Used Operating Resolution for sale (30,923)

Condition: used, Year of construction: 2002, grinding diameter 450 mm grinding length 1500 mm centre height 225 mm Control FAGOR EQUIPEMENT - T1: grinding wheel diameter 500 mm - T2: grinding wheel diameter 400 mm - T6: HF Fischer spindle MFV or MFZ 1224/1242/1260 - T7: HF Fischer spindle MFV or MFZ 1224/1242/1260 - Marposs tool measurement - active longitudinal positioning - Elaso GAP-control on T1 and T2 contactless integrated in the control surface - Elaso GAP internal grinding with fluid sensor for T6 and T7 - semi-automatic balancing by Elaso integrated in the control surface for T1/T2 - tailstock hydraulic with fine adjustment +/- 150 microns - dresser on workpiece spindle side table mounted - dresser on tailstock side table mounted - dresser on upper table - new service- and userfriendly housing Gksdpfx Aisuxfu Nsvoc SPECIAL EQUPEMENT: Workhead with direct drive - strongly recommended for non-circular grinding - workpiece weight flying max. 75kg - workpiece weight between centres 150kg - water-cooled B-axis with direct drive - center height 225 mm - extremely torsionally stiff - highly accurate positioning - resolution ° - water-cooled Hydrostatic ball screw - x-axis - wear-free, as there is no contact during operation - no loss of precision, even during long-term use at full load and maximum speed - no friction at low speeds - no friction force backlash when the direction of rotation changes - translates even the smallest rotational movements - no stick-slip effect even at low speeds - no fluctuations in frictional torque due to ball circulation - higher axial stiffness compared to ball screws - significant improvement in damping, resulting in better workpiece surface finish and tool life - no oscillations due to ball circulation - also suitable for high speeds and accelerations - cost-effective alternative to the linear motor with greater precision and significantly lower heat generation - significantly less power dissipation and, as a result, no problems with swarf on permanent magnets New hydraulic unit - optimized temperature control (chiller) - Energy-saving Only one pump controlled by VFD - Pressure monitoring - monitoring of the hydrostatic oil for water content. (Damage to the bellows is recognised and detected prematurely) -fine adjustment +/- 150 microns Paper belt filter 375l – alternative 480l Grinding mist extraction system – emulsion MECHANICAL OVERHAUL -complete machine according to Kellenberger protocoll -new painting ELECTRICAL OVERHAUL - new modern Fagor CNC with BEMA HMI - new electric cabinet - new digital drive technology - replacement of all electrical cables, switches etc. - new absolute external scales in x- and z-axis - new absolute encoder (B-axis) Grinding software BEMA-Standard: - workpiece zeroing - grinding wheel zeroing - dressing diamond measuring - corrections - external and internal surface grinding - external and internal angle grinding (turning of the b-axis, dressing with straight wheel) - external and internal radius grinding (radius dressed on wheel) - semi-automatic traverse grinding - workpiece zeroing - 2 dressing diamonds - 1 dressing blade - dressing roll - 3 flat dresser - corrections - Z-position measurement - GAP control Optional grinding cycles at no extra charge: Profile plunge grinding: - external and internal profile plunge grinding with profile wheel Pr...

Condition: used, grinding diameter 350 mm grinding length 1500 mm centre height 175 mm total power requirement 5,5 kW 500mm grinding wheel diameter New servomotors in x and for the workhead. Photo of already delivered machine in UR equipment. -Operation via the touch panel is extremely simple. -The symbols on the control panel are practically identical to the original original control system, so there is no need for training. -Diagnostic function with display of PLC information and digital I/O -Dressing function can be extended or changed at the customer's request. -Oriented spindle stop of the workpiece spindle possible on request. -New maximum infeed of 40 mm can be extended on request. -Digital display in 2 axes. Resolution x-axis 0.5my Options: -Rotary encoder with digital display in the workpiece headstock -Rotary encoder with digital display in the grinding headstock (no height adjustment with spindle possible) with spindle possible) -Increase of the center height to max. 225mm -Speed control for the grinding spindle Translated with (free version) Gjdpjuwv Idsfx Aivekc

Condition: like new (used), Year of construction: 2021, functionality: fully functional, Equipment: documentation/manual, We offer for sale a professional digital microscope, the KEYENCE VHX-7000, a state-of-the-art device designed for detailed visual inspection, measurement, and analysis of materials and components. Godpfx Asz Ng Ntoivokc This microscope is ideal for industrial companies, laboratories, research institutions, quality control departments, and technical universities. 🔍 Main advantages and features: • ✅ High-resolution digital imaging • ✅ Advanced 2D and 3D surface imaging • ✅ Large depth of field and automatic focusing • ✅ Precise measurement of dimensions and surface analysis • ✅ Advanced lighting options and detail enhancement • ✅ Simple and intuitive operation • ✅ Capability for documentation, archiving, and evaluation of results • ✅ Suitable for quality control, research, and development 🏭 Application areas: • Automotive and mechanical engineering • Electrical engineering and electronics • Metallurgy and materials engineering • Quality control and analysis of manufacturing defects • Research, development, and laboratory measurements 📦 Device information: Manufacturer: KEYENCE Model: VHX-7000 Type: Professional digital microscope

Condition: ready for operation (used), Year of construction: 2014, Printing technology: piezo DOD printheads: Xaar 1001, resolution: 720x360dpi, drying: 1xUV GOZ and 1xUV FOZ Höhnle with 7,2kW, pinning system (LED) after printing unit 1+5, extraction: in the drying unit for cooling the UV lamps and for odor minimization and improvement of sensory conditions, inert gas system: oxygen-reduced curing unit (inert gas system), consumption: under 6m³/h, printing: roll-to-roll, web width: 350mm, print width: 330mm, repeat length: min./max. printable section length 10-1000mm, print tolerance: single spacing +/-0,2mm, cumulative spacing: +/-1,5mm (over one meter), register: register accuracy +/-50μm, max. speed: 48m/min with 4 colors depending on ink coverage, white at 30m/min, speed must be preselected from 18 to 48m/min, print pre-treatment: corona with 1500VA, web cleaning: polymer rollers LC 350, air shafts: for cores with 76mm diameter for unwinding and rewinding, air shaft clamping pneumatic, clamping releasable to allow rotation of the winding mandrel, max. roll diameter for unwinding and rewinding: 610mm, max. roll weight for unwinding and rewinding: 120kg. power consumption: approx. 39kVA/60A, air consumption: 100NL/min, cooling capacity: approx. 60.000BTU/h =18kW, data interface: USB2.0, Ethernet, data format: PDF-X1 or X3 or EPS or AI, length: 4550mm, width: 1750mm, height: 2200mm, weight: approx. 3t. With documentation, chiller unit and inks. The machine is fault-free, complete and ready for operation, and has been serviced regularly. On-site inspection is possible. Godpfexz Ewnex Aivskc

