Used Mvf 44 for sale (3,495)

Condition: good (used), Gear motor, electric motor, three-phase motor, electric gear motor -Gearbox manufacturer Bonfiglioli type: MVF44/F -Manufacturer engine AEG type: AD63NZ4 -Speeds: rpm -Power: 0.18 kW -Construction: B5 angle -Diameter shaft: Ø 22 mm -Protection class: IP 44 -Number: 4x engines available Tedpfx Aeci Evtjkied -Price: per piece -Dimensions: -Weight: 7.2 kg/piece

Condition: used, Year of construction: 1975, functionality: fully functional, overall weight: 10,000 kg, total length: 2,745 mm, total width: 2,360 mm, total height: 2,700 mm, type of cooling: air, BBC BROWN BOVERI (nowadays ABB) – Pouromat, pouring furnace, type XCQ 44 TECHNICAL DATA - crucible capacity: 4.4t - tilting furnace - inductor 120kW - inductor voltage 380/425V - 2 operating modes: preheating, heating mode 1 - pouring rate: 1-20kg/s - dimensions:  height: approx. 2700mm  length: 2745mm Todezfyu Ajpfx Akied  width: 2360mm - weight: approx. 10,000kg - furnace equipped with a bottom-pour stopper - average inductor lifespan: 12 weeks - average bottom-pour stopper lifespan: 1 week - average crucible lifespan: 4 – 6 months - furnace equipped with an additional device used to modify the liquid metal with ferrosilicon CONSTRUCTION The pouring furnace consists of four basic groups: - First group – longitudinal travel (orbit motor) - Second group – transverse travel, including the bottom-pour stopper - Third group – inductor with a power of 120 kW, voltage 380 V 50Hz, whose main task is to heat the liquid metal. The inductor is constantly air-cooled during operation. - Fourth group – switchboard with a built-in transformer, contactors and control station. POURING PROCESS The pouring process proceeds as follows: DISAMATIC 2032 A displays the molds on the conveyor in the correct position. The correct position means that the open pouring basin in the mold is located in a position compatible with the bottom-pour stopper at the bottom of the crucible. If the desired position is achieved, the operator manually (by means of a lever) lifts the bottom-pour stopper in order to fill the mold, until the liquid metal is visible in the outflow. The speed of pouring the molds can be adjusted depending on the diameter of the ceramic block and the orientation of the bottom-pour stopper towards the ceramic block. CERAMICS The manufacturer, BBC, recommends using a two-layer firebrick lining, where one layer is permanent, but the second is expendable. The permanent lining consists of an insulating layer, which is a lightweight burned stone, and a sillimanite layer. The expendable layer consists of a corundum material, meaning a concrete with a high clay content (94%). Both parts are connected together by means of a special cement. The crucible inductor is located in a lining of Al₂O₃ or MgO and SiO₂, depending on the requirements. The material used to seal the bottom-pour stopper has the quality of chamotte with different clay content. The inductor is assembled to the pouring furnace by means of screws and a sealing compound with the proper plasticity and heat resistance. The entire device consists of three stopper rod sleeves, a bot, and a ceramic block, where the bot and stopper rod sleeves are connected together. The bottom-pour stopper is seated on a threaded bar. The bottom-pour stopper is continuously air-cooled. Recommended air pressure: 6 atm. CERAMICS LIFESPAN 1. crucible: approx. 4 – 6 months 2. inductor: approx. 12 weeks The lifespan of the ceramics depends on many factors. The most important are: production frequency, pouring temperature, cleanliness of the liquid metal, and alloy type. The lifespan of the upper cover and rotating cover is much longer because these parts have no direct contact with the liquid metal. PRICE *44,100 EUR *disassembly of the furnace, transportation costs, and assembly at the customer's location are paid by the Buyer; the price includes additional equipment: - additional (replaceable) inductors (without induction coil): 2 pcs.

