Used Bending Flange for sale (4,759)

Year of construction: 1973, condition: like new (used), Used BRONX Heavy Duty Initial Pinch Pyramid bending rolls. Year of manufacture : 1973. MACHINE FORMERLY INSTALLED AT ROLLS ROYCE PLC IN DERBY UK. IMMEDIATELY FOR SALE AND NOW LOCATED IN BELGUIM WHERE IT CAN BE INSPECTED. SPECIFICATION CAPACITY Two sets of dimensions which are shown below as "Prebending & Rolling" and then "Rolling only". Material Mild Steel Mild Steel Tensile strength 28/32 tons/sq.in 28/32 tons/sq.in Maximum width 11’(3350mm) 11’(3350mm) Maximum thickness at this width 2” (50mm) 2½” (63.5mm) Minimum inside diameter of rolled cylinder at maximum capacity 30’ (762mm) 37 ½’ (953mm) Maximum thickness of plate when hot rolling (finished rolling temperature 850° C.) 4” (102mm) 5” (127mm) Minimum inside diameter of rolled cylinder at maximum capacity hot rolling 40” (1016mm) 50” (1270mm) MAIN PARTICULARS Diameter of all rolls - 27” (686mm) Gjdpfxsh U Rzgo Ai Njuc Body length of rolls - 11’2”(3403mm) Rolling speed - 12 f.p.m. (3600mm/min) Main drive motor - 150 H.P. Slip Ring Type Two bottom roll adjusting motors, each - 50 H.P. Slip Ring Type Combined operation of swing down bearing and top roll counterbalance - Hydraulically applied Hydraulic power pack motor - 10 H.P. Electrical equipment to be suitable for operation on a supply of - 400/440 volts, 3 phase, 50 cycles CONE ROLLING ATTACHMENT: To facilitate the rolling of taper or conical forms, a skid plate is fitted to the inside of the non-drive end housing. ELECTRICAL EQUIPMENT Motors: Main Drive - 150 H.P. half hour rated – slip ring screen protected – foot mounted type. Bottom Roll Adjustments - 50 H.P. half hour rated – slip ring screen protected – foot mounted type. Hydraulic Power Pack Motor - 10 H.P. continuously rated – Squirrel cage – screen protected – foot mounted type. Control Gear: Main Drive - Drum type reversing control gear with 5 minute rated wire wound resistances, designed to pass 100% full load on the first notch or operating position in each direction. The controller will be fitted with off position interlock and limit switch rings where necessary. Bottom Roll Adjustments - Drum type reversing control gear with 5 minute rated wire wound resistances designed to pass 100% full load on the first notch or operating position in each direction. The controllers will be fitted with off position interlock and limit switch rings where necessary. Hydraulic Power Pack - Direct-on-line contactor type starter, operated from a maintaining type push button station. Solenoid valves for operating cylinders are push button operated. Note: Full protection to be provided for all the above control gear by a circuit breaker, incorporating overload and no-volt protection. FEATURES AND EQUIPMENT Spare Roll included with the machine. LENGTH TBA MM WIDTH TBA MM HEIGHT TBA MM WEIGHT 95 tonnes NOTE: The information contained herein is provided in good faith, but however due to unforeseen errors or omissions cannot be binding as to accuracy.

Year of construction: 2024, condition: new, MRB-S Series Technical data (see pictures) Standard equipment CE Conical bend Motorized back roller Additional control panel for upper and lower rollers which are operated with landing gear. SAE 1050 steel rollers Induction hardened rollers, Relaxed steel construction, at 2.5 and 3m Machine supports, brake system for precise bends, Digital display. Motorized back roller with puller Optional equipment Motorised under-roller mounting, ground rollers Extended rolls for profile bends, Special rollers for profile bending, Special packaging for international deliveries. MRB series: Technical data (see pictures) Standard equipment CE standard Digital display Guodpfx Aijfin E Ds Nec Conical bend Motorized back roller with tightening Additional control panel for upper and lower rollers, which are operated with landing gear. operated by landing gear. SAE 1050 steel rollers, Induction hardened rollers, Relaxed steel construction, Braking system for precise bends. Optional equipment Motorized bottom roller with suit, stone rollers Extended rolls for profile bends, special rollers for profile bending, Special packaging for international Programmes Everything is configurable on demand, very short production & delivery time. We will be happy to provide you with further information on request. Durma Maschinen GmbH is part of the internationally successful Durmazlar Group, which exports new, high-quality sheet metal working machines all over the world and is headquartered in Türk

Year of construction: 2024, condition: new, Bending capacity: 6 mm Bending: 5 mm Bending capacity: 6 mm Bending: 5 mm Bending length: 2,030 mm roller diameter: 170 mm Engine power: 4 kW Length: 3.600 mm Width: 1,020 mm Height: 1.120 mm Weight: 2.400 kg The machine can be viewed and demonstrated at any time by appointment in our demonstration centre in Staufenberg. Gsdpfxoftdh Is Ai Neuc Further machines are ready for demonstration at our premises in Staufenberg. We will be happy to provide you with further information on request.

