Used Adhesive for sale (688)

Condition: used, Veneer machine with direct stacking Manufacturer: Fischer & Rückle Type: FZR15 / DAR 12 Year of manufacture: 2006 / 2014 Cross-feeding splicer For highly efficient cross-gluing of parallel-joined veneer strips into endless or component-specific veneer surfaces. The cut or rotary-cut veneers must be pre-glued with PVAc or urea adhesives. This cross-gluer is the most economical alternative to longitudinal gluers for cross-grain applications. Production Approx. 17-20 joining points/min Technical data Veneer strip length (grain direction): 350-1500 mm Veneer strip width (cross-grain direction): 50-500 mm Veneer strip thickness: 0.3-1.5 mm Equipment Feed device for efficient and convenient semi-automatic feeding of veneer strips. Plate automation for component-specific surfaces with pre-sorted components and a pre-selected number of veneer strips. Features - Perfect bonding of cut or rotary-cut veneer of all wood species, even with wavy or rippled veneer - Unique, tried-and-tested horizontal pressing system that results in fully closed, solid glue joints - Solid, robust construction for high durability, reliable and fail-safe operation - Easy operation thanks to screen, clear symbols, separate manometer with direct access, etc. - Liftable pressure bars for quick and easy access to the heating plates for cleaning - Few wear parts, low costs for service and maintenance Cross cutter For cutting to a pre-set format width (across the grain). The width is determined by two photoelectric cells that are mounted at the required distance from the cutter. Direct stacking device DAR-22 For outputting and stacking the veneer surface directly after splicing. The spliced surfaces are gently outputted and stacked on this compact direct stacking device without mechanical intervention. Min. veneer sheet length (grain direction): 350 mm Veneer sheet width (across the grain): 250 - 1200 mm Max. stack height approx. (small sheets are not perfectly aligned): 500 mm Max. stack width (across the grain) for discharge to the rear end: 1200 mm Note: Gedpfx Aszuz Hfobisbw The technical data and descriptions are a transcript of the original order confirmation. Data is for informational purposes only and is not binding.

Condition: used, Year of construction: 2008, Single-sided edge banding machine Manufacturer: HOMAG Type: Optimat KAL210/6/A20/S2 Year of manufacture: 2008 Single-sided machine for joint milling of straight workpiece edges, edge banding and finishing of various edge materials from rolls or as strips, up to 20 mm edge thickness, in longitudinal and transverse operation. power control PC22 Modern control system based on Windows PC Technical data - Feed rate 18 - 25 m/min. - Feed rate with profile milling cutters FK11 max. 20 m/min. - Workpiece thickness 8 - 60 mm - Edge material strips max. 0.4 - 20 mm - Edge material rolls 0.3 - 3 mm Joint milling unit - 2 motors, each 3 kW, 150 Hz, 9,000 rpm. for joint milling of the workpiece edge before edge banding - electropneumatic control of both motors Gluing unit A20 - 2 rollers Quickmelt hot melt adhesive unit - Temperature control electronically with LED display Gbedpfx Abozux R Ioisw Magazine for 1 roll, manual - for solid edges, strips and rolls - 1 edge feed - 1 roll holder Pressure zone C - 1 driven pre-pressing roller, diameter 150 mm - 6 after-pressing rollers, diameter 70 mm Trimming unit HL84 / 0.8 kW - 2 motors, each 0.8 kW, 200 Hz, 12,000 rpm. - Motors can be manually swiveled for chamfer trimming Pre-milling unit 1.5 kW - 2 motors arranged one above the other, each 1.5 kW, 200 Hz, 12,000 rpm. Profile milling unit FK11, manual - For processing the edge overhang on the top and bottom edges of the workpiece and for milling the front and rear edges of the workpiece Belt sanding unit KS 10 - for sanding straight and solid wood edges, oscillating, sanding pressure manually adjustable Profile sanding unit PS 10 - sanding from below, for sanding profiles, sanding pressure manually adjustable Automation package Chamfer / Radius KAL210/6/A20 - Automatic adjustment of the infeed fence - Automatic adjustment of the pressure zone - Pneumatic adjustment from chamfer to straight trimming - Pneumatic adjustment of the trimming motors for flush or overhang trimming - Pneumatic adjustment of the pre-milling unit for flush or overhang milling - Automatic adjustment from chamfer to radius milling during profile milling - Pneumatic adjustment PN10 / FA11 - Electronic height adjustment

