Used Susemihl Gmbh Maschinenfabrik for sale (68,340)

Condition: repair required (used), Year of construction: 2010, operating hours: 7,700 h, functionality: not functional, machine/vehicle number: 15158-10, working range: 4,000 mm, sheet thickness (max.): 12 mm, sheet thickness steel (max.): 12 mm, CNC plasma cutting system BACH ThermoCut 2000 with pipe cutting device, TEKA dust extraction system, and plasma source. Manufacturer: BACH Maschinenfabrik GmbH Type: ThermoCut 2000 Year of construction: 2010 For sale is a used CNC plasma cutting system BACH ThermoCut 2000, including pipe cutting device, plasma source, dust extraction system, and complete piping. The system was used in our machine manufacturing company until recently and is suitable for cutting sheet metal as well as processing pipes. Technical data: Working area: 4,000 x 2,000 mm Plasma source: Thermal Dynamics Ultra-Cut 100 CNC control: myBach Prjdpfxozizkys Ac Aeb Pipe cutting device included Pipe diameter: min. 50 mm max. 320 mm Max. cutting thickness: Mild steel: up to 12 mm Stainless steel: up to 10 mm TEKA filter and dust extraction system included Complete dust extraction piping system included CE marking available Maintenance and condition The system was regularly maintained during its entire service life. Official maintenance by the manufacturer was last performed on August 20, 2013. After that, ongoing maintenance was carried out in-house. Filters of the TEKA dust extraction system were renewed approximately 6 months ago. Cutting torch head was renewed approximately 4 years ago. Cooling water filter is changed regularly, approximately once a year. The operating hour counter of the dust extraction system currently shows approximately 7,700 hours. Since the system was operated exclusively with the dust extraction system running, this value can be used as a good indication of the total operating time of the system. Known defect The system is currently not operational. After consultation with Voortman and Mr. Sobiech from Magma Industries, the cause is likely to be in the cooling circuit of the plasma source. According to the experts, the most likely causes of the fault are: Defective cooling water pump Defective flow sensor Leakage on the suction side of the cooling water system A final fault diagnosis has not yet been carried out. Spare parts for the installed Thermal-Dynamics plasma source are now only available to a limited extent. The machine is therefore explicitly sold as a system requiring repair or for refurbishment. Scope of delivery BACH ThermoCut 2000 CNC system Thermal Dynamics Ultra-Cut 100 plasma source Pipe cutting device TEKA filter and dust extraction system Control panel with controller Dust extraction piping Accessories according to existing equipment Special features ✅ Pipe cutting up to Ø 320 mm ✅ Complete package including dust extraction ✅ Solid industrial machine made in Germany ✅ Easy-to-disassemble gantry design ✅ Also interesting for buyers who already have a suitable plasma source Location 24161 Altenholz, Germany Price Negotiable €21,900 Inspection possible by appointment. Sale exclusively to commercial businesses, excluding any warranty for defects. Loading / Dismantling The system is offered exclusively for self-dismantling and self-collection. The buyer assumes full responsibility for the dismantling, loading, and removal of the machine at their own cost and risk. To assist with loading, a hall crane with a maximum lifting capacity of 10 tons is available on site. Use of the crane can be arranged in advance. Due to the size and weight of the system, we recommend an inspection before submitting an offer.

Year of construction: 1983, condition: used, Yeast cultivation with dampable wort sterilization tank designed for an operating pressure of 2 bar and a capacity of 2.47 hl, a second heatable and coolable wort sterilization tank designed for an operating pressure of 2 bar with a capacity of 12.7 hl, and a yeast propagation tank with a capacity of 55 hl, permissible operating pressure of 2 bar and jacket cooling in the lower third (without cone). All tanks are equipped with an agitator. Also includes a CIP tank. The plant is controlled via a Steinecker control cabinet (time-controlled). The tanks are also available individually Predpfevcqt Usx Ac Ajb Additional title: with switch cabinet and CIP tank Features: 2 tanks for wort sterilization with stirring unit (approx. 2,4 hl and approx. 12,7 hl), control cabinet, 1 cylindro-conical tank with stirrig unit, CIP system

Condition: new, Year of construction: 2026, machine/vehicle number: K00629, functionality: fully functional, operating hours: 2 h, power: 3 kW (4.08 HP), input voltage: 400 V, input frequency: 50 Hz, cutting height (max.): 320 mm, cutting width (max.): 320 mm, control type: PLC-controlled, total height: 2,100 mm, total length: 2,600 mm, total width: 2,000 mm, Equipment: CE marking, documentation/manual, lighting, With the bandsaw automation system SA 320 ZA, the Sägemaschinenfabrik Bauer GmbH offers a powerful, fully automatic sawing solution for demanding series production. The robust, column-guided design ensures the highest cutting accuracy, long service life, and reliable operation – even in multi-shift operations. Prsdszqdtyjpfx Ac Aob Whether in the steel trade, metal construction, mechanical engineering, or contract manufacturing, the SA 320 ZA impresses with its high productivity, ease of operation, and durable quality.

