Used Blow Moulding Machine for sale (65,139)

Condition: good (used), Year of construction: 2017, functionality: fully functional, LINEAR PET BLOWING MACHINE SET with auxiliary equipment AC ARCOR - multiBlow2 - 2017 Speed: 1,5L - 6000 Cavities: 4 Fodpequuvrsfx Aikepp Formats: 0,1 - 3,0L AUXILARY EQUIP 1. Chiller - M.T.A S.p.A - TAE EVO 051 2. LOW Pressure compressor - SHAMAL 45kw Unit price: 2000 eur / There are 3 units in total. 3. Dehumidifier Unit price: 300 eur / There are 3 units in total. 4. Receiver tank - Low pressure - MAX 16Bar 5. Receiver tank - High pressure - MAX 45Ba

Condition: like new (used), functionality: fully functional, machine/vehicle number: SBO 6/10, Sidel Stretch Blow Moulding Machine Max. output: 6.000 bottles/hour. Max. bottle size: 3.000 cc. Fsdpfx Aijg Ailcskepp Blow stations: 6. Machine is in very good conditioning and well maintained. GENERAL INFORMATION The SBO 6/10 has 6 molds and 10 heating modules. Will work with a wide range of bottle sizes and styles from 0.25 to 3 liters. Sidel 2-step ^PET stretch-blow molders require previously manufactured preforms be supplied to the machine. Separating the bottle manufacturing and preform manufacturing processes allow production to be optimized, provide greater flexibility of operation and use, and provide higher production output rates and yield. MAXIMUM PREFORM DIMENSIONS Neck height 9 – 41 mm (measured from bottom of support ring) Minimum inside diameter of neck 19 mm Maximum outside diameter of neck 34 mm Preform support ring diameter 29 – 51 mm Maximum preform length 210 mm MAXIMUM BOTTLE DIMENSIONS Maximum bottle diameter 130 mm Maximum bottle height 380 mm Bottle capacity 0.25 – 3 liters AVERAGE PREFORM WEIGHTS (non carbonated and carbonated liquids) 0.25 liter bottle 14-20 grams 0.50 liter bottle 20-33 grams 1.00 liter bottle 26-40 grams 1.50 liter bottle 35-51 grams 2.00 liter bottle 44-58 grams 3.00 liter bottle 68-84 grams BLOW WHEEL Height 3.5 meters Number of molds 6 Closing force 10 tons Item height (under neck) at outfeed 1.4 meters approximately Machine DC drive motor power 4 KW HEAT CONDITIONING Height 2 meters Number of oven heating units 10 Number of heating zones per unit 8 Maximum power 170 KW ELECTRICAL USAGE Maximum supplied power 200 KW Average consumption 100-150 KW/hr (varies per bottle being produced) COMPRESSED AIR Supplied power from 7-35 bar Pressure 7 bar Flow rate 50-100 Nm3/hr (varies per bottle being produced) Blow pressure – champagne base up to 25 bar Blow flow rate – champagne base 110-550 Nm3/hr Blow pressure – petaloid base up to 35 bar Blow flow rate – petaloid base 155-770 Nm3/hr CHILLED WATER Temperature 10-12 degrees Centigrade Pressure 5-6 bar Flow rate up to 6 cubic meters/hour Kcal to be removed up to 16,000 Kcal/hour WEIGHT Blow wheel with molds 8 tons Heat conditioning unit 2.2 tons Preform feeder 0.65 tons Electrical cabinet 0.85 tons PREFORM HEAT CONDITONING The preforms are transferred neck up to the heat conditioning device. This unit continuously insures the preforms are inverted before passing, neck down, in front of the heating units and then inverts them again. During the heating phase, the preforms are rotated and their necks protected from the heat in order to optimize the distribution of heat without deforming the neck. Heating is insured by 10 heat modules. Each unit can accommodate up to 8 infrared lamps stacked horizontally whose ends are air cooled. The heating power of 8 zones, corresponding to the 8 rows of lamps, can be controlled in order to optimize the heat profile. These zones are regulated on all SBO Models. After heating, a control by infra-red camera of preform temperature enables regulation of the zones under control, thus insuring maintenance of the required temperature.