Condition: used, Year of construction: 2007, operating hours: 10,000 h, machine/vehicle number: ET212, Used Labeling Machine PE LABELERS Universal Master up to 7500 bph The Machine delivers advanced technology for labeling glass bottles, meeting production demands of up to 7500 bottles per hour. Furthermore, P.E. Labellers manufactured this machine in 2007, ensuring precise operations with its robust design and integrated features. Technical specifications and performance of the Used PE Labellers Labeling Machine The labeller includes eight rotating plates and five labeling stations. Specifically, three stations apply adhesive labels, while two use cold glue. The machine rotates clockwise, which streamlines bottle flow management. Additionally, its manual adjustment system for both the head and labels enables quick adaptations to different formats, thereby enhancing flexibility. Production capacity and configuration The labeller handles glass bottles with a maximum diameter of 120 cm and a standard 0.75-liter format. Consequently, it operates at a top speed of 7500 bottles per hour, making it ideal for medium-scale production lines. Moreover, the system applies labels to the front, back, and neck of each bottle, ensuring a high-quality, professional finish. Labeling method and management in the Used PE Labellers Labeling Machine This machine applies labels using adhesive and cold glue methods. Therefore, this dual approach ensures compatibility with a wide range of label designs and materials. Meanwhile, operators manually adjust the system to maintain precise control during each production batch. Current state and operational specifications Gbjdpevgu Udofx Abiow The machine remains in storage; however, it is ready for immediate deployment. It has recorded 10,000 working hours, yet it still offers substantial operational capacity. Furthermore, its robust build, weighing 2250 kg, ensures stability and durability even under high-speed conditions. Electrical data and power requirements The labeller PE LABELERS Universal Master up to 7500 bph runs on 400 V, with an installed power of 5 kW and a frequency of 50 Hz. As a result, its electrical configuration meets industrial standards, ensuring efficient energy usage for extended operations. Additionally, its energy efficiency supports long-term cost savings. Applications and technical advantages The Used Labeling Machine PE LABELERS Universal Master up to 7500 bph ensures efficient and accurate label placement. Similarly, its versatile labeling stations handle bottles of various shapes and sizes without compromising output quality. Consequently, this versatility makes it a reliable option for many bottling operations. Technicians and industry experts rely on this machine for its performance and customizable configurations. Above all, it represents an excellent choice for demanding bottling applications.

Condition: new, Box Erectors Igluetech/Brunel Engineering Services RSE Manufacturer/Brand: Viioni Model: Box Erector 5 Controller: Unitronics Jazz Pneumatic System: Yes Adhesive System: Hot melt adhesive Safety Devices: Yes Emergency Stop: Emergency Stop Control Cabinet/System – Brunel Engineering Services Ltd: Manufacturer: Brunel Engineering Services Ltd Model No.: RSE Serial No.: RSE-007 Voltage: 230 V Frequency: 50 Hz Current: 16 A Marking: CE/UKCA Godpfovu Sriex Abijbw LUES Hotmelt Systems Adhesive Unit: Manufacturer: LUES Hotmelt Systems Type: 020142 Serial No.: pM 0865-00 SE Year of Manufacture: 12/2021 Voltage: 400 V Frequency: 50/60 Hz Power: 2.1 kW System: Hot melt adhesive process Temperature Control: Electronic Connections: 2 hoses / 2 adhesive guns 4 pieces Price per piece

Condition: used, functionality: fully functional, This listing is for a second-hand ‘Canon Perfekt Binder -E1’ adhesive binder Item for sale: 1x Canon Perfekt Binder -E1: We also have other finishing options and printing presses in stock. Please feel free to contact us! Condition: Gbsdpjywulcsfx Abisw This listing is for a used machine, which may show signs of wear (minor scratches or discolouration). The machine has been tested and is in working order Packaging and shipping: You are welcome to view the machine during our business hours. Please arrange an appointment! Seaworthy packaging and worldwide shipping available on request! For further information, please feel free to contact us directly.

