Used Moulding Machine for sale (83,448)

Condition: like new (used), functionality: fully functional, machine/vehicle number: SBO 6/10, Sidel Stretch Blow Moulding Machine Max. output: 6.000 bottles/hour. Max. bottle size: 3.000 cc. Blow stations: 6. Machine is in very good conditioning and well maintained. GENERAL INFORMATION The SBO 6/10 has 6 molds and 10 heating modules. Will work with a wide range of bottle sizes and styles from 0.25 to 3 liters. Sidel 2-step ^PET stretch-blow molders require previously manufactured preforms be supplied to the machine. Separating the bottle manufacturing and preform manufacturing processes allow production to be optimized, provide greater flexibility of operation and Hjdpfx Ageg Ailcs Usng use, and provide higher production output rates and yield. MAXIMUM PREFORM DIMENSIONS Neck height 9 – 41 mm (measured from bottom of support ring) Minimum inside diameter of neck 19 mm Maximum outside diameter of neck 34 mm Preform support ring diameter 29 – 51 mm Maximum preform length 210 mm MAXIMUM BOTTLE DIMENSIONS Maximum bottle diameter 130 mm Maximum bottle height 380 mm Bottle capacity 0.25 – 3 liters AVERAGE PREFORM WEIGHTS (non carbonated and carbonated liquids) 0.25 liter bottle 14-20 grams 0.50 liter bottle 20-33 grams 1.00 liter bottle 26-40 grams 1.50 liter bottle 35-51 grams 2.00 liter bottle 44-58 grams 3.00 liter bottle 68-84 grams BLOW WHEEL Height 3.5 meters Number of molds 6 Closing force 10 tons Item height (under neck) at outfeed 1.4 meters approximately Machine DC drive motor power 4 KW HEAT CONDITIONING Height 2 meters Number of oven heating units 10 Number of heating zones per unit 8 Maximum power 170 KW ELECTRICAL USAGE Maximum supplied power 200 KW Average consumption 100-150 KW/hr (varies per bottle being produced) COMPRESSED AIR Supplied power from 7-35 bar Pressure 7 bar Flow rate 50-100 Nm3/hr (varies per bottle being produced) Blow pressure – champagne base up to 25 bar Blow flow rate – champagne base 110-550 Nm3/hr Blow pressure – petaloid base up to 35 bar Blow flow rate – petaloid base 155-770 Nm3/hr CHILLED WATER Temperature 10-12 degrees Centigrade Pressure 5-6 bar Flow rate up to 6 cubic meters/hour Kcal to be removed up to 16,000 Kcal/hour WEIGHT Blow wheel with molds 8 tons Heat conditioning unit 2.2 tons Preform feeder 0.65 tons Electrical cabinet 0.85 tons PREFORM HEAT CONDITONING The preforms are transferred neck up to the heat conditioning device. This unit continuously insures the preforms are inverted before passing, neck down, in front of the heating units and then inverts them again. During the heating phase, the preforms are rotated and their necks protected from the heat in order to optimize the distribution of heat without deforming the neck. Heating is insured by 10 heat modules. Each unit can accommodate up to 8 infrared lamps stacked horizontally whose ends are air cooled. The heating power of 8 zones, corresponding to the 8 rows of lamps, can be controlled in order to optimize the heat profile. These zones are regulated on all SBO Models. After heating, a control by infra-red camera of preform temperature enables regulation of the zones under control, thus insuring maintenance of the required temperature.

Condition: good (used), Year of construction: 2000, operating hours: 69,000 h, functionality: fully functional, clamping force: 3,000 kN, screw diameter: 70 mm, For sale is an Engel injection moulding machine, type ERC 43/1-EA, including robotic handling. The machine is in good condition and ready for immediate operation. The machine is currently in operation and can be inspected on site. Professional dismantling and loading included. Technical data: Year of manufacture: 2000 Operating hours: 69,000 - Clamping unit: Clamping force: 3,000 kN Platen size: stationary 1,050x980 mm, moving 1,050x900 mm Min. mould installation height: 350 mm Max. platen distance: 1,200 mm 2 core pulls 2 air valves Centre ring diameter: 160 mm - Injection unit: Screw diameter: 70 mm Max. shot volume: 1,155 cm³ Specific injection pressure: 1,779 bar Temperature release up to 500°C - Handling: X: 500 mm Y: 800 mm Z: 1,880 mm C-axis: 0-90° pneumatic 2 suction/gripper circuits Freely programmable I/Os Conveyor belt 4,000 x 600 mm, height-adjustable Predefined program sequences, sprue separation, quality part placement Transport and loading can be organised Europe-wide at extra cost upon request. Prices are exclusive of VAT. Inspection is possible by appointment. Contact us—our team will be happy to assist you. Part exchange or trade-in possible! Hnsdsxc D Dcopfx Ag Ujg Machinery Purchase/Sale BUY / SELL PRODUCTION & METALWORKING MACHINES AND MUCH MORE. Do you need a high-quality yet affordable metalworking machine for your production? Or are you looking to sell your machine? For further information or to contact us, please visit our website.