Condition: used, mileage: 839,600 km, power: 210 kW (285.52 HP), first registration: 11/2009, fuel type: diesel, gearing type: automatic, emission class: euro5, color: white, brakes: retarder, Equipment: air conditioning, parking heater, * Mercedes-Benz Ciatro O530K * Transmission recently renewed * 30+44 seats * 10.6m length * EVOBUS Tjdpsxc Rxysfx Akiod * LAWO destination display * Wheelchair ramp * Air conditioning * Auxiliary heater * Tachograph * Euro 5 * Subject to prior sale, errors and alterations excepted

Condition: new, Year of construction: 2026, operating hours: 1,000 h, functionality: fully functional, machine/vehicle number: SCR 44 2SF, NEW 2026 – REM SC 44 CNC 2SF | Heavy-Duty CNC Vertical Turning Center Top-of-the-range CNC Vertical Turning Center from REM Bacau, featuring dual milling heads, dual automatic tool changers and Siemens Sinumerik 840D SL control. Built for the most demanding heavy machining applications. TURNING ENVELOPE: • Faceplate Diameter: 4,000 mm • Machining Diameter: 4,400 mm • Machining Height: 2,000 mm Todpfxsg Uwmqj Akied • Max. Workpiece Weight: 16,000 kg AXIS TRAVELS: • X-Axis (Ram Carriage): 2,500 mm • W-Axis (Elevating Cross Rail): 1,200 mm • Z-Axis (Ram Vertical Travel): 1,250 mm • Indexing Step: 300 mm WORK TABLE: • Diameter: 4,000 mm | Speed: 1–60 (90) rpm • Power (S1): 100 kW | Torque: 110,000 Nm • C-Axis: 0.02–1.5 rpm | C-Axis Torque: 55,000 Nm MILLING RAM (250×250 mm | KM 63 / ISO 50): • Ram Speed: 0–2,500 rpm | Power: 40 kW | Torque: 1,400 Nm TOOLING: • 2× ATC Magazine (12 turning + 12 milling tools each) • Control: Siemens Sinumerik 840D SL Manufactured by REM Bacau – Romania | 60+ years of expertise. Fully inspected and tested. Export worldwide. Contact us for pricing, videos, and full specs.

Condition: used, Year of construction: 2006, - 528345 Safety device - 528110 CNC central lubrication system - 529166 Central extraction system - 529214 24-position tool changer - 528837 Work table with supports Tedpfoz Algfox Akiod - 528716 16x TV vacuum cups, 145x145 mm - 528717 8x TV vacuum cups, 145x50 mm - 528719 6 positioning aids - 528200 2 cross lasers - 528715 Preparation for clamping cylinder - 528600 Clamping cylinder, Morbidelli - 528121 Vacuum pump - 529207 Reinforced inverter - 528487 Drilling head speed controlled via machine inverter - 523025 Dongle for Xilog - 528409 Software preparation for teleservice - 529334 Clearance height 280 mm - 528525 PC control Storage location: Nattheim

Condition: used, Year of construction: 2011, X-Y working area: 4,422 x 1,753 mm X-Y travel: 4,955 x 1,918 mm Z-axis travel: Z = 400 mm 5-axis MORBIDELLI milling spindle C-axis rotation: 650° B-axis tilt: 290° (-10°) Power: 11 kW at 20,000 rpm, adjustable via inverter Liquid cooling HSK 63F interface Chip conveyor Automatic CNC central lubrication RAPID 24 tool changer (24 tool positions) Drill head extension with 30 + 6 spindles 8 positioning aids 2 cross lasers Vacuum pump 250 m³/h PC control with Windows Office Weight approx. 5,000 kg Storage location: Customer Todpey D Rv Dofx Akijd

Condition: ready for operation (used), bar length: 4,400 mm, overall weight: 900 kg, Bar diameter Ø 5-45 mm Magazine capacity 280 Min. bar changeover time 27 sec. Feed rate 150 mm/sec., adjustable Todpsw Rfkbofx Akijd Return speed 950 mm/sec. Supply voltage 230/400 Volt Installed power 3 KW Compressed air 6 bar Weight 900 kg