Condition: new, neu ca. 2 - 4 Wochen ab Auftr 929 € 16 mm Starter set for anyone who wants to work professionally and efficiently contains the most important tools as basic equipment. Consisting of: 4 pieces screw clamp 180° HIS16Z3000 4 pieces stop bracket 90x37.5mm HIS16WA9037 4 pieces stop bracket 90x90mm HIS16WA9090 4 pieces stop bar 115mm HIS16FA11512 pieces quick clamping bolt short HIS16SB100 1 piece cleaning brush HIS16RB 1 piece torch holder HIS16BH 1 piece cleaner HIS-Cleaner-1L Gjdsyq Sp Rjpfx Abisbw 1 piece anti-adhesive agent HIS-Premium-1L OPTION: Tool trolley HIS16WW1000 € 449,--

Condition: new, axle configuration: 2 axles, suspension: air, tire size: 245/70-17,5, Equipment: ABS, - EBS - LED lighting - Alloy wheels - Air suspension - Spare wheel - Tool box - Central lubrication system - Additional steering axle Reference: 0-318 Godpfx Abeyr Izxjijbw PAVIC 2-axle forestry machine lowboy trailer, type: STLT2Z for harvester transport – in progress! Color can be chosen freely!!!! Fifth wheel load: 18,000 kg Aggregate load: 24,000 kg (technical) Total weight: 42,000 kg (technical) Unladen weight: 9,300 kg Made in Germany!!!! Chassis as a steel welded structure made of high-quality fine-grain steels Lashing eyes 130KN per side, 5 pieces Additional lashing eyes, 3 pairs on the upper bed Steel stake system, galvanized with aluminum sideboards (silver anodized) Steel front wall, approx. 400mm high Folding aluminum ramps with mechanical locking Central lubrication system SKF with reservoir (brake light-controlled) with approx. 20 lubrication points Dimensions: Overall length: 16,000 mm Bed length including rear area: 11,364 mm Fifth wheel height: 1330 mm Ground clearance in driving position: 184 mm Fifth wheel dimension: 600 mm R1 dimension from kingpin to the front: 410 mm (turning radius) R2 dimension: from kingpin to the frame: 2150 mm (turning radius) Further dimensions can be requested from us (technical drawing) Axles: 2x 12,000 kg (technical) Gigant with drum brake in conjunction with 8 pieces of 245/70 R17.5" brand-name tires on Alcoa Dura Bright rims Suspension: pneumatic with lifting and lowering function Second driving height + approx. 50 mm can be switched on from the cab. At a speed of 20 km/h, the vehicle lowers again. Including axle load gauge Coupling device: 2" kingpin (exchangeable, one position) WITHOUT fifth wheel supports! -> Customers use a wide square timber here, which is placed under the front frame. Braking system: Wabco EBS with axle load measuring device (Smartboard) incl. odometer Parking brake: spring-loaded accumulator Lighting system: Rear lights, 2 pairs (3-chamber light) Side marker lights LED Outline lights LED Position lights front and rear LED Reversing light and auxiliary light each in round design License plate light LED 1 piece rotating beacon, pluggable and can be switched from the cab via a separate switch Isbexvz Skjqvxmuwjhu 4 pieces LED work lights 4 pieces overwidth markers, double-secured (knob screw and pin) with LED lighting, red/white Steering: Tridec HF-E (hydraulic displacement steering on both axles) including automatic lane keeping and straight-ahead function. Remote control Tridec (radio remote control) can also be used in cable mode Painting: Complete steel structure blasted and primed with a special adhesion primer after welding. Subsequent 2-component paint in RAL color. Axles and wheel hubs are black or, for an extra charge, painted in RAL color. Other components are galvanized or painted / powder-coated or made of aluminum (with or without anodizing) Approval: including §13 certificate including §70 certificate (customer must provide a suitable and approved 3-axle semi-trailer tractor) including, among other things, a circular test at TÜV Nord in Meppen. This is a non-binding offer. Subject to prior sale, errors and changes. Axle configuration...

