front and rear sliders die washer etc. Also new V-belts and toothed belt. Also, all safeties will be observed and appropriate switches on Friction safety , door switch and inspection hatches will be fitted. Hpodpfxsq U R N Te Ad Eoa Refurbished pump unit for friction and V-belt tensioning Remark: Conditioner on the press is optional

Condition: reconditioned (used), Year of construction: 2013, Presto HAN10 Usable volume: 10cbm Filling opening: 1300x1500mm Hpedpfx Aod Hy Enjd Eja Machines are repaired, serviced, tested and sold painted in standard RAL. NEW: Polyamide, hydraulic hoses, oil & filters Images are reference images of machines we manufacture. We would be happy to make you an offer including delivery.

Condition: used, Year of construction: 2015, operating hours: 1,661 h, Manufacturer: Husmann Typ: SPB 20 SEL-E Volume: 20m3 Build in: 2015 Hedpowca Aqsfx Ad Eopa Backdoor: bovenscharnierend

Condition: reconditioned (used), Year of construction: 2005, operating hours: 30,408 h, functionality: fully functional, pressing force: 50 t, filling opening width: 1,100 mm, filling opening length: 1,250 mm, bale width: 1,100 mm, bale height: 720 mm, bale weight: 550 kg, overall weight: 16,000 kg, oil tank capacity: 600 l, year of last overhaul: 2024, Technical data baler: Manufacturer Presona AB Type LP 50 EH1 Year of construction 2005 Operating hours 30,408 hours, as of April Number of pressed bales 198,059 as of April Pressing force main press 50 tonnes Specific pressing force 63 N/cm² Theoretical throughput capacity 530 m³/hour Throughput capacity under operating conditions 260 m³/hour Dimensions of feed chute 1,250 x 1,100 mm Bale chamber volume 2.2 m³ Bale dimensions 1,100 x 720 mm, variable length Drive power 22 kW Tying 5-fold vertical, fully automatic Throughput rates with a bulk density of 30 kg/cbm 6 up to 7 tonnes/hour Bulk weight of 50 kg/cbm 7 up to 9 tonnes/hour Bulk weight of 100 kg/cbm 11 up to 14 tonnes/hour Bale density (paper/newspapers) 400 to 550 kg/m³ Hydraulic oil tank capacity 600 litres PLC control Telemecanique TSX Micro Schneider Magelis control panel Effective transport dimensions excl. baler 8,125 x 2,300 x 3,000 mm (L x W x H) Transport weight press approx. 16 tonnes Condition of the baler: The machine was partial overhauled in our workshop and general maintenance work was carried out. After completion of the overhaul work, the press was tested during operation and is available for sale at short notice. The following overhaul work was carried out: General work: Machine cleaned, derusted, primed, partially painted Wire entry marks in the press channel feed-throughs welded shut and smoothed Hydraulic unit: Hydraulic oil tank emptied, tank cleaned, new oil filled Oil filter and air filter replaced Leaky oil sight glass on hydraulic oil tank replaced All hydraulic hoses replaced Hjdpfx Adsu Thhrj Espa Electrics: English language installed in the programme menu Two key switches in the control panel replaced Control cabinet replaced Signal lamp on the control cabinet replaced Flaps end switch replaced Electrical system of the turbulator replaced, connected and tested Press ram: All four rollers removed from the press ram and replaced Main hydraulic cylinder dismantled, disassembled and partially overhauled, cylinder tube honed, complete seal set replaced, leak test performed All plastic wear pads on the press ram replaced Pre-press: Both bearings on the pre-press shaft replaced. Both hydraulic cylinders dismantled, disassembled and partially overhauled, both cylinder tubes honed, complete seal sets replaced, leak test performed. Scraper flap on the pre-press replaced. Binding system: Two complete needles with wire deflection rollers replaced Needles adjusted and set All wire deflection rollers in the needle heads replaced Drill fingers replaced Two drill shafts replaced All 8 wear plates on the Drillomat, under the drill fingers, replaced Scope of delivery: Only the baler will be sold. The documentation (Manual, CE-declaration, electr./hydr.-drawings), are completely available. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors.