Condition: used, Stretch blow molding machine by Etek ISBM line = Injection stretch blow molding Stretch blow molding machine for single-use PET bottles made from PET preforms Stretch blow molding machine for production using the rotary process Manufacturer: ETEK / GF-Industries, Type Supra 800 sv 1 Serial number: 22000225 Year of manufacture: 2012 Power: 90 kW Mains connection: 400 volts, 50 Hz Fpjdpfxjkucxle Aikep Weight: approximately 6000 kg In like-new condition

Condition: excellent (used), Year of construction: 2020, functionality: fully functional, ID BYP01 We sell a used Chinese - PP melt-blown fabric extrusion line for melt blown, make: Zhangjiagang Sevenstars Machinery Co., Ltd., MFG 2020. It was used for a short time. excellent condition. All EU import duties have been paid. Output max 400 kg per 24 hours. Fpjdpfx Aeuiq Dhoikjp General description: 1. Product size: PP melt blown fabric with width at 600mm (after trimming 17m*3) 2. Main Material: PP compounding material 3. Extruder type: SJ65/33 single screw extruder 4. Output capacity: 350-400kg/24hour 5. Electric power supply: 3phase, 380V; 50Hz 6. Additional equipment: • Vacuum feeder • Raw material dryer • Mesh manual filter • T-mould for melt blown fabric • Static electrical discharge equipment • Belt type forming 850mm • Collecting device • Winder and slitting Model L/D Output Speed of Screw Rotationl Power Center Height SJ-65 10-33 80-150kg/h 20-120r/min 18.5kw 1000mm This line contains the following machines: Automacic vacuum loader ZJ-400 and hopper dryer make RHONG model RDM-25, MFG 2020; Single screw extruder, model SJ65/33, MFG 2020; Heating oven for hot air, model HJGF101-4, MFG 2020; Extrusion T-mold, model: SUS630, made in Japan, MFG 2020; Forming device, MFG 2020; Winder & slitting system, MFG 2020; Oil free air compressor, MFG 2020; The PP melt blown nonwoven production line is a polymer melt extruded from a screw extruder. The polymer is extremely stretched by high-speed hot air or other means to form very fine short fibers, which are aggregated to A web is formed on a roller or a screen curtain, and is finally reinforced by self-adhesion or thermal bonding. Its unique properties are widely used in mask filter materials, thermal insulation filling materials, medical health materials, wiping materials, etc. The finished product can pass the N95 standard as the core material of the mask. Process of melt blown nonwoven production line Polymer preparation --- Melt extrusion --- Metering pump --- Melt blown die head assembly --- Solution thin-flow drawing --- Fibber cooling --- Auxiliary network --- Electrostatic electret --- Reinforced finished product. Melt-blown cloth is produced by melt-blown process. The equipment mainly includes: screw extruder, melt pump, screen changer, melt-blown device, winding device, air system (hot air blower and heater), etc. The function of the screw extruder is to melt the slice material; the role of the melt pump is to accurately measure, control the output and the fineness of the fiber, and continuously and evenly transfer the melt to the spinneret. The function of the screen changer is to filter out impurities in the melt so as not to block the spinneret holes. The function of the winding device is to pack the melt blown cloth into rolls. The function of the air system (hot air blower and heater) is to provide the temperature and pressure of the hot air used in the drawing of the spinning air stream. Price Euro 39.200 Euro + VAT, negotiable, FCA: Oradea / Romania Irrtum, Anderungen und Zwischenverkauf vorbehalten / Subject to errors, changes and prior sale / Ne rezervăm dreptul la greșeli, modificări și vânzare We speak English. /Wir sprechen Deutsch./ Beszélünk magyarul. /Nous parlons français/Vorbim romana

Condition: excellent (used), Year of construction: 2000, functionality: fully functional, machine/vehicle number: 13-13, The BLOMAX 4 Blowmoulding machine is of the model 13-13. The machine has no defects and operates in excellent condition with full functionality. Fpjdpfx Ajt Akgwjiksp Power : 400V/150A/60000W Year of construction : 2000

Condition: used, Year of construction: 1998, Automatic PET bottle blowing machine Manufacturer: SIDEL Type: SBO 16/16 S1 Year of manufacture 1998 Capacity: 16,000 for 1.5 L bottles and up to 19,000 bph for 0.5 L bottles Installed power: 347 kW Includes 1.5 L moulds Preform feeder Fsdpfxsutni Rs Aikjpp Chiller cooling unit Technical condition: used machine, functional until dismantled. The machine is currently dismantled, assembled in elements and prepared for transport. Full and original technical documentation.

