Used Susemihl Gmbh Maschinenfabrik for sale (67,324)

Condition: new, Year of construction: 2026, Equipment: safety light barrier, 1A Gmatick Storage Paternoster (roll rack) The foil storage Paternoster foils is suitable to use for the storage of all 3D-films, it is used as a high storage at the membrane press or as a space-saving storage solution for the 3D foils. With our Paternoster you can storage on very small area approximately 2, 4m x 1, 2m a lot of film rolls (up to 32 rolls of a Ø 300 mm). The required film is thus immediately available at the push of button. Our Paternoster are available from 2.8 m up to 6, 0 m as standard Paternoster. Also special solutions are offered by us, please contact us, we will then find the right solution for your storage. As additional equipment we offer center sleeves, a manual cutting station or the full automatic cutting device and we have also ionization solutions available at Gmatick. • Storage rods ø 42.4 mm • Sleeves inside Ø max. 82 mm,. Gkodpfx Ajff Huwecmjd • Load chain as a hollow pin chain with a breaking load of 100 kN, • Chain pitch is 50 mm hole to hole and this is the raster for the positioning of the mounting foil bars. • Control with a key switch (dead man) for on / off • Rotational speed of the chain is approx. 5.5 m / min • Voltage 400 V, 3N; 50/60 Hz or as USA Version 480V 60Hz • Mains cable with CEKON plug 16A fuse protection (by the customer) 10A slow blow • ground load data at least 2, 2 kg / cm² • Side covering over the entire height of the Paternoster, guards from 2, 2 m above floor to top edge of the Paternoster. • Requirement for the installation of the Paternoster is a viable, flat and solid floor, • Floating floors you can’t install a Paternoster. It is forbidden

Condition: excellent (used), Year of construction: 2002, machine/vehicle number: Reg Nr. 976, Machine Name: Paddle dryer Used Manufacturer: AVA / Holland Merten GmbH Gkjdpsitcvuofx Acmsd Type: HTK 200 Construction year: 2002 Speed: 107 U/min Pressure range: -1 to 3 bar (drying chamber), 6 bar in the double jacket Material: Stainless steel Driving force: 5,5 KW Model: EExdellCT4 Total content: 235 Liter Parts in contact with product: Stainless steel 1.4571 Gear box: Stirnradgetriebemotor Equipment: Double jacket, mechanical seal, shaft heater Dimensions: L 3400 x W 1100 x H 1500 mm Empty weight: approx. 1600 kg Message: Operating temperature 130°C Design temperature 200°C Internal pressure mixer -1/+3 bar Pressure double jacket +6 bar Accessories: Base frame, Double coat, Mechanical seal, PT100 thermometer, Shaft heating with Maierkopf HWR 225, Sight glass, Technical documentation. Condition: Used very good Price: on request

Condition: repair required (used), Year of construction: 1985, functionality: limited functionality, machine/vehicle number: 11710519, spindle bore: 1,250 mm, spindle motor power: 56,000 W, quill travel distance: 1,000 mm, workpiece weight (max.): 1,600 kg, Equipment: documentation/manual, Machine type: CNC vertical lathe Manufacturer and model: Schiess AG - Schiess Moweg GmbH; Type 12DS100 Schiess Year of manufacture: 1985 Serial number: 11710519 Technical condition: Machine in working order; used, requires repair Technical specifications: Working range: Table dimensions - Pallet D=1000 [mm], max. turning height H=800 [mm], max. turning diameter D=1250 [mm] Tailstock stroke S=1000 [mm]; adjustable cross slide - positioning every P=500 [mm] Table load capacity: 1600 kg Control system type: Siemens - Sinumerik 840 D Main drive power - 56 kW; Maximum rotational speed: 500 rpm Axis positioning accuracy: 0.02 [mm] - axis measuring system: optical scales Axis feed rate - "rapid": 6000 mm/min Axis feed rate - "working": 0.1 - 2000 mm/min Cutting fluid - yes - through the tool Number of axes: 2-axis lathe Drive type: servo drives Additional equipment: Tool magazine: 12 positions Material feeding system: loading station at the pallet magazine Palletizing system - 2 pallet magazine; pallet loading station; machine table - a total of 2 pallets Gsdpfx Acszvnbxsmekd Chip transport system - yes Cooling system - control cabinet air conditioning - yes Operating manual - paper version in Polish and German, digital version in German Currently, the machine has been disassembled from the hall and is ready for loading into a container. Arranging for the container and the company that will load the machine into the container is the responsibility of the buyer.