Condition: new, Year of construction: 2021, power: 11 kW (14.96 HP), Equipment manufactured in 2021, installed but never commissioned/unused/as-new condition! SCREW PRESS STATION WITH 2 PC6500 BOXES FOR SALE! Technical specifications: Total length: 2480 mm Total width: 1660 mm Total weight: 2300 kg Loading height: 1350 mm Inlet dimensions: 1375 x 1490 mm Screw diameter: 750/500 mm Screw speed: 17 rpm Drive power: 11 kW Year of manufacture: 2021, never used! Hpjdjxxlpfjpfx Ad Eja Press station features screw conveying system + KEV (carton feed/diverter, coarse shredding device, equivalent to KZK but more powerful) PRICE ON REQUEST!

Condition: excellent (used), Year of construction: 1996, pressing force: 30 t, input voltage: 380 V, bale weight: 600 kg, type of input current: AC, overall weight: 3,000 kg, Manufacture: Philadelphia Tramrail Model: HT30036 Vintage: 1996 400V/45A, 3 phases, 15kW 180 bar system pressure 206 bar maximum system pressure Made of heavy-duty structural steel Average cycle time of 53 seconds Dimensions: 1980 x 1050 x 3860mm Advance height: 1400mm Hpodpfx Asm Amk Nsd Eoa Baling chamber: 1600 x 760

Condition: reconditioned (used), Year of construction: 1999, functionality: fully functional, type of input current: three-phase, power: 160 kW (217.54 HP), input voltage: 380 V, warranty duration: 12 months, year of last overhaul: 2023, Equipment: documentation/manual, 1 pellet press make: Buhler DPAB inner diameter die 660 mm tread die 138 mm Press is equipped with 1 motor 160 KW . Press door is made of Stainless steel with overload valve in door. 2 Roll press with 2 rolls on the press overhauled in dimple or racked version Press is complete with die lifting device and tools The press is completely overhauled and equipped with new bearings and wear parts such as front and rear sliders die washer etc. Also new V-belts Also, all safety devices will be observed and appropriate switches on Friction protection , door switch and inspection hatches will be fitted. Hpsdpfjrah Evjx Ad Eea

Condition: reconditioned (used), Year of construction: 2019, Presto HAN10R Press container for skip loaders 10 m³ usable capacity Discharge door hinged at the top Two-piece lid above filling opening, opening left/right Prepared for ramp operation Machines are overhauled, serviced, inspected, and repainted in standard RAL color before sale. Pictures are reference images of machines of the same type we have manufactured. We will be happy to provide a quote including delivery. Hpedow Uqngopfx Ad Esa

Condition: ready for operation (used), Year of construction: 2000, operating hours: 25,000 h, functionality: fully functional, pressing force: 50 t, overall weight: 17,000 kg, empty load weight: 17,000 kg, Technical data: Avermann Maschinenfabrik GmbH & Co. KG Type: AVOS 1410 BS-22/50 Year of manufacture: 2000 Pump operating hours: 25,000 hours Feeding channel dimensions: 1,400 x 1,000 mm Bale size: 1100 x 750 mm (width x height), length adjustable Hpedpfxow N Hlqj Ad Eea Drive power: 22 kW Net weight: 17 t Capacity: 5.5 tons/hour Bale weight: depending on the material, up to 500 kg Vertical, 4-fold tying, fully automatic PLC control: Siemens S7-1500 Assembled baler dimensions: 8,610 x 2,400 x 3,835 mm (length x width x height) Special equipment: Wear-resistant floor made of HARDOX steel The conveyor belt is not included with the machine. Documentation: the complete operating manual is available. Viewing is possible by prior appointment. We do not assume responsibility for the technical data or possible errors. Condition of the press: It is in working condition thanks to continuous servicing. It has been used exclusively for baling paper. Avermann baler type AVOS 1410 BS-22/50, including wire-drawing stations and bale chute.

