Baler incl. conveyor VK 8818 R-FU
HSM GmbH + Co. KG, Germany HSM VK 8818 F-RU

Name: HSM GmbH + Co. KG, Germany HSM VK 8818 F-RU
Brand: HSM GmbH + Co. KG, Germany
Availability: InStock

Year of construction

2012

Condition

Used

Location

France

Baler incl. conveyor VK 8818 R-FU HSM GmbH + Co. KG, Germany HSM VK 8818 F-RU

HSM GmbH + Co. KG, Germany HSM VK 8818 F-RU

Show map

Machine data

Machine type:: Baler incl. conveyor VK 8818 R-FU

Manufacturer:: HSM GmbH + Co. KG, Germany

Model:: HSM VK 8818 F-RU

Year of construction:: 2012

Condition:: good (used)

Functionality:: fully functional

Operating hours:: 12,078 h

Price & Location

Location:: , France

Call

Technical details

Pressing force:: 88 t

Filling opening width:: 1,100 mm

Filling opening length:: 1,800 mm

Bale width:: 1,100 mm

Bale height:: 750 mm

Bale weight:: 750 kg

Overall weight:: 30,000 kg

Oil tank capacity:: 2,000 l

Power:: 98 kW (133.24 HP)

Volume flow:: 643 m³/h

Details about the offer

Listing ID:: A19999915

Update:: 15.09.2025

Description

Technical data baler:
Manufacturer HSM GmbH + Co. KG, Germany
Type VK 8818 R-FU
Year of construction 2012
Total operating hours: 12,078 hours, as of September 2025
Pump operating hours 6,616 hours (effective pump running time)
Number of bales pressed: 65,792 bales, as of September 2025
Main press force 880 kN
Specific pressing force 120 N/cm²
Pressing force cutting edges free rammer 120 kN
Dimensions of feed chute 970 x 1,800 mm
Kodpfsxcngnsx Aa Ejfa
Theoretical cycle time in idle mode 8.3 seconds
Theoretical throughput capacity 643 m³/hour
Bale dimensions 1,100 x 750 mm, the length is variable 600 up to 2000 mm
Drive power 2 x 45 kW frequency-controlled
Connected load 98 kW
Total current consumption 192 A
Fuse protection 250 A slow-blow
5-fold horizontal tying, fully automatic
Throughput rates with a
bulk density of 20 kg/cbm 12.86 t/hour
Bulk weight of 50 kg/cbm 32.15 t/hour
Bale weights with a bale length of approx. 1.2 m 650 up to 750 kg/bale, depends on materiel
Hydraulic oil tank capacity 2000 litres
PLC control Siemens S7-300
Siemens TP 700 control panel
Press dimensions assembled 18,000 x 4,300 x 3.270 mm (l x w x h)
Press dimensions with conveyor system 18,000 x 22,000 x 5,765 mm (l x w x h)
Transport weight baler approx 30 t (Main press approx. 20 t, press channel with bale clamp approx. 10 t)

Special machine equipment:
Access locking by means of key transfer system
Electro-hydraulic locking of the press carriage during the tying process so that the press plunger does not change position with highly expansive materials

Additional optional equipment ordered:
Frequency-controlled main drive, 2 x 45 kW, with up to 40 % energy savings compared to the standard motorisation 2 x 45 kW, with the same power output
Manual switch-off or switch-on of the number of strapping wires to save on strapping wire for non-expansive material
Cutting-edge frei rammer with 121 kN pressing force
Sensory wire monitoring, with press switch-off in the event of wire breakage or wire end
Bale chute
Visual warning signal, mounted on the control cabinet

Condition of the baler:
The entire baling system (baler and conveyor belt) is in good, operational condition.

Technical data for the chain belt conveyor:
Manufacturer Stadler Anlagenbau GmbH
Typ chain belt conveyor KF 1800
Year of construction 2012
Drive power 7.5 kW
Belt speed 0.05 – 0.4 m/second
Length of feeding conveyor 6,000 mm
Height of side wall from feeding conveyor 400 mm
Length of incline conveyor 9,000 mm
Height of side wall from incline conveyor 800 mm
Length of gooseneck 1,500 mm
Incline 30°
Nominal width 1,800 mm
Useful width 1,700 mm
Belt quality EP-500/4
Steel cleats on the rubber belt 50 x 50 mm
Hollow pin chain, pitch 125 mm, rollers 36 mm
Height of drive axle above ground 4,284 mm
Overall height of conveyor belt 5,765 mm
Transport dimensions of feeding conveyor approx. 7,000 x 2,200 x 1,250 mm (l x w x h)
Transport dimensions of the incline conveyor 13,000 x 2,500 x 2,900 mm (l x w x h)
Pit dimensions for the conveyor belt 14,765 x 3,260 x 1,250 (l x w x h)

Scope of delivery:
The conveyor belt, baling press with bale chute, and wire drawing stations are available for sale, but without the wire.

Comments:
The documentation (Manual, CE-declaration, electr./hydr.-drawings), are completely available. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors.

Documents

19999915-01.pdf

Seller

Registered since: 2017

30 listings online

Call

Send inquiry

Telephone & Fax

+31 597 2... show

These listings may also fit your interest.

