Extruder & extrusion lines for sale
Identified location: Ashburn (US) (Edit)
Used NRM/Marshall & Williams OPS Film Line with 8" Davis Standard/NRM Extruder. Manufactured new in 1990-1998.
The line is still installed as operated and consists of the following:
8" (200mm) Davis Standard/NRM 30/1 L/D vented, single screw extruder. The extruder is equipped with an electric heated, air cooled barrel, includes a spare screw, and driven by a 900 HP DC motor and SCR controller (upgraded in 2005), supplying a 156 RPM screw speed.
Upsteam is a Jenco gravimetric blending syste...
Granulator "Ring die extruder" (1x), Make Schlüter Maschinenfabrik GmbH Neustadt, Type PP-200, Year of construction unknown, Material Stainless steel, Rotor sizes dia. 120mm, Rotor can be cooled, Ring die , Die sizes dia. 200x45mm, Number of dies available: 2, Number of press rolls 1, Motor 6,8 KW, 380/660 Volt (Ex), With variable speed drive , With switch , Floorspace 1,6x1,1 M, Total height 1,4 M, Weight 670 KG, Extra information die sizes: dia. 200x45mm; rotor can be cooled What you can expec...
Production line for PVC composite boards JWELL PVC production line built in 2017. It is a technological line for the production of composite products based on wood flour and PVC. The co-extrusion line was mainly used for the production of composite boards, rails and facade profiles. Extruder for composite terrace boards is complete.
The line is complete, it consists of:
- SJZ 80/156 twin screw extruder, capacity 300 kg / h, 4 heating zones
- SJZ 45/100 twin screw extruder, capacity 60 kg / h, 3...
This Cappuzi extruder has been used to produce corks out of PP. The condition of the machine is very well. We have shut down and decoupled the machine ourselves.
Technical details:
Screw: 50mm
L/D: 28
Drive: 22kW
RPM: max. 140
Brprlqdsxs
The machine can be viewed in Breda and it will be delivered including complete documentation.
WEBER DS 12:22D, Year 1991
TWIN SCREW EXTRUDER
Application: PVC pipe
Output: approx. 800 kg/h PVC (powder)
Kssyn2td
Screws and Barrel very good
General condition: very good, ready for use
Delivery time: immediately
The machine is a prototype for the continuous vulcanization of rubber or silicone products and can be used horizontally as well as vertically. The vulcanization line is divided into 3 tunnel segments. The roller support is located outside the heating zones, the segments can be adjusted in height and angle to the corresponding production situation. Each tunnel segment is equipped with 12 IR short-wave heaters, a pilot sensor and a temperature sensor for monitoring the product temperature. The emi...
Double screw extruder (1x), Make Berstorff, Type ZE-25, . EO 0324/88, Screw diameter dia. 25x500mm, L/D 20, Number of heating zones: 3, Electric heating , Water cooling , DC-motor 6 KW, 200 Volt, Screw speed 0-450 Rpm, Feeding with hopper , Feeding with metering screw , Year of construction 1989, With switchgear , Sizes switchgear 0,8x1,0x2,0 M, Floorspace 1,8x0,8 M, Total height 1,1 M, Weight 450 KG, Extra Specifications incl. tempereer eenheid 3,5 KW, 380 Volt. EX. SCHROEVEN What you can expec...
Lab-spinfiber extrusion line for PET, PA6, PP and others for POY, FDY and BCF Yarns with trhoughputs of 2-26 kg.
The extrusion line contains following additional peripherie:
- Oerlikon Barmag Inject AC double gear pump for injection of liquids in melt pipe, incl. non-return valve
- Sulzer (now Promix Solutions) static mixer
- Käser Compressed air components
- Motan Drying and conveying system Luxor 50 / Metro HLB 250/1
- Fourné Vacuum pyrolysis cleaning system VHT 56 N
- Textechno tensile testin...