Condition: new, Year of construction: 2026, machine/vehicle number: K00630, functionality: fully functional, operating hours: 5 h, power: 2.2 kW (2.99 HP), input voltage: 400 V, input frequency: 50 Hz, cutting height (max.): 600 mm, cutting width (max.): 430 mm, control type: PLC-controlled, pivoting range: 45,060 °, total height: 2,250 mm, total length: 2,150 mm, total width: 4,000 mm, Equipment: CE marking, documentation/manual, When it comes to precise miter cuts, high production volumes, and economical manufacturing, the BAUER VG 450 L ZA-2 is the ideal solution. This fully automatic miter band saw combines the proven sawing technology of the VG 450 L with a powerful material feed system, enabling virtually operator-free sawing operation. The integrated automatic material feed system independently transports the material to the sawing station and positions it precisely for each individual cut. At the same time, the machine automatically monitors the end of the material. The sawing process is completed reliably. Prodpozqdv Iefx Ac Ajb A particular highlight is the ability to produce frame components with miter cuts fully automatically. Different cutting angles are executed precisely and with high repeatability, making the VG 450 L ZA-2 ideal for the production of windows, doors, facades, steel structures, and metalwork. Angle profiles, rectangular tubes, square tubes, round tubes, and solid materials can also be processed reliably and economically. The hydraulic miter adjustment allows for cutting angles from 45° left to 60° right, enabling numerous frame constructions to be produced without manual adjustments.

Condition: reconditioned (used), power: 11 kW (14.96 HP), operation weight: 8,000 kg, Horizontal baler DIXI 80 SLD 2018-2021 Year of construction Semi-automatic 80-tonne baling system for the economical volume reduction of residual materials (recyclables) in industry and trade: Cardboard packaging Tetra packaging Films PET bottles Foam Insulation boards and other compressible materials. Machine dimensions L x H x W approx. mm: 4,320 x 1830 x 2,154 mm Filling opening W x H (standard) mm: 1,040 x 1,110 mm Machine weight approx. kg: 8,000 Press force max. kN: 80 t / 800 kN Ironing cycle (average value) approx. s: 35 Bale size W x H x L approx. mm: 1,120 x 1,120 x 1,200 Bale weight (depending on material) approx. kg: 550 - 650 Binding: manual Number of bindings: 4, with wire with Quicklink wire Drive power: 11 kW; 400V/32A The presses are tested and functional and are offered with a fresh UVV and inspection in accordance with DGUV regulation 3. The Dixi 60SLD is ready for immediate use. On request, the Dixi 60 SLD can be completely overhauled for an additional charge. Predpfx Asqa Dq Doc Ajb This includes: Replace all hydraulic hoses. Change the hydraulic oil and check the hydraulic unit. The hydraulic cylinders are checked and replaced if necessary. Net price plus VAT and possible transportation. The operating instructions are available and are supplied as a PDF file and in paper form.

Condition: reconditioned (used), Horizontal Press Baler DIXI 60 SLD Year of manufacture: 2014 Semi-automatic 60-ton baling system for economical volume reduction of residual materials (recyclables) in industry and trade: Cardboard boxes Tetra packaging Foils PET bottles Foam Insulation boards and other compressible materials. Pjdpfjnfux Uex Ac Asrb Machine dimensions L x H x W approx. mm: 4150 (5080) x 1725 x 2035 Feed opening W x H (standard) mm: 990 x 1110 Machine weight approx. kg: 5420 Pressing force max. kN: 60 t / 600 kN Ironing cycle (average value) approx. s: 47 Bale size W x H x L approx. mm: 800 x 1100 x 1200 Bale weight (depending on material) approx. kg: 370-410 Binding: manual Number of bindings: 3, with wire with quick release eyelets Drive power: 7.5 kW; 400V/32A The presses are tested and functional and are offered with a fresh UVV and inspection in accordance with DGUV regulation 3. The Dixi 60SLD is ready for immediate use. On request, the Dixi 60 SLD can be completely overhauled for an additional charge. This includes: Replace all hydraulic hoses. Change the hydraulic oil and check the hydraulic unit. The hydraulic cylinders are checked and replaced if necessary. Net price plus VAT and possible transportation.

