Case Clamp

Gannomat Concept Easy

Condition: new, Year of construction: 2026, FLAT PANEL CASE CLAMP GANNOMAT "CONCEPT 70 EASY 170" Fully equipped in standard configuration with: - Sturdy, torsion-resistant steel frame made with welded and bolted construction - Lateral pressing beam with continuous pressure surface, equipped with a 25 mm thick coated support plate - Counter-pressure surfaces (side pressure wall, base) are continuous, 25 mm thick coated support plates - Electromotoric adjustment of the pressing beam via precision trapezoidal threaded spindles (with increased pitch and concentric accuracy) and high-performance carriage nuts with grease reservoir - Pressing is performed by electromotor via worm gear motor (0.75 kW) - The pressing force of the pressing beam is infinitely variable and electronically set via potentiometer, regulated by frequency converter, allowing completely wear-free pressure force control - Pressing force for vertical pressing beam: min. 300 daN (kg) up to stepless max. 2200 daN (kg) - Pressing and adjustment speed of the pressing beams with fine positioning, via 3-stage selector switch: 5 / 10 / 25 mm per second - Jog mode for precise positioning of the pressing beam, e.g. for low pressing forces such as drawers, etc. - Extremely simple operation via two separate pushbuttons; two motion sequences (open/close) can be selected via controller - Freely adjustable pressing time preselection 0–30 min (switchable to seconds or hours), with individually programmable opening dimensions for both pressing beams - Re-pressing function to increase or decrease the pressing force during the pressing process - Working height/loading height: 200 mm - Working dimensions: Length min: 150 mm, max: 1300 mm Height min: 150 mm, max: 1700 mm Depth: 700 mm Electrical connection: 400 Volt, 50 Hz, 16 A Ledow Sgnkspfx Apmsrp Available: at short notice

Condition: excellent (used), SCM T150 Spindle Moulder Lrjdpfx Apow Ral Hjmep Spindle diameter: 35 mm Total spindle length: 180 mm Electric spindle lift Electric fence movement Electrically adjustable tilt angle -10/45° Variable spindle speed: 3000-4500-6000–7000-10000 rpm Motor power: 5.5 kW DTR technical documentation

Condition: good (used), Year of construction: 2011, Internal flange dimensions 2340 x 1340 mm Maximum panel dimensions (20mm thickness) 2340 x 1240 mm Working chamber height 60 mm Total thrust 300 t Ljdpfx Apotwba Semjrp Maximum specific working pressure 5 kg/cm2 Press cylinders No. 6 diam 140 mm stroke 250 mm Lower moving platen (closing movement from bottom to top) Opening between press platens 230 mm Side load 1400 mm Pvc roller uncoiler Double loading table

Year of construction: 2008, condition: ready for operation (used), functionality: fully functional, * Wemhöner Basic 1000 Plus - Year of manufacture: 2008 - Very good condition, little used * Type: KT-MB-28/15-240 * With automatic pin system and inline turn-over device * 2 tables with automatic variable pin system * With Teflon coating for pre-glued foil * Foil laying system for the pin table (pre-glued foil) * Heating plate size: 2800 x 1500 mm * Maximum workpiece size: 2,540 x 1,250 mm * Membrane: Yes Ledpfoxbcudex Apmerp * Cutting station * Foil paternoster storage, 3.2 m height with 14 suspension rods * Siemens S7 PLC control * Operator panel for PLC control: SIEMENS TP 270 (touchscreen) * Automatic membrane tensioning * Installed power supply: 38.5 kW * Maximum chamber pressure: 6 bar * Maximum press opening: 150 mm * 6 cylinders with Ø 125 mm * Operating voltage: 400V 50/60Hz * Press chamber height: 40 / 60 mm * Max pressing force: 2400 kN * Hydraulic system operating pressure: 320 bar