Year of construction: 2024, operating hours: 32 h, condition: new, Make: DURMA Type: AD-S 30175 Year of construction: 2020* bending length: 3050 mm Press force: 1750 kN Control: DELEM DA-66T Operating hours: 32 h Controlled axes Backgauge: X,R,Z1,Z2,+Delta X +/- 125 mm CNC controlled passage between the uprights: 2600 mm stroke length: 265 mm Installation height: 530 mm table width: 104 mm table height: 900 mm Stands projection: 410 mm travel range X-axis: 650 mm traverse speed X-axis: 500 mm/s travel range R-axis: 250 mm infeed speed: 160 mm/s folding speed: 10 mm/s Retraction speed: 100 mm/s Dimensions L/W/H: approx. 4250x1700x2750 mm Weight: approx. 11500 kg Standard equipment Y1,Y2,X,R - X=650 mm Control: CNC Cybelec ModEva 19T - PC 1200 3D SW D-BEND 3D CAD/CAM import & simulation program CNC controlled motor-driven crowning European tool clamping system 60 mm die holder (only for European die system) Throat 410 mm 2 support arms movable from the front with T-slot and tilt stop Backgauge system: Siemens DC Servo motorized with linear guide and ball screw Protective covers CE Marking Extended equipment Safety system CE standard for EU: FIESSLER AKAS-3P motorised+FPSC (SAFETY PLC) Controlled axes Backgauge: X,R,Z1,Z2,+Delta X +/- 125 mm CNC controlled Guedsdx Nlujpfx Ai Njc Control: DELEM DA-66T Hydraulic top tool clamping Wila NSCL-II-HC/UPB - PREMIUM - 250 t/m Hydraulic bottom tool clamping Wila NSCR-II-HC-CNC/UPB - PREMIUM - 300 t/m Powerpack for hydraulic clamping AP3-AP4 Bending aid -

Year of construction: 2024, condition: new, Control unit - with NC control Conical bending device Side roll positioning electronically synchronized via PLC Safety mechanism for welding (welding possibility) on the machine Machine body made of stress-relieved annealed steel 4 roll drive system - upper, and lower roller with hydraulic motor driven synchronized via planetary gear (ᐳ 430 mm) Electrical and hydraulic protection against overloads Hydraulically adjustable lower roller pressure Hydraulic roller brake, prevents the sheet from slipping back Hydraulic swinging out of the upper roller bearing, for easy removal of the formed sheet Safety wire Induction-hardened rollers (HRC 54), crowned ("crowning"). Variable speed Bending length: 2050 mm Bending capacity: 13 mm (d x 5) Bending capacity: 10 mm (d x 1.5) Top roll: 230 mm Bottom roll: 210 mm Maximum roll width: 30 mm Length: 3830 mm Width: 1160 mm Height: 1200 mm Motor power: 11 kW Weight: 4700 kg Guodpfx Asdzzyfoi Njc

Condition: new, Year of construction: 2026, functionality: fully functional, Equipment: CE marking, Entry-level model panel bender bending center For detailed information and a personalized quote, please send us your inquiry. We will process it as quickly as possible and get in touch with you. Gujdpfx Aisy H Huho Nsc

Condition: used, 12-piece die block for GEWA press brake Bending tool for press brake, lower tool Type: 0255/14 V-block size: 16 mm for 90° V-block angle: 88° Die depth: approx. 8 mm Gujdpfewbvmijx Ai Njc Height: 120 mm Max. pressure per meter: 100 t/m Die base width: 60 mm Total length: 4175 mm Segment lengths: 4 x 835 mm, 1 x 400 mm, 1 x 200 mm, 1 x 100 mm, 1 x 50 mm, 1 x 40 mm, 1 x 20 mm, 1 x 15 mm, 1 x 10 mm Weight: 110 kg Very good condition

Condition: used, Pedrazzoli UNIVERSAL BROWN 42 CN 1 axis pipe bender. Max bending capacity: mm 42×2.5. Minimum internal radius of bending : mm 22. Max average radius of bending operating with rollers : mm 260. Max angle of bending: 185°. Max length of tube to be bent : mm 3100. Installed power : Kw 5.5. Dimensions : mm 4700x800x1300. Gsdpfxsqgd Eko Ai Njuc Weight : Kg 1100.