Condition: like new (used), Year of construction: 2022, operating hours: 200 h, functionality: fully functional, screw diameter: 70 mm, overall weight: 600 kg, clamping force: 80 kN, total width: 2,800 mm, total length: 4,000 mm, total height: 2,260 mm, Main Features: 1. Computer Control System (PLC) – Japanese Mitsubishi PLC 2. Electrical Cabinet – All electrical components are sourced from globally renowned brands, ensuring quality and stability. 3. Touch Screen – Innovation computer control system 4. Advanced Hydraulic Cylinder from Germany 5. Linear Guideway 6. ABB Inverter from Switzerland & Rexroth from Germany 7. Large Diameter Galvanized Steel Pipes 8. Electric Lifting Platform 9. Ceramic Heater 10. Hydraulic System & Valve Connections – From Yuken Industry Technical Specifications: • Suitable Material: PE, PP, and others • Max Volume: 6 L • Production Capacity: 170-260 pcs/h • Dimensions: 4.0 × 2.26 × 2.8 m • Weight: 6T Plasticization System: • Reducer: Hard finishing, high strength, low noise • Screw: Ø 70 mm, L/D ratio 24, 38CrMoALA, cooling system available • Plasticization Capacity: 100 kg/h (HDPE) • Heating Zones: 3-4 aluminum heaters, automatic heating • Heating Power: 12 kW/h • Extruder Motor: Three-phase asynchronous motor (380V, 50HZ) • Cooling Fan: 4 zones, automatic cooling Extrusion System: • Material: High-grade alloy steel, central feeding • Number of Die Heads: 1 • Max Die Mouth Diameter: Ø 160 mm • Heating Zones: 4, stainless steel heating cycle • Heating Power: 5-7 kW Clamping System: • Features: High strength, rigidity, central mold locking, stable mold opening & closing • Clamping Force: 80KN • Template Distance Adjustment: 170-520 mm • Max Mold Size: 380 × 420 mm Electric System: • Automatic Monitoring, Fault Alarms, Auto Counting, Auxiliary Functions • Control Interface: Touchscreen with self-diagnosis alarm system • Temperature Control: Automatic temperature control module • Motion Control: Inovance (Chinese/English version) Hydraulic System: • Features: Multi-functional integrated hydraulic block, proportional control, high efficiency • Oil Pump Motor: Three-phase asynchronous motor (380V/220V, 50/60HZ) • Oil Pump: Imported double pump Fedjv Iflpjpfx Aikspp • Valves: Imported oil pump valves and connections • Oil Pipes: Double-layer wear-resistant • System Pressure: 60 kg/cm² • Cooling System: Separate water cooling cycle, oil cooler Pneumatic System: • Brand: Taiwan AIRTAC pneumatic system • Air Pressure: 0.6 MPa • Air Displacement: 0.8 m³/min • Electromagnetic Valve: Taiwan AIRTAC Main Components: Electronic Parts: • PLC Control System: MITSUBISHI from Japan • Touch Screen: INOVANCE • Temperature Controller: HUICHUAN • Auxiliary Relay: OMRON • Contactor: Schneider from France • Electric Motor: Three-phase 380V • Power Source: TAIWAN MEANWELL • Transducer: ABB from SWITZERLAND Hydraulic Parts: • Oil Pump: TAIWAN HIGH-TECH • Valve: YUKEN • Oil Pump and Connection: YUKEN • Sealed Part: HALLITE Air Control System: • Cylinder: AIRTAC • Air Valve: AIRTAC This blow molding injection machine was purchased directly from a factory in China for a specific project that was never realized. The machine was used for only one month. Location: Siemianowice Slaskie, Poland We also have peripheral equipment available for sale, such as: • 5 HP AIR COOLING SYSTEM • Auto Loading • 150 kg Color Mixer • Scraps Crusher

