Baler

Paal Pacomat II

Condition: excellent (used), Year of construction: 2023, operating hours: 1,851 h, functionality: fully functional, pressing force: 70 t, filling opening width: 1,100 mm, filling opening length: 1,400 mm, bale width: 1,100 mm, bale height: 750 mm, bale weight: 500 kg, overall weight: 17,000 kg, oil tank capacity: 70 l, Technical data baler: Manufacturer Avermann Maschinenfabrik GmbH & Co. KG, Germany Type AVOS 1410 BS-22/50 Year of construction 2023 Pump operation hours 1,851 hours, as of July 24 Press power main press 70 t (a 70 tonne hydraulic cylinder is installed, special equipment) Specific press force 90,9 N/cm² (a 70 tonne hydraulic cylinder is installed, special equipment) Feed channel 1,400 x 1,000 mm Theoretic cycle time 13 sec Theoretic throughput capacity 266 m³/h Bale size 1,100 x 750 (w x h), the length is variable Drive power 22 kW Connected load 65 kW Tying system 4-fold, vertical, fully automatic Throughput capacity at a bulk weight of 30 kg/cbm approx. 5,5 t/h bulk weight of 50 kg/cbm approx. 7,5 t/h bulk weight of 100 kg/cbm approx. 9,7 t/h Bale weight with a bale length of approx. 1.2 m up to 500 kg, depends on material SPS controller Siemens S7-1500 Operating panel Schneider Harmony Baler dimensions built up 8,610 x 2,400 x 3,835 mm (l x w x h) Transport weight baler approx. 17 t Special equipment: Wear-resistant floor made of HARDOX steel Larger main hydraulic cylinder with 70 tonnes of pressing force Special press ram for pressing loose bulk materials with small grain sizes OptiCut XS system for lower cutting forces and higher throughput rates Special pressing piston for pressing "difficult" materials Technical data for the conveyor belt: Manufacturer Avermann Maschinenfabrik GmbH & Co. KG, Deutschland Type KGF GB 1500 Year of construction 2023 Drive power 4.0 kW Belt speed approx. 0.3 m/second Length feeding conveyor 2,679 mm Length elevating conveyor 6,866 mm Length goose neck 1,272 mm Grade 35° Effecting width 1,400 mm Side wall height 800 mm Carrier height 50 mm Carrier distance 750 mm Belt quality EP 400/3, 3:1 (DIN quality N) Overall height 4,515 mm Overall transport dimensions11,148 x 2,502 mm (l x w) Prsdpfx Agsu Thbxo Ded Technical data on the non-contact personal protection system: Manufacturer BOREMA Umwelttechnik AG, Switzerland Type APSS iBOR 22 Year of construction 2023 Condition of the press system: The entire system is in very good condition due to the short operating time of only 1,851 pump hours and the processing of only paper, cardboard and film. Scope of delivery: Avermann baler, type AVOS 1410 BS-22/50, incl. wire drawing stations and bale chute Avermann conveyor belt, type KGF GB 1500 BOREMA personal protection system, type APSS iBOR 22 Comments: The documentation (Manual, CE-declaration, electr./hydr.-drawings), are completely available. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors.

Condition: used, Year of construction: 2009, operating hours: 20,536 h, pressing force: 80 t, filling opening width: 1,100 mm, filling opening length: 1,400 mm, bale width: 1,100 mm, bale height: 750 mm, bale weight: 600 kg, empty load weight: 16,000 kg, Technical data baler: Manufacturer Avermann Maschinenfabrik GmbH & Co. KG, Germany Type AVOS 1410-45/80 Year of construction 2009 Operation hours 20,536 hours, as of September 2024 Press power main press 80kN Specific press force 103,9 N/cm² Feed channel 1,400 x 1,000 mm Theoretic cycle time 12 sec Theoretic throughput capacity 300 m³/h Bale size 1,100 x 750 (w x h), the length is variable Drive power 45 kW Connected load 75 kW Tying system 4-fold, vertical, fully automatic Throughput capacity at a bulk weight of 30 kg/cbm approx. 6,0 t/h Pjdpfxju Thyps Ag Dord bulk weight of 50 kg/cbm approx. 10,5 t/h bulk weight of 100 kg/cbm approx. 17,5 t/h Bale weight with a bale length of approx. 1.2 m up to 600 kg, depends on material SPS controller Siemens S7-300 Operating panel pulsotronic Baler dimensions built up 8,610 x 2,400 x 3,835 mm (l x w x h) Transport weight baler approx. 16 t Special equipment: Wear-resistant floor made of HARDOX steel Special press ram for pressing ‘difficult’ materials and loose bulk materials with small grain sizes Control cabinet air conditioning Machine foot elevation 200 mm Remark: The machine is currently in our workshop undergoing partial refurbishment. We expect the refurbishment work on the machine to be completed by the end of October, after which the machine will be tested and released for sale.

Condition: used, Year of construction: 2009, operating hours: 6,164 h, Doppstadt IDC000123 - manufacturer: Doppsttadt - model: DZ 750 Kombi - year of production: 2009 - gross vehicle weight: 46 000 kg Psdjvy S Dpjpfx Ag Dsrd - working hours: 6145

Condition: used, ALREADY DISMANTLED ‼️ IMMEDIATELY AVAILABLE ‼️ 🔥 Gilles 300 kW Wood Chip Boiler for sale – reliable industrial biomass technology! 🔥 Industrial-scale heating solution with Austrian precision! The Gilles 300 kW boiler is the ideal choice for large facilities, sites, grain dryers, or central heating systems. Key features: 🌲 Fuels: wood chips, pellets, biomass – wide fuel variety ⚡ 300 kW heating capacity – reliable and efficient for heavy-duty users 🔄 Automatic feeding, combustion control, ash removal – minimal personnel required 🧠 Modern control system, optimized combustion ♻️ High efficiency, low emissions 🇦🇹 Gilles = Austrian quality, industrial reliability Psdjp Am Rgspfx Ag Dord 💥💰 PRICE: 9,900 EUR – GOOD CONDITION, READY FOR INDUSTRIAL USE! 💰💥 📍 Location: Hungary, 9200 Mosonmagyaróvár, Kötöttárugyári út 22 (ProfiKazán) ⸻ 💼 Top Heating Systems – ProfiKazán Industrial boilers, biomass solutions, experienced and competent.