Condition: new, Year of construction: 2026, machine/vehicle number: K00627, functionality: fully functional, operating hours: 2 h, power: 1.8 kW (2.45 HP), input voltage: 400 V, input frequency: 50 Hz, cutting height (max.): 240 mm, cutting width (max.): 450 mm, control type: manual, pivoting range: 45,060 °, actuation type: manual, total height: 1,300 mm, total length: 2,000 mm, total width: 850 mm, Equipment: CE marking, documentation/manual, The S 320 DG from Sägemaschinenfabrik Bauer GmbH is a powerful double-miter band saw designed for demanding applications in metal construction, mechanical engineering, steel construction, as well as in locksmith shops and manufacturing companies. Thanks to its robust industrial design, high cutting accuracy, and well-thought-out construction, it is ideally suited for economical and precise cutting operations in daily continuous use. Podpfxszqdmms Ac Ajrb With a generous cutting capacity of Ø 320 mm for round stock or 450 x 230 mm at 90°, the S 320 DG offers high flexibility for a wide range of workpieces and material cross-sections. Miter cuts from 45° to the left to 60° to the right enable versatile applications in the cutting of profiles, pipes, and solid materials.

Condition: new, Year of construction: 2026, machine/vehicle number: K00628, functionality: fully functional, operating hours: 2 h, power: 1.8 kW (2.45 HP), input voltage: 400 V, input frequency: 50 Hz, cutting height (max.): 300 mm, cutting width (max.): 1,000 mm, control type: manual, actuation type: manual, total height: 2,300 mm, total length: 1,400 mm, total width: 600 mm, Equipment: CE marking, documentation/manual, The BAUER 1000 V is the ideal vertical bandsaw for companies that want to process large workpieces with precision, efficiency, and reliability. With a cutting width of 1,000 mm and a cutting height of 300 mm, it offers ample capacity for demanding applications in steel construction, mechanical engineering, toolmaking, and industrial production. Whether it's contour cutting, straight cutting, or processing large-format components, the BAUER 1000 V combines maximum stability with the highest cutting accuracy and long-lasting quality. Pjdpfx Acozqdphs Aerb

Condition: new, Year of construction: 2026, machine/vehicle number: K00626, functionality: fully functional, operating hours: 2 h, power: 2.2 kW (2.99 HP), input voltage: 400 V, input frequency: 50 Hz, cutting height (max.): 600 mm, cutting width (max.): 430 mm, control type: manual, actuation type: manual, total height: 2,500 mm, total length: 2,600 mm, total width: 1,800 mm, overall weight: 1,200 kg, Equipment: CE marking, documentation/manual, rotational speed infinitely variable, BAUER Vertical Band Saw VG 450 L Precision and performance for demanding miter cuts The BAUER VG 450 L was specifically designed for the precise sawing of steel, stainless steel, aluminum, and other metals. Thanks to its robust machine construction, hydraulic miter adjustment, and intelligent cutting pressure control, it offers the highest cutting quality with simultaneous ease of operation. Pedoznc Spjpfx Ac Ajrb Whether for individual parts, series production, or workshop use, the VG 450 L impresses with its reliability, precision, and efficient operation.

Condition: like new (used), Year of construction: 2016, operating hours: 500 h, functionality: fully functional, spindle speed (max.): 24,000 rpm, Gravograph IS 6000 IQ – CNC engraving machine – approx. 500 operating hours Prjdpfez D Htgox Ac Asb For sale is a very well-maintained Gravograph IS 6000 IQ with only approx. 500 operating hours. The machine is suitable for engraving and milling operations, for example, for the production of signs, lettering, and customized engravings. Machine data: Manufacturer: Gravograph / Gravotech Model: IS 6000 IQ Year of manufacture: 05/2016 Operating hours: approx. 500 Condition: used, very well maintained Equipment: Engraving software GS8-GRAPHIC incl. dongle Stable machine table with T-slots for workpiece clamping Matching base frame Wired handheld control unit Extraction device on the machining head Spray device 750-W HF spindle kit for the IQ series, according to the order confirmation from November 2017 The machine was purchased in December 2016. It is worth noting the excellent condition and the low usage with only approx. 500 operating hours. Price: net 14,500 EUR Location: 09627 Bobritzsch-Hilbersdorf Availability: immediately If you are interested, we look forward to receiving your inquiry.