Condition: good (used), Year of construction: 2011, operating hours: 59,000 h, functionality: fully functional, clamping force: 250 kN, screw diameter: 30 mm, clearance between the columns: 270 mm, injection pressure: 2,000 bar, total length: 3,180 mm, total width: 1,430 mm, total height: 1,850 mm, overall weight: 2,110 kg, warehouse no.: 503725 manufacturer: ARBURG type: Allrounder 270 S 250-170 controller: SELOGICA year of construction: 2011 operation hours: 59000 h technical data clamping unit clamping force: 250 kN distance between tie-bars h x v: 270 x 270 mm size of mould plates h x v: 380 x 380 mm min. mould height: 200 mm max. open daylight: 550 mm opening stroke: 350 mm ejector stroke: 100 mm ejector force: 20 kN centering diameter of moving platen: 110 mm centering diameter of fixed platen: 110 mm technical data injection unit screw diameter: 30 mm swept volume: 85 ccm injection pressure: 2000 bar Fpjdoz Eax Ejpfx Aikop screw length: 20 l/d screw torque: 250 N injection rate into the open: 96 g/s PS number of heating zones: 4 nozzle stroke: 300 mm measures & weight measures of machine l x w x h: 3.18m x 1.43m x 1.85m total weight: 2110KG equipment included incl. Spruepicker screen text german screen text german core pulling hydraulically 1x Anti vibration mounts

Condition: excellent (used), Year of construction: 2021, functionality: fully functional, clamping force: 1,200 kN, screw diameter: 30 mm, overall weight: 10,000 kg, warehouse no.: 503724 manufacturer: Wittmann Battenfeld type: Vpower 120-350 R1300 controller: Unilog B8 year of construction: 2021 clamping force: 1200 kN distance between tie-bars h x v: 1160 x mm size of mould plates h x v: 740 x 580 mm min. mould height: 250 mm max. open daylight: 600 mm opening stroke: 350 mm round table diameter: 1300 mm screw diameter: 30 mm swept volume: 106 ccm injection pressure: 2835 bar An additional plasticizing unit is also available for changing with the following technical specifications: Screw diameter: 18 mm Stroke volume: 22.9 ccm Specific injection pressure: 3000 bar measures of machine l x w x h: 4.4m x 2.09m x 3.8m total weight: 10000KG equipment included screen text german Fodpfx Aie Aiq Enekjpp core pulling pneum. 2 x injection unit extremely wear resistant and corrosion resistant interface EUROMAP 63 interface OPC

Condition: excellent (used), Year of construction: 2014, operating hours: 54,738 h, functionality: fully functional, machine/vehicle number: 369A61525, screw diameter: 54 mm, overall weight: 9,000 kg, clamping force: 687 kN, total width: 1,850 mm, total length: 5,500 mm, total height: 3,200 mm, Equipment: documentation/manual, For sale: ASB Nissei 70-DPH, version 4 ISBM machine. Fpsdpfxo Ah H Dtj Aikop Included with the machine is a Piován desiccant air dryer. The machine is powered on and can be inspected while running in a dry cycle.

Condition: good (used), Year of construction: 1998, operating hours: 89,340 h, functionality: fully functional, screw diameter: 90 mm, overall weight: 16,000 kg, clamping force: 650 kN, total width: 2,750 mm, total length: 5,600 mm, total height: 3,200 mm, Manufacturer: Sterling Model: 15 LBS Year of manufacture: 1998 Operating hours: 89,340 h Closing force: 650 kN Screw diameter: 90 mm Fpedpfezfxwijx Aikep BM Sterling APV, year of manufacture 1998 Complete control system replacement in 2008 with MACO-sys 6000, carried out by Davies-Standard LTD PRICE REDUCTION OF 30%!!! Net price: from 45,000 EUR to 31,500 EUR!!!

Condition: ready for operation (used), Year of construction: 1970, operating hours: 1,362 h, functionality: fully functional, machine/vehicle number: 9286, planing width: 600 mm, Planer machine Kupfermühle Fpsdpsyyvuwofx Aiksp 5 spindles: bottom / top / right and left / bottom We have produced castle floorboards with this machine, and it was operational until the end. The machine can be demonstrated. Due to its age, it is sold without warranty or guarantee.