Condition: good (used), Year of construction: 2023, functionality: fully functional, type of input current: three-phase, total height: 1,200 mm, total width: 790 mm, total length: 1,200 mm, input voltage: 380 V, ground cable length: 3,000 mm, overall weight: 205 kg, warranty duration: 12 months, type of cooling: water, hose package length: 5,000 mm, input current: 16 A, laser power: 2,000 W, laser wavelength: 1,080 nm, Equipment: documentation/manual, type plate available, Handheld Laser Welding Machine AIRTECH 2kW – Top Technology for Efficient Sheet Metal Welding Godpfx Acjn Sl Dbjmskd Demonstration Unit – Excellent Condition Discover the smart and high-performance solution for precise laser welding: the Airtech handheld laser welding system with 2,000 watts of power! Perfectly suited for demanding sheet metal fabrication – efficient, safe, and highly versatile. Highlights and Features: - Power output: 2,000 watts for superior weld quality and speed - Laser wavelength: 1080 nm, continuous operation with modulation frequency up to 20 kHz - Handheld laser welding head – ideally designed for ergonomic operation - Robust housing and intelligent internal structure for maximum durability - Touchscreen display for intuitive operation - Optional automatic multifunctional wire feeder - Safety features: three-color alarm, safety interlocks, and protection against operating errors - Cooling via separate water circuit with 13-liter tank capacity - CE-certified components according to European standards Your Benefits - Work safely thanks to comprehensive protection mechanisms and alarm systems - Flexible applications, including automatic wire feed and robot integration - Low operating costs and easy maintenance due to well-designed engineering and long-life components For more information or consultation, the Airtech team will be happy to assist you!

Condition: ready for operation (used), Year of construction: 1999, functionality: fully functional, input voltage: 400 V, input current: 21 A, type of input current: DC, volume flow: 6,045 m³/h, overall weight: 1,100 kg, ALKO ECO JET 60/5 HD extraction unit, without control software. Gkodpfxoyrqnzj Acmod Dust extraction unit, chip extraction, self-cleaning filter, vacuum-based ALKO ECO JET. The filter is pneumatically cleaned with pulses of compressed air during operation, ensuring high device efficiency. It is ideally suited for all types of dry dust generated in various technological processes. Filter bags can be replaced according to specific requirements and intended use.

Condition: new, Equipment: lighting, Take your painting process to a new level - with mobile convenience. Mobile paint booths in container design for painting and coating various objects. They are specially designed for mobility so that they can be easily transported and set up on different construction sites. The booth is usually equipped with a ventilation system to ensure air quality, lighting and a filter system that prevents paint mist from escaping. The ventilation system ensures that the vapors and particles released during painting are kept inside the booth so that there is no danger to the environment. Mobile paint booths are a practical and flexible solution for companies that need an effective painting system that can be moved from one construction site to another at any time. Overview of the design and functions Our mobile 20-foot Sapi painting containers consist of a robust steel frame with welded wall and ceiling panels. Inside, we can add special equipment such as cranes or lifting devices. The floor is made of tear plate. There are ventilation grilles in both door leaves, which are fitted with fine-pored filter mats. One leaf is designed as an escape door for safety reasons and has a viewing window. It should also be mentioned that these are not simply converted shipping containers! We manufacture all our containers from scratch ourselves. We only use the most stable materials that meet the requirements and have also been tested and proven in terms of safety. Normal shipping containers would not meet the required safety standards. Paint extraction system in the mobile painting container The paint mist extraction wall for paint mist separation is located in front of the rear wall and is equipped with multi-layer filter mats. The extraction wall consists of a galvanized housing, edged with baffle plates including various suspension and fastening elements for the filter equipment. The powerful and EX-protected extraction fan with drive motor is installed on a console in the rear wall area on the outside of the container. Next-generation mobile spray booths: meeting EU requirements and advancing coating solutions The new generation of mobile spray booths must meet the highest EU requirements. The consideration of new paint systems such as hydro paints, polyurethane resins, epoxy-zinc dust or epoxy-iron-mica paints places high demands on existing paint booths. That is why we have developed a new and unique mobile paint booth for the next generation of coating solutions. Gsdpfjun Shgjx Acmjkd An important criterion is the transportation of the workpieces for painting and for further processing steps. Do you need more information? Our engineers can offer expert advice and support. Whether paint mist dry separation or wet scrubbing, air humidification or air drying, condensation drying in a low-temperature process or hot air drying, whether pre-treatment of the workpieces by high-pressure washing with water flow in a circulation system or by compressed air blasting or wheel blasting technology.