Condition: used, functionality: unexamined, Adapter for extruder Weber DS-85 Manufacturer: Hans Weber Maschinenfabrik GmbH Type: DS 85 Condition: used Podpezzwi Ajfx Ac Asrb

Year of construction: 2024, condition: like new (used), functionality: fully functional, (Please tell us your offer price) Sale only within Europe, incl. Turkey Price without packaging; delivery condition: FCA (machine location) ===== Technical data see handout. All warranty rights are excluded. Prjdpfxsz Hax Uj Ac Aeb For the correctness of the technical data and year of construction, for the completeness of accessories and tool equipment, and for compliance with all safety and environmental protection requirements specified in the accident prevention regulations. No sale to private individuals. Sales only within Europe, incl. Turkey Price without packaging; Delivery condition: FCA (machine location) ===== Technical data please see handout in attachment. German text leading language. Without any guaranty and warranty, including completeness of tools & accessories as well as environmental and safety regulations. No private sales.

Condition: excellent (used), Year of construction: 2011, functionality: fully functional, machine/vehicle number: 2080092, Used CNC horizontal 5-axis twin-spindle double-table machining center Psdpfxoz E Ddfj Ac Aorb Manufacturer: SW – Schwäbische Werkzeugmaschinen GmbH Type: BAW06-22 Year of manufacture: 2011 Machine No.: 2080092 Weight: approx. 16,000 kg Technical data: - CNC horizontal machining center - 5-axis design - Twin spindle - Double table - Travel ranges: - X-axis: 600 mm - Y-axis: 600 mm - Z-axis: 510 mm - Rapid traverse: up to 45 m/min - Tool interface: HSK-A63 - Spindle speed: up to 17,500 rpm Equipment: Machine with standard accessories. Availability: Available in the short term.

Year of construction: 2022, operating hours: 6,123 h, condition: used, functionality: fully functional, machine/vehicle number: 20-22-004, Like new, hardly used. Psdpfoziaqfsx Ac Asrb

Condition: used, functionality: unexamined, Pair of screws for extruder Weber DS-63, parallel Manufacturer: Hans Weber Maschinenfabrik GmbH Type: DS 63 Serial no.: 063.008271.r.1004 Screw diameter: 2 x 63 mm Screw length: 17 x D Condition: used Pjdjzrt Enjpfx Ac Aerb

Year of construction: 2018, condition: used, functionality: fully functional, machine/vehicle number: Gießbank 531 MAP40, General Data: - Designed for wall-mounted toilets - Low-pressure casting process with level control - Suitable for multi-part plaster molds - 40 mold stations per unit - A total of 160 mold stations - Mold spacing: 700 mm - Modular operation in units of 10 molds each - Operation with 10, 20, 30, or 40 molds in use per unit is possible - Different casting times per 10-mold section are possible Pedpfx Aoz Agv Uoc Ajrb Production Capacity - For currently manufactured "married" toilet models: the upper and lower parts are cast separately -> Two castings result in a complete toilet. 160 castings per casting cycle -> 80 complete toilets per casting cycle. - For models without "marriage": one mold station corresponds to one product -> up to 160 pieces per casting cycle. - Dimensions: Installation area approximately length: 33,800 mm, width: 4,100 mm, height: 4,300 mm. Single-row roller conveyor with a length of approximately 33,000 mm. Four lifting beam systems per unit. Each lifting beam is designed for 10 molds. One extraction trolley per unit. - Casting and slip system: Slip supply DN 100, slip return DN 100, compressed air connection 2 inches for the pressure line, filling via high-level or level tanks, two level tanks per unit, two casting lines per level tank, return of excess slip to the return slip tank, flushing of the slip lines with water and compressed air, four separate flushing systems per unit. - Mold mounting and clamping technology: Steel base frame, four lifting beams with electromechanical cable winch drive, cable breakage and cable slack protection, divisible vertical clamping devices, upper clamping beams with quick-release fasteners, pneumatic clamping hoses. - Demolding and handling: Pneumatic extraction assistance, molds can be clamped and tilted by 90 degrees, mold halves are manually separated, ergonomic transfer of the green part to a roller conveyor, two-hand safety control, quick-change system for different mold mountings, track for existing vacuum lifting system. - Compressed air and low-pressure system: Separate compressed air distribution for each 10 molds, three compressed air circuits (upper clamping beams and core boxes, vertical clamping devices, separation of the green part and mold), individual pressure control via pressure regulators, pressure monitoring of the clamping circuits, acoustic signal in case of insufficient clamping pressure, low-pressure system for stabilizing the green part in the mold and for hose drying after flushing. - Drying, ventilation, and lighting: Fans for drying the parts, diameter approximately 950 mm, LED lighting strips along the unit, active unit sections can be visually marked by the lighting, uniform drying of the plaster molds supports up to two casting cycles per day. - Electrical system and control: Two main switch cabinets, one main switch cabinet controls 20 molds and two lifting beams each, two-hand operation for safety-relevant movements, separate control cabinets on the level tanks and lifting beams. - Advantages: High production flexibility due to the 10-mold division, different products or casting times within one unit are possible, unused conversion components remain on the unit, suitable for different toilet models and production concepts, modular design facilitates partial occupancy and adjusted production quantities, extensive peripherals for casting, flushing, drying, demolding, and transport are available.