Condition: new, Synchronized hydraulic bending press MVD Ready in stock except when sold! Mod. I Bend D 4100/320 Videographic Numerical Control ESA W660 color Controlled axes Nr. 7 ( Y1-Y2-X-R-Z1-Z2-X5) WILA motorized compensation table Multi beam barriers NEW ELECTRONIC DSP LASER UNIMEC high speed motorized rear register (Made in Italy) GIVI MISURE optical scales (Made in Italy) Bending length mm 4100 Exercised power Ton 320 Hollow mm 510 Stroke mm 410 Gedofh N Agepfx Ai Nsuc Opening mm 635 Upper tools and lower die ROLLERS supplied

Condition: new, MVD Synchronized Hydraulic Bending Press Ready in stock unless sold out! Mod. I-Bend D 3100/320 Color Videographic Numerical Control ESA S875 W *dxf Controlled axes No. 8 ( Y1-Y2-X-R-Z1-Z2-X5_A1) WILA motorized compensation table Multi-beam barriers NEW ELECTRONICS DSP LASER UNIMEC high-speed motorized rear register (Made in Italy) GIVI MISURE optical scales (Made in Italy) Bending length mm 3100 Power exerted Ton 320 Recess mm 510 Stroke mm 410 Opening mm 635 Guedpfx Aierqvtms Nsc Upper tools and lower die ROLLERS supplied

Condition: excellent (used), functionality: fully functional, actuation type: mechanical, number of rollers: 3, overall weight: 5,000 kg, Equipment: documentation/manual, Profile Bending Machine PARMIGIANI Mod. MERCORI – M. Used. Three-roll horizontal profile bending machine. Immediately available while stocks last. Visualized adjustment control. Supplied complete with tooling for bending flat bars and tubes. New electrical cabinet. User and maintenance manual included. Bending capacity: angle 120 x 120 x 12: min. Ø 1200 mm; U 160 vertical: min. Ø 1000 mm; Flat bar vertical 140 x 40: min. Ø 1000 mm; Flat bar horizontal 120 x 30: min. Ø 1600 mm; Tube 4″: min. Ø 1200 mm. Weight: 5000 kg. Motor power: 380 V, 12 Hp. Gujdpfoyxwdwox Ai Njc

Condition: used, Year of construction: 2004, Technical details: tube diameter: 20 mm bending radius max.: 100 mm control for program: S7-300 tube pipe draw up length: 2270 mm air pressure - required: 7 bar total power requirement: 15 kW Bending speed: 540 °/sec control voltage: 24 V / DC V connection voltage: 400V / 50Hz / 3 Ph V dimensions L x W x H: Biegeaggregat: 1,8 x 1,4 x 1,6 m dimensions L x W x H: Zuführung: 1,2 x 1,5 x 1,55 m dimension machine xH: 3,0 x 1,0 x 1,2 m Mandrel tube bending machine Bending direction RIGHT Operation via SIMANTIC Panel PC control unit Pneumatics: Pressure 7 bar; flow rate 200 l/min. Gujdpfx Aeu Ibzkei Nsc Hydraulics: Pressure 150 bar; flow rate 6.8 l/min. Equipment/Accessories: -oil drip tray 3.1 x 0.96 x 0.02m -Spare parts and accessories *

Condition: used, Year of construction: 1990, Technical details: tube diameter: 42 mm wall strength: 25 mm round bar steel: max. Ø 20 mm square material: Rohr 25 x 25 mm bending radius max.: innen max: Ø 20 und außen max: Ø 170 mm bending speed: keine Angaben °/s tube pipe draw up length: 3000 mm control: Software RC 7000 weight of the machine ca.: 2,8 t dimensions electric cabinet: 800 x 700 x 2000 mm dimension machine xH: 5,1 x 0,7 x 2,0 m Application: Machining of deformable tubes, rectangular tubes and round bars and square tubes. Description of the software RC7000, programming manual rectangular tube 42 x 20 x 2,5mm bending direction to the left Gujdpfx Aieu Ibvuo Nec Operation via control panel with monitor Accessories: -div. bending tools for tube Ø 25mm -12 div. collets -div. auxiliary and clamping devices *