Condition: used, Year of construction: 2000, Motor: 7.5 kW Tersa cutterhead, Z = 4 2x sliding rollers in the thicknessing table, height-adjustable Steel feed roller, ribbed Infeed roller before and after the thicknessing table Safety bar Cutterhead speed: 5000 rpm Planing height: 2.8 - 250 mm with digital display Planing width: 630 mm Max. chip removal: 8 mm Dust extraction port: 160 mm Weight: approx. 1115 kg Dimensions: 1140 x 1260 x 1200 mm Storage location: Nattheim Tjdpfj Aay D Rox Akijd

Condition: good (used), Stephan Cutter, Model 44 400 V Tjdpfxoz D Dvxe Akiod

Condition: excellent (used), functionality: fully functional, overall weight: 175 kg, volume flow: 80 m³/h, final pressure: 0.06 bar, input voltage: 400 V, rotational speed (max.): 1,500 rpm, Busch Mink MM 1144B V03 Vacuum Pump Todez Hbqxjpfx Akisd 2 pumps available with very little work done each. Pumps were purchased and installed for a project that was never commissioned. Selling on behalf of our customer.

Condition: used, mileage: 450,175 km, power: 182 kW (247.45 HP), first registration: 12/2017, fuel type: diesel, number of seats: 44, gearing type: automatic, next inspection (TÜV): 07/2027, emission class: euro6, color: white, Year of construction: 2017, Equipment: ABS, air conditioning, 7 UNITS AVAILABLE. Tjdpfxsz I H Ire Akied

Condition: excellent (used), Year of construction: 2001, Complete skid mounted unit with: 1) Infeed trolley/Wagon with 2 stainless steel augers pushing the product into a Positive Rotary piston Pump for ingredients like: Grinded cheese, butter, vegetable fatt, salts etc a cold premixed blend. 2) Steam injection system to heat to 80°C with pump on outlet. 3) 2de heating: 95/140°C This high Ultra high heating module can by by-passed by switching 2 swingbend panels 4) Holding tube 5) Flow diversion valve (no product can pass if temperature not achieved) 6) Flashcreaming module, Vessel of 44ltr combined cooler for rapid cooling and creaming in one. 7) Viscosity measuring system with pump and sensor to check the viscosity. 8) Centrifugal CIP pump 9) Scid mounted with all needed inter connecting piping, sensors and valves. 10) Controls Siemens S5 and operator panel. The UHT System is a compact, skid mounted modular line-process system designed especially for lab or small scale industrial production Tsdszdrufspfx Akisd

Condition: like new (used), Year of construction: 2001, functionality: fully functional, Folding machine Stahfolder TD 78/44 complete with VFZ 52D knife, Rotary Year: 2001 Condition: as new Available in our showroom Tjdoy R R S Sepfx Akijd

Condition: used, mileage: 567,000 km, power: 309 kW (420.12 HP), first registration: 10/2007, fuel type: diesel, overall weight: 32,000 kg, axle configuration: > 3 axles, brakes: retarder, color: white, gearing type: mechanical, loading space length: 5,350 mm, loading space width: 2,450 mm, loading space height: 800 mm, Year of construction: 2007, Equipment: ABS, crane, Renault Kerax 420 DCI Tipper 5,35 m + CRANE + REMOTE CONTROL Accident-FREE IN GOOD CONDITION! ? YEAR OF PRODUCTION: 2007 ? MILAGE: 567 000 km EQUIPMENT: ? ABS ? C. LOCKING ? EL. WINDOWS ? EL. MIRRORS ? POWER STEERING ? TACHOGRAPH TIPPER: 535 x 245 x 80 cm (L x W x H) CAPACITY: 14 000 kg TOTAL WEIGHT: 32 000 kg WHEELBASE: 175/247/135 cm TIRE SIZE: 13R22,5 SPRING SUSPENSION ON BOTH AXLE CRANE: PALFINGER PK 44 002 + REMOTE CONTROL TEL: KUBA - POLSKI, ENGLISH, DEUTSCH, ITALIANO SEBASTIAN - POLSKI, DEUTSCH, ITALIANO, ????? LASZLO - MAGYAR COSTEL - ROMÂN? (Romana facem toate formalitatile pt export inclusiv nr) RADEK - ????? : 4521 Tjdpfezrkm Ajx Akijd

