Year of construction: 1974, Condition: used, machine/vehicle number: 82, Hydraulic frame press for sheet metal stamping with a force of 630 tons, designed for cold stamping. Fslqopgkt So Imaqjpg The vertical frame press with a welded construction consists of a table and an upper plate that are connected with screws. An electrical cabinet is installed next to the press and an oil overflow tank is located deep in the foundation, which facilitates filling the press system with oil. The pressing units are removable, which makes their assembly and repair easier. The press is controlled with a button. The size of the slider stroke is ensured by adjusting the position of the end stop. 1. Nominal pressing force, tone 630 2. Rated working pressure of fluids, KN/cm 2,200 3. Slide stroke, mm 750 4. Slider speed, mm/s a) at idle speed 215 b) during the working stroke 10 c) during the return stroke 120 5. The greatest distance between the table and the slider, mm 1400 6. Distance between posts, mm 2200 7. Table dimensions, mm a) from left to right 2220 b) front to back 1800 8. Thickness of stamping plate, mm 220 9. Table height above floor level, mm 410 10. Nominal force of the hydraulic washer, tf 250 11. Hydraulic cushion stroke, mm 350 12. Ejector speed, mm/s a) when going up 51 13. Press size, mm a) from left to right 5070 b) front to back 3000 c) height 7065 14. Press height above floor level, mm 5480 15. Weight of the press, kg 69400 Electric motor revolutions 1450 min-1 Operating voltage 400/230 V Mains frequency 50 Hz ± 1% Rated air pressure 0.7 Pa

Year of construction: 1990, Condition: reconditioned (used), Hydraulic press - has 4 independent stroke / cylinders. Deep drawing process. Manufacturing of oil and fuel filters cans. The range of details is: Sheet thickness: 0.4-0.6 mm Material type - black or galvanized steel Folqegcvfne Imaqepg Can diameter: 68mm - 96mm Can length: 50mm - 180mm The entire control was replaced, including cabling, drivers, monitor, etc.

Condition: new, Year of construction: 2025, pressing force: 150 t, table width: 1,000 mm, table length: 3,100 mm, Equipment: safety light barrier, PLACE OF PRODUCTION: TURKEY WARRANTY PERIOD: 24 MONTHS DELIVERY FROM STOCK 2025 MODEL NEW AND UNUSED 150 TONS H TYPE HYDRAULIC PRESS TECHNICAL SPECIFICATIONS TYPE STEEL CONSTRUCTION, 8 SLIDE H PRESS BODY TYPE BODY MATERIAL St52 – ERDEMİR CAPACITY (RAM) 150 TONS MOVABLE TABLE DIMENSIONS 3100 x 1000 mm FIXED TABLE TABLE DIMENSIONS 3100 x 1000 mm PARALLELITY TOLERANCE 120 micron/mt. PERIPHERALITY TOLERANCE 60 micron/mt. STROKE (RAM) 600 mm MIN. INTERMEDIATE SPACE 100 mm MAX. INTERMEDIATE SPACE 700 mm WELDING STRESS REMOVAL Stress relief by vibration WELDING APPLICATION - EN ISO 15614-1/2017 welding application certificate accredited by TÜRK-AK and approved by WPQR and WPS. (Welding applications are supervised by “welding coordination engineers” certified according to EN ISO 14731) MAX. WORKING PRESSURE 250 Bar TOTAL MOTOR POWER 22 kW– IE3 MAIN PUMP 37 cm³ – PARKER MOVING TABLE FAST Descent Speed 140 mm/sec. MOVING TABLE SPINNING SPEED 14 mm/sec. MOVING TABLE RETURN SPEED 170 mm/sec. MAIN CYLINDER INNER DIAMETER Ø 160/120 mm – Ck45 – 3 pcs. ASSISTANT CYLINDER INNER DIAMETER Ø 90/70 mm – Ck45 APPROXIMATE HEIGHT OF PRESS 4000 mm APPROXIMATE WIDTH OF PRESS 3500 mm APPROXIMATE DEPTH OF PRESS 2000 mm LOWER TABLE HEIGHT FROM THE GROUND 1000 mm PRE-FILL VALVE NG 80 – 3 pcs. HYDRAULIC UNIT PARKER COOLING SYSTEM SUCTION – CIESSE ENGINE CLASS USED FOR THE UNIT IE3 LEVEL INDICATOR PARKER AIR FILTER PARKER – 10 MICRON PERMEABILITY RETURN FILTER PARKER – 25 MICRON PERMEABILITY OIL AND HEAT INDICATOR PARKER VALVES USED PARKER LUBRICATING STYLE AUTOMATIC – (ADJUSTABLE FROM THE SCREEN) RAM STROKE ADJUSTABLE FROM THE SCREEN Felsv Inrlsq Imaqspg RAM TONNAGE (PRESSURE) ADJUSTABLE FROM THE SCREEN SYSTEM ERROR INFORMATION CAN BE SEEN ON THE SCREEN PRESS STATUS INFORMATION SCREEN VISIBLE ON THE SCREEN MOULD MEMORY CAN BE ADJUSTED FROM THE SCREEN HYDRAULIC UNIT OIL TEMPERATURE INFORMATION CAN BE VISIBLE ON THE SCREEN LINEAR DISTANCE SCHEDULE NOVATECHNIK PLC APPLICATION DELTA TOUCHSCREEN PANEL DELTA 7 ‘’ SWITCH MATERIALS SIEMENS – SCHNEIDER APPROXIMATE WEIGHT 20 TONS

