Mixer / raw material agitator for pellet production

AFAU MH-8000

Condition: used, Year of construction: 2014, INDEX C200 CNC Lathe 3 Turrets Bdedpfxexxm Hfe Alcoc 2 spindles Fanuc Control: 31i-Model B Axial Motorized Switches: 6 pcs Radial Motorized Switches: 13 pcs Tool Holders: 11 pcs Boring Bar Holders: 21 pcs Pin: 1 pcs Loader Bushings + Sleeves: Ø51/Ø46/Ø41 New MBL loader bushings: 2 sets 2 optical scales overhauled by HEIDENHAIN 1 Balluff Socket Gantry Arms Box with various sensors and proximity switches and cables Motorized Belts: 6 pcs Set of anti-vibration bushings for MBL loaders Start-up time: On time: 37946 Hydraulic hours: 37,500 Production time: 26,500 With MBL Bar Feed

Condition: like new (used), The MSP 120 ZK is ideally suited for crushing and subsequent briquetting of various types of metal chips. The MSP 120 ZK briquetting press with integrated shredder is composed of a hydraulic chip press paired with an upstream shredder, both perfectly matched to each other. This system enables the crushing and compaction of chips generated during turning and milling operations. The volume is significantly reduced, and the briquettes are separated from the coolant lubricants (emulsion, oil) absorbed during earlier machining processes. The system consists of a feed hopper for loading the material to be processed and a shredder inside the hopper, which reduces chip length. A conveyor system moves the shredded chips continuously and stepwise via a conveyor belt into the chip press hopper. There, two augers feed the material into the compaction chamber. The system is equipped with a monitored liquid collection tank and pump, allowing coolants to be returned to the production process. Cycle control is managed by a PLC and an electronic level sensor for the monitoring of the hopper fill level. Optionally, a tipping device can be added for manual loading of the unit. Briquetting Press: Throughput (Aluminum): 15–20 kg/h Throughput (Steel, Copper): 45–60 kg/h Briquette diameter: 60 mm Productivity: 120–180 pcs/h Specific pressure on briquette: 1,050 kg/cm³ Motor pump power: 7 kW Total installed power: 10 kW Voltage: 400V / 50 Hz Oil tank: 80 l Dimensions: 1,400 x 1,200 x 1,050 mm Weight: 800 kg Shredder: Number of knife shafts: 1 pc Bdsdpfx Alsw R Ranococ Motor power: 5.5 kW Number of knives: 16 pcs Exchangeable knives: Yes Knife size: 25 mm Knife material: Hardened steel Shaft length: 400 mm Screen mesh size: 20 mm Hopper inner diameter: 1,000 mm Hopper volume: 1 m³ Weight: 280 kg Power supply: 380V Overall system dimensions: 2,820 x 1,862 x 2,065 mm Colour: Textured paint, RAL 7035 light grey

Condition: reconditioned (used), VK 450 The debarker has been completely refurbished Bjdpfxjq Hr N Is Alcedc

Condition: refurbished (used), FULL LINE of Drilling, max working width mm 3200, with fast automatic handling equipment. Composed of the following machines: A) LOADER (Portal) "RBO" Winner C 3200 with double pick-up and central motorized rollers table. With 2 on-ground motorized rollers ways to in-feed the piles (stacks) of panels to loader. B) TRANSFER (Connecting Rollers Table with 90° conveyoring belts) “RBO” Mod. Transfer TA 90° C) 1st Auotmatic BORER "BIESSE" Mod. Techno FDT with No. 2 Horizontal Units + No. 7 Vertical Bottom Units Bodpfedfgg Ijx Alcjdc D) 2nd Automatic BORER "BIESSE" Mod. Techno FDT with No. 2 Horizontal Units + No. 7 Vertical Bottom Units E) TRANSFER (Connecting Rollers Table with 90° conveyoring belts) “RBO” Mod. Transfer TA 90° G) UNLOADER-STACKER (Portal) "RBO" Winner SC 3200 with double pick-up, with double storage station, with central motorized rollers table. With 2 on-ground motorized rollers ways to out-feed the piles (stacks) of panels from the Unloader

Year of construction: 2013, operating hours: 84,545 h, condition: ready for operation (used), General Data Machine weight 17500 kg Bdedpfxox D Nwws Alcjc Main Drive Punching force 220 kN This TRUMPF TRUPUNCH 5000 S10 was manufactured in 2013. It features a Siemens Sinumerik 840D control system, a working area of 3050x1550 mm, and a punching press of 220 kN. Capable of handling sheet weights up to 280 kg and thicknesses up to 8 mm, it includes a Linear ATC for 21 tools and additional options like MULTITOOL and ENGRAVING. Regularly maintained and in good condition. Contact us for more information about this machine. Application Types Punching