Listing

All terrain crane Effer 955/8S Volvo 540 Euro 6, Valid Inspection, 8x2x4 D

Groenlo

1,011 km

All terrain crane
Effer955/8S Volvo 540 Euro 6, Valid Inspection, 8x2x4 D

Call

Condition: used, mileage: 129,252 km, lifting height: 38,000 mm, Year of construction: 2015, Drivetrain Drive: Wheel Weights Empty weight: 27.875 kg Functional Lifting capacity: 23.800 kg Identification Serial number: 122024 Other information Front tyres / undercarriage remaining: 70 Rear tyres remaining : 70 Tyre brand: Bridgestone Carrier engine: - Upper engine: - Counterweight: 0 Transport dimensions (LxWxH): 11.1x2.55x3.9 Additional information Kodpfxsw A Hcds Aa Ejfa Please contact PFEIFER GROUP for more information

See details

Listing

Baler with 8-fold cross tying system Presona AB LP 80 VHK 1

Netherlands

1,011 km

Baler with 8-fold cross tying system
Presona ABLP 80 VHK 1

Call

Condition: reconditioned (used), Year of construction: 2012, operating hours: 25,895 h, functionality: fully functional, pressing force: 78 t, filling opening width: 1,100 mm, filling opening length: 1,500 mm, bale width: 1,100 mm, bale height: 750 mm, bale weight: 600 kg, overall weight: 24,000 kg, oil tank capacity: 1,000 l, power: 55 kW (74.78 HP), volume flow: 930 m³/h, Technical data baler: Manufacturer Presona AB Typ LP 80 VHK 1 Year of construction 2012 Total machine operating hours 25,895 hours, as of July 2025 Pump operating hours, effective 14,135 hours, as of July 2025 Number of bales pressed 235,597 pieces, as of July 2025 Press power main press 78,5 tons Specific press capacity 95 N/cm² Press power of pre-press 28 tons Volume of pressing chamber 2,7 m³ Feed channel1,500 x 1,100 mm Theoretic throughput rate 930 m³/h Throughput rate under operating conditions 410 m³/h Bale size 750 x 1,100 mm Driving motor 55 kW Tying system 5 fold vertical, 3-fold horizontal, full automatic Throughput rate with a bulk density of 30 kg/m³ approx. 9 to 12 tonnes/hour, depending on material 50 kg/m³ approx. 14 to 17 tonnes/hour, depending on material 100 kg/m³ approx. 16 to 25 tonnes/hour, depending on material Throughput capacity with MSW (Municipal Solid Waste) approx. 20 to 27 tonnes/hour, depending on material Bale weight 450 up to 600 kg, depends on material and bale length Volume hydraulic oil tank 1,000 l Baler dimensions built up with hopper 10,985 x 3,750 x 4,310 mm (l x w x h) Transport dimensions only baler 10,985 x 2,300 x 2,900 mm (L x w x h) Machine weight baler approx. 24 tons Condition of the press: The machine was partially overhauled and serviced in our workshop and, once the work was complete, tested in manual and automatic mode during operation. Kedpfx Aaovwlqqj Eofa The following overhaul work was carried out: Machine cleaned, partially derusted and partially repainted Hydraulic oil tank emptied and cleaned Oil filter and air filter replaced, new hydraulic oil filled Press ram dismantled and cleaned All four rollers removed from the press ram and replaced Wire station with deflection rollers for the lower wire cleaned and made operational Side guides removed from the press ram, smoothed, mounted and readjusted Main hydraulic cylinder dismantled and disassembled for inspection Piston rod replaced, cylinder tube honed Complete seal set replaced, pressure test carried out Vertical and horizontal needle system for binding dismantled, cleaned, wire deflection rollers made functional and serviced Chain cleaned, greased, chain tension readjusted Drillomat cleaned, wire knife, drill shafts and drill fingers checked, retightened with torque and serviced Door contact switch checked and partially replaced. Emergency stop switch checked. Complete electrical wiring checked and partially replaced. Bearings of the wire guide rollers under the press replaced. New safety grilles for vertical and horizontal binding manufactured and installed. Machine checked, general maintenance work carried out and press tested in manual and automatic mode Scope of delivery: Only the baler will be sold. Comments: The documentation (Manual, CE-declaration, electr./hydr.-drawings), are completely available. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors.

See details

Listing

Wadgassen

1,141 km

Minolta C759 with finisher
Minoltac759

€2,000

fixed price plus VAT

Call

Listing

Bergatreute

1,408 km

Shredder, chipper ,
SIM2500 S

€30,000

ONO plus VAT

Call

Listing

Villers-la-Montagne

1,069 km

Shredder twin shafts
SATRINDF1015

€15,000

ONO plus VAT

Call

Condition: ready for operation (used), Year of construction: 2006, functionality: fully functional, power: 11.03 kW (15.00 HP), overall weight: 1,500 kg, input voltage: 380 V, ejection height: 1,000 mm, opening width: 600 mm, rotor length: 1,000 mm, rotary shear 2 shafts - 2 motors 15kw and 12kw - inversion in case of jam - shredding chamber 1100 x 900 - thickness of new knives 30 - 4 tons - large loading hopper - possibility of loading Kfjdpfx Ash Diwuja Esa very versatile and very powerful, can pre-grind organic matter for methanizers, copper cables, lumps, plaster, BA13, D3E, plastics, wood, bumpers, bottles, metals, hollow bodies, etc. use to grind up sick calves at the renderer.