Stock - No.: 2008
1 used, in 2021 partly overhauled and functionally tested
compounding-pelletizing line, equipped with:
Hgrd0vv
Extruder W& P Typ ZSK 57
twin-screw 2 x Ø 57 mm – 36 L/D co-rotating intermeshing
drive 55 kW DC
screw speed up to 480 rpm,
screw depth 9,5 mm
Segmented screws and cylinder-barrels – water cooled
1x degassing port
control board incl. melt-pressure control
Additional equipment:
> vacuum pump 1,1 kW
> piston screen-pack-changer 2 x Ø 80 mm incl. hydraulic station
>...
, Ø: 80 mm, 25 L / D, brand: Technamation Deutschland. Degasser and 18.5 kw (25 hp) motor.
Dgv2nei
Throughput: 50 – 150kg/h (depending on material)
Machine is in operation for trials and productions currently.
Berstorff ZE 40 A Twin screw extruder
• Fa. Berstorff
• Type: ZE 40 A
• YOM: 1993
• Screw diameter: 43mm
• segmented Screw and Barrel
• Length/Diameter-Ratio: 33,5 and 39,5
• New Barrels: 2pieces 6D with cooling; 1 piece 1,5D
• 1 Sidefeeder (Screw diameter 34mm)
• Drive power: 42kW
• max. rotational speed: 500Upm
• Engine refurbished complete...
Make Loomis, Type piston extruder, No. 232-40DT, Material Mild steel, Stainless steel, Motor 2,2 KW, 220/440 Volt, Capacity 1606-4227cm3, Year of construction 1986, Floor space 1,5x1,5 M, Weight 3000 KG, Extra Specifications Piston Extrusion Press - Busch vacuumpomp installatie , 0,37 KW, 220/380 Volt What you can expect from Foeth: all our machines are in working condition, and at a reduced price compared to new. They are ready for shipping to any destination worldwide. You are welcome to inspe...
Twin Screw Extruder Line - Compounding
- Electric Cabinet
- Motor AC 5 kW
Blytknzhmw
- Screws 20/42 LD
- Degassing
- Side feeding
- Die Head with 2 holes , 3mm
- Water cooling
- Heatings incl.
- Waterbath
- Pelletizer
Visit and a trial with the customer is possible. (Also Video Call)
Die: 300 \ 1.4
Screws: 65 \ 30, ld, md
80 \ 30, ld, md
65 \ 30, ld, md
Working width
Em7b3u7d3
Max: 1740 mm
Min: 750 mm
Productivity
Max: 2800 kg/h
Min: 1200 kg/h
2 winders
Dosage system, sismetric
Line control, sismetric
for plasticizing any shredded plastic waste. shredded film waste was processed last.
PVC such as cable waste also possible.
Drive motor 180KW
throughput approx. 800-1000 kg p.h.
Heating of the roller by means of carrier oil.
Mode of operation:
The squeezing roller heats and kneads the plastic waste continuously to a hot pulp, the roller is continuously fed shredded material and on the reverse side
The heated plastic sausage goes through a guillotine into a dosing form.
When the mass is reached, ...
composed:
A- Extruder, brand: Sterling, 1 spindle: 60 mm Ø 25L / D, Motor: 25 CV with variable speed drive and electrical panel.
B- Head for small tube: 0.5 mm and more measures.
C- Water cooling bath: 9 meters with pump and tank.
D- Tow Truck, Brand: Mild Ltd Boston: 700x150, production motor: 1.5kw with variable speed drive.
E- Double winder with guide: 600 mm Ø.
Oydxh
IDE-o/c 192882
SINGLE SCREW EXTRUDER ME 60/3x25D
- completely overhauled and tested machine
* incl. NEW powdercoating RAL7035 LIGHT GREY
- open frame construction
- DC-drive 20 kW / screw speed max. 44 rpm
* motor and gearbox overhauled and tested
Bjgulfftlo
- NEW 1-part cylinder with water-cooled entry zone
- 5 NEW heating/cooling-elements with 5 NEW cooling fans
- 1 flange heating zone incl. NEW heating element
- 2 die heating zones without heating elements
- NEW die connection IDE M100x3
...