Year of construction: 2021, condition: excellent (used), Memmert ICH 260L chamber from 2021. The unit comes with a one-year warranty on spare parts. Manufacturer's description: Temperature Operating temperature range without humidity: 0 to +60 °C Temperature setting range 0 to +60 °C Operating temperature range from +10 °C to +60 °C with humidity and/or light Temperature setting accuracy 0.1 °C Temperature sensor 2 Pt100 DIN Class A sensors in a 4-wire circuit for mutual monitoring, taking over functions in case of an error Humidity Humidity humidity supply using distilled water from an external tank via a self-priming pump Humidification humidification using a hot steam generator Humidity active humidification and dehumidification of the air, adjustable in the range of 10-80% relative humidity with a digital display of relative humidity - display resolution 0.1%, setting accuracy 0.5% Light Daylight and ultraviolet light can be programmed individually using the controller Light cold white light +/- 6%, for UV light +/- 10% Light Gkedpfxezam Hij Aivjc lighting unit consisting of 4 cold white fluorescent lamps (standard D65 lighting, 6500 K) and 2 UV lamps in the spectral range of 320-400 nm

Condition: ready for operation (used), Year of construction: 2013, operating hours: 7,358 h, functionality: fully functional, machine/vehicle number: 6LUD00036, travel distance X-axis: 620 mm, travel distance Y-axis: 520 mm, travel distance Z-axis: 460 mm, feed length X-axis: 620 mm, feed length Y-axis: 620 mm, feed length Z-axis: 460 mm, feed rate X-axis: 36,000 m/min, feed rate Y-axis: 36,000 m/min, feed rate Z-axis: 36,000 m/min, torque: 108 Nm, controller manufacturer: Heidenhain, controller model: iTNC530, workpiece length (max.): 500 mm, workpiece width (max.): 400 mm, workpiece height (max.): 350 mm, workpiece diameter (max.): 680 mm, workpiece weight (max.): 300 kg, total height: 3,400 mm, total length: 4,600 mm, total width: 2,700 mm, table width: 600 mm, table height: 755 mm, table length: 600 mm, table load: 300 kg, rotary table diameter: 600 mm, rotational speed (min.): 20 rpm, rotational speed (max.): 12,000 rpm, overall weight: 8,500 kg, spindle speed (min.): 20 rpm, spindle speed (max.): 12,000 rpm, operating hours of spindle: 5,303 h, coolant supply: 18 bar, distance table center to spindle nose: 50 mm, spindle motor power: 17,000 W, spindle nose: SK40, number of spindles: 1, number of slots in tool magazine: 100, input voltage: 400 V, type of input current: three-phase, Equipment: chip conveyor, documentation/manual, Commissioned 4/2014 Table rotation, C-axis: 360° Table swivel, B-axis: -50° to +110° Distance from spindle nose to table: 150 mm Table clamping surface: Ø 650 Table load capacity, max.: 300 kg Table slots: 5 x 18H7 x 100 mm Centering bore: Ø 50 H7 x 30 mm Workpiece size, max.: Ø 520 x 330 mm Machine accuracy: VDI I DGQ 3441* Positioning accuracy: +/- 0.006 mm* Axis resolution: 0.001 mm* *determined at a constant ambient temperature of 20°C +/- 1°C Main spindle: Main drive, AC motor, direct drive Drive power (100% / 25% ED): 10.0 / 17.0 kW Speed range, stepless: 20 - 12000 rpm Spindle taper: SK 40 DIN 69871 Torque at (100% / ED): 63.7 / 108.6 Nm Axis drives: Axes X, Y, Z: AC motors Axes B, C: AC motors Travel speeds: Rapid traverse in axes X, Y, Z: 36 m/min Speed, max. B-axis: 25 rpm Speed, max. C-axis: 25 rpm Acceleration X, Y, Z: 6.5 m/s² Coolant system: External tool cooling via external nozzles Coolant tank: 280 l Operating pressure, external: 0.9 bar Coolant system, internal tool cooling DIN 69871 Form A Gedoz Diq Uepfx Aivjkc Operating pressure, internal coolant supply: 18.0 bar Manual rinsing of the work area via an additional gun Standard accessories: - CNC control: Heidenhain iTNC 530, full simultaneous 5-axis version - Handwheel 410 (Heidenhain) - Digital axis drives - Digital spindle drive - Swarf conveyor with discharge height 800 mm • Spindle cooling – radiators – plate cooling for spindle motor - Full protective enclosure with cabin roof Tool magazine VZG 65 5A by Indunorm: Number of tools: 100, with a tool length of up to 320 mm / can be converted to 125 tools, then a tool length of only 200 mm is possible. Tool diameter, max.: 80 mm Tool diameter, max.: 130 mm (with free adjacent positions) Tool change with double gripper - Linear path measuring system in axes X / Y / Z (glass scale) - Direct encoder in axes B / C - Temperature compensation - IR measuring probe – 3D Software - Option - iTNC 530 Kinematic-Opt • Calibration software Internal tool cooling 18 bar • Coolant tank • Internal tool cooling: 280 L DIN 69871 Form A • Double-circuit filter • Switchable filter cartridges • Filtration rate: 10 µm Band filter system PRODUCTION - LINE - RT 100 Automatic pallet changing system Loading and unloading via a linear axis system: Handling data: Handling weight, max.: 100 kg (35 kg) Pallet capacity: 6 pallet positions up to 400 x 400 mm: Control: PLC control with integrated control cabinet incl. switching and control components incl. software for the automatic sequence Zero point clamping system 320 x 320 x 60 mm - Clamping via 4 clamping bolts - Axis distance: 180 mm - Clamping force: 4 x 12500 N - Repeatability: 0.005 mm - Axial load, max.: 4000 kg • Zero point clamping plate 320 x 320 - Automatic door Interface for automation and clamping systems Universal interface for automatic pallet changing systems, force clamping devices and zero point clamping systems • for pneumatic clamping systems • 2-channel rotary feedthrough integrated in the table • Pneumatic lines led to the outside • Pneumatic maintenance unit • Control via M commands logical inputs and outputs prepared incl. 7 pallets 320x320 with 6 vices and one 3-jaw chuck !!without tool holders and without tools!! Machine ex works, without delivery and assembly, all information without guarantee, price plus statutory value-added tax.