Condition: used, Year of construction: 2006, Semi-automatic PET bottle machine – ZENTRONIK ZR-7 1. Heating oven for PET preform heating Fpjdpfswnzdajx Aikjp 2. Semi-automatic PET bottle production machine Mould: double-cavity for 5.0L bottles (48 mm cap) Output: approx. 800 bottles/hour Technical condition: used, operational

Condition: ready for operation (used), Year of construction: 2007, operating hours: 65,000 h, functionality: fully functional, clamping force: 1,300 kN, screw diameter: 45 mm, injection weight: 289 g, Clamping force 1300 kN Mould opening force, max. 70 kN Size of mould platens (h x v) 745 x 770 mm Distance between tie bars (h x v) 470 x 470 mm Mould opening stroke 600 mm Mould height min 300 mm Max. daylight 900 mm Hydraulic ejector - stroke 150 mm Ejector force 23/10 kN Injection unit: Screw diameter 45 mm Ls/D ratio 22,4 Injection pressure 2336 bar Stroke volume 318 ccm Shot weight (PS) 289 gr. Injection rate 143 ccm/s Screw speed 265 1/min Plasticising rate max. 29,3 g/s Nozzle pressure 50 kN Fpjdpfx Aezyrudoiksp Electric and Hydraulic Equipment: Nominal capacity of pump motor 22 kW Installed heating capacity 15,5 kW Adjustable barrel heating zones 5 Oil Reservoir capacity 400 ltr. Dimensions and weights: Dimensions of the machine ca. 5,00 x 2,00 x 2,20 m Total machine weight 8000 kg Max. mould weight 1490 kg Accessories: - Anti vibration pads - 2 x 6-fold water regulator Additional Options: - 2 x Air valves - 1 x hydr. Core pull - 12 x hotrunner controller - Robot interface according to Euromap 67 - Accumulator - 1 x pneum. core pull

Condition: ready for operation (used), Year of construction: 2010, operating hours: 55,000 h, functionality: fully functional, clamping force: 5,000 kN, screw diameter: 90 mm, Clamping force 5000 kN Mould opening force, max. 279 kN Travel force movable platen opening 137,1 kN Travel force movable platen closing 116,8 kN Size of mould platens (h x v) 1370 x 1200 mm Fpsdpfx Aisz I Dvyskep Distance between tie bars (h x v) 1000 x 800 mm Mould opening stroke 1170 mm Mould height min 480 mm Max. daylight 1650 mm Hydraulic ejector - stroke 250 mm Ejector force 95 kN Injection unit: Screw diameter 90 mm Ls/D ratio 20 Injection pressure 1839 bar Stroke volume 2290 ccm Shot weight (PS) 2084 gr. Injection rate 604 ccm/s Screw speed 195 1/min Plasticising rate max. 134,2 g/s Nozzle pressure 129,4 kN Electric and Hydraulic Equipment: Nominal capacity of pump motor 90 kW Installed heating capacity 44 kW Adjustable barrel heating zones 7 Reservoir capacity 1175 ltr. Dimensions and weights: Dimensions of the machine ca. 8,00 x 2,52 x 2,40 m Total machine weight 28800 kg Max. mould weight 7900 kg Accessories: - Anti vibration pads Additional Options: - 1 x air valve - 2 x core pull on fix plate - 2 x core pulls on movable plate - 8 x hotrunner controller - Robot interface according to Euromap 67

Condition: good (used), Year of construction: 1994, functionality: fully functional, Manufacturer: s.p.a magic m.p. Type: MGL2D This blow molding machine is in full working order. It is still in production and can be inspected after scheduling an appointment. Upon request, I can also send videos. Fjdpjxxp Tbjfx Aikjpp PRICE REDUCTION OF 30%! PRICE: REDUCED FROM 19,000 TO 13,300 EUR!

Condition: good (used), Year of construction: 2003, functionality: fully functional, planing width: 230 mm, working height: 100 mm, Planer Moulder P 1000 UNIMAT STAR with 6 Tool Holders Fpodoxyu Itspfx Aiksp

Condition: new, Year of construction: 2005, Planing machine with infeed device EM 11 Fjdpfx Aozvvuaoikopp with 5th spindle at the bottom Includes 5 planing heads.

Condition: ready for operation (used), Year of construction: 2002, functionality: fully functional, machine/vehicle number: 271/1, overall weight: 700 kg, Semi-automatic PET bottle blowing machine for producing 5-gallon PET bottles. Fpjdpfx Aiezd Tduokep Includes heating and blowing unit. Supplied with 2 sets of 5-gallon blowing molds. Capacity: 60 bottles/hour.