Condition: excellent (used), Year of construction: 2015, Extraction unit HURRICAN JSS-3-6-44-800, year of manufacture 2007/2015. Current air volume flow: 87,900 m3/h. Filter area: 796 m2. Maximum surface load: 130 m3/m2/h. Reserve capacity: 15,800 m3/h. Length approx. 8,950 mm + return air. Width: 2,950 mm. Height: 9,720 mm. Dust type: wood chips/dust. Todpfov Dfr Usx Akied

Condition: used, functionality: fully functional, machine/vehicle number: 109116063, Paolo Orizio S.p.A. single-sided circular knitting machine, model JSV-R, machine number 109116063. Made in Italy. MACHINE PLATE DATA: · Diameter: 30 inches · Gauge: 20 needles per inch · Number of needles: 1856 · Number of feeders: 44 · Cylinder number: 22101088 · Needles: VO 12362 G02 · Belt: Goodyear 200 S 8 M 2032 · No CE marking Todpszvm Ukjfx Akied APPLICATION: Single-sided knit fabrics: plain jersey, pique, fleece, and derivatives for outerwear, sportswear, and underwear. EQUIPMENT INSTALLED: · Orizio control panel with counter and pre-selection · Labeled indicator light panel · IG455 tachometer · UNIWAVE mist lubricator with pressure gauge and regulator · Drive with stepped pulleys · Complete upper fileta · Hour meter LUBRICATION: Oils specified on the plate: Optimol Optigear 5150 / Shell Omala 220. CONDITION: Complete and assembled machine. A visit can be arranged for inspection and on-site operating test. DIMENSIONS AND TRANSPORT: · Approximate dimensions: length 2.70 m · width 2.00 m · height 2.70 m · No disassembly required · Location: Albacete, Spain

Condition: used, functionality: fully functional, Year of construction: 2012, operating hours: 9,039 h, load capacity: 1,700 kg, lifting height: 7,100 mm, free lift: 2,340 mm, fuel type: electric, mast type: triplex, construction height: 2,900 mm, fork length: 1,150 mm, drive type: Elektro, Reach truck Load center: 600 ISO class: ISO Class 2 = 1,000 - 2,500 kg Mast type: Triplex Transmission: Electromechanical Condition: Ready for operation and fully functional Technical condition: very good Front tire type: Vulkollan Rear tire type: Vulkollan Battery voltage: 48V Battery Ah: 620Ah Tjdpfxszvr Nto Akijd Battery manufacturer: Stuba Battery type: PzS Battery year of manufacture: 2024 Description: In addition to this unit, we offer other forklifts and warehouse equipment. Our equipment is workshop and FEM4.004 certified. Please contact us by email or by phone. You can also find us at hsr-gabelstapler. Of course, we also purchase your used equipment, even if you do not buy a vehicle from us. Lease purchase and financing at favorable conditions are available upon request. We will gladly provide you with competent and detailed advice on our vehicles. Side shifter, 3rd valve, full free lift, safety light, non-marking tires, joystick, single pedal, 3-wheel, seat.

Condition: used, Year of construction: 2016, operating hours: 1,427 h, load capacity: 800 kg, lifting height: 1,580 mm, fuel type: electric, construction height: 1,860 mm, gearing type: automatic, overall weight: 679 kg, empty load weight: 495 kg, total length: 1,777 mm, color: red, mileage: 1,427 km, first registration: 09/2016, suspension: other, number of seats: 1, driver cabin: other, emission class: none, fuel: electricity, The BT SWE 080L is a reliable high-lift pallet truck designed for professional use in warehouses, logistics, and production facilities. This model combines robust engineering, superior maneuverability, and an especially compact design—ideal for efficient workflows in daily operations. Thanks to its automatic transmission, operation is particularly comfortable and precise. The stacker can be controlled with high sensitivity, enabling safe driving and lifting movements, even during frequent maneuvering or in narrow warehouse aisles. This allows pallets to be moved quickly, safely, and efficiently. With only 1,427 operating hours, this vehicle is in excellent working condition. First registered in September 2016, it features proven and durable technology, specifically developed for demanding, everyday workplace environments. Tsdpfx Aoyigpmokisd The battery, dating from 04/2021, ensures reliable power supply and stable operating times in warehouse use. This means the stacker remains powerful and ready for operation, even under intensive use. With a lift height of 1,580 mm, the BT SWE 080L is ideally suited for the safe loading and unloading of pallets on low to mid-level racking. Its compact dimensions—with a length of 1,777 mm, a width of only 726 mm, and a height of 1,863 mm—ensure that even narrow warehouse aisles can be easily navigated. Sale only to commercial customers (agriculture, freelancers, small and large businesses) or for export. Subject to prior sale and errors excepted.