Condition: used, Technical details: sheet width: 1080 mm plate thickness: 1,25 mm distance between columns: 1200 mm dimensions LxWxH: 1,9 x 0,6 x 0,9 m Gusdpfeu Icdyex Ai Noc weitere Merkmale: 2x Biegewalzen: -Ø 63 x 1080mm -die Oberwalze ist ausschwenkbar -die Unterwalze hat einen Verstellweg von 12mm -Antrieb manuell über Handkurbel 1x Laufwalze: -Ø 63 x 1080mm -mitlaufend -Verstellweg ca. 5mm *

Condition: used, Year of construction: 1992, Technical details: tube diameter: 6 mm tube diameter max.: 16 mm bending angle max.: 90 ° electrics - voltage/frequency: 220 / 50 V/Hz Total power requirement: 0,75 kW Weight approx.: 0,145 t machine dimensions LxWxH: ca. 1,0 x 0,8 x 1,2 m Application: Mini tube bending machine with free bending head. Processing of precision steel tubes according to DIN 2391/C, material 35.4 NBK Ø 6 - 16mm. -With hydraulic drive -8-fold bending preselection angle up to 180 -Pipe stop length 1m -Emergency stop button -mobile with parking brake Gjdpfx Aiowivn No Njuc -pivoting pipe head (vertical in horizontal position) -required hydraulic oil = approx. 20 liters (e.g. Esso Nuto 32) Accessories: various bending tools *

Condition: used, Technical details: tube diameter: siehe o mm wall strength: siehe o mm voltage: 230 V / 1Phase V total power requirement: 0,55 kW machine weight approx.: 56 kg dimensions L x W x H: 0,45 x 0,37 x 0,35 m HYDRAULIC LINE PRESETTING DEVICE for EO pipes Gusdpfeu Icu Ssx Ai Noc Application for crimping flared fittings on hydraulic lines. Crimping of common raw materials such as steel (ST 35.4 NBK and-or ST 37.4 NBK and-or ST 52.4 NBK), stainless steel (1.4571/1.4541/316Ti or similar) and copper pressure-controlled There is a flaring tool for the size Ø 14mm on the machine. The operating pressure is variably adjustable. *

Condition: used, Technical details: bending angle max.: 180 ° working height: 350-550 mm operating voltage: 380 V revolutions per minute: 10-20 U/min number of bars max.: 1-4 mm total power requirement: 1,3/2,1 kW Weight approx.: 690 kg dimension machine xH: 1,2 x 0,87 x 1,2 m -Two plate speeds -Mode selector switch for automatic mode, jog mode, continuous operation -Four continuously adjustable counterholder bars without accessories! Gedpfxsxu Dxqe Ai Nouc *

Condition: used, Year of construction: 1997, Technical details: tube diameter: 4,75 - 8,0 mm wall strength: - mm bending radius min.: unterschiedlich, various, variada mm bending angle max.: 180 ° compressed air: min 4,5 bar Total power requirement: ca. 10 kW Weight approx.: 6,0 t dimension machine xH: 6,3x3,7x2,0 m dimensions electric cabinet: 1,8x0,5x2,7 m dimension control panel: 0,85x0,68x1,65 m fully automatic numeric control for bending of hydraulic supply pipes, car brake pipes various length - various numbers of bending possible (max. 100 bendings per pipe) - 2 independent bending module, every modul has 2 NC axis with functions: " longitudinal process (axis 1 and 3) and " turning of bending head" and bending (axis 2 & 4) - program memory for 250 pipes (lines) - the feeding unit consits of manual a manually filled drum magazine (drum magazine pipe dia.=4,75mm up to dia=8,0mm with 500/1000 pcs) - load swiveling arm - control panel Bundy GHF 60134 Gujdpeu Ibukofx Ai Nec accessories: - div. single and add-on parts *

Condition: used, Year of construction: 2006, Technical details: bending angle max.: 75 ° working height: 850 mm operating voltage: 380 V Weight approx.: 1,0 t dimension machine xH: 1,9 x 2,6 x 1,0 m transport measurements machine: 2,6 x 1,8 x 1,0 m Single bending and double bending of reinforcing steel possible. Number of bending forms = 2 pieces Bending angle 40°; 60°; 75°. bar size: angle form=Ø 12 - 50mm and double angle=Ø 12 - 35mm Operation via control panel with touch screen bending plate: -Ø 480mm -speed= 7,5 / 15 rpm. -bending pin bore= Ø 48mm (16 pieces) -center pin=Ø 50 x 94mm Counterholder bars: -2piece length=840mm -Displacement per handrail 100mm -13 holes of size Ø 48mm Accessories: bending attachments 2x Ø 60mm; 2x Ø 78mm; 1x 96mm; 1x Ø 122mm; 1x Ø 160mm; 1x Ø 200mm Gedpfxou Ibu Ro Ai Nouc 1x pin for plate 8x counterholder div. shapes 1x bending trough *