Year of construction: 2024, condition: new, functionality: fully functional, machine/vehicle number: CO2-1125-5000, 1x Vacuum Belt Filter Completely constructed in stainless steel 1.4404/1.4571, grates in stainless steel 1.4301 Finish: pickled and passivated Including: 1x drive roller 508x1427 1x steering roller 88.9x1850 6x support/tension rollers 88.9x1850 1x VBF frame 1x VBF hood frame 1x safety grilles (1.4301) 2x spray pipes, each fitted with 12 nozzles 6x hood brackets for vacuum tube 1x mounting materials, incl. gaskets 1x holder for control valve and paddle 2x slide blocks for tension roller HMPE100 2x bearing blocks for scraper blade HMPE100 1x scraper blade HMPE100 1x drive SEW KH87/T R57 DRN90L4TF 2x bellows d100 wbz 100-E1 2x misalignment switches 2x emergency stop switches 2x emergency stop cords 1x pressure reducer 1x hose and coupling for connection to bellows 23x nozzle holders 23x nozzles Gksdpjxfvahofx Acmed 4x rubber seals for wash cabinet 1x rubber seal for suspension conveyor 2x double wash gutters

Year of construction: 2026, condition: new, functionality: fully functional, overall weight: 120 kg, total length: 900 mm, total width: 1,550 mm, total height: 2,050 mm, input frequency: 50 Hz, laser power: 30 W, laser wavelength: 1,064 nm, type of cooling: air, type of input current: AC, laser type: fiber laser, The universal laser marking system LAS 28 XLe from Systemtechnik Hölzer GmbH can be used for a very wide range of marking applications. With the integrated fiber laser you can mark almost all materials such as steel, carbide, aluminum and plastics. Depending on the requirements, the system can be equipped with a 20, 30 or 50 watt fiber laser. For permanent marking, the use of the laser is necessary in many industries. With the powerful laser software, texts, numbers, 2D codes, QR codes and logos can be realized with just a few clicks without extensive programming knowledge. Serial and article numbers are automatically incremented by the software after prior setting. In addition, the software can read data (variable information such as drawing numbers, project designations, etc.) from existing tables and automatically transfer them to predefined areas. The use of a hand scanner is also possible. The standard equipment includes an integrated PC with Windows operating system and laser software. Optionally, the laser model LAS 28 XLe can be equipped with a rotary axis (3-jaw chuck) for marking cylindrical parts. Further options, such as lateral extension arms for marking long parts, movable Z-axis, drawer systems, etc., can be realized. Made in Germany Fiber laser 30W, 20 W or 50 Watt - Laser class 1 - Wavelength 1064nm - Marking field size 150x150mm (optionally larger) - marking software EZCAD in German / English - optional: rotary axis (3-jaw chuck) - optional: digital height measuring system - optional: exhaust system (incl. activated carbon filter) - pilot laser (simple preview, contour preview) - focus finder (simple focus adjustment) - signal light for indication of operating status - max. component height approx. 300mm - electrically adjustable Z-axis - Integrated PC with Windows operating system - frame made of aluminum profile - air cooled - Door width approx. 700mm / door height(pass-through): 400mm - Connection 230V - Dimensions: approx. 900 x 800 x 1900 mm (LxWxH) - Weight: approx. 100 Kg Gkjdpszntfmjfx Acmod

