Used Pellets for sale (277)

Condition: used, SPE Renergi Low Temperature Dryer. The Renergi Dryer is used for drying of sawdust and other materials for production of biofuels. The dryer can dry sawdust, bark or wood chips from a humidity level of about 50% to a level of approximately 10 %. This low-temperature dryer utilizes warm (or hot) water from a recommended temperature of 65°C and higher. Maximum water temperature - 110°C. Power supply safety: The dryer must only be fed by 3x400 V AC (630 A) 50/60 Hz with a separate Protective Ground conductur. Power supply Data: • Voltage 400 V AC, three phase • Recommended fuses in supply line: maximum 3x630 A • Typical power consumption: 200kW The dimension of the Dryer are roughly 17,4 by 5,7 meters, with a height of 10,7 meters. The floor space required is approximately 21,4 by 8,0 meters. A ceiling height of at least 15 meters (or 4 meters above the top of the media inlet). Air supply: at least 24 kg gas/s fresh air is required for the operation of this machine. This corresponds to 20nm3/s, or 72 000 nm3/h. Airflow: max 200 liter/min Air pressure: min 4,5 bar, recommended 6,0-8,0 bar Water supply: hot water supply, with a flow of 32 dm3/s. Water pressure: min 1.5 bar, max 6.0 bar Operating temperature range: • Incoming air temperature: -20°C to 50°C • Relative humidity: 0% to 60% Raw material/media: • Relative humidity: 45% to 55% by wieght • Requested relative humidity: 8% to 15% in the dried material Capacity: • The dual-cell, 4 m wide dryer can typically handle 2400 kg of material with a moisture content of 55% by weight in each load • The dryer is capable of drying 6000 kg raw material, with a water content of 55% to 10% in approximately one hour. SRE’s dryer is desinged in accordance with European directives. The equipment is designed to conform to the essential requirements of: • The Machinery Directive 2006/42/EC Kdodpfx Akezvq Rcepou • LVD 2006/95/EC • EMC 2004/108/EC The dryer is located in Straupe parish, Cēsis district, LV-4152, Latvia. Available for viewing on working days, 08:00 to 17:00, by prior agreement on the viewing time. The dryer is already dismantled All electrical schematics, manual, operating instructions available Upon request, we can provide a contact person with this type of working dryer for consultation Price: 35 000 EUR (VAT is not included)

Condition: used, functionality: fully functional, Performance for 6 mm diameter pellets 2.5-3 t/h We used it for about 5 years. It was purchased used but in very good condition. All bearings were replaced 1 year ago. It was working very well before it was disassembled. Kdjdsx S Ibgjpfx Akpsu A new die with rollers has been manufactured for it and is available for an additional price. For additional information, please write on Whatsapp.

Condition: like new (used), Year of construction: 2024, Pellet production plant – complete line – fully automated Salmatec press Rematec hammer mill Belt dryer VAI bagging machine Cooler Kedpozg Eudjfx Akpodu Sifter Palletizer Less than 1000 operating hours – certified Option for on-site reinstallation Option for on-site operator training

Condition: used, Year of construction: 2022, functionality: unexamined, 23 complete containerised pellet boiler houses for sale – 13 × Ba-120 (120 kW) and 10 × Pereko KSR 130 (130 kW), 2.86 MW in total. Price is per unit; volume pricing for 5+ units and for the complete lot of 23. Each unit is a self-contained mobile heat plant: boiler, burners, buffer tanks, plate heat exchanger, flue system and 12 m³ pellet silo in one insulated heavy-duty container. Crane it in, connect flow/return, heat on – no boiler room, no construction. Kdjdoz Iy Ilepfx Akpju BOILER - Ba-120: 120 kW, 70/90 °C, heats approx. 2,180 m² / 5,450 m³ - Pereko KSR 130: 130 kW, 57/95 °C, heats approx. 2,360 m² / 5,900 m³ - Both: 2 × ECOMAT 70 pellet burners (agro pellets / sunflower husk capable, up to 98 % combustion efficiency), turbulators in fire-tube heat exchanger, max. 1.5 bar, flue 300×300 mm, G3 connection, 230 V / 500 W, power modulation 90 % - EN 303-5:2012 (MSZ EN 303-5:2013) STANDARD PACKAGE (every unit) - Heat buffer: 2 × 1,000 L insulated (Hajdu PT1000) - Expansion: 3 × 200 L pressure vessels - Heat exchanger: APV / SPX TR1-MV-16I/2 plate HX, 140 kW, 10 bar - Flue: hot-gas induced-draught fan 450 m³/h / 800 Pa, vortex-tube cyclone separator (92 %), insulated acid-resistant modular chimney, draught monitoring - Fuel: 12 m³ external double-insulated pellet silo + screw feeder to internal day hopper - Ash: Ø100 mm geared ash screw to closed external bin - Controls: manual / automatic mode, control cabinet with PC, remote monitoring & fault alerts via internet, heat meter - Container: 6 × 2.5 × 2.5 m internal, PIR sandwich panels U = 0.4 W/m²K, 6 t steel floor, crane lugs, security lock, 0.9 × 2.1 m door CONDITION Pre-owned, complete, in storage since 2022. Sold as is, where is. Inspection by appointment in Hungary. Transport and recommissioning can be arranged. Ideal for schools, clinics, municipal buildings, farms, greenhouses, worker camps and emergency / temporary district heating. Full technical documentation in English and Ukrainian available on request.