Condition: ready for operation (used), Year of construction: 2018, operating hours: 28,076 h, General Data Machine weight 27000 kg Measurements height 2780 mm Clamping Unit Clamping force 4200 kN Injection Unit Screw diameter 60 mm Dimensions Machine Length 8900 mm Hodpox H U Enofx Ag Ujng This DEMAG El-Exis SP 420/820-2500 was manufactured in 2018. A robust electrical injection moulding machine, it features a screw diameter of 60 mm, a maximum dosing volume of 891 ccm, and a clamp force of 4200 KN. The tie bar distance is 820 mm. If you are looking to get high-quality moulding capabilities consider the DEMAG El-Exis SP 420/820-2500 machine we have for tact us for more information. Application Types Injection Moulding

Condition: ready for operation (used), Year of construction: 2005, operating hours: 60,000 h, functionality: fully functional, clamping force: 9,500 kN, screw diameter: 105 mm, clearance between the columns: 1,400 mm, displacement volume: 4,546 cm³, injection pressure: 1,778 bar, injection weight: 4,137 g, Clamping force 950 kN Mould opening force, max. 665 kN Travel force movable platen opening 112 kN Travel force movable platen closing 117 kN Size of mould platens (h x v) 1960 x 1710 mm Distance between tie bars (h x v) 1400 x 1150 mm Mould opening stroke 1800 mm Mould height min/max 600/1200 mm Max. daylight 2400 mm Injection unit: Hjdpfx Agsx Hz I No Uong Screw diameter 105 mm Ls/D ratio 23 Injection pressure 1778 bar Stroke volume 4546 ccm Shot weight (PS) 4137 gr. Injection rate 805 ccm/s Screw speed 126 1/min Plasticising rate max. 147 g/s Nozzle pressure 166 kN Electric and Hydraulic Equipment: Nominal capacity of pump motor 110 kW Installed heating capacity 59 kW Adjustable barrel heating zones 7 Reservoir capacity 1500 ltr. Dimensions and weights: Dimensions of the machine ca. 12,00 x 3,50 x 3,00 m Total machine weight 67000 kg Max. mould weight 20300 kg

Condition: ready for operation (used), Year of construction: 2019, operating hours: 19,884 h, General Data Machine weight 27000 kg Measurements height 278 mm Dimensions Machine Length 890 mm Injection Unit Screw diameter 60 mm Clamping Unit Clamping force 3500 kN This DEMAG El-Exis SP 350/820-2500 was manufactured in 2019. A robust electrical injection moulding machine, it features a screw diameter of 60 mm, a clamping force of 3500 KN, and a tie bar distance of 820 mm. With dimensions of 8.90 x 2.21 x 2.78 meters and a weight of 27,000 kg, consider the opportunity to buy this DEMAG El-Exis SP 350/820-2500 electrical injection moulding machine. Contact us for more information about this machine. Application Types Hedpfxjx H U Eho Ag Uong Injection Moulding

Condition: ready for operation (used), Year of construction: 2007, operating hours: 70,000 h, functionality: fully functional, clamping force: 6,500 kN, screw diameter: 95 mm, displacement volume: 3,367 cm³, Clamping force 6500 kN Mould opening force, max. 346 kN Travel force movable platen opening 169 kN Travel force movable platen closing 144 kN Size of mould platens (h x v) 1520 x 1470 mm Distance between tie bars (h x v) 1000 x 930 mm Mould opening stroke 1150 mm Mould height min 600 mm Max. daylight 1750 mm Hydraulic ejector - stroke 250 mm Ejector force 95 kN Injection unit: Screw diameter 96 mm Ls/D ratio 23 Injection pressure 1795 bar Stroke volume 3367 ccm Shot weight (PS) 3064 gr. Injection rate 690 ccm/s Screw speed 153 1/min Plasticising rate max. 104 g/s Nozzle pressure 166 kN Electric and Hydraulic Equipment: Nominal capacity of pump motor 90 kW Installed heating capacity 50 kW Adjustable barrel heating zones 7 Dimensions and weights: Dimensions of the machine ca. 9,83 x 2,90 x 2,80 m Total machine weight 43170 kg Accessories: - Anti vibration pads - Krauss Maffei Robot LR300 X: 1200 mm, servo Hjdpfx Asx Hzzcjg Uong Y: 1000/1000 mm, servo Z: 3500 mm, servo C: 0 - 90° - Conveyor - saftey guard Additional options: - 1 x air valve - 6 x pneumatic sequentional valves - 12 hotrunner controller - 2 x hydr. core pulls on movable plate - 2 x hydr. core pulls on fix plate