Condition: excellent (used), Year of construction: 2017, pressing force: 20 t, Technically well-functioning, fully equipped Bramidan B20 baler Hpodpfxoxwqn Do Ad Eja

Condition: used, Revolving briquetting press RUF type RBK 55/2500/120 S Hydraulic pellet press or briquetting press for grinding sludge, metal chips, or similar No. 70002 Year of construction 2009 Briquette diameter 120 mm Briquette length in the pre-compactor approx. 120 mm Pressing force in the pre-compactor 30 tons at 260 bar Briquette length in the main compactor approx. 80 mm Pressing force of the main press cylinder 250 tons at 260 bar Stroke size of the main press cylinder 120 mm Pressing force of the counter-press cylinder 250 tons at 260 bar Stroke size of the counterpress cylinder 15 mm Piston diameter of the main press cylinder 350 mm Press stroke Cycle time approx. 30 sec. for grinding sludge with low residual oil content Hopper size of the screw conveyor 1000 x 600 mm Hydraulic motor power 37 kW Mains connection 400 Volt, 50 Hz, 45 kW - Revolver with 5 stations for high material throughput - Pre-compressor stage for pressing material into the turret disk - 2 opposing main press cylinders with 120 mm and 15 mm stroke - Ejection cylinder for ejecting the finished briquettes from the turret disk - Infinitely variable adjustment of the hydraulic speed for each pressing stage - was used for grinding sludge from metal processing Hedpfx Ashg Uz Iod Espa - Material hopper as hopper with screw conveyor - the machine was completely overhauled at RUF in 2018 - a new SIEMENS Simatic touch panel was installed in 2020 - only a few operating hours after the overhaul very good condition Grinding sludge recycling - great savings through cooling lubricant recovery - Large savings in disposal costs due to the reduction in volume and weight of the grinding sludge - Grinding sludge briquettes with a low residual oil content can possibly be classified as "non-hazardous waste".

Condition: good (used), Year of construction: 1985, functionality: fully functional, pressing force: 50 t, bale length: 1,000 mm, bale width: 750 mm, bale height: 750,750,750 mm, bale weight: 500 kg, input voltage: 400 V, overall weight: 7,500 kg, oil tank capacity: 500 l, power: 30 kW (40.79 HP), empty load weight: 7,500 kg, input frequency: 50 Hz, Manufacturer: Paal Typ: Pacomat V Year of construction: 1985 Press power main press: 50 t Specific press capacity: 5 kg/cm² Feed channel: 1.000 x 720mm (l x w) Theoretic throughput rate: 200 cbm/h Bale size: 700 x 1.000 mm (w x h) length adjustable Driving motor: 30 kW Hsdpeic Rl Dofx Ad Espa Bale weight: approx. 500 kg Machine weight: approx. 8t The hydraulic unit is functional, the drive motor is in the removed state.

Condition: ready for operation (used), DIXI 60SLD is a semi-automatic baling system with a pressing force of 60 tons, designed for economical volume reduction of recyclable residues in industrial and craft sectors: - Cardboard boxes - Foams - PET bottles - Insulation mats - and other pressable materials Horizontal baler, DIXI 60 SLD waste press with tipping device Technical specifications: Pressing force: 60 tons Specific pressure: 6.81 kg/cm² Power supply: 400V / 7.5kW Bale dimensions: 800 x 1100 x 1200 mm Number of ties: 3 Bale weight: approx. 370–410 kg Tying: manual Feed opening: 990 x 1110 mm Machine weight: 5,420 kg Average pressing cycle: 47 sec Year of manufacture: 2011–2016 Dixi 80SLD Baler Technical Data of the Baler Hedora A E Uepfx Ad Eopa Brand: Dixi Model: 80 SLD Pressing force: 80 tons Drive power: 11 kW, 400 V / 32 A Feed opening (W x H): 1040 x 1110 mm Pressing cycle: approx. 35 sec Throughput: approx. 1,000 kg/h Bale size (W x H x L): 1120 x 1120 x 1200 mm Bale weight: depending on material, approx. 500–600 kg Bale tying: triple, manual Machine dimensions: Length: 4,200 mm (+cage 1,600 mm) Width: 1,830 mm Height: 2,620 mm Machine weight: approx. 8,000 kg Automatic bale ejection Robust construction for long-term use Year of manufacture: 2016–2020 Weight: approx. 8.4 tons Condition: Used