Condition: used, This pellet press is being auctioned off in our industrial auction / machine auction, which includes surplus inventory, clearance sales, and individual/exhibition pieces, online. Kdjdpfs Abaqmox Akpou You can find this and many other items on our platform.

Condition: good (used), Year of construction: 2018, Equipment: documentation/manual, MAAG M-USG 600 H – PET Pelletizing Line, 6,500 kg/h – 2018 MAAG Automatik M-USG 600 H pelletizing line, manufactured in 2018, designed as an underwater strand pelletizing system for the continuous production of polymer pellets and originally used for PET. The line integrates automatic strand feeding and cutting, water cooling, hydraulic conveying, centrifugal drying and pellet classification, with an approximate nominal capacity of 5,300 kg/h and a maximum design capacity of up to 6,500 kg/h. Equipped with an 80-strand die head, automatic feeding system and strand pelletizer/cutter, hydraulic conveying system, MAAG CENTRO 1600 centrifugal dryer, exhaust fan, VIBRA Schultheis SRK 15/7.5-I-V-S vibrating screen, and control system with Siemens SIMATIC HMI. Predominantly stainless-steel construction in the areas in contact with the product and process water. Suitable for PET pellet production and potentially for recycled PET (rPET) pelletizing applications, subject to process configuration and material characteristics. Kodpjzvc R Ujfx Akpedu Two identical lines available, fitted with MAAG CENTRO 1600 dryers, machine numbers CE-0468 and CE-0469.

Condition: used, Year of construction: 2007, functionality: fully functional, power: 100 kW (135.96 HP), heating capacity: 100 kW (135.96 HP), nominal heat output: 100 kW (135.96 HP), nominal power: 100 kW (135.96 HP), tank capacity: 5,000 l, We are offering this used HDG Bavaria 100kW heating system with articulated arm discharge, manufactured in 2007. Manufacturer: HDG Bavaria Model: 100kW with articulated arm discharge Year of manufacture: 2007 If you have any questions or require further information, please feel free to send us a message or give us a call. The system is currently still in operation and can be inspected. The offer includes a 5,000L buffer tank, control unit, and various spare parts (which we have kept in stock as a precaution). Ksdpfx Ajyrhd Tekpedu

Condition: used, Year of construction: 1985, functionality: fully functional, For sale: granulator from the renowned manufacturer Buhler. Granulator model: DPAA-660 Kjdpfjw Uh Nzjx Akpedu Motor power: 160 kW – option to install a more powerful motor – 200 kW. Die diameter: 660 mm, Die working width: 160 mm, Granulator output on straw / sawdust: 2 – 2.5 t/h The granulator is currently dismantled. For a committed buyer, we will assemble it using new wear parts. Contact for more photos and details. Machine available for inspection in Sępólnie Krajeńskie, Kuyavian-Pomeranian Voivodeship, Poland.