Year of construction: 2018, condition: used, functionality: fully functional, machine/vehicle number: Gießbank 532 MAP40, General Data: - Designed for wall-mounted toilets - Low-pressure casting process with level control Prsdpfoz Agw Eox Ac Aeb - Suitable for multi-part plaster molds - 40 mold stations per unit - A total of 160 mold stations - Mold spacing: 700 mm - Modular operation in units of 10 molds each - Operation with 10, 20, 30, or 40 molds in use per unit is possible - Different casting times per 10-mold section are possible Production Capacity - For currently manufactured "married" toilet models: the upper and lower parts are cast separately -> Two castings result in a complete toilet. 160 castings per casting cycle -> 80 complete toilets per casting cycle. - For models without "marriage": one mold station corresponds to one product -> up to 160 pieces per casting cycle. - Dimensions: Installation area approximately length: 33,800 mm, width: 4,100 mm, height: 4,300 mm. Single-row roller conveyor with a length of approximately 33,000 mm. Four lifting beam systems per unit. Each lifting beam is designed for 10 molds. One extraction trolley per unit. - Casting and slip system: Slip supply DN 100, slip return DN 100, compressed air connection 2 inches for the pressure line, filling via high-level or level tanks, two level tanks per unit, two casting lines per level tank, return of excess slip to the return slip tank, flushing of the slip lines with water and compressed air, four separate flushing systems per unit. - Mold mounting and clamping technology: Steel base frame, four lifting beams with electromechanical cable winch drive, cable breakage and cable slack protection, divisible vertical clamping devices, upper clamping beams with quick-release fasteners, pneumatic clamping hoses. - Demolding and handling: Pneumatic extraction assistance, molds can be clamped and tilted by 90 degrees, mold halves are manually separated, ergonomic transfer of the green part to a roller conveyor, two-hand safety control, quick-change system for different mold mountings, track for existing vacuum lifting system. - Compressed air and low-pressure system: Separate compressed air distribution for each 10 molds, three compressed air circuits (upper clamping beams and core boxes, vertical clamping devices, separation of the green part and mold), individual pressure control via pressure regulators, pressure monitoring of the clamping circuits, acoustic signal in case of insufficient clamping pressure, low-pressure system for stabilizing the green part in the mold and for hose drying after flushing. - Drying, ventilation, and lighting: Fans for drying the parts, diameter approximately 950 mm, LED lighting strips along the unit, active unit sections can be visually marked by the lighting, uniform drying of the plaster molds supports up to two casting cycles per day. - Electrical system and control: Two main switch cabinets, one main switch cabinet controls 20 molds and two lifting beams each, two-hand operation for safety-relevant movements, separate control cabinets on the level tanks and lifting beams. - Advantages: High production flexibility due to the 10-mold division, different products or casting times within one unit are possible, unused conversion components remain on the unit, suitable for different toilet models and production concepts, modular design facilitates partial occupancy and adjusted production quantities, extensive peripherals for casting, flushing, drying, demolding, and transport are available.

