3
passage width : 900 mm
passage height : 150 mm
table surface : 1140x1300 mm
Roller diameter : 196 mm
Weight : 800 Kg
Mafle : 2700 X 1310 X 1525 mm
working height : 800 mm
Dgzjykknc
All information without guarantee.
A demonstration under power is possible at any time in our exhibition hall.
6
Make: Illig
Model: VHW 90/2
Year: 1995
Availability: Immediately
Max Material Width: 900 mm
Max Material Thickness: 1.8 mm
Bnmcoq0d9r
Total Connected Load : 36.0 kW
Max Temperature Heating Rolls: 140 °C
Material Wrap Around: 563 Grad
4
The Illig SB 74/10 C DIN thermoforming machine is used to make blister packs, it consists of a forming table (a heating zone of the material which is then thermoformed under vacuum) and a cross-cut area per plate which is routed at the end of the line by a conveyor belt.
All mobile modules of the basic machine are driven by the pneumatic system. All machine functions can be performed during the running-in of the machine in manual mode. After determining the perfect parameters, the machine opera...
6
working pressure: 6 bar
workpiece height max.: ohne Tisch: 350 mm
workpiece height max.: mit Tisch: ca.150 mm
foil width: ca.800 mm
cycle time: 32 sec
control: Siemens S5
voltage: 220 AC V / Hz
total power requirement: 119 kVA
weight of the machine ca.: ca. 9,5 t
space requirements of the machine approx.: L:11,0xB:6,0xH:4,8 m
Ewbgcox
THERMO FORMING MACHINE for vacuum forming and laminating of interior panelling in vehicle construction with films and textiles.
Additionally to this Machine a Lamin...
15
Bed size 880 x 630 mm
Outer edge seal 950 x 700
Inside edge seal 880 x 630
Double heater
6 heat settings for the top heater
Ojdgl
1 setting for the bottom heater
Vacuum pump included
Vacuum tanks included
Top air ramp for blowing domes
4
1 Universal forming machine ILLIG Typ UA 100 ED + BE-P for sheets
with sheet loader and upper pre heating device
max. forming area 960 x 560 mm
max. sheet size 1000 x 600 mm
Cvciago8
max. depth 300 mm positive/negative
year 1985
- top heater ceramic elements whole field regulation
- bottom heater ceramic elements whole field regulation
- parallel clamping frame
- 4 cooling fans
- pre blow- and blow off automatic
- plug assist
- automatic control of foil sacking by photo cell
- front door for ...
4
System includes (1) Punching Machine R+S TECHNIK 6R7 HVV, table dimensions: 1765x2735mm (2) 2x Thermoforming System R+S TECHNIK, table dimensions: 2475x1806mm, pressing force: 2500kN (3) material magazine.
Bqn2z7i9t7
6
Manufacturer Illig
Model VHW 90b
Year 2005
Condition Very good
Max material width 900 mm
Max material thickness 1.0 mm
Max temperature of heating rolls 140 °C
Material wrap around 563 Grad
Total connected load 36.0 kW
Illig communication Profibus
All details are subject to change and/or errors. All equipment is subject to availability and/or prior sale.
0al9fwz9
15
Machines direct from the manufacturer!
The ORIGINAL made in AUSTRIA!
ULTRAFORMER
The Multi-Tasking Thermopress-Unit!
>A TRULY UNIVERSAL MACHINE with endless production opportunities.
>Infinite possibilities in WOOD, PLASTICS and SPECIAL COMPONENTS MANUFACTURING.
>REALISATION of challenging and demanding projects.
ULTRAFORMER 6 in ONE production capabilities:
● THERMOFORMING of plastics with a thickness of up to 6mm!
The permanent hot air stream allows you to thermoform difficult plastics on a ...
4
The machine is constantly in use,
Cclr3esv
Pickup possible after agreement
15
Completely automated machine for production of plastic flower pots and cups:
- Thermoshape group:
Max. diameter of the article – 140 mm
Max. height of the article – 160 mm
- Productivity:
Article 0.5 l – 900 pcs/hour
Article 0.3 l – 1100 pcs/hour
31 kg/hour
- Heaters power – 2.3 kW
- Size:
Length x width x height – 1120 x 1220 x 2040 mm
Crystalizer and Dryer type Conair, USA, together with the Extruder making one continuous system for producing PET sheet from 100% waste material.
...