Condition: used, Year of construction: 1992, Automatic PET bottle blowing machine Manufacturer: SIDEL Type: SBO 4 S1 Year of prod. 1992 Capacity: 4,000 for 1.5 L / 2 L bottles Installed power: 150 kW Includes 1.5 L molds Preform feeder Fpedpowa Rhrefx Aikep Technical condition: used machine, starts up, program is functional

Condition: ready for operation (used), Year of construction: 2010, operating hours: 43,000 h, functionality: fully functional, clamping force: 6,500 kN, screw diameter: 80 mm, Clamping force 6500 kN Mould opening force, max. 346 kN Travel force movable platen opening 169 kN Travel force movable platen closing 144 kN Size of mould platens (h x v) 1510 x 1370 mm Distance between tie bars (h x v) 1000 x 930 mm Mould opening stroke 1150 mm Mould height min 600 mm Max. daylight 1750 mm Hydraulic ejector - stroke 250 mm Ejector force 95 / 48 kN Injection unit: Screw diameter 80 mm Ls/D ratio 22,5 Injection pressure 2205 bar Stroke volume 1810 ccm Shot weight (PS) 1647 gr. Injection rate 498 ccm/s Screw speed 195 1/min Plasticising rate max. 106 g/s Nozzle pressure 129 kN Electric and Hydraulic Equipment: Nominal capacity of pump motor 90 kW Installed heating capacity 44 kW Adjustable barrel heating zones 7 Dimensions and weights: Dimensions of the machine ca. 8,50 x 3,00 x 2,70 m Total machine weight 35000 kg Accessories: - Anti vibration pads - 10-fold water regulator - Krauss Maffei Robot LRX250 X: 900 mm Servo Y: 1000/1000 mm Servo Z: 3500 mm Servo C: 0 - 90 ° Fpjdpfx Asz N E Eyoikjp Additional Options: - 2 x core pulls on movable plate - 2 x core pulls on fix plate - Robot interface according to Euromap 67 - 6 x hydraulic sequentional valves - 12 x hotrunner controller - 1 x Air valve

Condition: excellent (used), Year of construction: 2017, functionality: fully functional, Equipment: documentation/manual, For sale: Complete PET bottle blowing line TES BluLine4 HiTech MultiFlex (2017) We offer for sale a complete PET bottle production line from the renowned manufacturer TES Sp. z o.o., model BluLine4 HiTech MultiFlex, manufactured in 2017. The machine is in very good technical condition, regularly used, and ready for further operation. Technical data Manufacturer: TES Sp. z o.o. Model: BluLine4 HiTech MultiFlex Year of manufacture: 2017 Bottle capacity range: 0.5 l – 4 l Number of cavities: 2-4 The line includes: ✅ Preform feeder Fpsdozd Sb Sepfx Aikep ✅ PET bottle blowing machine ✅ Bottle packer for trays Advantages of the equipment Complete and ready-to-use production line Universal range of produced capacities Solid construction and proven TES technology Very good technical condition Ideal for manufacturers of beverages, water, household chemicals, and other products packaged in PET bottles Price: negotiable. If you have any questions or would like to obtain additional information, please contact us by phone or private message. We will gladly provide detailed information and send additional photos of the equipment.