Double screw extruder , Make Werner & Pfleiderer, Type Continua 58/12 D, . 215600, Screw diameter 58mm, L/D 12, Oil heating make "Single", DC-motor 20,0 KW, 460 Volt, Screw speed 30-300 Rpm, Feeding with metering screw Brabander type DD-T40/200, Exchangeable segments (inclusive extra screw segment), Year of construction 1983, With switchgear , Sizes switchgear 0,6x1,6x2,1 M, Floorspace extruder 3,7x0,7 M, Total height 2,0 M, Weight extruder 3000 KG What you can expect from Foeth: all our machine...
PP SLEEVING MACHINE LÜERS 2 SOCKETS PER CYCLE
With ring insert device
Type: MU125-2-6-91
Built in 1991
Application: PP HT pipes
Two sockets per cycle
Tool: 1 set for 2x125 mm HT pipe
The Bellingmachine was overhauled in 2014 and modified
Condition: very good
Hablamos español
Nous parlons français
We speak English
Gfw98lh
Vacuum tank calibration (left operation), used (as new)
Manufacturer: Sandern
Type: V 63S-1-4
Year of construction: 2008
Machine no.: 086230
Operating hours: approx. 300 hrs.
Spraying tank V2A / Underframe ST-37
Fe89inj
Extrusion height: 1000 mm +/- 20 mm
Vacuum chamber: 3830 mm long, drip chamber: 170 mm
Level control with float control for spray operation
Extrusion range: 8 - 63 mm Ø
Number of spray tubes: 2
Number of spray nozzles: 88
Vacuum pump: 4.0 kW
Spray pump: 1,5 kW
Servomotor: 0,25 kW...
: 75 mm Ø and 22L / D, brand: TPV, type: M75L / D22. Motor: 27.8 Kw, d.c. with variable speed drive. Year 2000
Bryb8brh0g
IDE-o/c 192888
SINGLE SCREW EXTRUDER ME 60/4x25D
- completely overhauled and tested machine
* incl. NEW powdercoating RAL7035 LIGHT GREY
- open frame construction
- DC-drive 20 kW / screw speed max. 44 rpm
* motor direct flanged on the gear box, U-shape
* motor and gearbox overhauled and tested
- NEW 1-part cylinder with water-cooled entry zone
- 5 NEW heating/cooling-elements with 5 NEW cooling fans
- 1 flange heating zone incl. NEW heating element
- 2 die heating zones without heating el...
Single screw extruder (1x), Make Lalesse Arnhem B.V., Type Universeel, No. 75-704, Year of construction 1976, Screw diameter 47mm, Screw length 600mm, L/D 12, Number of heating zones: 2, Electric heating , AC-motor 11,0 KW, 380 Volt, With variable speed drive , Screw speed ± 20-123 Rpm, Feeding with hopper , Number of temperature controllers: , With switchgear , Floorspace 2,3x1,3 M, Total height 1,7 M, Weight 1140 KG What you can expect from Foeth: all our machines are in working condition, and...
SINGLE SCREW EXTRUDER BATTENFELD UNIEX 1-45-30
Application: PE PIPES
Year of construction 1998
Motor: 61 KW
Output: approx. 160 kg / h PE
Condition: Very good, currently still in production.
Will be available in March 2021
Sachal Extrusionsmachines
Hablamos español
F3zvsoj
Nous parlons français
We speak English
, 1 pin: 120 mm Ø, brand: Erema. Magnetic tunnel agglomerator feeding the belt, double degasser and cutting under water, with a centrifuge. Silo mixer: 2 Tn and cooling tower.