Condition: ready for operation (used), Eccentric Press, Eccentric Press Machine, Eccentric Press, Digép SD-63, Used Machine Manufacturer: Digép Type: SD-63 Dimensions: 1400 x 1800 x 2450 mm Table Size: 740 x 555 mm Fjlq Ior D Nb Ismaqepg Stroke: 10-110 mm Strokes per Minute: 60 Pressing Force: 63 tons

Condition: refurbished (used), Year of construction: 2004, Functionality: fully functional, TECHNICAL CHARACTERISTICS: Press Model: T130R CE Serial number: 11911 Year of construction: 2004 Nominal force: 1300 kN Nominal stroke: 7.5 mm Adjustable stroke: 16÷200 mm Stop position: TDC Ram adjustment: 100 mm Stop time: 190 ms Strokes per minute min./max.: 10/55 Maximum mould surface: 600 x 1100 mm Maximum closed mould height: 452 mm Min. closed mould height: 260 mm Upper mould mass: 140 kg Flywheel revolutions per 1°: 411 Max. insertions at 1°: 28 Installed power: KW 11 Voltage: V400 Auxiliary voltage: V24 Operating air pressure: BAR 5.5÷6 Mass: Kg. 10,000 Motorized hammer adjustment Hydraulic overload safety Inverter Complete with user manual and CE conformity and 6 months warranty. • Work surface revived on CNC machine; NEW COMPONENTS INSTALLED: • Safety guards complete with safety keys; • Clutch plates; • Motor; • Motor pulley; • Motor belts; Felq Imaev Iktlsqspg • Clutch pins and brite; • Swivel joint bearings; • Motorized hammer adjustment worm screw bearings; • Flywheel bearings; • Electric panel with touch screen; • Pedal board; • Air pressure gauges; • Hammer overtravel sensor; • Balancer cylinder gaskets.

Condition: defective spare-parts repository (used), Year of construction: 1995, Functionality: not functional, machine/vehicle number: PEE I 400, pressing force: 400 t, ram stroke: 140 mm, used eccentric press incl. functional belt device, details according to type plate, inspection possible at any time Fpslq Imast U Nwreqjg Main shaft and drive motor are to be replaced/renewed

Year of construction: 1992, Condition: used, machine/vehicle number: 530, The STEINER hydraulic press was manufactured and developed with practical aspects in mind. The hydraulic device is located on the hydraulic tank behind the press. Control blocks and valves are easily accessible from the outside and can be quickly replaced if necessary. The hydraulic radial piston pump is located on the drive console and is connected to the motor and pump mount via a coupling. The press stand is indestructible and torsion-resistant Sthal welded construction. The ironing board is screwed to the stand. The hydraulic cylinders are screwed to the press stand from above and guided through the mounting holes in the appropriate direction. The piston is connected to the piston rods via a wear ring. Four-sided, diagonal, flat grooves on the stand allow for very precise movement. Hydraulic cylinders are made of high quality material and are designed for high pressures. The piston rods are ground and hard chrome plated. The cylinder tubes are honed from the inside. Seals that have been maintained over many years are characterized by high quality and tightness. The piston rods are guided by guide bands, which are characterized by very low abrasion and a long service life. The control, control and monitoring devices for all control devices are installed in the control unit. Mutual locks ensure that no two program processes can run at the same time. The electrical control is located in a closed control cabinet. Pressing force - 8000 kN Operating pressure - 285 bar Installation height - 850 mm Stroke - 250 mm Table surface - 1550 x 1450 mm Ram surface - 1550 x 1450 mm Stand passage - 1800 mm Lateral Breakthrough in the stand on the right and left Width x height - 1300 x 1075 mm Table top thickness - 155 mm Width of the machine approx. - 3100 mm Depth approx. - 4300 mm Height approx. - 4660 mm Table height above hallway - 500 mm Table height under hallway - 755 mm Drive power - 55 kW Oil requirement approx. - 1400 liters Fpsljpgktcsq Imaqeg Total weight approx. - 60 tons