Condition: used, Year of construction: 2021, Manufacturer: Robopac Model : Robotape 50 M Year : 2021 Type: Semi-automatic taping machine Conveyor belt speed: 22 m/min Adhesive tape width: 50–75 mm Minimum box dimensions (LxWxH): 150x110x110 mm Maximum box dimensions (LxWxH): ∞x500x500 mm Minimum weight per box: 1 kg Maximum weight of boxes: 50 kg Power : 0,4 kW Supply : 400 V – 50 Hz Weight : 170 kg   Gjdpfxsyy S Imj Abisbw

Condition: new, neu ca. 2 - 4 Wochen ab Auftr 3420 € 2000 x 1000 mm 850 mm 8000 kg 712 kg 200 mm 28 mm - Fully milled table top 25 mm in S355J2+N with high degree of accuracy (+/- 0.05 mm) and rounded edges and holes - Hard chrome-plated table surface Cr75 The main advantage of our tables compared to conventional systems is with the hard chrome plating Cr75, that this process achieves a much deeper penetration into the base material of up to 0.07 mm and the hardness of the surface reaches up to HV750. This also ensures optimum and lasting anti-spatter adhesion on the surface, which is one of the most efficient on the market. Gbsdpfx Aowir A Nebiow - Exact dimensional and fitting accuracy of the tools with 28 mm perforation (compatible with comparable premium suppliers) - Grid lines 100 x 100 mm - 4 solid table feet withload capacity 2 ton/feet and levelling option - Different foot variants available (standard, height-adjustable and with castors) - Load capacity 8 to - All-round 200 mm high side cheeks with diagonal perforation - 2-sided millimetre scaling - Substructure with stiffeners OPTION (PRICE ON REQUEST): Diagonal holes

Year of construction: 2014, operating hours: 3,100 h, condition: excellent (used), functionality: limited functionality, MYDATA MY500JP Jet Printer 2014 in excellent condition with exceptionally low operating hours (approximately 3,100). Kept and used in a clean environment. Complete system supplied with offline programming PC, MYCAM JP software, 2D Inspection & Repair option, SMT Adhesive option, manual load tables and associated documentation. There are also some spares included which we can bundle into a sale deal for an appropriate price. Visits/Inspection are welcome by appointment. An excellent opportunity to acquire a MY500JP suitable for high-mix, low-to-medium volume SMT production. The machine exhibits an intermittent issue affecting movement on the X-axis during camera positioning. On occasion, a slight jitter or vibration is observed, which can prevent the vision system from reliably locating the PCB fiducial during initial board loading or machine initialisation. The fault is intermittent and does not occur consistently. Most of the time, reloading the PCB allows operation to continue normally. Occasionally, a machine restart is required. The root cause has not been determined, but the issue appears to be associated with the X-axis motion control system. Potential areas for investigation include the servo amplifier (drive), encoder, encoder cable or other associated motion control components. Despite this intermittent behaviour, the machine was used in active production of complex PCB assemblies, including fine-pitch BGA boards, for approximately 12 months prior to being replaced as part of an equipment upgrade. The machine is therefore offered for sale on the understanding that diagnosis and repair of this intermittent fault is outstanding. Gbjdpfxezlx E Te Abisw Included: MYDATA MY500JP (2014) Approx. 3,100 operating hours MYCAM JP offline programming PC and software 2D Inspection and Repair option SMT Adhesive option Manual loading Technical documentation 4pcs AE04 ejectors Bundle of spare parts Not included: Solder paste Cassette (Holding Assembly), Solder paste, Purge Gel, Filter boxes Conveyors