Year of construction: 2023, operating hours: 1,500 h, condition: excellent (used), functionality: fully functional, Abstracts This is a high-quality system that mixes and homogenizes up to 3 additives in a hot mixer. The control system is included in the scope of supply. First, the material is transported from the production area to a storage silo. From this first silo, the material is fed into the hot mixer, then into the cooler, and finally into a second silo for intermediate storage. After that, there is the option to directly fill the powder onto a big bag filling scale or to compress it into pellets using a pellet press and then fill them. The steel structure is included in the scope of supply. Where necessary, the system is designed according to ATEX standards. In the Documents section, you will find a detailed English and German description of the complete scope of this system. Do not hesitate to call us to discuss and demonstrate the system. A similar system can be inspected in Europe. Main machines: • Mixaco hot mixer HM3000 - 400 kW • Mixaco cooling mixer KM9000 - 90 kW • Steel structure • AZO feeding station and gravimetric dosing for 2 solids and 1 liquid • AZO 2 special dosing scales for difficult-to-flow powders or solids • AZO 4 transport line, pressure and vacuum conveying • AZO 2 metrologically verifiable big bag filling stations • AZO control system • Kreyenborg silos ATEX 15 m³ • Kahl pelletizer 37-850 – 132 kW with box cooler and accessories The system was in operation at an R&D center in Israel. As the company now operates a production facility in Europe, the R&D center will be closed. The machines will be transported to Europe at the owner's expense and can be delivered at a port or in the production facility in Europe, EXW. Kodpeztc Nfsfx Akpjdu The details for optimal transport need to be clarified. The machine price does not include packaging.

Year of construction: 2019, condition: excellent (used), functionality: fully functional, REF: MM6372 Polar Systems Ltd bulk hopper, vibratory table, base stand, bucket elevator and diverter. Ideally suited for snack / pellet products. Manufacturer – Polar Systems Ltd. Date of manufacture – 2019. Bucket elevator dimensions - 2550mm long x 1250mm wide x 3850mm high. Kodpfxjynnlie Akpsdu Bulk hopper, vibratory table and base stand dimensions - 2550mm long x 1600mm wide x 3400mm high.

Condition: new, Year of construction: 2023, We offer this new pellet press, manufactured in 2023. Manufacturer: Artmash (Ukraine) Year of manufacture: 2023 Production capacity: 700-900 kg/hour Die: 6mm Condition: new (10 tons produced for testing) Kdedszh Hd Nspfx Akpou Spare parts included: 2 dies and rollers Category ID: 917 Type ID: 2701 Type: pellet press If you have any questions or require further information, please send us a message or call us.

Year of construction: 2025, operating hours: 2 h, condition: new, functionality: fully functional, Pelletizing plant for a wide range of materials such as wood, miscanthus, agricultural by-products and waste (hay, straw, corn stover, etc.), animal feed, and more. This is a complete compact system, built on a base frame, consisting of the following components: - Raw material storage hopper (4 m³) with agitator - Hammer mill, 22 kW drive power, for size reduction of raw materials (e.g., wood chips) Kodpoxlif Rofx Akpodu - Inclined mixer for raw material, including level sensors and fully automatic moisture dosing - Dosing hopper for pelletizing aids (e.g., corn starch) - Dosing screw for optimal material feed to the press (speed-controlled) - Pellet press with 30 kW drive power, featuring a horizontal ring die, discharge chute, temperature monitoring, overload protection, and more - Conveyor belt for pellet discharge, drop height approx. 2.5 m - Drum screen for dedusting and cooling of pellets The entire plant is centrally operated via Siemens PLC with touch display! All parameters are continuously monitored, and the plant will automatically shut down in case of malfunction! The system is designed and prepared for operation with a second press! Price excl. VAT! !!!!! Attention!! We are continuously looking for sales and service partners (worldwide) !!!!!

Condition: reconditioned (used), Year of construction: 1999, functionality: fully functional, type of input current: three-phase, power: 160 kW (217.54 HP), input voltage: 380 V, warranty duration: 12 months, year of last overhaul: 2023, Equipment: documentation/manual, 1 pellet press make: Buhler DPAB inner diameter die 660 mm tread die 138 mm Press is equipped with 1 motor 160 KW . Press door is made of Stainless steel with overload valve in door. 2 Roll press with 2 rolls on the press overhauled in dimple or racked version Press is complete with die lifting device and tools Kdjdpfxsrah Eve Akpeu The press is completely overhauled and equipped with new bearings and wear parts such as front and rear sliders die washer etc. Also new V-belts Also, all safety devices will be observed and appropriate switches on Friction protection , door switch and inspection hatches will be fitted.