Year of construction: 2018, condition: used, functionality: fully functional, machine/vehicle number: Gießbank 533 MAP40, General Data: - Designed for wall-mounted toilets - Low-pressure casting process with level control - Suitable for multi-part plaster molds - 40 mold stations per unit - A total of 160 mold stations - Mold spacing: 700 mm - Modular operation in units of 10 molds each - Operation with 10, 20, 30, or 40 molds in use per unit is possible - Different casting times per 10-mold section are possible Production Capacity - For currently manufactured "married" toilet models: the upper and lower parts are cast separately -> Two castings result in a complete toilet. 160 castings per casting cycle -> 80 complete toilets per casting cycle. - For models without "marriage": one mold station corresponds to one product -> up to 160 pieces per casting cycle. - Dimensions: Installation area approximately length: 33,800 mm, width: 4,100 mm, height: 4,300 mm. Single-row roller conveyor with a length of approximately 33,000 mm. Four lifting beam systems per unit. Each lifting beam is designed for 10 molds. One extraction trolley per unit. - Casting and slip system: Slip supply DN 100, slip return DN 100, compressed air connection 2 inches for the pressure line, filling via high-level or level tanks, two level tanks per unit, two casting lines per level tank, return of excess slip to the return slip tank, flushing of the slip lines with water and compressed air, four separate flushing systems per unit. - Mold mounting and clamping technology: Steel base frame, four lifting beams with electromechanical cable winch drive, cable breakage and cable slack protection, divisible vertical clamping devices, upper clamping beams with quick-release fasteners, pneumatic clamping hoses. - Demolding and handling: Pneumatic extraction assistance, molds can be clamped and tilted by 90 degrees, mold halves are manually separated, ergonomic transfer of the green part to a roller conveyor, two-hand safety control, quick-change system for different mold mountings, track for existing vacuum lifting system. - Compressed air and low-pressure system: Separate compressed air distribution for each 10 molds, three compressed air circuits (upper clamping beams and core boxes, vertical clamping devices, separation of the green part and mold), individual pressure control via pressure regulators, pressure monitoring of the clamping circuits, acoustic signal in case of insufficient clamping pressure, low-pressure system for stabilizing the green part in the mold and for hose drying after flushing. - Drying, ventilation, and lighting: Fans for drying the parts, diameter approximately 950 mm, LED lighting strips along the unit, active unit sections can be visually marked by the lighting, uniform drying of the plaster molds supports up to two casting cycles per day. - Electrical system and control: Two main switch cabinets, one main switch cabinet controls 20 molds and two lifting beams each, two-hand operation for safety-relevant movements, separate control cabinets on the level tanks and lifting beams. Pedpsz Ag Rrjfx Ac Ajrb - Advantages: High production flexibility due to the 10-mold division, different products or casting times within one unit are possible, unused conversion components remain on the unit, suitable for different toilet models and production concepts, modular design facilitates partial occupancy and adjusted production quantities, extensive peripherals for casting, flushing, drying, demolding, and transport are available.

Year of construction: 2018, condition: used, functionality: fully functional, machine/vehicle number: Gießbank 530 MAP40, General Data: - Designed for wall-mounted toilets - Low-pressure casting process with level control - Suitable for multi-part plaster molds - 40 mold stations per unit - A total of 160 mold stations - Mold spacing: 700 mm - Modular operation in units of 10 molds each - Operation with 10, 20, 30, or 40 molds in use per unit is possible - Different casting times per 10-mold section are possible Production Capacity - For currently manufactured "married" toilet models: the upper and lower parts are cast separately -> Two castings result in a complete toilet. 160 castings per casting cycle -> 80 complete toilets per casting cycle. - For models without "marriage": one mold station corresponds to one product -> up to 160 pieces per casting cycle. Pedpfx Aozz Rpcoc Aorb - Dimensions: Installation area approximately length: 33,800 mm, width: 4,100 mm, height: 4,300 mm. Single-row roller conveyor with a length of approximately 33,000 mm. Four lifting beam systems per unit. Each lifting beam is designed for 10 molds. One extraction trolley per unit. - Casting and slip system: Slip supply DN 100, slip return DN 100, compressed air connection 2 inches for the pressure line, filling via high-level or level tanks, two level tanks per unit, two casting lines per level tank, return of excess slip to the return slip tank, flushing of the slip lines with water and compressed air, four separate flushing systems per unit. - Mold mounting and clamping technology: Steel base frame, four lifting beams with electromechanical cable winch drive, cable breakage and cable slack protection, divisible vertical clamping devices, upper clamping beams with quick-release fasteners, pneumatic clamping hoses. - Demolding and handling: Pneumatic extraction assistance, molds can be clamped and tilted by 90 degrees, mold halves are manually separated, ergonomic transfer of the green part to a roller conveyor, two-hand safety control, quick-change system for different mold mountings, track for existing vacuum lifting system. - Compressed air and low-pressure system: Separate compressed air distribution for each 10 molds, three compressed air circuits (upper clamping beams and core boxes, vertical clamping devices, separation of the green part and mold), individual pressure control via pressure regulators, pressure monitoring of the clamping circuits, acoustic signal in case of insufficient clamping pressure, low-pressure system for stabilizing the green part in the mold and for hose drying after flushing. - Drying, ventilation, and lighting: Fans for drying the parts, diameter approximately 950 mm, LED lighting strips along the unit, active unit sections can be visually marked by the lighting, uniform drying of the plaster molds supports up to two casting cycles per day. - Electrical system and control: Two main switch cabinets, one main switch cabinet controls 20 molds and two lifting beams each, two-hand operation for safety-relevant movements, separate control cabinets on the level tanks and lifting beams. - Advantages: High production flexibility due to the 10-mold division, different products or casting times within one unit are possible, unused conversion components remain on the unit, suitable for different toilet models and production concepts, modular design facilitates partial occupancy and adjusted production quantities, extensive peripherals for casting, flushing, drying, demolding, and transport are available.