Condition: used, Year of construction: 2016, machine/vehicle number: SO125, Used Blow Molding Machine Terekas up to 5L 1000 bph This used blow molding machine from Terekas, model FlexBlow 1, is designed for demanding PET bottle production, offering advanced flexibility and efficiency. With a maximum bottle capacity of up to 5 liters and a throughput of up to 1,000 bottles per hour, the system is engineered for operations that require consistent product quality across multiple neck finishes and formats. The FlexBlow 1 utilizes a linear blow molding architecture, equipped with a single cavity, making it ideal for short production runs, frequent changeovers, or pilot lines. It integrates seamlessly into existing filling and packaging lines, thanks to its modular design and compatibility with multiple container types. The preform feed system includes a tipper, unscrambler, and loader, all designed to ensure reliable, jam-free supply of preforms into the production cycle. The core of the process begins with a robust preform heating tunnel, employing infrared (IR) lamps enclosed within a secure, ventilated housing. Preforms are conveyed through the heating zone by an articulated chain system, which ensures precise and uniform exposure to the heat source. The IR heating zone is shielded by a protective grid, preventing accidental contact while maintaining optimal thermal consistency across the preforms. The tunnel design avoids excessive hot spots or thermal degradation of the preform, contributing to higher end-product quality and reduced scrap rates. Fpedpfx Ao Adyymeikop Precise Control and Reliable Operation After exiting the heating tunnel, preforms are transferred automatically into the blow molding station. The FlexBlow 1’s single-cavity blow unit utilizes high-efficiency pneumatic actuators and robust mold clamping mechanisms to produce containers up to 5 liters in volume. This configuration allows for rapid cycling and excellent pressure control throughout the stretch-blow sequence. The complete air handling system is engineered for reliability, with integrated air recovery to optimize compressed air consumption and reduce overall utility costs. Critical to the system’s operation is the dedicated chiller, which ensures mold cooling circuits remain within the required temperature range, guaranteeing consistent bottle wall thickness and minimizing cycle times. All pneumatic and hydraulic components are mounted in a well-organized auxiliary area, with clearly labeled connections for maintenance and diagnostics. Filtration and lubrication points are readily accessible, supporting a high level of system uptime and minimizing unscheduled stops. Machine operation and process parameters are managed through a touchscreen HMI panel installed directly on the electrical cabinet. This interface provides real-time control over all production settings, alarm management, and maintenance prompts. The entire machine is wired in a highly organized manner, with secured electrical panels, neatly routed cables, and clearly identified terminals for ease of troubleshooting. All safety guards and interlocks are present and functional, ensuring the operator’s safety while maintaining access...

Condition: used, Year of construction: 1999, - PET-Blow moulding machine, make Sidel, type: SBO 16 with preform tipper, preform feed, unscrambler, preform transport, built 1999, already dismantled, ex location for sale. Fodpfx Asrazwrjikspp - PET-Blow moulding machine, make Sidel, type: SBO 20, with preform tipper, preform feed, unscrambler, preform transport, built 1999, already dismantled, ex location for sale.

Condition: used, Year of construction: 2020, functionality: fully functional, clamping force: 2,500 kN, total width: 12,500 mm, total length: 11,500 mm, total height: 8,600 mm, power: 831 kW (1,129.84 HP), Equipment: documentation/manual, For sale is a highly automated BBM 2500 CoEx3 extrusion blow molding machine, manufactured in 2019. The machine is in very good technical condition, fully functional, and immediately available. An inspection while the machine is running can be arranged by appointment. The machine is designed for the economical production of large-volume HDPE hollow bodies and sophisticated technical blow-molded parts. It is a batch-type 3-layer extrusion blow molding machine with a parison accumulator head. The offered scope of supply includes: - Piovan GMS-160 high-performance plastic granulator, manufactured in 2023 - Piovan VM 500 extraction system - GWK/Technotrans cooling unit The listed peripheral components are included in the offer price. If individual components or the entire range of accessories are not required, they can be removed from the scope of supply, and this will be taken into account when determining the price. Technical key data: Manufacturer/Model: BBM 2500 Year of manufacture: 2019 Process: CoEx3 extrusion blow molding with parison accumulator head Material: HDPE Design: 1 station with 1 CoEx3 blow head 3 extruders: 1 × 130 mm and 2 × 70 mm Total output: up to 1,200 kg/h Accumulator volume: 1 × 20 l and 2 × 7.5 l Fpsdpfozw D Haox Aikjp Electrical wall thickness control Clamping force: 2,500 kN Platen area: 2,160 × 2,400 mm Column spacing: 1,500 × 2,400 mm Opening width: 600–1,500 mm Electrical closing movement Locking via 6 hydraulic power strokes 2 integrated KUKA 6-axis robots for removal and handling Fully automatic KOCH material feeding system with gravimetric dosing and mixing Beckhoff TwinCAT control with Siemens components and drives Connected power: 831 kW Power supply: 400 V, 3 phases/N/PE, 50 Hz Dimensions: approx. 11,500 × 12,500 × 8,600 mm (L × W × H) CE documentation and machine manuals available The machine is particularly suitable for large-volume hollow bodies, technical molded parts, infrastructure products, sanitary parts and industrial containers. Availability: immediate Inspection and trial run: possible by prior appointment