See details

Listing

Paper cutting guillotine Ideal 4850-95 EP Paper cutting guillotine

Radom

1,994 km

Paper cutting guillotine
Ideal 4850-95 EPPaper cutting guillotine

Call

Condition: good (used), Paper cutting guillotine Ideal 4850-95 EP Machine in very good condition. Not used in production. Technical data: working width: 475mm stack height: 80mm minimum remnant: 35mm max distance of saddle from knife: 450mm 230V power supply Basic features: The machine has an EP programmer with the function of moving to a given dimension and saving individual steps to the device’s memory. After calling the program, the machine moves to the given and next step from memory. electromechanical knife, clamp and saddle drive automatic clamp synchronized with the knife cutting movement electronically controlled saddle adjustment knob with adjustable travel speed transparent covers on the front and rear tables Ksdpfxswt Srlo Aa Esfa two-handed cutting start, electronically controlled automatic knife return from any position optical cutting indicator Additional equipment: tapping block, cutting stick, knife replacement tools, documentation.

See details

Listing

Nederweert

978 km

Mobile excavator
ATLAS250MH

Call

Condition: ready for operation (used), functionality: fully functional, power: 114 kW (155.00 HP), gearing type: automatic, fuel type: diesel, color: orange, operation weight: 25 kg, tire condition: 50 %, axle configuration: 2 axles, number of seats: 1, Year of construction: 2015, operating hours: 8,454 h, machine/vehicle number: 250M301296, Equipment: UVV, additional headlights, air conditioning, cabin, crane, hydraulics, trailer coupling, 6.20 + 4.80 m incl. generator Sorting grab Polyp grab Lifting magnet all with quick coupler also available: Atlas 230MH | 2011 | 6.80 + 5.00 | Polyp grab Liebherr A904C | 2011 | 6.60 + 5.00 | Polyp grab Kodjtucngspfx Aa Eofa

See details

Listing

Nieuwkuijk

927 km

Eba 550
Eba550

€2,475

ONO plus VAT

Call

Condition: excellent (used), Very nice papercutting machine. Brand Eba type 550 made in Germany. Hydraulic clamp and hydraulic cut full programatic function. Line indicator table safety cover. Single phase complete with extra blade and blade changing tools. With all manuals. Of course you are welcome to test this machine with us. We can arrange the transport/packaging for you and load it into a truck or container. Ask for a price including transport (location the Netherlands). Regards Henk Hoos. Kfsdpfxou U Eh Ej Aa Eea

See details

Listing

Bollegraaf HBC140s (2x75kW) 2003 Bollegraaf HBC 140

Dordrecht

891 km

Bollegraaf HBC140s (2x75kW) 2003
BollegraafHBC 140

Call

Year of construction: 2003, operating hours: 43,000 h, condition: repair required (used), machine/vehicle number: HBC 140 2x75kW 2003 (W230-005), Sold by Bollegraaf Recycling Solutions, the original manufacturer of this Bollegraaf baler and conveyor: Bollegraaf HBC140s Baler (2x75kW). Baler: Weight: 47.100 kg Construction year: 2003 Hardox bottom floor plate only Plastic valve Anti-rat cabling Hours 43.000 This baler can also be sold fully refurbished according to the 'Bollegraaf OEM Certified Refurbishment standards'. This includes 2 year guarrantee. Contact us for more information or a quotation. General principles of refurbishment Cleaning & disassembly Before the actual refurbishment takes place the baler is completely cleaned and disassembled in our refurbishment workshop. Tolerances After the disassembly the tolerances of all steel components are measured and re-welded where necessary, this at least applies to the following components; • Ram, • Frame, • Channel, • Pre-press-flap After disassembly and inspection the ram is welded-up again and fitted with new ram wheels. The protective grids and the pre-press flap are made dent-free and repaired where necessary. Repainted After measuring the tolerances and any repair- and welding work, all components are being blasted and coated again. Hydraulics: The hydraulic tank is cleaned. The hydraulic lines & hoses are replaced. The hydraulic components are repackaged. The hydraulic oil is replaced. Cabling: All cabling is checked and replaced if necessary. All junction boxes are replaced and placed back in easily accessible positions. Wear parts: All wearing parts are replaced. The pins and shafts of the cylinders and the channel are replaced with new ones. All wearing parts of (both) needle installations and knotters are replaced for new. Cylinders: The cylinders are repackaged and, if necessary, provided with a new chrome layer or a new cylinder rod. MCC Cabinet The switch box is checked and cleaned. Kjdpekcgynsfx Aa Esfa If necessary, electronic components are replaced with new ones. The PLC and HMI (human interface) are replaced with the latest Schneider M340 version including the latest software.

See details

Listing