Condition: excellent (used), functionality: fully functional, Year of construction: 2018, operating hours: 2,974 h, load capacity: 2,500 kg, lifting height: 4,900 mm, free lift: 1,318 mm, load center: 600 mm, fuel type: electric, mast type: triplex, construction height: 2,250 mm, motor manufacturer: ELECTRIC, gearing type: hydrostat, battery capacity: 930 Ah, remaining battery capacity: 95 %, battery voltage: 48 V, fork carriage width: 1,400 mm, fork length: 1,150 mm, fork width: 180 mm, fork thickness: 45 mm, tire condition: 100 %, front tire type: cushion tires (black), front tire size: 16 X 7 X 10 1/2, rear tire type: cushion tires (black), rear tire size: 559 / 254 - 406, overall weight: 9,420 kg, empty load weight: 6,920 kg, total height: 2,250 mm, total length: 1,550 mm, total width: 1,500 mm, color: orange, Equipment: CE marking, all wheel drive, cabin, head guard, lighting, pallet forks, sideshift, # COMBILIFT CBE2500 | ELECTRIC | TRIPLEX 4900 MM | FREE LIFT | FORK POSITIONER | FULL CAB | READY TO WORK ## ✅ FULLY SERVICED | WARRANTY | WORLDWIDE DELIVERY Are you looking for a forklift that starts generating value from day one, rather than creating unexpected maintenance costs? The COMBILIFT CBE2500 is fully serviced, thoroughly inspected, and ready for immediate operation. Whether you work in manufacturing, warehousing, steel processing, or timber handling, this machine is prepared to perform from the moment it arrives. --- ## ⭐ Key Advantages ✔ Fully serviced before delivery ✔ Start-up warranty included ✔ Brand-new super elastic tires ✔ Excellent mechanical and cosmetic condition ✔ Ready to work with no additional investment required ✔ Live online video inspection available ✔ Direct delivery to your facility anywhere in the world --- # 📋 Technical Specifications 🏭 Manufacturer: COMBILIFT 📌 Model: CBE2500 📅 Year of Manufacture: 2018 ⚡ Power Type: Electric 🏋️ Load Capacity: 2,500 kg ⏱ Operating Hours: 2,974 h ⬆️ Mast: Triplex 📏 Lift Height: 4,900 mm ↔️ Fork Positioner: 1,400 mm 📐 Fork Length: 1,150 mm 🚜 Cab: Fully Enclosed & Heated ⚖️ Operating Weight: 6,920 kg --- # 📐 Dimensions 📏 Overall Height: 2,250 mm 📏 Overall Length: 1,550 mm 📏 Overall Width: 1,500 mm 📏 Lowered Mast Height: 2,250 mm --- # 🛞 Tires Front: 16 x 7 x 10 1/2 Rear: 559 / 254 - 406 ✅ Condition: 100% Brand New --- # 🔧 Equipment ✅ Fork Positioner ✅ Side Shift ✅ Free Lift ✅ Fully Enclosed Heated Cab ✅ Working Lights --- # 🏭 Ideal Applications 🌲 Timber Industry 🏗 Steel Mills & Steel Service Centers Gkodpfxez R Ap Eo Aivsc 🏭 Structural Steel Manufacturers 📦 Handling Pipes, Profiles & Long Materials 🏢 Indoor & Outdoor Operations --- # 🌍 Why Choose FT LOGISTICS? When you buy from FT LOGISTICS, you are purchasing from a company specializing exclusively in: ✔ Forklifts ✔ Sideloaders ✔ Multidirectional Forklifts ✔ Warehouse Equipment Every machine undergoes a comprehensive technical inspection, professional servicing, and operational testing before delivery. We maintain an inventory of 100+ machines available for immediate shipment and deliver equipment to customers throughout: 🌍 Europe 🌎 South America 🌍 Africa 🌏 Asia 🌍 Middle East --- # 🤝 What We Offer 🔧 Complete Pre-Delivery Service 🛡 Warranty 👨‍🔧 Professional Technical Advice 💳 Leasing & Financing Solutions 🚛 Worldwide Transport 📄 Export Documentation & Customs Clearance 🤝 After-Sales Support --- # 📹 Need More Information? We can provide: 🎥 Live Online Machine Demonstration 📷 Additional High-Resolution Photos 🎬 Detailed Videos 📋 Customized Transport Quotation 🌍 Worldwide Shipping Solutions --- ## ⭐ Why Our Customers Choose Us Hundreds of companies across Europe and worldwide trust FT LOGISTICS for reliable, work-ready equipment. Our customers return because they know they receive professionally prepared machines backed by expert support and international logistics experience. --- # FT LOGISTICS ### 🚛 We Deliver Machines Ready to Work. Professional Forklifts | Sideloaders | Multidirectional Forklifts | Warehouse Equipment | Worldwide Export

Condition: new, Year of construction: 2025, Guowei 68 - available immediately on stock in Europe Product Description： Cutting knife and paperweight are controlled by hydraulic transmission. Fully hydraulic drive makes the machine more secure and imported hydraulic parts ensure the stability of the system. The machine has the function of a reference setting and keeping, and the effectiveness of the reference and self-diagnostic function; infrared protection and hands button interlock protection device; precise paper pusher guide, high precision of alignment and rear angle. Computer system adopts 10-inch colorful full-touch screen, servo motor driven,. The data resolution is 0.01mm, with self-diagnostic function and operation mode display, 100 program groups, more than 10,000 different cutting positions, dynamic tracking, max paper pushing speed 5-10 m / min, and it has imported hydraulic components; electric components from France, Japan, Korea. Its key parts adopt imported bearing of low maintenance. Model / Specifications 68 Cutting width(cm) 68 Max.cutting height without assistance pressing plate(cm) 8 Max.cutting depth(cm) 68 Min cutting depth without assistance pressing plate(cm) 2 Gedpfx Aou Rz S Ieivekc Extended length of working table(cm) 53 Height of working table(cm) 92 Machine width including side working table(cm) 126 Total length of working table(cm) 150 Cutting speed(r/min) 20 Max. Paper pressure(n) 10000 Power of main motor(kw) 2.2 Servo Motor for paper feeding(kw) 0.4 Machine weight(kg) 800 Overall dimension(L × W × H)(cm) 167*137*172