Condition: reconditioned (used), Year of construction: 2007, operating hours: 22,605 h, functionality: fully functional, pressing force: 100 t, filling opening width: 1,100 mm, filling opening length: 1,600 mm, bale width: 1,100 mm, bale height: 1,100 mm, bale weight: 1,400 kg, overall weight: 36,000 kg, oil tank capacity: 1,300 l, year of last overhaul: 2025, For sale is a overhauled baler, with 100 tonnes pressing force, large format 1100 x 1100 mm, 75 kW drive power and 10-fold cross binding Technical data baler: Manufacturer Bollegraaf Typ HBC 110 K / 75 kW Year of construction 2007 Press power main press 100 tons Press power of pre-press 50 tons Operating hours 22,605 hours Feed channel 1,600 x 1,100 mm Capacity per cycle time 3,15 m³ Theoretic cycle time 19 sec. Bale size 1,100 x 1,100 mm Driving motor 75 kW Connected load 126 kW Bdjdpfsvf E Avox Alcoc Full load current 238 A Tying system 5-fold vertical, 5-fold horizontal, fully automated Throughput rate at a bulk weight of 30 kg/cbm approx.16 tons/h bulk weight of 50 kg/cbm approx. 25 tons/h bulk weight of 100 kg/cbm approx. 47 tons/h Bale weight up to 1400 kg, depends on material and bale lenght Volume oil tank approx. 1,300 l SPS controller Telemecanique TSX Micro Operating panel Schneider MAGELIS Touch Baler dimensions built up with hopper 11,750 x 5,000 x 7,105 mm (l x w x h) Transport dimensions only baler 11.750 x 2.500 x 3.450 mm (l x w x h) Machine weight baler approx. 36 tons Comments: The press was partially overhauled and serviced in our workshop and tested and stored after completion of the work. The machine is available at short notice and can be inspected in our warehouse by appointment. The following overhaul work was carried out: Rust removal and partial painting of the press. Remaining hydraulic oil tank drained, oil filter and air filter replaced. New hydraulic oil topped up. All hydraulic hoses replaced. Main hydraulic cylinder, two cylinders of the prepress flap and the cylinder of the press channel dismantled, disassembled, checked, cylinder tubes honed, all seal sets replaced and a final pressure test carried out. Disassembly of the prepress flap with bearings and bearing blocks. 1st and 3rd circular arc segmet cut out and a new one welded in again. Both bearings of the shaft of the prepress flap replaced. Upper material deflector on the frame of the prepress flap replaced. Press ram dismantled, checked and both front rollers replaced. Material deflectors and wear profiles on the sides and base of the press ram cut off and new ones welded in. Horizontal and vertical needle and tying unit dismantled, disassembled, checked, plastic sliding plates, bearings of the drill shafts and wire deflection rollers with bearings in the needle heads replaced. Both bronze slide rails on the left and right in the frame cover to the press ram replaced. Both wire deflection units on the left and right, with bale retaining clamps, completely renewed. Wire insertion unit including hydraulic cylinder under the needle feedthroughs completely renewed. Wire entry marks in the floor and side walls of the bale chamber welded shut and smoothed. General maintenance and service work carried out in accordance with the manufacturer's specifications. Press was tested in manual and automatic mode, accepted and stored after completion of overhaul work. We accept no liability for the technical specifications or any errors.

Year of construction: 2015, condition: as good as new (ex-display), machine/vehicle number: 2015020890, For sale is a magnetic filter system with integrated cleaning system. Filter systems of this type are usually made individually to order from customers. In this system, there is an exhibition purpose, which only served to show, and was hardly in use. product benefits Installation possible into existing production lines Bodecwghbopfx Alcsdc Separation of any ferrous metal contaminants Very corrosion resistant High wear resistance Compact design Low maintenance Technical details - 400 x 400 x 390 mm - Inlet 260x260mm - Inlet 260x260mm - 8 pcs magnetic filter rods