Condition: ready for operation (used), Year of construction: 2021, Main Drive Number of axis 3 Clamping Unit Clamping force 1300 / 1600 / 2000 kN Hnjdpfx Agjx D E Dyo Usg Additional Equipment Cooling water connection: Max. temperature: 30 °C, Min. Δp: 1.5 bar | DN 25 This 3-axis Arburg Allrounder 520S 1600-400 was manufactured in 2021. It features a screw diameter range of 35-45 mm and a clamping force up to 2000 kN. The machine includes a removal robot and an enclosure with a FilterFanUnit, ensuring clean operations. Ideal for precision plastic processing, it offers a mold clamping height of 250 mm and platen spacing of 825 mm. Contact us for more information about this machine. Application Types Injection Moulding

Condition: excellent (used), Year of construction: 2019, operating hours: 10,000 h, functionality: fully functional, clamping force: 13,000 kN, screw diameter: 90 mm, displacement volume: 2,990 cm³, Clamping force 13000 kN Distance between tie bars (h x v) 1380 x 1280 mm Mould opening stroke 2200 / 1500 mm Mould height min 650 / 1350 mm Max. daylight 2850 mm Hsdpfex Hygwjx Ag Ujng Hydraulic ejector - stroke 350 mm Ejector force 230 kN Injection unit: Screw diameter 90 mm Ls/D ratio 24.4 Injection pressure 2270 bar Stroke volume 2990 ccm Shot weight (PS) 2721 gr. Screw speed 133 1/min Plasticising rate max. 88,1 g/s Electric and Hydraulic Equipment: Nominal capacity of pump motor 94,5 kW Installed heating capacity 75,55 kW Reservoir capacity 1070 ltr. Dimensions and weights: Dimensions of the machine ca. 11,00 x 3,50 x 3,40 m Total machine weight 33000 kg Accessories: - Anti vibration pads Additional Options: - 2 x hydr. Core pulls on movable plate - 2 x hydr. core pulls on fix plate - 24 x hot runner controller - Robot interface according to Euromap 67

Condition: ready for operation (used), Year of construction: 2012, General Data Measurements width 1900 mm Measurements depth 6600 mm Measurements height 2400 mm Machine weight 14900 kg Injection Unit Screw diameter 50 mm Shot weight 482 g Stroke volume 530 cm3 Injection pressure 2426 bar Adjustable heating zones 5 Nozzle pressure 110 kN Clamping Unit Clamping force 2500 kN Opening stroke 670 mm Max open daylight 1380 mm Mould height min 330 mm Mould height max 710 mm Ejector stroke 200 mm Ejector force for / back 81 kN Media Pump drive power 30 kW Oil tank 550 L This SUMITOMO SHI DEMAG El-Exis S250/630-1600 was manufactured in 2012. It features a clamping force of 2500 kN, a screw diameter of 50 mm, and a shot weight maximum of 482 g. The machine has a dry cycle time of 1.2 seconds and a total installed power of 57.9 kW. If you are looking to get high-quality injection moulding capabilities, consider the SUMITOMO SHI DEMAG El-Exis S250/630-1600 machine we have for sale. Contact us for more information. Application Types Injection Moulding Hnodpfx Agjx D Nwqs Ueg