Condition: used, Year of construction: 1993, Technical details: tube diameter: 80 mm tube diameter min.: 6 mm control for program: Gelma MM-1 Godpfx Aou Ibyyoi Nouc tube pipe draw up length: 1800 mm weight of the machine ca.: 0,232 t dimension machine xH: 1,9 x 0,7 x 1,3 m Semi-automatic PIPE BENDING MACHINE Operating modes are manual but also semi-automatic Application: for multiple bending of pipes The swivel unit with bending preselection for 3 different bending angles in single and automatic mode. The machine is currently equipped with a stop bar for tube size Ø 10mm for 6 angle settings. The bending machine is movable/adjustable. Equipment/accessories: 6 cam rods/stop rods 6 control disks Bending tool for Ø 12mm *

Condition: new, Year of construction: 2026, shaft diameter: 50 mm, - Shaft diameter 50 mm - Rotates clockwise and counterclockwise Gedpfx Aowv Ufaji Njuc - Suitable for horizontal/vertical use - Foot control - Emergency stop - Documentation - 400V

Condition: new, Year of construction: 2026, - Capacity 700 x 4 mm Oxbmp - Electrically adjustable rear roller - Digital display - Hardened rollers - 2 speeds - Conical roller - Rotating upper roller - Brake motor Guodpfoh Rbvgox Ai Nsc - Foot switch - Emergency stop - Documentation - 400V

Condition: new, Year of construction: 2026, number of rollers: 3, - Capacity: 700 x 4 mm - Conical rollers - Removable upper roller - Brake motor - Foot control - Emergency stop - Documentation Godpfx Aish Raytj Neuc - 400V

Condition: used, CNC press brake FASTI type 904-125/30 serial no. 95-904-5775 year of construction 1995 Pressure capacity 125 ton. Working length 3050 mm Stroke approx. 335 mm Stand projection 300 mm Clearance between the side uprights 2550 mm Tool installation height max. 465 mm (opening width between the tool holders) Table width 90 mm (the clamping system is mounted on the table) Table height above floor 875 mm (910 mm with clamping system) Backgauge X-axis 500 mm Backgauge R-axis 115 mm Backgauge Z-axis approx. 1950 mm Lowering speed Y rapid traverse 90 mm/s Lowering speed Y-operation 8.9 mm/s Return stroke speed Y-retraction 75 mm/s Oil filling approx. 160 liters Motor power 18.5 kW Mains connection 400 Volt, 50 Hz, 20 Amp. - 7-axis CNC control DELEM type DA 58 with LCD screen - 1 axis for back gauge - stop depth (X-axis) - 2 axes for back gauge - fence height (finger R1 + finger R2) - 2 axes for back gauge - stop finger, laterally movable (finger Z1 + finger Z2) - 2 axes for press beam with servo valves and measuring system Y1 and Y2 - Operation via electric foot switch and 2-hand control panel or 2-hand control panel only - Hydraulic tool clamping for the TRUMPF upper tool system, with 20 mm clamping groove Gusdpfshmmfkox Ai Nsc - Hydraulic tool clamping for the lower tool with 13 mm table groove, depth 21 mm (tool pin 13 x 20 mm) - FIESSLER safety light barrier, type AKAS - 2 material support arms at the front, manually movable to the side and height-adjustable - Electrical diagram, hydraulic diagram, user manual for control available - Control cabinet on the machine - without tools Space requirement L x W x H 5000 x 2500 x 3050 mm Transport dimensions L x W x H 5200 x 1900 x 2950 mm Weight 8.5 tons. Good condition

Condition: used, Semi-automatic tube bending machine, mandrel tube bender MOBITEC type BAH 1-2 KOTTMANN und BERGER GmbH Serial No. Year of construction for simultaneous bending of two steel tube sections up to Ø 12 mm Guodpfxjpu R Nvo Ai Njc Bending angle max. 90° Tube diameter max. 12 mm Mandrel length approx. 65 mm Rated power 3.5 kW Compressed air max. 6 bar / approx. 1 litre per bending cycle Power supply 400 Volt, 50 Hz - Pneumatic clamping - Pneumatic mandrel retraction - Angle input control via STÖBER Controlbox Series 4000/5000 - SIEMENS S7-200 control with TD200 display - Machine without bending tools and without tool storage pins 25 x 183 mm - Only 1 bending mandrel available (see pictures). Required space (L x W x H) 1000 x 1000 x 1500 mm Weight 390 kg Good condition