Condition: excellent (used), Year of construction: 2007, functionality: fully functional, turning diameter over cross slide: 710 mm, turning diameter: 710 mm, spindle motor power: 11,000 W, spindle speed (min.): 38 rpm, spindle speed (max.): 3,800 rpm, travel distance X-axis: 690 mm, travel distance Y-axis: 115 mm, travel distance Z-axis: 1,545 mm, rapid traverse X-axis: 4 m/min, rapid traverse Y-axis: 26 m/min, rapid traverse Z-axis: 40 m/min, rotational speed (max.): 6,000 rpm, type of input current: three-phase, spindle nose: JIS A2-8, overall weight: 14,000 kg, tool length: 300 mm, tool weight: 10 g, travel distance W-axis: 1,550 mm, Equipment: documentation/manual, Turn mill center OKUMA Multus B400 TECHNICAL CHARACTERISTICS: CNC control: OSP-P200L Distance between centers: 1500 [mm] Max. cutting diameter: 710 [mm] Height of centers over cariage: 710 [mm] Stroke X axis: 690 [mm] Stroke Y axis: -115 / +115 [mm] Stroke Z axis: 1545 [mm] Stroke W axis: 1550 [mm] B axis indexing precision: 0.001 [°] Milling head max. speed: 6000 [rpm] Max. milling spindle power: 11 [kW] Max. milling spindle torque: 65.7 [Nm] Coolant milling head: HSK-A63 Tool magazine capacity: 40 Max. tool length: 300 [mm] Max. tool diameter: 130 [mm] Max. weight of single tool: 10 [Kg] Rapid traverse rate X axis: 4000 [mm/min] Rapid traverse rate Z axis: 40000 [mm/min] Rapid traverse rate Y axis: 26000 [mm/min] Rapid traverse rate W axis: 12000 [mm/min] Spindle nose: JIS A2-8 Min. spindle speed: 38 [rpm] Max. spindle speed: 3800 [rpm] Increment C-axis: 0.001 [°] Supply voltage: 400 [V] Bsdeyqx Rzjpfx Alcodc Weight: 14000 [Kg] INCLUDED EQUIPMENT: 1 × One-Touch IGF software option 1 × ATLING 2-point steady rest, type AX8I-NAOS (Ø85–360 mm) 1 × SMW AUTOBLOK 3-jaw chuck Ø340 mm, type KNCS-N-340-117 1 × Chuck clamping pressure regulator 1 × Parts catcher 1 × NC tailstock 1 × MARPOSS T18 tool probe 1 × Remote electronic handwheel 40 × HSK-63 tool holders 1 × 2-color status signal lamp 1 × Chip conveyor 1 × Coolant tank 1 × Transformer 1 × Complete set of manuals + OKUMA CD Machine visible under power in our premises by appointment. Price on request, loading on truck included. Possibility of shipping Worldwide. The information on this page has been obtained by the best of our ability. Therefore, its accuracy can not be guaranteed. Machine similar to brands such as Mazak, DMG Mori, Index Traub, Doosan, Hermle, Chiron, and Biglia. Also includes lathes, mill-turn machines, and milling machines.

Year of construction: 1999, condition: good (used), Built in: 1999 Capacity (A4 stacks packaged): max 20 - 24 Pakete/min Capacity ( A4 stacks loose): max 16 - 20 Pakete/min Bdedpfedym Srox Alcjc Pallet height (incl. pallet): max 1.600 mm Pallet size : max 1.200 - 1.200 mm Size: max 420 x 307 x 320 mm Size: 148 x 110 x 50 mm Equipment: • infeed and buffer section • turntable • infeed table • automatic palletizer • roller track for full pallets • intermediate cardboard slip sheet hopper • pallet dispenser

Condition: excellent (used), Year of construction: 2008, operating hours: 9,000 h, laser power: 4,400 W, Used very clean Bystronic Bystar 3015 4.4kW for sale / flat bed industrial cnc laser for sale Bystronic ByStar 3015 4.4kW BRAND: BYSTRONIC YEAR: 2008 Bdodpfx Aer Hcmrjlcoc MODEL: ByStar 3015 APPLICATION TYPE: LASER CUTTING LOCATION: UNITED KINGDOM MACHINE TYPE: LASER CUTTING MACHINES (CO2) Fully Serviced and Well Maintained CONTROL UNIT BRAND: BYSTRONIC Technical Information BRAND: BYSTRONIC LASERPOWER: 4.4KW / 4400 watts LASER TYPE: CO2 LASER BRAND: BYLASER 4400 MOVEMENT X-AXIS MOVEMENT: 3000 MM Y-AXIS MOVEMENT: 1500 MM Machines hours: Cut hours: 9,000 ADDITIONAL EQUIPMENT – BYPOS – CUT-CONTROL – 2 CUTTING HEADS (5″, 7.5″)