Condition: new, Year of construction: 2026, CKT 400 × 1000 CNC Lathe with Driven Tooling is an advanced CNC turning machine designed for precision machining of metal components in medium and large-scale production facilities. Equipped with the Siemens Sinumerik 808D CNC control system, it provides reliability, high accuracy, and ease of operation, meeting the requirements of modern industrial manufacturing processes. Key Features of the CKT 400 × 1000 CNC Lathe with Driven Tooling The CKT 400 × 1000 CNC metal lathe is a professional industrial solution offering: High machining precision – maximum swing over bed of 400 mm and swing over cross slide of 210 mm, with minimum setting resolution of 0.001 mm on both X and Z axes. Flexible spindle system – spindle speed range of 0–2000 RPM, spindle bore of 52 mm (optional 72 mm), and MT6 spindle taper provide versatility for various machining applications. Intuitive CNC control – Siemens Sinumerik 808D Advanced system with Polish-language interface and Siemens servo drives ensures easy operation and high process reliability. Rigid machine construction – net weight of 2000 kg provides excellent stability during machining of workpieces up to 1000 mm in length. Efficient tooling system – 4-position tool holder with driven tooling (optional 6 or 8 positions), supporting tools up to 20 × 20 mm (optional 25 × 25 mm), enables flexible machining operations. Fast setup and adjustment – convenient tool positioning, work zero setting, and corrections can be performed without writing complete CNC programs. Enhanced operator safety – controlled rapid movements and spindle speed limitation allow precise and safe machine operation. Extended component durability – automatic lubrication system for gears and guideways reduces wear and increases machine service life. Optimized cooling system – ensures thermal stability and protects cutting tools and workpieces during intensive machining. Energy-efficient operation – the 5.5 kW main motor combined with 6 Nm X and Z axis feed motors provides high productivity with optimized energy consumption. Integrated machining cycles – supports operations such as facing, taper turning, threading, and drilling by entering basic parameters without requiring advanced G-code programming knowledge. Customizable configuration – available options include Fanuc Oi-TF control, hydraulic chuck, bar feeder, and CAD/CAM software integration. European safety standards – CE Declaration of Conformity Standard Equipment Gsdpfx Aiov A S N Devekc SIEMENS SINUMERIK 808 Advanced CNC control system with Polish-language interface Siemens servo drives Manual lathe chuck 4-position tool holder with driven tooling Complete set of soft jaws Hydraulic tailstock with MT5 quill Coolant system Automatic lubrication system for gears and guideways 24V halogen work lighting User manual CE Declaration of Conformity Technical Specifications Maximum swing over bed 400 mm Maximum swing over cross slide 210 mm Distance between centers 1000 mm Spindle speed range 0–2000 RPM Spindle bore 52 mm (optional 72 mm) Spindle taper MT6 Tool positions 6 + 1 driven tool Maximum tool size 25 × 25 mm Minimum setting resolution (X / Z axes) 0.001 mm / 0.001 mm X-axis rapid traverse 8 m/min Z-axis rapid traverse 10 m/min Tailstock taper MT5 Maximum tailstock quill travel 120 mm Main motor power 5.5 kW X-axis feed motor 6 Nm Z-axis feed motor 6 Nm Packaging dimensions (L × W × H) 2640 × 1500 × 1770 mm Net weight 2000 kg

Condition: excellent (used), Year of construction: 2019, functionality: fully functional, number of ink cartridges: 4, year of last overhaul: 2025, type of input current: AC, overall weight: 350 kg, Equipment: auto duplex, double-sided, Dear business customers, we hereby offer our Xerox devices in very good condition: Brand: Xerox Product type: All-In-One printer Product line: Xerox Colour Gsdpfxov Dtino Aivskc Model: Color C60 Technology: Laser Maximum resolution: 2400 x 2400 x 1 dpi Special features: Duplex, Fax, Copier, Scanner Output type: Colour Input type: Colour Konnektivität: 10/100/1000BASE-TX B/W print speed: 65/75 ppm Manufacturer code: 3916823303 Supported print formats: A4 (210 x 297 mm), SRA3, A3 (297 x 420 mm) Paper feed: 3260 sheets as standard via four internal trays and additional feeder Manufacturer's warranty: None Country and region of manufacture: Unknown Dimensions: Height: 1391.5 mm - Width: 1574 mm - Depth: 787 mm Compatible operating system: All common Windows operating systems, various MAC operating systems (see data sheet) Scan functions: Scan-to-E-Mail, Scan-to-Folder, Scan-to-PC, Scan-to-Mailbox (private and public), Scan to USB, FTP, SMB, Desk, Searchable PDF, PDF/A, XPS, Thumbnail preview Scan file formats: PDF, XPS® , PCL® -6 emulation, HP-GL2 (direct transfer), TIFF, JPEG, Adobe