Year of construction: 2020, condition: used, functionality: fully functional, machine/vehicle number: 376292, The Reitz KXE 250-050030-00 is an industrial centrifugal fan designed to generate a high total pressure increase in process installations. The assembly consists of a volute fan casing, an impeller mounted on a separately supported shaft, a coupled electric motor, and a common steel base frame with vibration-isolating mounts. The KXE design is suitable for moving air and process gases in systems requiring high flow rates and pressure. This unit was manufactured in 2020 for a rated volume flow of 500 m³/min and a total pressure increase of 2500 daPa. At its operating point, it delivers 602.4 m³/min at 1862 daPa and 3033 rpm. The shaft is supported by two 6318 bearings lubricated with Shell Gadus S2 V100 2 grease. Gkodpfx Acozw Ucxomed Manufacturer: Konrad Reitz Ventilatoren GmbH & Co. KG Type: KXE 250-050030-00 Product type: industrial centrifugal fan Serial number: 376292 Year of manufacture: 2020 Material number: 10466442 Measurement category: C Efficiency grade: N61 Target efficiency grade value: 64.5 Rated inlet temperature: 20°C Operating-point inlet temperature: 40°C Rated inlet medium density: 1.205 kg/m³ Operating-point inlet medium density: 0.93 kg/m³ Rated volume flow: 500 m³/min Operating-point volume flow: 602.4 m³/min Rated total-pressure increase: 2500 daPa Operating-point total-pressure increase: 1862 daPa Optimum efficiency: 76.3% Rated shaft power: 256.57 kW Operating-point shaft power: 231.1 kW Rated rotational speed: 2980 rpm Operating-point rotational speed: 3033 rpm Maximum rotational speed: 3159 rpm Maximum medium temperature: 80°C Drive-end bearing: 6318 Non-drive-end bearing: 6318 Lubricant: Shell Gadus S2 V100 2 Initial relubrication interval: 2460 operating hours Subsequent relubrication interval: every 2460 operating hours Grease quantity per bearing: 132 g Conformity marking: CE

Year of construction: 2020, condition: used, functionality: fully functional, machine/vehicle number: 376295, The Reitz KXE 250-050030-00 is an industrial centrifugal fan designed to generate a high total pressure increase in process installations. The assembly consists of a volute fan casing, an impeller mounted on a separately supported shaft, a coupled electric motor, and a common steel base frame with vibration-isolating mounts. The KXE design is suitable for moving air and process gases in systems requiring high flow rates and pressure. This unit was manufactured in 2020 for a rated volume flow of 500 m³/min and a total pressure increase of 2500 daPa. At its operating point, it delivers 602.4 m³/min at 1862 daPa and 3033 rpm. The shaft is supported by two 6318 bearings lubricated with Shell Gadus S2 V100 2 grease. Manufacturer: Konrad Reitz Ventilatoren GmbH & Co. KG Type: KXE 250-050030-00 Product type: industrial centrifugal fan Serial number: 376295 Year of manufacture: 2020 Material number: 10466442 Measurement category: C Efficiency grade: N61 Target efficiency grade value: 64.5 Rated inlet temperature: 20°C Operating-point inlet temperature: 40°C Rated inlet medium density: 1.205 kg/m³ Operating-point inlet medium density: 0.93 kg/m³ Gksdpozw Ug Refx Acmed Rated volume flow: 500 m³/min Operating-point volume flow: 602.4 m³/min Rated total pressure increase: 2500 daPa Operating-point total pressure increase: 1862 daPa Optimum efficiency: 76.3% Rated shaft power: 256.57 kW Operating-point shaft power: 231.1 kW Rated rotational speed: 2980 rpm Operating-point rotational speed: 3033 rpm Maximum rotational speed: 3159 rpm Maximum medium temperature: 80°C Drive-end bearing: 6318 Non-drive-end bearing: 6318 Lubricant: Shell Gadus S2 V100 2 Initial relubrication interval: 2460 operating hours Subsequent relubrication interval: every 2460 operating hours Grease quantity per bearing: 132 g Conformity marking: CE