4
Punching press DSB 65 V with transport and moveable upper table
Dlcgwoyio
Closing force 50 to, max. punching area 600 x 390
waste winder
1
Technical details on demand.
Bo7l2awrim
Make Illig
Model RV 74b
Year 2008
Approx Hours 19,500
Condition Excellent
Delivery date Immediately
Location UK
Stations Three
Maximum forming area 704 x 514 mm
Minimum forming area 400 x 250 mm
Depth of Draw 120/40 mm
Max film width 760 mm
Sheet thickness range 0.18 - 2 mm
Operating pressure 2 bar
Max dry cycles / min 30
Bnl8sh9z8q
All details are subject to change and/or errors. All equipment is subject to availability and/or prior sale.
6
Fomring - Cutting - Stacking
Cvcjipq8
Technical details
Max. Forming Area cutting station:870x650 mm
Depth(positive & negative): 120 mm
Film Width: 250 mm min - 900 mm max
Max. Material Thickness:1.8 mm
5
3
the professional heating station for all thermoplastic materials like
Solid surface materials: Corian, Staron, LG.HiMacs, Plexicor, Wilsonart, Avonite
Plastics: ABS,PMMA, PET-G, PS, PP, PVC, PC
heating compartment approx. 3800 x 1300 x 200 mm
electrical connection approx. 24 kW, 400 V, 50 Hz, with 3 circulating air fans
Nu8sh
an extendable support surface with grating, grid 30 x 30 mm
Circulating air fan for exact temperature distribution
electronic temperature control
Time preselection with ala...
Heater regulations card Geisds machines
Bof8tuw0wm
4
Mould: 900x1900mm, punching force: 15kN, mould part height: -450 to 400mm, heating system: IR control field, top and bottom heating, controls: SIEMENS S5.
Oh7n7
Make Illig
Model RDKP 54g
Xnpsb782
Year 2010
Approx Hours 28,000
Stations Three
Delivery Date Immediately
Max Forming Area 560 x 410 mm
Max Tool Size 585 x 435 mm
Depth of Draw 120 / 120 mm
Max Material Width 610 mm
Max Mould Closing Force 120 kN
Max Cycles-Minute 55
Forming Pressure 6-10 bar
Approx Total Length 5030 mm
Approx Total Width 3420 mm
Approx Total Height 2680 mm
All details are subject to change and/or errors. All equipment is subject to availability and/or prior sale.
Forming size: 680 x 540 mm
Film max width: 750 mm
Material thickness: 0.20 -2.00 mm
Top + bottom heating plates (New in 2018)
Forming station with:
- Top and Bottom forming table / Indramat servo drive
- 2-station pneumatic clamping
Transport Chain with Servo Drive
Hole punching with AC Drive
Ber9cgol3v
Cutting station Typ DSB 72 VKU with moveable bottom table / AC Motor
Stacking station
15
1
Armrests for the automotive industry were coated on the line.
2rq9jq
Technical data see data sheet.
4
1 Universal forming machine ILLIG Typ UA 200/G for sheets
Eakuhcq9s
max. forming area 1950 x 950 mm
max. sheet size 2000 x 1000 mm
max. mold height 700 mm with double heating
year 1992, 91,2 kW/146 Amp.
- top heater ceramic elements 3 zone regulation with single on/off
For size reduction
- bottom heater ceramic elements 3 zone regulation
- All production data and heating adjustments can be stored on a disc
- parallel clamping frame with quick frame locking system for top and bottom...
15
1 Hydraulic double upright press 400 to
in the overhauled TOP STATE
ATTENTION see PDF offer in the attachment in cooperation with
our press specialist / partner company -company EP Pressentechnik/RNB / Mr. Eiblmeier
We also offer general 100% service in all areas and
New - and used presses,special field a.o. Composite,extensive references in the industry are available!!!!
Manufacturer: INO Press - Pressentechnik Waiblingen(constructor Mr. Eiblmeier)
Model/Type 100 K-400
Year of manufacture 2000
...
Manufacturer Kiefel
Model KMD 78 BFS
Year 2008
Condition Excellent
Approx hours 18,000
Delivery date Immediately
Stations Three (with BFS facility)
Maximum forming area 760 x 540 mm
Minimum forming area 375 x 270 mm
Max tool dimensions 780 x 560 mm
Depth of draw 150 mm +/-
Sheet thickness range 0.2 - 1.8mm
Max film width 810 mm
Operating pressure 6 bar
Puq7im
Max dry cycles / min 70
All details are subject to change and/or errors. All equipment is subject to availability and/or prior sale.