Condition: used, Year of construction: 2004, workpiece height (max.): 60 mm, workpiece width (max.): 2,800 mm, workpiece length (max.): 1,300 mm, edge thickness (max.): 20 mm, feed rate X-axis: 40 m/min, The machine has the following configuration: Gluing Gluing system: EVA Adhesive application: single-sided and double-sided Scoring saw Motor power: 2.2 kW Speed: 6,000 min⁻¹ Profiling unit Motor power: 6.6 kW Speed: 6,000 min⁻¹ Cross-cutting saw unit Gsdpfxoz Ekczj Abijbw Number of motors: 2 Edge trimming unit, top and bottom Number of motors: 2 Motor power: 1.85 kW Speed: 12,000 min⁻¹ Edge rounding unit Number of motors: 2 Motor power: 1 kW Speed: 12,000 min⁻¹ Profiling unit with automatic, time-controlled engagement Motor power: 6.6 kW Speed: 6,000 min⁻¹ Profiling unit with automatic, time-controlled engagement Motor power: 6.6 kW Speed: 6,000 min⁻¹ Belt sanding unit Motor power: 2.2 kW Belt sanding unit Motor power: 0.75 kW Brushing unit Motor power: 0.75 kW Brushing unit TECHNICAL DETAILS Workpiece length: 280–1,300 mm Workpiece width: 320–2,800 mm Workpiece thickness: 8–60 mm Edge thickness: max. 20 mm Feed speed: max. 40 m/min MACHINE DETAILS Control system: ICOS OPEN EQUIPMENT Chain conveyor with drive shoes Pressure bar with rubber belt Edge heating lamps Roller magazine Hot-melt adhesive tank Hot-melt adhesive pre-melter Edge pressing unit with 9 pressing rollers CE-compliant The machine is sold and delivered in its actual and legal condition ("as is, where is") based on photographic documentation and technical/commercial documents with a descriptive character. The buyer has the right to inspect the goods before collection and assumes responsibility for the installation, securing, and use of the machine at the destination. External reference: 6561

Year of construction: 2025, condition: like new (used), Ulma VTI 640 Technical Specifications Model: VTI 640 Condition: Like new (fully functional) Year of manufacture: 2025 Performance: Up to 20 packs/minute (depending on film and product characteristics) Type of packaging: Flow pack Features Gbsdoz Ru Rbepfx Abiew ✅ Wash Down IP 66 design for hygienic applications ✅ Machine suitable for laminated film ✅ Machine prepared for MAP (Modified Atmosphere Packaging) ✅ Forming tube for bag width 300mm ❌ Label dispenser ✅ Printer Videojet 6330 ✅ Signal for printer / labeler ❌ Double film roll holder ✅ Automatic film centering ✅ Quick-change system for film with vacuum adhesive table and cutter ✅ Squeegee for controlling the pack volume ✅ Synchronization signals for upstream and downstream equipment ✅ Inclined discharge conveyor ✅ Volumetric pneumatic filler with 200 – 300 liter tank Documentation & Operation Language (documentation & HMI): German (other languages available upon request)

Condition: used, Year of construction: 2004, Control unit, factory reconditioned used cleaned functionally tested partially overhauled Manufacturer: Ganner Type: 252/N Year of manufacture: 2004 Machine no.: 756 484 CE type-tested Adhesive container capacity: 5 liters Dowel diameter: 8 mm Dowel length: 30 mm With adhesive supply Water flushing Gbjdpfoz I D Aaox Abiow Glue gun mobile Space requirement approx. L x W x H mm: 600x600x1200 Weight approx. kg: 100 Location: 97447 Gerolzhofen, free loading, unpacked Handover in the current condition as inspected without guarantee and warranty

Condition: new, Table for hard cover making 1050×740 The device is brand new, with a 12 month warranty. European production, based on brand-name components. Work cycle: The operator manually hands the covering material to a gluing device in which the animal glue is automatically applied (working temperature 60-70’C). The covering material sheet with the glue applied, the operator places it manually on the stage, then manually adds the cardboard and joint board sheets. The operator prepares the pre-prepared cover manually to the device in which the top and bottom of the covering material are wrapped up and glued (patented brush system). During the sizing operation, the cover is pressed through the arrangement of the guide rollers. Covers leaving the device are immediately suitable for further processing The machine is equipped with: – A gluing machine applying glue to the top of the sheet – table with a suction – fixing elements for covering material and cardboard – a module for wrapping the cover – receiving table Technical data: Max format: 1050x740mm Min format: 140x140mm Godpfx Aoz N Shzobiobw Capacity: 100-150 covers / h Thickness of the layer: 80-170 gsm Thickness of cardboard: 1-4mm Wrap up: 13-20mm Temperature of the adhesive: 30-100 ‚C Capacity of the bender: 2-3kg Smooth speed control of rollers and brushes Types of veneer material: fabric, laminated paper, photographic paper, imitation leather, PVC, polyurethane. Dimensions of the machine: 1600x1800x1000mm Power supply: 380V Power consumption: 3.7kW Weight: 300kg We invite you to tests to our headquarters Machines are available from stock.