Condition: reconditioned (used), functionality: fully functional, screw conveyor diameter: 27 mm, Warehouse – No. 2875 1 used compounding and granulation line, partially overhauled in 2026 and functionally tested, consisting of: Brabender gravimetric 2-component dosing system (expandable, optional at extra cost) Kdsdpjz A Sxlsfx Akpou with 1x FlexWall 40, 1x DDW-MD5, Congrav RC4 stand-alone control Twin-screw extruder Leistritz type ZSE 27 HP Co-rotating, self-cleaning, segmented screws and cylinder with intensive cooling. Screws 2x Ø 27 mm - 36 L/D with 8 cylinder zones with 3 degassing zones, 1 vacuum pump 1.5 kW Screw speed up to 1,200 rpm - adjustable Extruder drive 33.8 kW - heating power 9.8 kW installed Melt pressure sensor Control system Macromatex III MAAG Gala underwater granulation system type LPU, model SLC 5, including: Polymer start-up valve with hydraulics Die plate 20°, granulator SLC 5 with 1.5 kW drive Water box – temperature-controlled water system with Granulate centrifugal dryer type 1150, 1.5 kW drive Xantec control system Siemens Accessories: Single tempering unit for the extruder processing section The system is ready for demonstration; a test run / sample production with your material is possible on short notice. Details and dates upon request. We have other compounding extruders available ex-works: Alphatec, Coperion, Leistritz, Berstorff-Krauss Maffei, as well as all accessories: granulation systems (BKG - MAAG gala, Sikoplast, IPS, Scheer, ...), melt filters (BKG, Ettlinger, Alphatec, ...). Commissioning / training for all our systems can be carried out by our technicians; details upon request.

Year of construction: 2000, condition: reconditioned (used), functionality: fully functional, machine/vehicle number: 071, Stock no. 2806 1 used, partially overhauled, and functionally tested strand granulator Type SG-60 E Cutting rotor with single-sided bearing Rotor diameter 160 mm x width 70 mm Rotor with helical cut, 30 teeth, 2° Strand inlet width: 60 mm Up to 12 strands according to the manufacturer Kdedpjz A R Ilefx Akpju Cutting chamber with sound insulation 2.5 kW - AC drive, adjustable via frequency inverter Ready for demonstration at our plant in Wuppertal We have other strand granulators ready for demonstration. Please inquire about our current machine stock list.

Condition: excellent (used), functionality: fully functional, Year of construction: 2025, control type: NC control, degree of automation: semi-automatic, actuation type: electric, input voltage: 400 V, input frequency: 50 Hz, Equipment: documentation/manual, emergency stop, hardened rollers, Pellet press for rent – suitable for wood, plastics (PE, PET), and agricultural by-products. Available: 4 kW (50–100 kg/h) or 22 kW (200–350 kg/h). Comes with various dies for different materials. Ideal for trial runs, pilot projects, and temporary production. Flexible rental periods, delivery, and support available. 👉 Henkes Industries GmbH Ksdpsxtwyrsfx Akpsdu

Year of construction: 2026, condition: new, PLN-75 Mini Film Waste Pelletizing Line with Air Cooling The Mini Film Waste Pelletizing Line is designed for recycling low-bulk-density polymer waste at relatively low production capacities. It is a compact solution for processing film production waste and other lightweight plastic materials into reusable pellets. The system can process plastic film in either shredded or non-shredded form, depending on the type and condition of the material. Kdedpfx Aksz Nlfmopou 1. Output Range: 30~50Kg/hour 2. Standard Electricity:380V/3 Phases/50 Hz 3. Main Motor Power: 15 кW 4. Total Power: 29 кW 5. Screw Diameter. : 75 mm 6. Filter: Dual stations manual filter 7. Cooling Method: air cooled 8. Material feeder pusher: equiped 9. Application: LDPE, HDPE,LLDPE pelletizing, scraps or rolls