E...
Thermoforming machine with central lubrication pump, upper u. Below heating plates, pneum. Upper stamp, ILLIG stacking.
Molding surface (mm) 680x450
Foil width (mm) 700
Deep drawing height (mm) 125
The machine is still in production but will be transported to our warehouse from next year. All offers are valid until the day of loading.
Control system Siemens S5 and Mitsubishi for servo
Bgsjamzp79
Extras:
- Servo chain transport
- Transmission in 2007
- ILLIG VHW 72 pre-heating
- ILLIG RS 75b ...
3
Heating element with infinitely variable power controller
Ø 3,3 mm
working lengths: 550 mm
Water cooling:
Bjgbiz7rlo
A system operating on the gravity principle with a 50 litre drink, 1.5 litre water protection (against algae formation), a submersible pump (230 V, 90 W) with on/off switch, a reducing valve (to be mounted on the outlet side), 2 x 1.5 m hose, 6 hose clamps, bending template type BS Beta 550
1
Sectional refurbished in 2012
forming area 750 x 540 mm
Bcbgf2d0dh
max. material width 800 mm
depth of draw 150 mm positive/negative
molds are not available
4
System includes: (1) Product Inlet, circuit board dimensions: 1100-1950x1500-2100mm (2) Clamping Gripper Conveyor (3) Heating Station, working surface: 2x 2000x2250mm (4) Forming Station, closing force: 300kN, clamping surface: 1500x1700m, top/ bottom clamping plate stroke: 600/ 900mm.
Bljcpga2fr
4
Manufacturer Illig
Model RDM 50K
Year 1994
Condition Used
Approx Hours 29,000
Max forming area 500 x 280 mm
Depth of draw 150 / 15 mm
Max material width 525 mm
Materials PP / PS
Max cycles / min 20
Bk9g03hngo
Notes All details are subject to change and/or errors. All equipment is subject to availability and/or prior sale
7
Material : PS / PVC
Bervutionb
Cutting diam. : 110,8 x 84,7 mm
Inserts: 125, 200, 250, 350, 500 ml
5
Maximum plate size 2060 x 1060 mm
Max thickness plate 10 mm
Manual board loading / unloading
Plate pressing frame stroke 650 mm
Pneumatic plate pressing frame actuation
Closing force of plate pressing frame 30 kN
Mold bearing table race 970 mm
Pneumatic mold holder table actuator
Closing force 24 kN
Cooling fans No. 4
top heater 52 kW
Ceramic resistors Nr. 80 each 650 W
Lower heater 32 kW
Bncvdc2gul
Ceramic resistors Nr. 80 each 400 W
Individual heater resistant control
Vacuum pump 100 m3 / h
P...
Forming Area:: 560x500mm
Film Width: 560mm
foil thickness: min 0,2mm - max.0.9mm
Depth of draw pos/neg: 140mm
Bk3pdqdiqc
Materials: PET, PVC, PP, PS, HIPS
Condition - in use, in production
Location: Bucharest, Romania, 050192
Other details:
- forming - cutting
- the documentation in original + scan pdf.
- we have the software saved
- working pressure: 6 bar
- voltage: 3x400V + N + PE, 50Hz
- cycle time: min 5, max 18/minut
- weight of the machine ca.: . 1,2 t
- space requirements of the ma...
9
max. forming area 1200 x 1150 mm
Wb2n3iqk2
max. sheet size 1250 x 1200 mm
max. depth 620 mm
2
Clamping surface top/ bottom: 1600x1200/ 1780x1780mm, closing force: 90kN, withdraw force: 30kN, stroke: 1100mm, opening stroke: 1350-2450mm.
G37rmykjo
VERY LOW PRICE!!!
Manufacturer TFT
Model FCS 780 IM
Year 1999
Condition Used
Stations In Mould Cutting and Stacking
Max Tool Size 780 x 570 mm
Hours approx. TBC
Bjhicvrezv
Depth of draw 130 / 130 mm
Max material width 810 mm
Max Sheet Thickness 1.8 mm
Max mould closing force 60,000 daN
Maximum cycles-minute 45
Forming pressure 7 bar
Notes
All details are subject to change and/or errors. All equipment is subject to availability and/or prior sale.