Condition: used, functionality: fully functional, The IBD Wickeltechnik industrial unwinding-shaft assembly is designed to support and controllably unwind rolls of web material. It incorporates an unwinding shaft supported by KL.S-series foot-mounted safety chucks, a CX.250.4 single-disc pneumatic brake, and forced cooling from a 24 V DC fan. The safety chucks allow for rapid shaft loading and removal, while the locked closure secures the journal during operation. The brake uses four pneumatic calipers, a 250 mm self-ventilating cast-iron disc, and a modular design that enables control of the braking torque through air pressure. The assembly is mounted on an adjustable, wheeled steel transport frame. Gsdjzw Uilspfx Acmskd Manufacturer: IBD Wickeltechnik GmbH Device type: industrial unwinding-shaft assembly with pneumatic brake Safety chuck model: IBD-KL.S.O.1800.0380.1.40.VT Safety chuck series: KL.S Safety chuck configuration: foot-mounted Maximum shaft and roll weight: 1800 kg Maximum safety chuck torque: 380 Nm Square journal range: 30–40 mm Triangular journal size: 36 mm Brake model: CX.250.04.28.0/V.24 Brake type: pneumatic, single-disc, air-cooled Number of brake calipers: 4 Brake disc diameter: 250 mm Disc material: cast iron Minimum braking torque: 6 Nm at 0.2 bar Maximum braking torque: 640 Nm at 6 bar Maximum permissible brake speed: 2500 rpm Fan voltage: 24 V DC Safety chuck serial number: 6800.37879.1/47.18 Brake serial number: 6800.37879.12/47.18

Condition: good (used), functionality: fully functional, Year of construction: 2024, The bunker conveyor from Lange Fördersysteme is for sale; it was previously used by a manufacturer of medical technology equipment. Conveyor belt length: 2100 mm Discharge height, side: 1600 mm Usable width: 190 mm Gksdpfozyr Nbsx Acmsd Cleats: 20 mm high, spaced 130 mm apart Container size: L: 1500 mm, W: 580 mm Spindle for discharging the bulk material Mounted on adjustable feet Base frame: L: 1800 mm x W: 1000 mm

Condition: used, Ex-protected filter unit, extraction system, central extraction cartridge - impulse filter P. RIES GmbH Type 330 D ATEX Cartridge filter system, rectangular filter unit, central welding fume extraction Machine no. 10011932 Year of manufacture: 2020 - as new, unused Airflow rate: 3,300 m³/h Airflow rate: 0.9 m³/sec Filter area: 20 m² (1 piece cartridge filter) Differential pressure: 3,300 Pa (33 mbar) Extraction connection at filter inlet: 2x Ø 150 mm Exhaust connection at filter outlet: sound insulation hood Compressed air connection: approx. 8 bar Motor power: 3 kW Mains connection: 400 Volt, 50 Hz - Explosion-protected design ATEX II 2Db 125°C / 3G T4 Gsdpfx Aoy N Duqjcmekd - Pneumatic rotating filter cleaning, manual via push button - Manometer for differential pressure display (vacuum display in mbar) - Service door for filter replacement - Filter stage 1 = 1 cartridge filter Ø 325 mm, length 900 mm P-RIES, type cartridge filter 20.1 m², BGIA/IFA class M, antistatic - Filter stage 2 = filter outlet (sound insulation hood) equipped with 9 activated carbon filter cartridges, type AKZ 2500V, 266 m³/h per filter cartridge - Built-in radial fan, type IE 3-premium efficiency, 12% improved efficiency - Robust steel construction in RAL 7035 light grey, antistatic powder-coated - Dirt collection container as pull-out drawer approx. 70 litres (440 x 530 x 300 mm) - EC Declaration of Conformity, operating instructions with wiring diagram available Required space (L x W x H): 670 x 700 x 2430 mm Weight extraction unit: 211 kg Transport dimensions on pallet (L x W x H): 930 x 1350 x 1950 mm Weight incl. transport pallet: 236 kg As new, unused, ex stock