Condition: excellent (used), Year of construction: 2019, operating hours: 10,000 h, functionality: fully functional, clamping force: 13,000 kN, screw diameter: 90 mm, displacement volume: 2,990 cm³, Clamping force 13000 kN Distance between tie bars (h x v) 1380 x 1280 mm Mould opening stroke 2200 / 1500 mm Mould height min 650 / 1350 mm Max. daylight 2850 mm Hydraulic ejector - stroke 350 mm Ejector force 230 kN Injection unit: Screw diameter 90 mm Ls/D ratio 24.4 Injection pressure 2270 bar Stroke volume 2990 ccm Shot weight (PS) 2721 gr. Screw speed 133 1/min Hjdpfsx Hyf Tjx Ag Ujng Plasticising rate max. 88,1 g/s Electric and Hydraulic Equipment: Nominal capacity of pump motor 94,5 kW Installed heating capacity 75,55 kW Reservoir capacity 1070 ltr. Dimensions and weights: Dimensions of the machine ca. 11,00 x 3,50 x 3,40 m Total machine weight 33000 kg Accessories: - Anti vibration pads Additional Options: - 2 x hydr. Core pulls on movable plate - 2 x hydr. core pulls on fix plate - 24 x hot runner controller - Robot interface according to Euromap 67

Condition: ready for operation (used), Year of construction: 2004, operating hours: 64,300 h, General Data Measurements width 2200 mm Measurements depth 7200 mm Measurements height 2400 mm Machine weight 17700 kg Injection Unit Screw diameter 60 mm Shot weight 723 g/hp max Hedpfox D N Sbsx Ag Ujng Injection pressure 2500 bar max Clamping Unit Clamping force 3200 kN Opening stroke 700 mm max Distance between bars 720 mm x 720 mm Mould height min 300 mm Size of mold platens 1040 mm x 1040 mm Additional Equipment The Wittmann robot is not included Conveyor belt is included, protective housing only for the electrical components No other peripherals are included. This hydraulic injection moulding machine was manufactured in 2004. It features a screw diameter of 60mm and can handle a maximum injection weight of 723g. The machine supports a clamping force of 3200kn with a maximum opening stroke of 700mm. It is equipped with special features like 2xAS core pull and 6xDS hot runner control points. Ideal for robust performance in a production setting, the Arburg Allrounder Selecta 720 S 3200-2100 machine we have for sale. Contact us for more information. Application Types Injection Moulding

Condition: excellent (used), Year of construction: 2019, operating hours: 10,000 h, functionality: fully functional, clamping force: 13,000 kN, screw diameter: 90 mm, displacement volume: 2,990 cm³, Clamping force 13000 kN Distance between tie bars (h x v) 1380 x 1280 mm Mould opening stroke 2200 / 1500 mm Mould height min 650 / 1350 mm Max. daylight 2850 mm Hydraulic ejector - stroke 350 mm Ejector force 230 kN Injection unit: Screw diameter 90 mm Hjdjx Hydvspfx Ag Uong Ls/D ratio 24.4 Injection pressure 2270 bar Stroke volume 2990 ccm Shot weight (PS) 2721 gr. Screw speed 133 1/min Plasticising rate max. 88,1 g/s Electric and Hydraulic Equipment: Nominal capacity of pump motor 94,5 kW Installed heating capacity 75,55 kW Reservoir capacity 1070 ltr. Dimensions and weights: Dimensions of the machine ca. 11,00 x 3,50 x 3,40 m Total machine weight 33000 kg Accessories: - Anti vibration pads Additional Options: - 2 x hydr. Core pulls on movable plate - 2 x hydr. core pulls on fix plate - 24 x hot runner controller - Robot interface according to Euromap 67

Condition: ready for operation (used), Year of construction: 2014, operating hours: 22,626 h, Injection Unit Screw diameter 25 mm Clamping Unit Clamping force 100t This Arburg 470 H 1000-170 was manufactured in 2014. A hydraulic injection moulding machine featuring a closing force of 100t and a screw diameter of 25mm. Operating on 400V 3∼, 50Hz with a total connected load of 75kW. Ideal for precision moulding applications. Contact us for more information about this machine. Application Types Hnedpjx D Rcuefx Ag Ueg Injection Moulding

Condition: excellent (used), Year of construction: 2019, operating hours: 10,000 h, functionality: fully functional, clamping force: 7,500 kN, screw diameter: 80 mm, displacement volume: 2,262 cm³, Clamping force 7500 kN Distance between tie bars (h x v) 1110 x 960 mm Mould opening stroke 1400 / 900 mm Mould height min 450 / 1150 mm Max. daylight 2050 mm Hydraulic ejector - stroke 300 mm Ejector force 195 kN Injection unit: Screw diameter 80 mm Ls/D ratio 24.8 Injection pressure 2200 bar Stroke volume 2262 ccm Shot weight (PS) 2058 gr. Screw speed 145 1/min Plasticising rate max. 71 g/s Electric and Hydraulic Equipment: Nominal capacity of pump motor 83 kW Installed heating capacity 50 kW Reservoir capacity 950 ltr. Dimensions and weights: Dimensions of the machine ca. 9,24 x 3,00 x 3,10 m Total machine weight 33000 kg Accessories: - Anti vibration pads Additional Options: - 2 x hydr. Core pulls on movable plate - 2 x hydr. core pulls on fix plate - 24 x hot runner controller Hsdpfxjx Hx Sfj Ag Uong - Robot interface according to Euromap 67