Condition: used, Year of construction: 2009, - Veneer strip lengths (fiber direction): 350-1500 mm - Veneer strip widths (cross-fiber direction): 50-500 mm - Veneer surface width (cross-fiber direction): min. 260 mm - Veneer strip thickness: 0.3-1.5 mm Veneer machine with direct stacking Manufacturer: Fischer & Rückle Type: FZR 15 / DAR 22 Year of manufacture: 2009 Cross-feed splicer For the most efficient cross-gluing of parallel-joined veneer strips into endless or component-specific veneer surfaces. The cut or rotary-cut veneers must be pre-glued, using PVAc or urea adhesives. This cross-feed splicer is the most economical alternative to longitudinal splicers for cross-fiber applications. Production Approx. 17-20 joints/min Technical data Veneer strip lengths (fiber direction): 350-1500 mm Veneer strip widths (cross-fiber direction): 50-500 mm Veneer surface width (cross-fiber direction): min. 260 mm Veneer strip thickness: 0.3-1.5 mm Equipment Feeding device for efficient and convenient semi-automatic feeding of veneer strips. Panel automatic for component-specific surfaces with pre-sorted components and a pre-selected number of veneer strips. Features - Perfect bonding of cut or rotary-cut veneer of all wood species, even with wavy or undulating veneer - Unique, tried-and-tested horizontal pressing system that results in completely closed, solid glue joints - Solid, robust construction for a long service life, reliable and fail-safe operation - Easy operation thanks to screen, clear symbols, separate pressure gauge with direct access, etc. Gbsdpfxezuz Hle Abijw - Liftable pressure beams for quick and easy access to the heating plates for cleaning - Few wear parts, low costs for service and maintenance Cross-cutter For cutting to a pre-set format width (across the fiber direction) immediately after splicing. The straight alignment of the veneer must be observed and, if necessary, corrected by pressing a button. When working in endless mode, the required distance to the direct stacking device is set. Direct stacking device DAR-22 For outputting and stacking the veneer surface immediately after splicing or cutting. The spliced surfaces are gently output and stacked without this compact direct stacking device exerting any mechanical forces. Min. veneer sheet lengths (fiber direction): 350* - 1500 mm Veneer sheet widths (across the fiber direction): 260 - 500* - 2200 mm Stack removal from the left, right, or rear Max. stack height: 500 mm *Reliable stack alignment not guaranteed Note: The technical data and descriptions are a transcript of the original order confirmation. The data is for informational purposes only and is not binding.

Condition: used, Year of construction: 1993, Second-hand machine Year of manufacture: 1993 Bench-top machine The zigzag thread used as the adhesive medium is applied from below Automatic thickness and tolerance compensation for measured veneers Veneer from approx. 120 mm in length, 35 mm in width and a thickness of 0.3–2 mm Electrical connection: 230 V Gbjdpozk N D Rsfx Abiew Column reach 700 mm Material feed rate approx. 6 m/min. Weight approx. 54 kg Availability: at short notice Storage location: Flörsheim

Condition: used, Year of construction: 1989, Used Machine Features and Technical Specifications: - Small machine for processing molded parts - Processes hot-melt adhesive-coated edging material, which is reactivated using hot air - The workpiece is automatically fed by pressing it against the central, driven pressure roller, ensuring uniform adhesive reactivation and, consequently, reliable bonding - Thermostatic temperature control via a dial thermostat - Maintenance-free three-phase hot-air blower for continuous operation - Automatic airflow deflection - Pneumatically operated roller cutting device trims even the toughest veneer and PVC edges - Foot switch for processing molded parts - Workpiece thickness: 10–50 mm - Heating power: 3 kW - Connected load: 3.3 kW - Workpiece width (min.): approx. 25 mm - Edge thickness approx. 0.5–1 mm Gbedpfezk N Ehsx Abiow - Minimum inner radius approx. 25 mm - Feed rate 4 m/min. - Pneumatic pressure: 6 bar Weight: approx. 105 kg Availability: available shortly Location: Röllbach