Condition: used, KB Prüftechnik Hardness Testing Machine, Type: KB 750 BVRZ Machine Type: KB 750 1 kg - 750 kg UNIVERSAL DIGITAL KB universal hardness testing machines for automatic and standard-compliant hardness testing. Suitable for all hardness testing methods in the load range HV 0.2 1 - 3000 kgf, Vickers, Brinell, Rockwell, Super-Rockwell, Knoop (only HK 1), ball indentation hardness (plastics) and depth measurement according to Vickers and Brinell. Fully automatic testing sequence, evaluation of the indentations on the integrated LCD monitor using an integrated video camera and zoom lens guarantees the highest evaluation accuracy according to the standard. All hardness values are displayed digitally immediately. User-friendly and powerful control panel with a color LCD monitor, high contrast and glare-free. The measurement of the indentation is performed without parallax. The testing forces are electronically controlled and applied with the highest precision. The video image can optionally be output as a BMP file. All KB hardness testing machines are supplied with a basic equipment package that enables immediate operation with the ordered indenters. A selection of fixtures, testing tables, indenters, lenses, hardness comparison blocks, etc. is available. A connection to a PC or central computer is possible with all KB hardness testing machines. In conjunction with the fully automatic software and motorized cross table, the machine can be operated as a fully automatic system. fully automatic testing sequence optical evaluation via integrated video evaluation extremely user-friendly and powerful large LCD color display industrially designed foil keypad variable software adaptation Zoom lens 1:7 parallax-free measurement load cells, controlled load application, LED lighting Rockwell resolution 0.025 HRC extremely powerful 200 freely definable test programs Calibration machine accuracy (option) new LED ring light (option) automatic image evaluation (option) 2 interfaces parallel + serial, as well as keyboard connection extended load range XL (option) freely switchable language selection German, English, French, Italian KB750 BVRZ: Test load 3-750 kgf Brinell ISO 6506 HB depth measurement Vickers ISO 6507 HV depth measurement Rockwell ISO 6508 Rockwell ISO 6508 Superrockwell Testing table ∅80 mm Motor zoom 1:7 Lens 4x for HV10-HB5/750 NOT suitable for HV5 Operating function: Programmable digital panel with the following functions: Measurement of the hardness indentation on the LCD display, with adjustable measuring marks, without parallax Logically structured, simple operating guidance Any number of test programs can be created and stored (200) Gkjdpfx Acjzg Tyuemsd Automatic force selection by selecting the testing method Freely selectable application times of the testing forces Freely selectable dwell times of the testing forces Online help Automatic correction for curved surfaces according to DIN EN ISO Control of the fully automatic testing sequence Direct, digital hardness value display Tolerance display Conversions according to DIN 50150 Table B1 Protocol generation in DIN A4 format with standard printer via parallel interface Serial interface for data output to PC Optional network 4 languages: German-English-French-Italian Statistics functions, such as: Number of tests Min / Max Average Range Standard deviation cp / cpk Histogram (Changes and errors in the technical data are subject to change!)

Year of construction: 2020, condition: used, functionality: fully functional, machine/vehicle number: 07.019.0000.00 / 114247 / 006, The mobile nozzle pack installation device from Theilen Maschinenbau is designed for lifting and positioning nozzle packs during assembly work. The welded frame structure is mounted on four swivel castors and features side handles for manual movement. The upper working beam is raised by a centrally mounted hydraulic hand jack and guided by two vertical guide elements. The beam is fitted with adjustable supports and mounting pins. The maximum load capacity is 200 kg. The device was manufactured in 2020 and bears CE marking. Safety symbols indicate a hot surface, an overhead hazard and the required use of head, hand and eye protection. Gkedpfx Ajzw T Duscmod Manufacturer: Theilen Maschinenbau GmbH Type: Nozzle pack installation device Number: 07.019.0000.00 / 114247 / 006 Year of manufacture: 2020 Maximum load capacity: 200 kg Lifting mechanism: Hydraulic hand jack Construction: Welded frame structure Undercarriage: 4 swivel castors Beam guidance: 2 vertical guide elements Conformity marking: CE