Condition: used, Year of construction: 2014, pressing force: 122 t, overall weight: 40,000 kg, pressure: 315 bar, Machine has been used but is surplus and therefore for sale! Hpjdpswa N U Defx Ad Eoa

Condition: new, For the industrial production of rectangular briquettes The ZBP 500 briquettes pressable materials into highly compressed briquettes. The briquettes are easy to store and can be easily transported thanks to their stackability. The briquettes are formed in the press chamber of the hydraulic press unit using a pressure cylinder. This means that up to nine briquettes can be produced per minute with a pressing force of 1 kg/cm². Standard equipment: Hpodpfjghgcqex Ad Esa Safety limit switch for oil temperature and level Oil cooler Automatic briquette length monitoring Automatic fill level monitoring for hoppers Control cabinet with PLC control for fully automatic operation Options: Hopper attachment can be supplied individually according to customer requirements Press stamp with lettering/logo

Condition: excellent (used), Year of construction: 2018, functionality: fully functional, pressing force: 50 t, Fully functional Bramidan B50 baler, serviced, complete set - hook, strap rolls. Hpedpjxg Tk Tefx Ad Eja

Condition: new, The briquette press is designed for pressing all kinds of sawdust and wood chips into briquettes. The design of the briquetting press is compact, handy and produced in Germany. The large oil tank allows continuous use. The briquette press is ready for immediate use - so plug in and go. Hpedpfjkyza Dex Ad Esa

Condition: excellent (used), Year of construction: 2015, operating hours: 97 h, functionality: fully functional, pressing force: 10 t, Fully serviced, fully equipped and ready to use. New oil. 5 units in stock. Hpedpfx Ajw Ey Dtjd Eea

Condition: new, machine/vehicle number: AMIS Brikettierpressen Typ ZBP 50, 60 und 70, AT A GLANCE: Variable container dimensions (on customer request) Left- or right-hand design Hydraulics with separate oil tank All series can also be equipped as "DUO" variants Wood chips, sawdust, sawdust etc. accumulate in all craft and industrial enterprises of the wood processing industry. Enormous storage and transport costs are claimed for this on a daily basis. Briquetting presses offer an ideal solution to this problem, as briquettes, on the other hand, are easy and space-saving to store and transport. In addition, spontaneous combustion is much less. Hodpoghgciofx Ad Eopa The briquetting presses require little space, are robustly built and equipped with low-maintenance technology. Whether wood, paper, biomass, foam or polystyrene - the ZBP briquettes any suitable material. With a throughput capacity of up to 35 - 130 kg/h, they are particularly suitable for small and medium-sized companies. Versatile set-up options due to availability as left-hand and right-hand versions. So start briquetting!

Condition: excellent (used), Year of construction: 2012, Tested, cleanded, full service was made. New oil. Hpodpfx Adorxfn Ue Eja We have two Orwak 5030 balers. Last photo - green, refurbished 2017 - 2000 Eur.

Condition: like new (used), Year of construction: 2024, functionality: fully functional, pressing force: 30 t, Used Bramidan B30 baler. Newly repainted. Ready for use, fully equipped, in perfect working condition. New oil. Hpjdpfsviymwox Ad Eoa