Condition: excellent (used), Year of construction: 2018, operating hours: 15,339 h, functionality: fully functional, machine/vehicle number: 01584, TOMCO2 DE01RB-1500 industrial dry ice pelletizer – 680 kg/hour Kdodpfjz Az Hwsx Akpju Professional TOMCO2 DE01RB-1500 Dry Ice Pelletizer, designed for industrial production of large quantities of dry ice. TOMCO2 is a well-known American manufacturer of industrial CO₂ and dry ice equipment. According to the manufacturer, these machines are developed for reliable, continuous production and can be used for, among other things, dry ice cleaning, the food industry, transportation, and other industrial applications. Technical specifications: Manufacturer: TOMCO2 Systems Model: DE01RB-1500 Machine: industrial dry ice pelletizer / extruder Production capacity: 1,500 lbs/hour / approx. 680 kg/hour Drive: hydraulic Hydraulic drive: 30 HP Electrical connection according to factory specifications: 230/460 V, 60 Hz, 3-phase Control: color touch screen / HMI Dimensions: approximately 305 × 132 × 206 cm (L × W × H) Weight: approximately 2,722 kg Designed for 24/7 production Interchangeable dies Possible pellet diameters for the 1500 series: 6, 9, 12, and 19 mm The machine can be adapted for different pellet sizes thanks to interchangeable dies. TOMCO specifies diameters of 1/4", 3/8", 1/2", and 3/4" for the 1500/3000 series, which is approximately 6, 9, 12, and 19 mm. Worldwide Shipping. Cold Jet dry ice machine for sale, dry ice machine for sale, dry ice blasting machine for sale, dry ice blasting machine for sale, dry ice blaster for sale, dry ice blasting machine for sale, industrial dry ice blaster for sale, CO2 cleaning machine for sale, Cold Jet Aero 30 for sale, Cold Jet Aero 40FP for sale, Cold Jet Aero 40HP for sale, Cold Jet Aero 75 for sale, Cold Jet Aero 75 DX for sale, Cold Jet Aero75 DX, Cold Jet 75DX, used Cold Jet machine, used dry ice blasting machine, Cold Jet Aero series, Cold Jet i3 MicroClean, Cold Jet E-CO2, Cold Jet SDI Select 60, Cold Jet IceRocket, Cold Jet Elite 20, Cold Jet Dry Icepress, Cold Jet pelletizer, dry ice blaster, dry ice cleaning machine, industrial dry ice cleaning system, pellet dry ice blaster, dry ice blasting equipment, cryogenic cleaning machine, CO2 blasting machine, carbon dioxide blaster, industrial cleaning, machine cleaning, maintenance cleaning, production line cleaning, die cleaning without disassembly, dry ice paint removal, dry ice coating removal, rust removal, fire and soot damage cleaning, electrical cabinet cleaning, food industry cleaning, automotive cleaning, printing press cleaning, dry ice blaster 20 bar, high pressure dry ice blaster, non-abrasive cleaning machine, refurbished dry ice machine, 20 ft blasting hose, dry ice blasting gun, venturi nozzle, Kärcher Ice Blaster, Kärcher IB 7/40, Kärcher IB 15/120, ASCO Jet, Cryoblaster, ICS Dry Ice, Nozzitec, Triventek, Cryonomic, Südstrahl, White Lion dry ice blaster, ICEsonic dry ice blaster, dry ice blasting machine Netherlands, dry ice machine Noordwijkerhout, industrial cleaning equipment Europe, export dry ice machine, DrDryice

Year of construction: 2022, condition: good (used), PLP MT100 Paddle coating machine Kjdpfx Ajz I Dtfjkpedu 2022, Stainless, The coating system MT is a complete machine able to mix in line pellets, kibbles, and other granulated products with additives such as liquid enzymes, fat, digest, aromas, oil, medicines, vitamins, complete with two shafts and adjustable paddles to mix and hold the product, capacity up to 50T per hour, with twin 5.5Kw motors, with heating, comes with 1500Kg buffer holding tank, infeed conveyor, paddle coater and outfeed conveyor

Condition: ready for operation (used), functionality: fully functional, 🔧 Key Features of Gala Underwater Pelletizing Systems Ksdpfx Aswm Nq Eekpodu • Die-Face Cutter: Utilizes a die-face cutter where molten polymer strands are cut directly at the die face, ensuring uniform pellet sizes tailored to customer specifications. • Centrifugal Dryer: Equipped with a centrifugal dryer that efficiently removes moisture from the pellets, eliminating the need for extended drying times. • Compact Design: The system's design eliminates the requirement for long water tanks, allowing for a more compact footprint and flexible layout in production facilities. • Ease of Operation: Designed for stable and continuous production, the system offers excellent operability, enabling a single operator to manage multiple lines effectively

Year of construction: 2011, condition: excellent (used), functionality: unexamined, machine/vehicle number: 24, For sale: Mixer – Raw material mixer from a pellet production line. Thanks to the mixer, the raw material fed into the pelletizers is homogeneous. Capacity of the line in which the mixer was used: approximately 8 tons/hour. Mixer dimensions: External length: 6150 mm, External width: 1760 mm, External height: 2740 mm, Internal length: 5000 mm, Internal width: 1490 mm, Internal height: 1750 mm, Rib diameter: approximately 1400 mm, 22 kW motor, Kdodpfxswxatbs Akpju Mixer price: 23,000 Euros, We offer a bag filter for the mixer, visible in the photos of the production line. Filter price: 7,000 Euros, The machine can be viewed in: Sępólno Krajeńskie, Kuyavian-Pomeranian Voivodeship, Poland.