Condition: ready for operation (used), Year of construction: 1999, operating hours: 12,396 h, Clamping Unit Clamping force 4200 kN Injection Unit Screw diameter 70 mm Hodpjx D Hyvjfx Ag Uong This DEMAG Ergotech 4200-2300 was manufactured in 1998. It is a hydraulic injection moulding machine featuring a clamping force of 4200 Kn and includes a Wittmann robot. Consider the opportunity to buy this DEMAG Ergotech 4200-2300 hydraulic injection moulding machine. Contact us for more information. Application Types Injection Moulding

Condition: used, Year of construction: 2007, operating hours: 68,000 h, functionality: fully functional, clamping force: 600 kN, screw diameter: 35 mm, displacement volume: 154 cm³, Clamping force 600 kN Mould opening stroke 335 mm Hydraulic ejector - stroke 105 mm Ejector force 19,1 kN Injection unit: Screw diameter 35 mm Injection pressure 1581 bar Stroke volume 154 ccm Shot weight (PS) 139 gr. Injection rate 151 ccm/s Screw speed 400 1/min Nozzle pressure 50,3 kN Electric and Hydraulic Equipment: Nominal capacity of pump motor 15 kW Dimensions and weights: Dimensions of the machine ca. 3,00 x 2,00 x 3,20 m Total machine weight 6800 kg Hjdpfx Aex Hxb Heg Ujng Accessories: - Anti vibration pads - Antivibration pads - 4-fold water flower

Condition: ready for operation (used), Year of construction: 2013, Injection Unit Injection pressure 1703 bar, 1297 bar, 1030 bar Screw speed 400 r/min, 320 r/min (current) Nozzle pressure 51.9 kN Screw diameter 25 mm Clamping Unit Opening stroke 458 mm Ejector stroke 100 mm Ejector force for / back 39.8 kN Clamping force 800 kN Hodpfx Agox D H Awe Ujng This Engel Insert 200V/60 rotary was manufactured in 2013. A vertical injection moulding machine, it represents a reliable option for precision moulding tasks. Consider the opportunity to buy this Engel Insert 200V/60 rotary vertical injection moulding machine. Contact us for more information. Application Types Injection Moulding

Condition: ready for operation (used), Year of construction: 2020, operating hours: 10,000 h, functionality: fully functional, clamping force: 9,000 kN, screw diameter: 100 mm, displacement volume: 3,691 cm³, Clamping force 9000 kN Distance between tie bars (h x v) 1180 x 1000 mm Mould opening stroke 1600 / 1000 mm Mould height min 500 / 1400 mm Max. daylight 2400 mm Hydraulic ejector - stroke 300 mm Ejector force 195 kN Injection unit: Screw diameter 100 mm Ls/D ratio 22 Injection pressure 1800 bar Stroke volume 3691 ccm Shot weight (PS) 3359 gr. Screw speed 135 1/min Plasticising rate max. 793 g/s Electric and Hydraulic Equipment: Nominal capacity of pump motor 85 kW Installed heating capacity 71 kW Reservoir capacity 780 ltr. Dimensions and weights: Dimensions of the machine ca. 9,24 x 3,21 x 2,88 m Total machine weight 38000 kg Accessories: - Anti vibration pads Hjdpfx Agoxcakrj Ujng - 4 x 8-fold water flower Additional Options: - 2 x Air valves - 2 x hydr. Core pulls on movable plate - 2 x hydr. core pulls on fix plate - 1 x pneum. Core pull on movable plate - 1 x pneum. Core pull on fix plate - Robot interface according to Euromap 67