Year of construction: 2021, condition: like new (used), functionality: fully functional, Component 1: ATM-800 P Tangential Dereeler (2 pieces) Heavy-duty dereeler for controlled unwinding of copper wire coils. • Max. coil diameter: 800 mm • Max. coil width: 300 mm • Pickup hole: Ø52 / Ø56 mm • Max. coil weight: 300 kg Predpfx Aoz Ap R Iec Asb • Braking force: 100 - 2000 N • Brake torque: 3 - 800 Nm • Max. speed: approx. 5 rpm • PLC control with torque sensor Component 2: HBK-40-S Automatic Taping Machine Professional automatic taping machine for coil and conductor insulation. • Servo-controlled taping head • Operator terminal and display • Integrated X-axis guidance • Electric hysteresis brake • Automatic overlap control via encoder • Suitable for various insulation materials

Year of construction: 2013, operating hours: 7,700 h, condition: repair required (used), functionality: limited functionality, machine/vehicle number: 12090, This is a recycling extruder with side feeding for materials (flakes, pellets, etc.). The system is supplied with a control cabinet and a double vacuum system. The pelletizing system is missing at the end of the screw – it is not included in the scope of supply. The cylinder ends at the flange. The extruder is supplied without a screw. The frequency inverter for the main motor was replaced with a new unit 3 years ago. Installed power approx.: 474 kW Cooling water requirement approx.: 190 l/min Fresh water consumption approx.: 110 l/h Feeding system: • Diameter of the feeding screw: 200 mm • Drive for the feeding screw: 45 kW, frequency-controlled • Hopper capacity net 7 m³/250 ft³, • Gear motor 3 × 3 kW • 2 sight glasses in the hopper • 2 level indicators Extruder: • Diameter of the extruder screw: 145 mm • L/D ratio: 24 • Heating power: 50 kW • Extruder drive unit 280 kW Vacuum 1: • Screw length: 16 L/D • Heating power: 40 kW • Vacuum pump power: 11 kW • Vacuum capacity: 225 m³/h • Vacuum pressure: 33 mbar Vacuum 2: • Screw length: 16 L/D • Heating power: 40 kW • Vacuum pump power: 7.5 kW • Vacuum capacity: 190 m³/h • Vacuum pressure: 33 mbar Cylinder: • Cylinder: Bimetal extruder cylinder, • Reinforcement layer 1.8–2.0 mm thick, • Hardness 63–65 HRC Installation conditions: • Voltage: 3 × 400 Volts • Permissible fluctuation max.: +5 % – 5 % • Frequency: 50 Hz Permissible fluctuation max.: +4 % – 4 % • Protective measure: Multiple grounding • Ambient temperature: min. 15 °C, max. 35 °C • Humidity max.: 90 % • Altitude of the installation site: 0 – 1000 m The machine was in operation at an R&D center in Israel. Since the company now operates a production facility in Europe, the R&D center is being closed. The machines will be transported to Europe at the owner's expense and can be delivered EXW at a port or at the production facility in Europe. The details for optimal transport need to be clarified. The machine price is without packaging. Pedpfx Acoznz Eze Aerb

Condition: used, Year of construction: 1999, Technical details: x-travel: 690 mm y-travel: 400 mm z-travel: 550 mm B-axis (table): 360° mm control: Siemens 840 D number of spindle speeds: max. 15 000 U/min tool clamping: System nach DIN 69893 tool taper: HSK-A63 tool changer magazine: chain magazine: 12 places Stück traversing speed: x/y/z Axis: 40 total power requirement: 195 kW weight of the machine ca.: 13,0 t Traveling Column Milling Machine - the tool changing unit consist of 3 -NC axis and 1 NC- rotary table axis - ATC ( with magazine) - rotary table Type SKH-NC 4/029, diameter=460mm , table surface plate Ø 500 x20mm, revolution per minute max. 22 rpm - control panel SIEMENS - Spindel-Typ: DRF-WE-255-N-W-15-30, 15000 U/min., Spindelleistung = 30 kW - chip conveyor Make Knoll type 400K-3/280, ejection height 1150mm - cooling system for spindle make SCHIMBKE Type DK 80V, 3,36 kW i.D. Pedpfx Acju Idl So Aerb *