Condition: new, Year of construction: 2025, Parker-Airtech presents the latest generation of nitrogen generators, which impress with an outstanding air factor on the market. Our systems are characterized by the exclusive use of high-quality components, which ensures their longevity and reliability. The cost-effective operation of the system is characterized by low power consumption with maximum output, low-maintenance operation of the system, no additional gases such as hydrogen to reduce oxygen and high-quality and durable components. This means that the system can be amortized in the shortest possible time. An intelligent monitoring system enables continuous monitoring of the operating parameters and ensures that you are always informed about the status of your system. Whether in the office or on the go - our system can also be conveniently viewed on your mobile phone, so that you always have control over your nitrogen production. The system is individually tailored to your needs. Gkjdpfx Asnq Dkijcmsd Parker-Airtech has made it its mission to offer you the best technologies to optimally support and maximize your processes. Trust in innovation, quality and performance - choose Parker-Airtech.

Year of construction: 2022, condition: like new (used), functionality: fully functional, machine/vehicle number: WDW-70056, WDW – Calibrated containers – Continuous weighing scale for weighing wood pellets or other pellet-shaped bulk goods, complete with a discharge unit. Performance / throughput: 15.6 tons/hour; weighing accuracy: +/- 0.01 kg; cycle times: approximately 2 weighings per minute; the photo shows a representative image; the machine is delivered in its original packaging. Gsdez Ixc Iepfx Acmjkd

Condition: like new (used), Year of construction: 2022, functionality: fully functional, total length: 9,500 mm, total width: 1,000 mm, overall weight: 3,000 kg, Silo discharge screw conveyor for dried or wet sawdust. The system is in new condition and comes in its original packaging. The photo is a sample image – the system has never been installed. Discharge screw conveyor for silo internal diameter of 8.9 m. Discharge rate: 40 m³ per hour. Drive power: 15 kW. Godpoz Ix Iqefx Acmjkd Lower section: for accommodating the screw conveyor drive, feed drive, main shaft with metering device, and bearings, discharge chute, and blockage sensor. Upper section: with screw shaft, cross-roller swivel joint, and cover hood. Electrical control system is not included!

Condition: used, Year of construction: 1988, machine/vehicle number: 112 009 00, Na sprzedaż sprawna maszyna przemysłowa renomowanej niemieckiej marki Ramisch Kleinewefers GmbH (rok prod. 1988, nr fabryczny: 112 009 00). W zestawie znajdują się dwa dodatkowe, duże wałki (cylindry) na zmianę/wymianę, co pozwala na dostosowanie maszyny do różnych procesów i materiałów. Gkedpfxszz Iz Nj Acmjd Stan techniczny: Maszyna w pełni sprawna, w dobrym stanie, gotowa do pracy. W zestawie: Kalander + 2 kompletne wałki wymienne (np. o innej twardości, strukturze lub powłoce). Zastosowanie: Przemysł tekstylny, wykończalnictwo tkanin, obróbka włóknin, gładzenie, prasowanie, embossing/tłoczenie lub przetwórstwo tworzyw sztucznych. Jakość: Solidna, ciężka, zachodnioniemiecka konstrukcja (Made in Western Germany).