Condition: ready for operation (used), Year of construction: 2015, operating hours: 15,642 h, General Data Measurements width 1810 mm Measurements depth 6950 mm Measurements height 2213 mm Machine weight 15750 kg Hedpfx Agjx D Hnte Usng Injection Unit Screw diameter 45 mm Clamping Unit Clamping force 350 ton Media Internal cooling Yes Additional Equipment Fanuc Robot This SUMITOMO SHI DEMAG Systec SP 350/720-840 was manufactured in 2015. It is a hydraulic injection moulding machine, ideal for precision plastic processing. Consider the opportunity to buy this SUMITOMO SHI DEMAG Systec SP 350/720-840 hydraulic injection moulding machine. Contact us for more information. Application Types Injection Moulding

Condition: ready for operation (used), Year of construction: 2013, operating hours: 27,551 h, General Data Measurements width 1260 mm Measurements depth 6460 mm Measurements height 2100 mm Clamping Unit Clamping force 2200 kN Additional Equipment Sepro Robot SDR 22 Hjdpfx Agex D Hnys Ueng This SUMITOMO SHI DEMAG IntElect 220/610-750 smart was manufactured in 2013. It's an electrical injection moulding machine known for its precision and efficiency. Ideal for those looking to enhance their production capabilities with reliable technology. Contact us for more information. Application Types Injection Moulding

Year of construction: 2007, condition: ready for operation (used), This Arburg 420A 1000-400 was manufactured in 2007. It features electromechanical main movements by servo drives, a modular plasticizing unit with adaptive temperature control, and a five-point double toggle clamping system with servo-electric adjustment. The Selogica control system enhances operational efficiency. If you are looking to get high-quality injection molding capabilities, consider the Arburg 420A 1000-400 machine we have for sale. Contact us for more information about this machine. Application Types Injection Moulding Hnodpsx D Hgvjfx Ag Ueg

Year of construction: 2012, condition: ready for operation (used), Injection Unit Screw diameter 55 mm Hjdpfex D I Egox Ag Ujng This Engel victory 750/160 Spex was manufactured in 2012. It is a hydraulic injection moulding machine featuring core pull, an ejector plate safety device, a 1/2" air valve, and a 10-way water distributor. Consider the opportunity to buy this Engel victory 750/160 Spex hydraulic injection moulding machine. Contact us for more information. Application Types Injection Moulding

Condition: ready for operation (used), Year of construction: 2014, operating hours: 18,612 h, Injection Unit Screw diameter 35 mm Clamping Unit Clamping force 150 t This Arburg 520 H 1500-400 was manufactured in 2014. It features a closing force of 150 tons and a screw diameter of 35mm, suitable for precision hydraulic injection moulding. Operating on 400V, it has a total connected load of 89 kW. Consider the opportunity to buy this Arburg 520 H 1500-400 hydraulic injection moulding machine. Contact us for more information. Application Types Hnsdpfxsx D Rc Uj Ag Usg Injection Moulding

Year of construction: 2019, operating hours: 17,716 h, condition: ready for operation (used), General Data Measurements width 1920 cm Measurements depth 7750 cm Machine weight 26210 kg Measurements height 2410 mm This SUMITOMO SHI DEMAG El-Exis SP 350/820-920 was manufactured in 2019. A robust electrical injection moulding machine with a screw diameter of 40 mm and a clamping force of 3,500 kN. It has operated for 17,716 hours with 12,440,761 cycles, ensuring extensive production capabilities. Consider the opportunity to buy this SUMITOMO SHI DEMAG El-Exis SP 350/820-920 electrical injection moulding machine. Contact us for more information. Application Types Injection Moulding Hnjdpfxsx D Nx Is Ag Usg

Condition: ready for operation (used), Year of construction: 2020, operating hours: 8,000 h, General Data Measurements width 1264 mm Measurements depth 4308 mm Measurements height 1779 mm Machine weight 4200 kg Injection Unit Screw diameter 25 mm Shot weight 46 g Heating capacity 5.7 kW Nozzle pressure 30 kN Clamping Unit Clamping force 500 kN Hnsdpfx Ajx D Eccog Uog Max open daylight 710 mm Distance between bars 370 x 370 mm Mould height min 200 mm Mould height max 410 mm Ejector stroke 90 mm Ejector force for / back 25 kN Additional Equipment Granule Dryer Handling System Conveyor Belt - 1400 mm x 400 mm Precision Scale Temperature Units - 2x HB‑Therm This SUMITOMO SHI DEMAG Intelect 2 50/370-110 was manufactured in 2020. It features a fully electric direct-drive system, NC5+ control for enhanced energy efficiency, and precise injection dynamics. Includes a granule dryer, industrial robot, conveyor belt, and temperature units. Ideal for high-quality injection moulding processes. Contact us for more information about this machine. Application Types Injection Moulding