Condition: good (used), Year of construction: 1992, functionality: unexamined, overall weight: 18,000 kg, power: 250 kW (339.91 HP), For bulky waste, pallets, residual wood, etc. Single-shaft shredder with electrohydraulic drive Rotor width: 2500 mm Rotor diameter: approx. 500 mm Psdeq I Rkdjpfx Ag Dsrd Electric motor: 250 kW

Condition: ready for operation (used), Baler Hsm vk 42/1200 fully automatic Pressure force: 42 tons Predpfxjra Nrxe Ag Ded Beam dimensions: 700 x 800 x 600 - 1200 mm Beam weight: approx. 450 kg Press length approx. 7 meters press weight approx. 6000 kg tying 4 x wire automatically

Condition: excellent (used), Year of construction: 2006, operating hours: 2,632 h, functionality: fully functional, machine/vehicle number: 29.381, pressing force: 35 t, filling opening width: 620 mm, filling opening length: 1,000 mm, total width: 2,380 mm, total height: 2,500 mm, total length: 6,625 mm, Including feed belt. The machine is immediately ready for operation. Prodpovaw T Ajfx Ag Dsd

Year of construction: 2018, condition: excellent (used), functionality: fully functional, Wemhöner VARIOPRESS Vacuum Membrane Press Basic 1000 S Technical Specifications: Heating platen size (mm): 2850 x 1550 Electric heating platen design: Aluminum, top heating platen Total pressing force (kN): 2400 Max. chamber pressure (bar): 6 Max. operating temperature: 180 degrees Celsius Max. batch or workpiece size (mm): approx. 2460 x 1180 Thermoplastic film in roll form: Film width: approx. 1430 mm Podpfx Agov Np H Hj Dord Film thickness (mm): approx. 0.25 - 1 Pressure chamber height (mm): max. up to 180 Connected loads: Installed power (kW): approx. 46 Required air pressure (bar): approx. 8

Condition: used, Year of construction: 2007, HOLZ-HER – 6310 CUT 110 580 Computer-controlled Panel Saw Watch the video of the machine: Year of manufacture: 2007 Machine number: 136 The machine has been overhauled in all essential mechanical components. Pjdjw I Uxpjpfx Ag Derd New PC, new label printer, etc. in 2023 Technical Specifications and Description: Base machine: Pressure beam saw Version: Fence on the right Saw cycle: away from the fence Cutting length: 5,850 mm Cutting width: 5,850 mm Saw Blades: Main saw blade Ø 400 x 4.4 x 30 mm, Z72, FZ/TZ (not included!) Tungsten carbide pre-scoring blade Ø 180 x 4.4/5.4 x 30 mm, conical (not included!) Cutting Height Cutting height: 110 mm Saw blade projection: 120 mm Pressure beam: pneumatic, pressure adjustable Extraction: Central moving dust channel on the unit Extraction port base machine: 1x Ø 160 mm, positioned on the right side Dust channel in pressure beam: 2x Ø 120 mm – 1x top left, 1x top right with cutting length 5,850 mm: 3x Ø 120 mm – 1x top left, 1x top center, 1x top right Extraction air velocity: 30 m/s Air volume: 4,000 m³/h at 30 m/s Compressed Air Air consumption approx. 32 l/min at 6 bar per cutting cycle Switchable collet chuck pressure Switchable from the control panel For sensitive panel materials Automatic cutting length limitation The saw unit detects the workpiece end using a non-contact sensor and optimizes the cutting cycle Offcut device For cutting without leftover piece Clamps retract into recessed pressure beam Width Stop Precision-guided, freely programmable width stop with clamps Rack-and-pinion drive for precise positioning With surface-hardened linear guides Return speed of panel pusher: 80 m/min Forward speed of panel pusher: 80 m/min (EU – max. permissible forward speed 25 m/min) Max. opening for clamps: 120 mm for longitudinal and cross cuts Clamps, floating design Compensate for internal stress in panel packs upwards – 6 pcs for 3,250 mm cutting length – 7 pcs for 4,250 mm cutting length – 8 pcs for 5,850 mm cutting length Control CUTCONTROL 2 with 15" TFT display Operating system Windows 2000 RJ45 network connection 10/100 Base-T Fast Ethernet Intel Celeron processor Midi tower US keyboard Optical mouse CD ROM drive Control panel located on fence side Clearly arranged graphic-based operator interface for easy handling and order/material management on Windows basis Realtime display Large, clearly structured buttons All functions accessible from one level No limits in input fields and unlimited job inputs possible Control Functions Direct Cut: Cutting by direct entry of cutting dimensions. Processing of absolute, serial, or format cuts, with integrated grooving, notching, or positioning cuts. Unlimited jobs programmable. Job prioritization (prioritization possible at any time). Order programming parallel to cutting. NC Cut: Processing of optimized jobs. Graphical machine overview with machine process flow function ...

Condition: defective spare-parts repository (used), Year of construction: 2013, Manufacturer: HSM Tip: HL 4010 Li Year of construction: 2013 The equipment is incomplete and is sold as a part Fault: Hydraulic pump missing Control is missing Prsdpeur Ravofx Ag Djd Power supply unit missing