Condition: excellent (used), Fully hydraulic high-performance band saw in the heaviest design, with horizontally parallel movable saw blade, for cutting profiles, pipes and solid material in all qualities, including extremely difficult to machine material (e.g. titanium, Inconel, Hastelloy) suitable for the use of bi-metal and hard metal saw blades. Saw unit in a fully solid design made of polymer concrete, this ensures the highest level of smoothness and service life of the saw blades. The saw unit is guided via two vertical square columns (double column guide) with hardened and ground guide rails. Hydraulic saw blade tensioning and hydraulically pre-tensioned hard metal saw blade guides. The material is tensioned via two hydraulic vices. The control system offers simple machine operation. The length can be set using a counter with 0.1 mm resolution. The quantity is set using a quantity counter, which switches the machine off when the quantity is reached. The material is fed via a hydraulic cylinder and ensures maximum cutting accuracy. The machines are easy to operate and work fully automatically. KASTO - fully hydraulic horizontal band saw HBA 420 AU CNC (420 mm x 420 mm / Ø 420 mm) Fully hydraulic high-performance band saw in heavy-duty design, with horizontally parallel movable saw band, for cutting profiles, pipes and solid material in all qualities, including extremely difficult-to-machine materials (e.g. titanium, Inconel, Hastelloy) suitable for the use of bi-metal and hard metal saw bands. The saw unit is made of solid polymer concrete, which ensures the highest level of smoothness and service life of the saw bands. The saw unit is guided by two vertical square columns (double column guide) with hardened and ground guide rails. Hydraulic saw band tensioning and hydraulically pre-tensioned hard metal saw band guides. Material tensioning is carried out via two horizontal frame clamps. Material feed via a non-driven roller conveyor integrated into the machine with twelve transport rollers, which makes it easy to transport short leftover pieces. Cutting area round 420 mm Cutting area square 420x420 mm Material feed with automatic 600 mm Multiple material feed 9999 mm Cutting speed continuously variable 20-130 m/min Total drive power 8 kW Drive power of saw motor 5.5 kW Clamping pressure reduction continuously variable Material support height 700 mm Saw band dimensions 6300x41x1.3 mm Shortest cutting length with automatic operation 6 mm Remaining piece length with automatic operation 100 mm Voltage 400V/50 Hz Dimensions LxWxH 3050x2420x2130 mm Gedpfx Aijvzlgasvokc Weight 2920 kg. Year of manufacture 1995 Accessories: Chip conveyor, coolant system Special accessories: Driven machine roller conveyor CNC control Frequency-controlled drive Material end via Light barrier Cutting speed and feed controlled

Year of construction: 2026, condition: new, functionality: fully functional, Semi-automatic depaneling / basic machine with parallel shuttle The dynamic depaneling machine LOW 4322 XL is especially suited for medium to high product volumes and meets growing demands in the production process. Printed circuit board blanks of various materials are separated using low-dust and low-stress sawing and milling techniques with maximum product flexibility, precision and throughput. Highly dynamic linear motor axes, tools and grippers meet the highest quality requirements and guarantee the depaneling machine a long service life and high reliability. Semiautomatic depaneling - solutions on demand The LOW 4322 XL depanelling machine enables fast product changeover while maintaining short depanelling and handling times. The blank printed circuit board is inserted with a parallel shuttle, picked up and fixed with pin clamping technology and, if necessary, in combination with vacuum suction cups. Made in Germany The machine is equipped with: - a shank and slice tool separation module on Z-axis (automatically rotatable 0-90) - X-Y cross table module in linear motor technology with high-resolution measuring system - 2-compartment loading module built as parallel shuttle, separated left and right with sliding doors - Steel welding frame with two maintenance doors - left and right. ESD - standard vision system base module for teach-in programming - Working area is 520 x 480mm - Automatic cutter length processing Gksdpevuw R Rsfx Aivsc - Remote maintenance/support via remote connection - Touch IPC with Windows 10 Pro operating system - Laser axis measurement incl. protocol - Air ionization - Cutter breakage control for end mills only - Preparation for vacuum clamping technology - ESD powder coating, RAL 9002, disc and sliding doors Optionally a vacuum cleaner unit can be offered later.

Condition: as good as new (ex-display), Year of construction: 2024, Capacity: 5.000 kN Specification: Threshold setting: Reading begins at 1% of capacity (50 kN) Resolution: 10 kN Inaccuracy: +/-0.5 % of Full Scale (F.S.) Non-linearity: +/-0.3% F.S. Non-repeatability: +/-0.l% F.S. Temperature Range: 0° C. to 70° C Temperature Effect on F.S. output: +/-0.001% F.S./DEG. F. on no-load output: No effect (has auto- zero balance circuit) Overload: 150% of capacity (7.500 kN) Sampling rate: Three measurements per second Operation mode: Peak or Track Gedpfefpwk Rox Aivjkc Strokes per minute: Single stroke device, automatic reset on each stroke Power: Standard 9V alkaline battery Approx. 30 hours of continuous use Has low battery indicator Tons Display: 3 1/2 digit LED (0.56" high) Dimensions: app. 230 L x 190 W mm, height app. 180mm Height sets to 7.0000" +/- 0.0005" Weight: app. 32 kg inckuding carrying box with analog output

Year of construction: 2017, condition: excellent (used), Bluhm weber legi-air 4050 labeling machine More pieces in stock! year built: 2016-19 Print resolution 8 dots/mm (203 dpi) 12 dots/mm (300 dpi) 24 dots/mm (600 dpi) Print speed Up to 400 mm per second Tamp sizes (mm) Tamp-Blow standard of 12.5 x 7 to 160 x 300 mm, label lengths must be limited in accordance with label quality, longer or smaller labels are Gkedpofp A I Eefx Aivsc possible using special tamps Label gap Minimum 3 mm Label roll 300 mm diameter, up to 450 running meters, core 76 mm (3"), outside winding (optional inside winding) Data interfaces RS232, RS422, RS485, Ethernet Optional: Profibus Dimensions (L x H x W) 770 x 560 x 580 mm, Applies to system with 250 mm stroke Display controller Multi-language operator guidance 5.7" VGA touch display Service interval indicator Polling, editing and saving of label data USB connection for memory medium or keyboard Compressed air connection 6 bar, the compressed air must be clean, dry and oil-free

Year of construction: 2024, condition: new, The plant is available immediately ! - suitable for log diameters from 10 cm up to 50 cm - suitable for 2 - 6 m log length - 4-strand infeed conveyor 6 m long - 4 - strand separator 2 m long - 4 - strand separator 2 m long - Conveyor with pin conveyor chain M 112 with gentle rollers - block conveyor with 2 inch chain and flights - Special carrier for low-noise transport Godpfsgvu Alex Aivokc - Measurement with 1 mm resolution - Measuring frame with additional heating and sunshield - Display of all operating states on a 17" monitor - Fully automatic sequence control - Various storage options and sorting criteria - 5 ejectors right/left via SEW gear motors with brake - Spacious heat-insulated control cabin - 4 monitoring cameras with flat screen - Control cabinet with all cables - Sorting criteria according to agreement