Condition: new, Year of construction: 2025, power: 5 kW (6.80 HP), SAPI Premium 200-liter pressure blast machine with cyclone cleaner and abrasive vacuum for abrasive treatment. This blasting system provides a cost-effective, highly economical, and effective solution for open blasting work with semi-automatic abrasive recycling. Godpfowc Rcnsx Acmjkd Open blasting system for manual sandblasting of many different types of workpieces using a blaster with abrasive treatment. The abrasive is collected by hand after blasting and pushed into the collection hopper on the floor. The abrasive vacuum extracts the abrasive from the hopper and pulls it through the cyclone cleaner. The dust is extracted and collected in the dust container of the vacuum. Coarse particles are separated by a sieve. The cleaned abrasive falls back into the vented pressure blast pot and is available for reuse. Our SAPI safety shut-off ensures a safe and economical blasting process. The remote control allows you to start and stop the blast pot using a hand lever mounted on the blast hose package. This is a highly economical and effective solution for open blasting operations with semi-automatic abrasive recycling. The scope of delivery includes: SAPI Premium 200-liter blast pot with 1 1/4" piping, pressure-regulated from 0.1 - 12 bar, max. operating pressure 12 bar High-performance 1 1/4" water separator, permanently installed on the unit SAPI safety shut-off device Cyclone cleaner for abrasive preparation with lifting device Abrasive sieve (inserted sieve in the blast pot hopper) Filling hopper 500x500x380 mm 4-meter connecting hose from the filling hopper to the cyclone cleaner 3-meter connecting hose from the cyclone cleaner to the abrasive vacuum cleaner Abrasive vacuum cleaner 5.5 kW, 400 V, 50 Hz with 70-liter dust container 10-meter blast hose package 25x7 mm, fully assembled with nozzle holder, hand lever, control line, and blast hose coupling Boron carbide Venturi long nozzle (diameter optionally 6 mm) mm, 8 mm or 10 mm)

Condition: good (used), Year of construction: 2001, functionality: fully functional, Manufacturer Fasti GmbH Gkjdpfx Acsvzwrbemsd Model ERD 65 B Connected load 0.9 kW

Condition: new, Year of construction: 2026, 60cm Endless UV LED Digital Scan Camera CCD Visual AI Printer Scan and print simultaneously - No more stencils - any application required Gjdpjv N H Hwefx Acmskd - Different images at the same time - Huge speed advantage Material width: 600mm ENDLESS LENGTH due to conveyor belt Material height: 150mm (Higher throughput available upon request) Recommendation: 3x Ricoh Gen5 for CMYK + White (listed price) 4x Ricoh Gen5 for CMYK + White + Coating (additional charge approx. €3,500) Includes vacuum table Includes conveyor belt Includes operator computer Includes CCD Visual AI camera system Depending on the number of heads, 12 - 40 sqm/h or more With 2 heads, approximately 12 sqm per hour is possible Machine dimensions: 1250mm x 1750mm x 1400mm (LxWxH) Weight: approx. 300 kg + pallet Machine power: 2000 W

Year of construction: 2023, condition: new, Nitrogen self-generation plant for the production of a wide range of purities, pressures and volume flows. Consisting of high-quality components, such as filters, adsorbers, nitrogen separation unit of the company Parker Hannifin and the compressor manufacturer Käser. If you need high pressure compression we cooperate with Bauer Kompressoren. More than 400 units have been installed at our customers. Gz7iapb All plants are assembled by us and adapted according to your space conditions and needs. We also plan and realize container plants for outdoor and indoor installation. We are looking forward to your inquiries... Gkodpfenq Di Tox Acmod

Year of construction: 2026, operating hours: 2 h, condition: as good as new (ex-display), 1 Hydropneumatic press type STHP 60 kN with two-hand operation - floor model with and without base frame The compact and handy table model has a hydropneumatic drive with pressure intensifier which can increase the punching force up to 5 times. During the working stroke, the punching cylinder is pressurised with oil by the pressure intensifier and thus has a purely hydraulic punching stroke. The return stroke is performed directly with compressed air. The adapter that can be screwed into the piston rod of the working cylinder makes it possible to install special tool holders. Gkodpfepn Unvox Acmed

Year of construction: 1989, condition: ready for operation (used), Polymer storage tank Article no.: RE-HU-2019-0602-B38-e Product: Used polymer storage tank container Material: GF - UP / Leguval W 17 (glass fiber reinforced polyester resin with top layer) Manufacturer: Theodor Vanck GmbH Dimensions: diameter 2.40 x height 2.80m Godpfx Acjd Hgc Usmskd Volume: 12 m3 Year of construction: 1989 Fabr. No .: 55163