Condition: used, Year of construction: 1996, functionality: fully functional, Max. roll diameter: 1,300 mm Roll core: 76 / 100 / 152 mm (unwinding), only 152 mm (rewinding) 2 rotogravure stations + inline adhesive coating unit Drying: diathermic oil system, vertical + horizontal tunnels Cooling rollers after each station Control: Siemens S5, DC drives Processes: barrier coating, lamination (paper + aluminum/plastic), inline primer CE certified, incl. thermal oxidizer (RTO25) and steam generator (Ferroli) Gedez It D Hopfx Abijbw

Condition: excellent (used), SCM K360 Edge Banding Machine Liquids Pre-milling cutters, Edge banding with roller, Replaceable adhesive tank Features adhesive discharge valve Pneumatic pre-cutting guillotine, Trimming saws R1-R2 top and bottom milling unit, pneumatically adjustable Corner rounding unit, pneumatically adjustable Profile trimming unit, pneumatically engaged Cleaning fluids Straight trimming unit, Gbsdpsz Sl R Nefx Abiow Max. element height 60mm Max. edge banding thickness in roll 3mm, Feed rate 11m/min Total run distance approximately 33,000m Very good condition Inspection and testing possible on-site

Year of construction: 2016, condition: used, KK PULLTESTER KKP03A / series 6 The KK pulltester is a measuring device for quality assurance in the graphic industry. It measures, with extremely high precision the bonding-adhesion of individual pages of cataloges, paperback books, journals, brochures and books. The number of pages to be measured, page numbers, order number and book block length are programmed before the measurements are taken. Technical specifications: Godpfx Aowcd Iqsbisbw Language: english book block format width: approx. 5 - 35 cm book block format length: approx. 7 - 40 cm book block format thickness: approx. 7 cm

Condition: used, Year of construction: 1998, functionality: fully functional, Equipment: documentation/manual, Six-axis industrial robots for floor mounting, suitable for all tasks with a control point or path. The main applications are: spot welding, handling, assembly, application of adhesives, sealants and preservatives, machining, MIG/MAG welding, YAG laser welding. Rated load: 125 kg Additional load at rated load: 90 kg Maximum total load: 215 kg Complete with control system Last maintenance: September 2022. Fully functional. Gedpfx Aboydl S Ejijbw

Condition: good (used), • Miter cut length (mm): 100 Gbjdpfem Sfnjx Abisw • Adhesive: Hot melt adhesive • Automatic assembly: of frame components

Condition: good (used), Year of construction: 1969, Pneumatic adhesive press, Maximum pressure: 10 bar, Adhesive bar with heating, Adhesive surface: 550 x 40 mm, Infinitely adjustable temperature setting for the lower and upper adhesive bars from 0 to 300 degrees Celsius, Infinitely adjustable adhesive dwell time, Drive power: 5 kW, 380 volts, 50 Hz, Two-hand operation with SIEMENS control. Pressure build-up via articulated lever, Maximum opening distance: approx. 30 mm. Gjded Dxqbspfx Abiobw

Condition: used, Year of construction: 2012, Overview This microbrewery had to cease operations recently. The original plan was to continue operations, but as this did not happen for various reasons, the remaining equipment is now being sold as a whole. Equipment - 800-liter brewhouse with steam jacket consisting of boiler, filter tank, lung, liquor tank, tubular cooler, accumulated osmotized water tank, and 3 necessary pumps for its operation. - Industrial osmosis and descaling equipment. - 3 atmospheric cylindrical-conical fermenters with refrigeration jacket and a capacity of 1000 liters. - 3 atmospheric cylindrical-conical fermenters with refrigeration jacket and a capacity of 1300 liters. - 1 cooling system for fermenters with temperature control panel by PLC. - 1 atmospheric monoblock bottling and capping machine for 33 cl bottles with filling capacity of 1,200 containers/hour. - 1 manual 6-spout filler for emergencies and special bottles. - Semi-automatic adhesive labeler. Gbsdpfx Abeuzpipoiow - Ribbon printer for adding variables to the labels, with rewinder.

Condition: used, Year of construction: 2004, Overview  The labeller was built in 2004 by Italian manufacturer KOSME. The machine is in a good condition, already professionally dismantled and stored in a warehouse. Two cold glue stations. One label, one neck label, one counter label + one adhesive station. The labeler is working in counter-clockwise direction Technical details - Capacity: - 6,000 bph - Labeling stations: Gbedpfxov Df I Nj Abiew - 2 cold glue - 1 self adhesive