Year of construction: 2018, condition: used, machine/vehicle number: AT89, Used Tetra Pak helix accumulator 44 meters year 2018 The Used Tetra Pak helix accumulator 44 meters year 2018 efficiently accumulates and manages the production flow in aseptic packaging lines. Notably, Tetra Pak manufactured this model, identified as ACHX10-0400-44, in 2018 to handle brick-type carton containers. Technical and Functional Features To begin with, the Used Tetra Pak helix accumulator 44 meters year 2018 accumulates containers using a helical system that extends 44 meters. Its primary function is to compensate for speed variations between upstream and downstream machines. As a result, it optimizes production flow and prevents plant downtime. Furthermore, the ACHX10-0400-44 model provides high temporary storage capacity and maintains a continuous container flow without compromising structural integrity. Additionally, the helical architecture optimizes available space and reduces footprint compared to other linear accumulation systems. Consequently, thanks to this configuration, the Used Tetra Pak helix accumulator 44 meters year 2018 ensures high operational efficiency with a reduced footprint, making it particularly suitable for lines with complex layouts. Tjdpjyhbxpefx Akied Materials and Compatibility Moreover, the accumulator handles brick-type carton containers, ensuring gentle treatment that prevents deformations or damage to the packaging. In addition, the structure uses corrosion-resistant and easily sanitizable materials, thereby complying with food industry regulations. Similarly, the conveyor belts and internal components minimize friction, ensuring smooth container movement. Integration with the Production Line Importantly, the Used Tetra Pak helix accumulator integrates easily into existing packaging lines. This is primarily due to its compatibility with Tetra Pak filling and sealing machines. In particular, the advanced electronic control system synchronizes with production, dynamically adjusting the accumulation and release speed of containers based on operational needs. Consequently, this mechanism optimizes production flow management and significantly reduces the risk of congestion or slowdowns in the line. Operational Advantages By using the Used Tetra Pak helix accumulator manufacturers can significantly improve production efficiency. Specifically, it reduces machine downtime and optimizes overall plant performance. Furthermore, the compact and modular structure simplifies installation and maintenance, thus lowering operational costs. On top of that, Tetra Pak’s high-quality construction ensures system reliability, reinforcing the robustness and durability of its equipment. Conclusion of this Tetra Pak Accumulator All things considered, the Used Tetra Pak helix accumulator provides an advanced solution for managing production flow in aseptic packaging lines. Thanks to its storage capacity, operational efficiency, and compatibility with Tetra Pak systems, this model serves as an ideal option for plants requiring high performance and reliability in handling brick-type carton containers. Ultimately, it represents a reliable and effective investment for streamlining production processes.

Condition: used, Radial Drilling Machine GSP type 44 T 12 Spindle: CM4 Spindle exit: 300 mm Arm travel: 1000 mm Max height swivel table/spindle nose in height position: 700 mm Max height table/spindle nos ein height position: 1300 mm Tjdpfx Akjz Nxpljiod Swivel table +/- 90 Swivel table dimensions: 1000 x 400 mm Spindle motor: 3,7 kW False table Length 1000 mm x Width 800 mm Auto descent Mechanical locking Lubricant pump Spindle rotation left/right Rotation at 360° around the column Voltage: 380 V Length: 2100 mm Width: 1000 mm Total height in height position: 2700 mm Total height in low position: 2400 mm Weight: approx 2,5 T