Condition: as good as new (ex-display), Year of construction: 2021, measuring range X-axis: 500 mm, measuring range Y-axis: 500 mm, measuring range Z-axis: 300 mm, Equipment: documentation/manual, lighting, AIM coordinate measuring centers are the technical successors to the Mahr multisensor coordinate measuring machines currently in use worldwide. Technical data: Godpeg Ewk Refx Aivskc Measuring range: 500 x 500 x 300 mm Dimensions: 1520 x 1040 x 2040 mm Weight: approx. 1,200 kg Maximum workpiece weight: approx. 40 kg on the glass plate Accuracy: U1 = 1.9 + L/200 U2 = 2.4 + L/150 U3 = 2.9 + L/100 (L = measuring length in mm) Increased accuracy available on request Traverse speed: 200 mm/s Acceleration: 400 mm/s Scale resolution: 0.0001 mm Multisensor sensor unit (MSH) optical/tactile/laser - including high-precision USB camera with 2-stage zoom and telecentric beam path - including PTL01 TTL point laser, high-precision, telecentrically coupled - including Renishaw TP200 integrated tactile probe system, optionally expandable - including Quad-Light LED power ring light, programmable illumination - including LED power transmitted light - including Nikon precision objective 5x (optional 3x, 10x, 20x, 50x) C-mount Technology - including calibration standard with factory calibration certificate, consisting of a glass plate "circle", calibration sphere and gauge ring Transfer - state-of-the-art PT200 CNC controller system in a robust, industrial-grade control cabinet - PCI-BUS system for fast internal data transfer in real-time operation - pull-out controller rack 19" for optimal access in the event of service - modular controller concept open for later upgrades and retrofits - service-optimized controller design for quick access and service times - integrated 64-bit broadband bus technology with real-time data transfer - 4-channel online temperature compensation preparation "on board" - active safety technology for drives, light management and sensors - online remote connection for remote maintenance and online system check - LS circuit breakers for quick fault finding in the event of service - firmware adaptation for volumetric 3D full error compensation Including the powerful OptiCheck3D 5.0 software Commissioning, training and start-up support (programming) can be booked as a special package!

Year of construction: 2002, condition: repair required (used), ULMA, year of manufacture 2002 • Extended infeed conveyors. • Centralized lubrication. Gedpsg H Tquefx Aivjkc • Sanitary clean out the tray. • Gravity and motorized exit conveyors: inline, 90º, 180º, ... • Additional 1 meter sealing device. • Automatic image centring device for printed films. • Printed band attachment. • Transparent tray detection. • Sealer Cooler. • Others (Ask). A high-performance wrapping machine, specially developed for the wrapping of trays in central processing facilities (meat, poultry, fish, vegetables, fruits) and high volume supermarkets. A large range of models for customer requirements. Its strength, reliability, ease of operation, and automatic size change, make it the most automatic size change, make it the most productive and versatile machine available, possibility to wrap with several kinds of film: PVC, polyethene and polyolefines. TECHNICAL FEATURES (Depend on the model) • 1 or 2 film rolls with automatic roll selection. • Automatic recognition of the tray dimensions or manual. • Automatic or manual selection of film length and width. • Universal elevator. • Self-diagnostic capability. • Film tension control. • Forward and reserve jog capability. • 4-way film stretch with lateral pre-stretch. • Temperature control for the sealing belt. • Oversize package detector. • Mechanical torque limiter. • Guards and safety devices according to international standards. • Heavy duty construction with corrosion-resistant material. Power supply: 380 V, 12 kW Bizerba GV labeller, manufactured in 2002 Bizerba 18A scale with Bizerba AB display. Automatic labelling and weighing system for products packaged in the food area. Electric power: Voltage 220 V, Frequency 50 Hz Current 1.7 A. Dimensions of tape width 300 mm. External dimensions of the machine: (mm) 1860 long x 720 wide x 1300 high. Compressed air supply of the blower label: air pressure: 6 bar, air flow: min. 100 l / min, compressed air. without oil, filtered at 10 µm, Label dimensions: 100x100. The separation between labels: from 2 to 20 mm. Thermal print head - resolution of 8.0 points Weighing from 1gr to 6000gr. Maximum labelling capacity 60 packages/minute. Equipment prepared for PC connection, Bizerba software allows the realization and design of labels adapted to your needs. Ability to print all types of barcodes, customer logos, etc. The equipment was reviewed, rebuilt, and guaranteed with the following maintenance: change of conveyor belts, thermal print head, and engine belts. High-quality equipment and great performance in terms of speed and reliability. The label and the scale are mounted on an output conveyor belt. Weighs at least 40 g up to a maximum of 18 kg For the Romanian companies, there is the possibility of selling in instalments. Price upon request, FCA: Oradea/Romania We sell this line refurbished Irrtum, Anderungen und Zwischenverkauf vorbehalten / Subject to errors, changes and prior sale / Ne rezervăm dreptul la greșeli, modificări și vânzare We speak English. /Wir sprechen Deutsch./ Beszélünk magyarul. /Nous parlons français/Vorbim romana