Condition: new, Year of construction: 2025, Gannomat Concept 70 Eco Laminate – Body press with rapid traverse Technical data: Laminate body press from our showroom; Working area: width from 150 – 2,500 mm, height from 150 – 1,400 mm; depth 700 mm; - Laminate press beam at the top with 6 elements, laminate press beams on the side with 5 elements - Laminate press beams with proven tolerance compensation for tight body joints - Counterpressure surfaces are 40 mm thick, coated, continuous support plates - The pressing force of the press beams is continuously adjusted electronically via 2 potentiometers and set via a frequency converter, therefore, the torque transmission is absolutely wear-free. - Pressing force for horizontal press beams min. 500 daN (kg) to continuously max. 2200 daN (kg) Ledpfx Asiidm Nopmorp - Pressing force for vertical press beams min. 300 daN (kg) to continuously max. 2200 daN (kg) - Including option: Rapid traverse speed for quick positioning of the press beams, controlled via automatic workpiece detection with sensors in the press beams, pressing speed 5/10/25 mm/sec. and rapid traverse speed 50 mm/sec, the sensors can be switched off for pressing special parts. - Tapping mode for precise positioning of the two press beams, e.g. for low pressing forces, drawers and bodies at 45 degrees. Simple operation via 6 separate push buttons, freely adjustable preselection of pressing time with automatic opening, loading height 300 mm The machine is in our showroom and can be delivered immediately. Location: in stock at 54634 Bitburg - immediately available -

Condition: new, Type SK-1000-P6 Working width 1000 mm Min.working length 500 mm Lredpfx Aedmi Nijpmsp Working thickness 2-150mm Polishing roller speed - Frequency control Feeding speed 3-12,5 m/min Total motor power 13.87 kW Disc motor 1.5 kW*1 Cross motor 1.5 kW *1 Screw roller motor 2.2 kW *2 Feeding power 2.2 kW Up and down motor 0.37kW*4 Swing motor 0.37kW *2 Working table up and down 0.55 kW Transport dimensions 3650x1850x2100mm Weight 4200 kg

Condition: ready for operation (used), For sale: a conveyor belt with dimensions of 1x3 meters, ready for operation. Ledpfx Apjt R R T Tomerp ✅ Length: 1x3 m ✅ Belt width: 0.4 m ✅ Transport can be arranged ✅ A wide selection of conveyor belts is available on site Please contact us. We will help you choose the right conveyor belt to meet your needs.

Condition: as good as new (ex-display), Year of construction: 2026, Swivel spindle: Yes 0 to 45° Height adjustment: handwheel / electric Swivel adjustment: Handwheel / electric Milling jaw adjustment: manual Height display: Digital display Swivel angle display: Digital display Milling stop indicator: mech counter Milling spindle diameter: 30 mm Speeds: 3000, 4500, 6000, 7000, 10000 Motor power: 7 kW Motor brake: Yes, automatic Suction connection: 2 x 120mm Machine length: 2599mm Machine depth: 900mm Lodpsuzkxxofx Apmsrp Weight: 655kg

Condition: new, Year of construction: 2026, warranty duration: 12 months, total width: 2,300 mm, total length: 1,300 mm, total height: 2,450 mm, type of input current: three-phase, Powder paint booth, suction wall TQ2020 Working dimensions (mm): 2000 (width) x 2000 (height) x 400 (depth) Overall dimensions (mm): 2300 (width) x 2450 (height) x 1300 depth SPECIFICATION: • Fan power 2.2 kW, • Efficiency 10,500 m³/h, • 3 x 100% polyester filter • Filtration degree at the level of 99.9%, • Control panel IP 66, • Automatic filter cleaning • Hermetic lighting IP 65. • Paint tank Booth available immediately (Stock status) CHOOSE BUMEX SP. Z O.O. Ledpjd S N Szefx Apmsrp Very high quality machines among those offered on the market. Professional advice and service. Warranty. Warranty and post-warranty service. Full technical documentation. 100% satisfaction of our customers. All BUMEX SP. Z O.O. brand products are EC certified. We offer our own transport - prices are set each time, for a given offer. We issue VAT invoices. Short lead times! Possibility to order machines in various, personalized configurations and dimensions! Please contact us.

Condition: used, Holz Her Accura 1556 Premium fully equipped, modern edge banding machine First delivered in 2021 Machine is in EXCELLENT CONDITION Available from stock in Lieboch Lodpfx Asyfndaepmorp