8
Material : PP
Cavity: 10
Bervu3zubc
Cup Diameter: 71 mm
KIEFEL Model: KL 1 SH 52 BFS + KVH 83 Preheating
Zeichnung Nr.34.322-08.35, Ident.Nr. 100-035, Tp-Nr.-157/93
Year of construction - 1993
Forming Area: 540x420mm
Film Width: 570mm
Foil thickness: min 0,2mm - max.3mm
Depth of draw pos/neg: 140mm/140mm
Materials: PET, PVC, PP, PS, HIPS
Condition - in use, in production
Location: Bucharest, Romania, 050192
Other details:
- cutting in mold + punching + stocking
- Preheating for PP foil, model KVH 83, 2050/2200/2550mm, Lenght 2950mm, Width 1400mm, Wei...
max. forming area 2440 x 1540 mm
dismantled und stored in warehouse
Bkqjqfoe
6
Make: Lit Seng (Authorised Kiefel Mould Maker, Asia)
Year: March 2018
Product: PET Apple Punnet
Designed for: KMD78 (4-stations)
Usage: < 1million cycles (Almost new)
Output rate: Up to 20 cycles/minute
Cavities: 6
Form method: Pressure-forming with vacuum-assist
Features:
Punnet to hold up to 1KG of fruits
Has 4 ventilation holes at the bottom
Sharp definition thanks to pressure-formed
Bky37ocum7
Has denesting lugs, suitable for auto-packing or hand-packing purpose
All detail...
4
Material : PP
Cavity: 6
Lid Diameter: 127 mm
Fvdpk39w
Make Illig
Model HSA 50d
Year 2003
Condition Used
Delivery Date Immediately
Approx Hours 16,600
Maximum forming area 500 x 300 mm
N2qjp
Minimum forming area 100 x 35 mm
Positive depth of draw 80 mm
Maximum material width 500 mm
Maximum cycle rate 20 / min
Total weight 3,800 kg
All details are subject to change and/or errors. All equipment is subject to availability and/or prior sale
12
Forming area max. mm 480 x 250
Depth of draw neg. mm 100
Gwco2w
Material width max. mm 500
Weight kg 5000
Video of the machine: vimeo.com/414555101
VERY LOW PRICE!!!
Manufacturer TFT
Model FCS 870 IM
Year 2002
Condition Used
Stations In Mould Cutting and Stacking
Max Tool Size 870 x 650 mm
Hours approx. TBC
Depth of draw 130 / 130 mm
Max material width 900 mm
Max Sheet Thickness 1.8 mm
Max mould closing force 60,000 daN
Maximum cycles-minute 40
Forming pressure 7 bar
Bjhic9cknw
Notes
All details are subject to change and/or errors. All equipment is subject to availability and/or prior sale
7
Material : PP
Cup Diameter: 68 mm
Cutting Die diam.: 72 mm
Cavities: 40
Cy7cbudko
Overhault in Dec. 2019
Make Illig
Model RV 53
Year 2005
Delivery Date Immediately
Stations Forming, Cutting & Stacking
Maximum Forming Area 500 x 350 mm
Minimum Forming Area 300 x 100 mm
Height of Forming Above-Below Material 100 / 30 mm
Maximum Cycles-Minute 20
Total Width incl Control Cabinet 1930 mm
Total Length incl roll stand 6330 mm
Total Height 2050 mm
Itgxsr2
Total Weight 3000 kg
Notes
All details are subject to change and/or errors. All equipment is subject to availability and/or prior sale.
6
With Chiller, 23 kW
Bumuayhx0
Pre-heater Kiefel KVH 83
ILLIG STAL 800 Trim Press
Forming area max. mm 680x500
Material width max. mm 720
Depth of draw neg. mm 120
Depth of draw pos. mm 120
index length max. mm 530
tool closing force kN 180
Equipment Available:
- Mould & Matic Thermorunner 4 (1998)
- Mould & Matic Pick Up Stacker (2014)
- 95mm Mould & Matic APET Mould (2008)
Make Mould & Matic (Kiefel)
Model TR 4 (Thermorunner 4)
Year 1998
Delivery Date Immediately
E2dfpk9fu
Max Mould Size 779 x 450 mm
Depth of Draw 115 mm
Max Material Width 560 mm
Max Material Thickness 2.5 mm
Max Cycles / Min 45
Punching Force 20,000 N
All details are subject to change and/or errors.
All equipment is subject to availability and/or prior sale.
This may be of interest to you
Didn't find what you were looking for? Please contact our partners for this category :
Dealer for Thermoforming machinery
Dealer for Thermoforming machinery