Condition: new, Year of construction: 2025, You are looking for a real machine and not a toy, then you have come to the right place: Fiber laser laser engraver large format X1130 x Y665 x Z260mm Laser markers skyLaser Mark - 2D optional 3D fiber laser engraving / marking laser is the complete solution for your complex laser engraving applications (* Prices depending on the equipment, this is a brand new laser machine from our production) Our skyLaser Mark systems are used exactly where conventional CO2 laser technology has its limits. Using the fiber laser with a wavelength of 1064nm, even the most delicate structures can be realized in almost any material. In contrast to conventional milling processes, the laser works without contact, force-free and without tool wear. The advantages in your application are the geometric flexibility and high processing accuracy. This type of processing can be used regardless of the hardness of the workpiece to be processed. The flexibility of the system increases with the mobile work table that can be adapted to your needs. You can easily integrate the system into your production line or operate it as a stand-alone solution. Our skyLaser Marks provide very precise and permanent markings (laser engravings) and are suitable for the special laser application area metal and certain organic substances. The use of a variety of fonts, the application of barcodes, serial numbers, logos and images is effortlessly possible. Thanks to the excellent resolution, almost all requirements for marking tasks can be solved. Production of stamps, engravings, lettering and complex, fine structures, the software is extremely user-friendly. Even very complex and time-consuming marking tasks can be easily created on the supplied industrial PC. You can do the exact positioning in next to no time, thanks to the optional observation camera for process tracking and software-supported workpiece alignment. Since the system has hardly any wearing parts and, thanks to the IPG laser technology, is almost maintenance-free, it can be used especially for industrial applications as well as in continuous use. The skylaser marking laser / engraving laser at a glance: Processing area: from 110 x 110 or 120x120 or fiber laser laser engraver large format with integrated axes X1130 x Y665 x Z260mm Laser source: IPG (pulsed fiber laser, YTTERBIUM PULSED FIBER LASER) SCANLAB SCANcube galvanometer scanner Gedpfxjf U Spxe Aivskc Nominal laser power: 20W New: software-controlled, variably adjustable working height (Z, axis max. 260mm depending on the structure) Optionally other work areas - automatic material feed, etc. Air cooling because of low energy consumption! Marking speed: up to 5000 mm / s (SCANLAB dyn AXIS ® galvanometer scanners the SCANcube ® achieve marking speeds of up to 640 characters per second.) Redundant security system Laser class: 1 or, depending on the configuration, laser class: 2 (with optional pilot laser) Pfeifer-technology HQ mirrors and optics for perfect results, powerd by Scanlab (R) pfeifer-technology industrial PC including pre-installed control software New: incl. Laser Focus Finder New: including process air control New: including extraction control Optional: Positioning laser: integrated diode laser for optimal positioning New including F-Theta lens 110 x 110 mm work area with protective glass! Fiber laser laser engraver large format X1130 x Y665 x Z260mm almost maintenance-free

Condition: new, Year of construction: 2026, PREMIUM VERSION MODELS ARE CHARACTERIZED BY HIGH RIGIDITY AND MAXIMUM RESOLUTION PRECISION, WORKING IN FULL INTERPOLATION IN EACH X, Y, Z AXIS. High-class CNC milling machine designed for the subtractive processing of materials, due to the whole range of configurations, it is used in many industries: industrial, electronics, welding, carpentry, advertising, etc. These are efficient and precise machines equipped with user-friendly CNC control systems. The price quoted is for the machine itself, excluding additional equipment, installation, transport and training. Design Welded steel rigid construction, The gate arms are made of hardened, thick, powder-coated sheet metal, which has increased stiffness, which translates into the quality of the processed detail. Work table The work table is made using hybrid technology, It has T-slots enabling manual clamping of material with dimensions of 2010 x 3010mm, Dissection table with four independent vacuum sections. Drive SERVO motors used to drive high-power machine tools provide appropriate acceleration and speed in individual directions, The X and Y axes are equipped with high-quality toothed bars, praised by users, which ensure high durability and precision, The Z axis is driven by a high quality ball screw. All axles move on rail guides. The machine is equipped with a tool height sensor, Linear bearings: trapezoidal rails, Hiwin carriages. Spindle Gedpjiz S Hasfx Aivekc The spindle design uses high-quality machine bearings, which are characterized by very quiet operation and guarantee increased durability. Tool height measurement sensor - included. The spindle speed range is from 4,500 to 18,000 rpm. Tool clamping using ER32 collets Software OPTIONALLY The latest UCanCAM V12 software in Polish language version (the software provides the ability to import files from Corel, Autocad, etc. File import/export, text editor and input and many other functions) The software enables quick and easy design of elements, which the program then converts to so-called G-code. It is also possible to import ready files from other programs. The machine is equipped with a function of remembering the last G-code path (In the event of a failure or power outage, it starts working from the last point without losing time or material.) DSP control Digital Signal Processing - digital signal processing. The machine's DSP controller has its own processor and RAM, which ensures failure-free operation and simple operation of the machine. The controller ensures smooth operation of the device and accuracy during processing. There is no need to reinitialize the program after a power loss. The memory built into the controller allows the machine to operate without having to load the program each time. We offer machine tools with real CE EU DTR - certified by the best in the EU. Technical parameters Spindle 5.5kW / 18000rpm inverter, air cooled Work area 2150x3200mm Maximum spindle height 350mm Control DSP Program resolution 0.001mm Software UCanCAM V12 in Polish language version(optional) Power supply 400V Libra 1450 kg Machine dimensions 2680x3600x2200mm Table height 715mm Vacuum pump 7.5 kW (optional) Underpressure 440 mbar Guides linear Drivetrain toothed rack (Z axis - ball screw) Axle drives hybrid servo drives

Condition: excellent (used), Year of construction: 2019, UV ink printer, year of manufacture and installation 2019 - production Japan According to the attached counter capture - 1,551 operating hours and 37,000 sqm printed. Perfect working condition - equipment is in production and can be viewed / tested Working table and material dimensions: Fixed table with dimensions of 125 X 250 cm and payload of 34 KG; Maximum material thickness - 5,08 cm; High power vacuum system - 6 vacuum zones; 5 pneumatic guides. Minimum per support with guides 60X80 cm; Printing heads: 2 piezoelectric heads 636 nozzles per channel and variable drop between 6 and 42 picolitres; Maximum print area covered by the heads is 126 X 251 cm for edge to edge printing; Nozzle detection and compensation system; Gsdpfxomcw S So Aivokc Automatic self-cleaning optional not mandatory. Number of colours : Digital Printer UV ink; 4 colours - CMYK (Cyan, Magenta, Yellow, Black) with the possibility to reactivate 6 colours white + transparent colourless lacquer. Resolution and Productivity : Maximum resolution 1440 dpi; Express speed - 58,7 mp/hour; Production speed - 35,7 mp/hour; Quality speed - 25,3 mp/hour; Quality speed 2 layers - 12,5 mp/hour; UV ink barrels - minimum 1 litre. Accuracy: Line thickness: Maximum error +/- 0.8 mm per 2.5 m side; Maximum error +/- 0.4 mm on 1.25 m side. Straightness: Maximum error +/- 0.7 mm on 2.5 m side; Maximum error +/- 0,5 mm on 1,25 m side. Diagonal error: Maximum error +/- 1,0 mm on 2,5 X 1,25 m. Other: Patented solution to achieve grey gradients; Stand/Working stand Ionizing bar (electrostatic discharge) Special bridge for loading and moving equipment. EXW - old price 49.000 euro - new price 35.000 (without VAT in EU)