Brybxzirvr
IDE-reference 99000001
CONVEYING UNIT 3050D BELIKO
- 2nd hand, never used, never installed
- made by KOCH-Technik
- incl. separate blower 3,0 kW
E7f2knzfm
- conveying capacity up to 600 kg/h (acc. to manufacture)
WILL BE DELIVERED LIKE SHOWN
Single screw extruder (1x), Make Lalesse Arnhem B.V., Type LA-85, Year of construction unknown, Screw diameter 85mm, L/D 11, Number of heating zones: 4, Electric heating (3x 4,5 KW + 1x 3,0 KW), AC-motor 30 KW, 380 Volt, With variable speed drive (frequency inverter), Feeding with metering screw , Number of temperature controllers: , With switchgear , Floorspace 2,5x1,2 M, Total height 2,4 M, Weight 1450 KG What you can expect from Foeth: all our machines are in working condition, and at a reduc...
VACUUM CALIBRATION TANK
VT 250/2/5,8 m
Year of construction 2021
Kiq38c2l
Diameter 250, 2 chambers, 5,8 meters long
made of VA, inox
Electric feed
Support rollers adjustable
Bypass pipe with filter
125 mm Ø, 35 L / D, Eurotecno: brand, with forced feeding, degasser. 160Kw motor, 250 hydraulic filter changer, thread head. Bathtub and RIETER 200 noodle. Year 1999. Spindle second hand for change. Production of 500Kg / H.
Ox9mp
IDE-o/c 204011
SINGLE SCREW EXTRUDER ME 60/5x25D
- NEW machine from IDE-stock program
Cxo882v
- open frame construction
- AC-drive 37 kW / screw speed max. 73,5 rpm
* motor direct flanged on the gear box, Z-shape
- 1-part cylinder, smooth with water-cooled entryzone
- 5 heating/cooling-elements with isolated ceramic heaters
- 1 flange heating zone
- 4 die heating zones
- die connection IDE M70x2
- extruder hopper (round), 60 liters
with 3-pos-sliding system with linear guidings
- extruder co...
Double screw extruder (1x), Make Leistritz, Type ZSE-110, . 86.02.1822, Screw diameter 110mm, L/D 20, Co-rotating , Number of heating zones: 4, Electric heating , DC-motor 10-110 KW, Year of construction 1986, With switchgear , Sizes switchgear 120x70x230 CM, Floorspace 4,7x1,4 M, Total height 2,2 M What you can expect from Foeth: all our machines are in working condition, and at a reduced price compared to new. They are ready for shipping to any destination worldwide. You are welcome to inspect...
KAESER BB 88 C TURNING PISTON BLOWER, PVC POWDER FEEDER
Unit: BB 88 C.
0fj7iv8r
Year of construction: 2007
Pumping speed: 5.07 m³ / min.
Final pressure (abs): 1.01 bar
Maximum pressure difference: 500 / mbar
Rated motor power: 7.5 KW
Block speed: 4,270 rpm
Condition: very good
Hablamos español
Nous parlons français
We speak English
corrotating, brand: OMC, type: EBV 31 / 32D, year 2001. Composable spindles of 31 mm Ø. Book type shirt. 11 Kw motor with water cooling variator and wire head. Installed total power: 25 kw.
Brwys0mupo
IDE-o/c 204014
SINGLE SCREW CO-EXTRUDER MEB 20/5x25D
- NEW machine from IDE-stock program
- mobile on 4 swivel castors
- manual height adjustment ± 200 mm via threaded spindle
- control cabinet integrated in the frame
- control via PLC Control 20/4
* operation via 5.7" touch panel
* screw on/off
* screw speed
* screw speed display
* display motor load
* heating on/off/lowering value
- emergency stop button on the control cabinet
- incl. connection cable 5 m long with CEE plug 32 A
- ...
Single screw extruder "Pin extruder" (1x), Make Kraftanlagen Heidelberg, Type ST-350/6D, No. 91.02 4295916, Year of construction 1991, Screw diameter 350mm, L/D 6, With jacket , DC-motor 180 KW, 440 Volt + 53,7 KW, 400 Volt, Inlet 350x285mm, Screw can be heated , Without switchgear , Floorspace 5,5x1,7 M, Total height 2,0 M, Weight 11.000 KG, Extra Specifications - With die head for 167 strands - With die face cutter - Extruder can be used for PVC What you can expect from Foeth: all our machines...