Condition: used, Year of construction: 2013, functionality: fully functional, machine/vehicle number: NS-009-0000-300, type of input current: AC, nominal power at 50% duty cycle: 250 kVA, throat depth: 300 mm, short-circuit current: 50,000 A, input voltage: 400 V, type of cooling: water, total width: 1,000 mm, total length: 1,000 mm, total height: 1,850 mm, overall weight: 1,000 kg, open-circuit voltage: 22 V, Zens Multifunction Resistance Welding Machine 250 kVA MF – 23 kN – 50 kA – Year of Manufacture 2013 For sale is a high-quality Zens multifunction resistance welding machine in a robust industrial design. The system was developed for demanding resistance welding processes and is ideally suited for series production in the automotive, supplier, electrical, and metal industries. The machine operates with modern medium frequency (MF) technology and achieves a welding power of 250 kVA at a 50% duty cycle. The powerful SER medium frequency inverter (700 A) enables a maximum welding current of 50 kA and ensures maximum process stability as well as reproducible welding results. With a maximum welding force of 23 kN and an overhang of 300 mm, the system is suitable for a wide range of resistance welding applications. Technical Data Manufacturer: Zens Machine Type: Multifunction Resistance Welding Machine Year of Manufacture: 2013 Welding Power: 250 kVA (Medium Frequency / MF) at 50% duty cycle Max. Welding Current: 50 kA SER Medium Frequency Inverter: 700 A Welding Control: SER-Mega1 Maximum Welding Force: 23 kN Overhang: 300 mm Equipment CE-compliant protective enclosure CE safety light curtain Welding table for welding forces up to 23 kN Pressure compensation tool QSF-M quality assurance system Position measuring system for process monitoring PLC control (Siemens S7) Predpfx Aozqucfjc Ajb Robust industrial design for continuous industrial operation The combination of powerful medium frequency technology, precise force and position control, and modern PLC and SER welding control ensures high process reliability and consistently reproducible welding results. Thanks to the complete CE safety equipment, the machine can be easily integrated into existing production lines. The system is in good condition and can be inspected and demonstrated at any time by prior appointment.

Condition: used, Year of construction: 2021, functionality: fully functional, machine/vehicle number: 1605269/1, total width: 630 mm, total height: 1,115 mm, total length: 1,010 mm, working width: 460 mm, input voltage: 400 V, type of input current: AC, overall weight: 200 kg, power: 0.37 kW (0.50 HP), roller diameter: 100 mm, passage height: 80 mm, feed rate X-axis: 35 m/min, height adjustment type: mechanical, tank capacity: 2 l, roll width: 450 mm, input frequency: 50 Hz, workpiece height (max.): 80 mm, Equipment: double-sided, For sale is a well-maintained glue and roller application machine from Axel Wirth Maschinen GmbH, type LW 100/450. The machine was manufactured in 2021, has comparatively few operating hours, and is in technically perfect and well-maintained condition. A particular advantage is the adjustable working speed or feed rate (6 - 35 m/min). This allows the machine to be flexibly adapted to different workpieces, materials, and application media. The machine is mounted on a sturdy, mobile base with lockable wheels. As a result, it can be easily moved within the production area and safely positioned at the respective location. A total of two identical machines are available. The stated price applies per machine. An attractive package price is possible if both machines are purchased. The LW 100/450 is suitable for the uniform application of liquid and pasty media onto flat or textured workpieces, for example: - Glue and adhesive - Oil and wax - Stain and primer - Paints and dispersions - Resins and comparable application media Among other materials, wood, solid wood, parquet flooring, chipboard, cork, cardboard, metal, stone, rubber, and insulation materials can be processed. The application quantity can be adjusted via the lateral adjustment devices. The rollers and glue trays can be removed with a few simple steps, making the machine easy to clean. Technical data and equipment Manufacturer: Axel Wirth Maschinen GmbH Type: LW 100/450 Year of manufacture: 2021 Nominal width: 450 mm Working width: approx. 460 mm Passage height: approx. 80 mm Diameter of the application rollers: 100 mm Capacity per glue container: approx. 2.3 liters Drive power: 0.37 kW Adjustable working speed or feed rate Application rollers above and below Separate control cabinet Main switch and emergency stop Mobile base with lockable wheels CE marking Condition: used, well-maintained, and technically perfect Operating hours: comparatively low Inspection and test run are possible after prior appointment. Collection at the Leun location. Shipping by freight forwarder can be organized if required, upon agreement. If you have any questions or are interested, please do not hesitate to contact us. We will be happy to provide further information and photos. Prodpfx Ajzr H Aaec Asb Price: €5,900 (negotiable) per machine plus VAT (can be shown). Package price for both machines: on request All information is provided to the best of our knowledge. The sale takes place under the conditions applicable to the seller for used machines.

Condition: used, AZO E800 screening machine, centrifugal screen Completely overhauled Prjdpfx Acsz Hc Tus Asb Material: steel, coated Includes new bearings, seals for the electric motor, and rotor See our other listings.