Condition: new, Year of construction: 2026, functionality: fully functional, Ticab Printing System TPS is an innovative cantilever equipment. It allows feeding huge items beneath the print head. The print head can be adjusted up to 30 cm above the conveyor belt to feed folded cardboard boxes or other huge items. High quality Hewlett Packard HP pigment ink provides resistance to the fading, scratches and water after the image dries. Call us to get a beneficial commercial offer. Specifications:  Print area width: up to 29.7cm (11.7 in)  Print area length: from 2.54 cm (1 inch) to 91.44 cm (36 inch)  Workpiece movement speed: up to 45.72 cm (18 in) per second  Printing speed: up to 50--70 copies\min A4, up to 16 copies\min A3  Print resolution: 1200x1200dpi  Number of inkjet nozzles: 59136 (14 printing zones of 4224 nozzles each)  Colors: CMYK (Cyan, Magenta, Yellow, Black) Gsdpfxou Ibhws Aivekc  Ink type: water-based pigment ink  Information connection: Ethernet 10/100/1000 Base-T network port  Operating system: Windows (recommended Windows10)  Hewlett Packard HP driver  Trusted by professionals in 55 countries worldwide!

Year of construction: 2025, condition: new, X-ray inspection system for middle-sized bags, packs. Suitable for detecting foreign objects made of metal, glass, stone, plastic, etc. in food or non-food items. - Specifications: conveyor belt width: 410 mm; detection accuracy: Pb from Ø 0.2 mm, Fe from Ø 0.28 mm, SUS from Ø 0.28 mm, non-metallic such as stone, glass, from Ø 1.2 mm; X-ray output: 80 kVp, 1.25 mA; X-ray detector resolution: 0.4 mm; X-ray emissions: < 1usv/h; conveyor belt height: 850 ± 30 mm; conveyor speed (dependent on product dimensions): 10 – 100 m/min; screen: 15" touch screen; software: intellisens®X-ray; operating temperature: 5 – 35 °C; reject system: optionally available according to requirements; power: 220VAC, 50/60Hz; dimensions of the system L900xW920xH1825 mm; weight: 350 kg. Gksdpov Nm Inofx Aivjc Please note that our new prices are often below the usual used prices. Please feel free to inquire and tell us your packaging task. - Usually 30-50 different new machines are available immediately from stock. In addition, we have very short delivery times from approx. 3 weeks for customized machines. Deviations from the sample photo are possible. - All machines are available with full warranty.

Year of construction: 2025, condition: new, X-ray inspection system for middle-sized bags, packs. Suitable for detecting foreign objects made of metal, glass, stone, plastic, etc. in food or non-food items. - Specifications: conveyor belt width: 410 mm; detection accuracy: Pb from Ø 0.2 mm, Fe from Ø 0.28 mm, SUS from Ø 0.28 mm, non-metallic such as stone, glass, from Ø 1.2 mm; X-ray output: 80 kVp, 7 mA; X-ray detector resolution: 0.4 mm; X-ray emissions: < 1usv/h; conveyor belt height: 850 ± 30 mm; conveyor speed (dependent on product dimensions): 10 – 100 m/min; screen: 15" touch screen; software: intellisens®X-ray; operating temperature: 5 – 35 °C; reject system: optionally available according to requirements; power: 220VAC, 50/60Hz; dimensions of the system: L900xW920xH1825 mm; weight: 350 kg. Please note that our new prices are often below the usual used prices. Please feel free to inquire and tell us your packaging task. - Usually 30-50 different new machines are available immediately from stock. In addition, we have very short delivery times from approx. 3 weeks for customized machines. Deviations from the sample photo are possible. - All machines are available with full warranty. Gkedpjv Nm Iujfx Aivoc

Year of construction: 2025, condition: new, X-ray inspection system designed for large trays, boxes, large bags. Suitable for detecting foreign objects made of metal, glass, stone, plastic, etc. in food or non-food items. - Specifications: conveyor belt width: 600 mm; detection accuracy: Pb from Ø 0.2 mm, Fe from Ø 0.28 mm, SUS from Ø 0.28 mm, non-metallic such as stone, glass, from Ø 1.2 mm; X-ray output: 150 kVp, 7.5 mA; X-ray detector resolution: 0.4 mm; X-ray emissions: < 1usv/h; X-ray beam: horizontal scan; conveyor belt height: 750 ± 30 mm; conveyor speed (dependent on product dimensions): 10 – 60 m/min; screen: 15" touch screen; software: intellisens®X-ray; operating temperature: 5 – 35 °C; reject system: optionally available according to requirements; power: 220VAC, 50/60Hz; dimensions of the system: L1800xW1300xH1900 mm; weight: 580 kg. Godpfx Asv Nm Izjivskc Please note that our new prices are often below the usual used prices. Please feel free to inquire and tell us your packaging task. - Usually 30-50 different new machines are available immediately from stock. In addition, we have very short delivery times from approx. 3 weeks for customized machines. Deviations from the sample photo are possible. - All machines are available with full warranty.

Year of construction: 2025, condition: new, X-ray inspection system specially designed for glass bottles. Suitable for detecting foreign objects made of metal, glass, stone, plastic, etc. in food or non-food items. - Specifications: conveyor belt width: 85 mm; detection accuracy: Pb from Ø 0.2 mm, Fe from Ø 0.28 mm, SUS from Ø 0.28 mm, non-metallic such as stone, glass, from Ø 1.2 mm; X-ray output: 150 kVp, 7.5 mA; X-ray detector resolution: 0.4 mm; X-ray emissions: < 1usv/h; conveyor belt height: 1100 ± 30 mm; conveyor speed (dependent on product dimensions): 10 –100 m/min; screen: 15" touch screen; software: intellisens®X-ray; operating temperature: 5 – 35 °C; reject system: optionally available according to requirements; power: 220VAC, 50/60Hz; dimensions of the system: : L3500xW1300xH1795 mm; weight: 700 kg. Please note that our new prices are often below the usual used prices. Please feel free to inquire and tell us your packaging task. - Usually 30-50 different new machines are available immediately from stock. In addition, we have very short delivery times from approx. 3 weeks for customized machines. Deviations from the sample photo are possible. - All machines are available with full warranty. Godpfxsv Nm Nfo Aivokc