Condition: used, mileage: 4,884 km, power: 90 kW (122.37 HP), first registration: 08/2023, fuel type: electric, axle configuration: 4x2, wheelbase: 2,720 mm, fuel: electricity, color: white, gearing type: automatic, number of seats: 2, total length: 4,490 mm, total width: 1,860 mm, total height: 1,840 mm, Equipment: ABS, Android Auto, Apple CarPlay, Bluetooth, air conditioning, airbag, cruise control, electronic stability program (ESP), fog lights, full service history, onboard computer, power assisted steering, power mirror, sliding door, tire pressure monitoring, = Additional Options and Accessories = - Air conditioning - Rear parking sensors - Front parking sensors - Sliding door on the right side - Driver alertness system - Automatic headlight control - Heated exterior mirrors - Passenger airbag - Electrically adjustable exterior mirrors - Electronic brake force distribution - Driver airbag - Height-adjustable driver's seat - Height-adjustable steering wheel - Collision mitigation by braking - LED daytime running lights - Lumbar support - Multifunctional steering wheel - Radio - Radio with DAB - Rain sensor - Rearview camera - Immobilizer - Blind spot monitoring - Traffic sign recognition = Additional Information = General Information Number of doors: 4 Model range: Nov. 2022 - 2026 Cabin: single Technical Information Torque: 245 Nm Drivetrain Range: 293 km Performance Acceleration (0–100): 11.4 s Top speed: 135 km/h Dimensions Length/Height: L1H1 Weights Unladen weight: 1,583 kg Payload: 637 kg GVWR: 2,220 kg Max. towing capacity: 1,500 kg (750 kg unbraked) Battery Existing battery: Purchased Tjdpfsz H T A Hjx Akiod Battery capacity: 44 kWh, Condition: 99% Charging port: Type 2 Suitable for fast charging: no Interior Interior: black Consumption Average energy consumption: 184 kWh/100km Maintenance, History and Condition APK (Technical Inspection): valid until 08.2027 Number of keys: 2 (2 remote controls) Product Safety Manufacturer: Oostland Automobielen Wasaweg 22 9723JD GRONINGEN, NL

Condition: used, Flat Pile Folding Machine Stahl T52/4-4-SAK66 Falzmaschine - Flat Pile Folding Machine Stahl T52/4-4-SAK66 Year 1988 - Serial-No. 36336-88-148120 Folding Size min. 100 x 150mm Folding Size max. 520 x 820mm Folding Type: 1. Unit 4 Buckles - folding width 500mm Tsde Af Amlopfx Akiod 2. Unit 4 Buckles - folding width 500mm Pile height max. 690mm Stream delivery SAK 66 Include Compressor Counter - Control PCS 100 Manuals Included Online-Video-Inspection by WhatsApp - MS Zoom - Telegram On Stock Emskirchen/Nürnberg - Available Immediately - Can be test

Condition: used, Year of construction: 2021, offer consists of: TRANSPAK Hercules combination tool H-44-12 Tedpfeu Sr Icox Akisd for PP & PET STRAP - strap width: 12mm - max. tension force: 300kg We can also organize the following for you: packaging, loading, transport ( by ship or plane) including customs

Year of construction: 2023, condition: new, machine/vehicle number: 001, The Stainless Steel Molasses Mixer is an advanced machine designed for homogeneous mixing of raw materials with liquids such as molasses and steam. With its two shafts and high-quality stainless steel construction, this machine offers durability and efficiency in one. The strength of this molasses mixer lies in its ability to deliver a continuous mixing process with an impressive capacity of 60 tons per hour. This makes it ideal for industrial applications where consistent and even mixing of materials is crucial to the production process. The machine's stainless steel construction ensures not only durability but also hygiene, making it suitable for applications in the food industry and other sectors where strict standards apply to materials in contact with products. Whether in the production of animal feed, chemical mixtures or other industrial processes, the stainless steel molasses mixer guarantees reliability and consistency in the mixing process, making it a valuable asset for modern production environments. Power:2 x 22 kW Speed:1500 rpm 2. volume: 600 liters 3. capacity:60 Tons/Hour Tsdpfx Ajrk Ipnekisd 4. weight: 2500 kg

Condition: like new (used), functionality: fully functional, HBS 840-44-E Bark Shredder totally renovated and as good as new Tedpfx Aoi E Tkwokiod