Condition: refurbished (used), Year of construction: 2026, Pellet Press for Sale Manufacturer - General Dies Engine Power - 200 Kw Capacity - 2,2 t/h Year - 2014 / 2026 Reconditioned Kdjdpfxjzq E Ave Akpeu

Condition: used, Ražotājs: Munch Modelis: 420 Ražîba: 1 tonna stundā Elektrojauda: 2x75 kW Diametrs 420 mm Komplektā ar dzesētāju pēc kapitālā remonta clear Kdjdpfx Akewfqn Aepju 134 / 5,000 Translation results Translation result Manufacturer: Munch Model: 420 Production: 1 ton per hour Electric power: 2x75 kW Diameter 420 mm Complete with cooler after overhaul

Year of construction: 2014, condition: excellent (used), functionality: fully functional, RECYCLING PELLETIZING EXTRUSION LINE – BEIER 2014 / EKOCHEM – 2023 – with autostart heating Kdsdpeuac Ugjfx Akpju - Belt conveyor with amperes load control - Agglomerator – 75 kw with cooling blower and auto water spray system - Main engine extruder – 110 kw - Double degassing MELT LASER FILTER SYSTEM – HOP 400 – Ekochem – 2023 - with autostart heating - with cooling pump - laser filter spare parts: 1 set 200 microns, 1 set 250 microns, 2 sets 300 microns, 2 blades PELLETIZER – RW-440 – Ekochem – 2023 - with new Ekochem die head water pump - with PE and PP die head - with air compressor and custom die head blades – 48 h/set change - Centrifuges - Vibrator - Heated Silo + weight system - Capacity: PP( 400 – 500 kg/h) / PE( 500 – 600 kg/h )

Condition: like new (used), Year of construction: 2009, functionality: fully functional, This automatic wrapping machine is specially designed for use with dry ice slices and/or blocks. All parts in contact with the product are made of stainless steel. Automatic pitch adjustment on the conveyor, and all motors are torque-controlled. The welding temperature is displayed and electronically controlled. The control panel consists of various instruments and visual alarms and is equipped with a self-diagnostic device. TECHNICAL DATA Kdedpfx Akozxggljpeu Working speed: Up to 25 wraps per minute, 25 meters of film per minute. Product size: Max wrap width: 250mm, Max wrap height: 60mm, Wrap length: 40 to 260mm, 140 to 580mm and 200 to 800mm. Compressed air: 4 to 5 bars Version: standard version is right-hand Cold Jet dry ice machine for sale, dry ice machine for sale, dry ice blasting machine for sale, buy dry ice blasting machine, dry ice blaster for sale, dry ice blasting machine for sale, industrial dry ice blaster for sale, CO2 cleaning machine for sale, Cold Jet Aero 30 for sale, Cold Jet Aero 40FP for sale, Cold Jet Aero 40HP for sale, Cold Jet Aero 75 for sale, Cold Jet Aero 75 DX for sale, Cold Jet Aero75 DX, Cold Jet 75DX, used Cold Jet machine, second-hand dry ice blasting machine, Cold Jet Aero series, Cold Jet i3 MicroClean, Cold Jet E-CO2, Cold Jet SDI Select 60, Cold Jet IceRocket, Cold Jet Elite 20, Cold Jet Dry Icepress, Cold Jet pelletizer, dry ice blaster, dry ice cleaning machine, industrial dry ice cleaning system, pellet dry ice blaster, dry ice blasting equipment, cryogenic cleaning machine, CO2 blasting machine, carbon dioxide blaster, industrial cleaning, machine cleaning, maintenance cleaning, production line cleaning, die cleaning without disassembly, paint removal dry ice, coating removal dry ice, rust removal, fire and soot damage cleaning, electrical cabinet cleaning, food industry cleaning, automotive cleaning, printing press cleaning, dry ice blaster 20 bar, high pressure dry ice blaster, non-abrasive cleaning machine, refurbished dry ice machine, 20 ft blasting hose, dry ice blasting gun, venturi nozzle, Kärcher Ice Blaster, Kärcher IB 7/40, Kärcher IB 15/120, ASCO Jet, Cryoblaster, ICS Dry Ice, Nozzitec, Triventek, Cryonomic, Südstrahl, White Lion dry ice blaster, ICEsonic dry ice blaster, dry ice blasting machine Netherlands, dry ice machine Noordwijkerhout, industrial cleaning equipment Europe, export dry ice machine, DrDryice