Condition: reconditioned (used), Year of construction: 1983, Functionality: fully functional, Specification: Rated pressure 50 tons Slide stroke 7-80 mm Speed 75-300 strokes/min Slide adjustment 50 mm Table dimensions 500 x 500 mm Passage between columns 400 mm Weight 8500 kg Press equipped with mechanical jaw feeder - ELMEA PM132 - Year of production of the feeder: 2004. Folq Imaetq Hqaeqepg - For high speed and precision (0.02 mm) operation. - Speed up to 1000 strokes/minute for short feeds. - Acquires motion from the press shaft by driving a gear wheel with alignment joints. Rotary motion is converted to straight-alternative motion by a crank/crank system. - Adjustment of the feed length is achieved by an accurate step screw. - The clamp opening can be adjusted to accommodate belt thickness. It can also be set up for remote control operation. - It has an emergency stop sensor for hooking into the tool and is equipped with a kinetic joint that reduces the feeding angle from 180 to 120 or 90 degrees, increasing speed during feeding. The press has been professionally refurbished by Service BTC Maszyny Stolarczyk - New touchscreen control panel and PILZ safety controller - New lubrication pump and hydraulic fuse - Warranty 6 months. - Location of the machine: 97-410 ZŁOBNICA, POLAND. - Ready for delivery.

Year of construction: 2023, Condition: new, Pressing force 150to Siemens PLC hydraulics Bosch/Rexroth stroke 400mm table area 600mm x 800mm Folq Imjkyu Hvsaqjpg

Condition: good (used), Press machine, hydraulic press, used machine Fpslq Imst A U Ireaqeg Manufacturer: SEJFO Model: 7051-3 Overall dimensions: 800 x 1400 x 2480 mm Weight: 996 kg Stroke length: 300 mm Maximum hydraulic pressure: 140 Bar Year of manufacture: 1997 Hydraulic power supply: 380 V; 50 Hz

Condition: reconditioned (used), Year of construction: 1999, Functionality: fully functional, machine/vehicle number: 160/0/31/99, ram adjustment: 110 mm, table width: 1,250 mm, table length: 750 mm, stroke adjustment: 200 mm, overall weight: 13,800 kg, pressing force: 160 t, ram bore: 60 mm, warranty duration: 3 months, year of last overhaul: 2023, Equipment: documentation/manual, Procent Pressix eccentric press from 1999 after full modernization in 2023. Fpolq Iorwxkaemaqjg Scope of renovation and modernization work: - Full disassembly of the machine - Overhaul of all components - New clutch-brake assembly - Regeneration of slider guides - Reconditioning of the eccentric cam pan - Reconditioning of the main motor - Regeneration of balance cylinders - Replacement of eccentric shaft bearings - Replacement of drive shaft bearings - New progressive lubrication system - Regeneration of the pneumatic system - Cleaning, painting

Condition: excellent (used), Year of construction: 2001, operating hours: 8,000 h, Functionality: fully functional, machine/vehicle number: 1354.18, total height: 20,000 mm, installation height: 500 mm, pressing force: 30 t, table width: 550 mm, table length: 400 mm, operating speed: 60 mm/s, overall weight: 2,500 kg, ram stroke: 300 mm, power: 7.5 kW (10.20 HP), Technical data: Pressing force 30 t Stroke 300 mm Installation height 500 mm Fold-through hole in table 120 mm Front passage 550 mm Usable table depth 400 mm Usable table width 550 mm Speed from 60 mm/sec. Speed up to 180 mm/sec. Hydraulic oil tank capacity 400 l Drive power 7.5 kW External dimensions L x W x D 1200 x 2000 x 2600 mm Weight 2.5 t With - 2-hand release - light barrier - safety cage - Infinitely variable pressure control, preselection with digital display Felq Imotrd Ubsaqjpg - Infinitely variable speed control - 8000 switch-on hours - CE marking - complies with UVV

Condition: repair required (used), Year of construction: 1981, Functionality: limited functionality, machine/vehicle number: ST-42/421-45/2390, overall weight: 35,000 kg, Hot press for forming screws. The device has been out of service for several years due to failure to meet the technical parameters of the products. Made as one of three in the application of pilot technical solutions to improve the production process. Approx. 3 years "dry" commissioning trials were carried out. The trial demonstrated problems of operation as well as functionality. Device considered without peripheral devices. Fpolq Imsu Hf R Heaqsg Fabryka Elementów Złącznych S.A. located at 14 Fabryczna Street 41-100 Siemianowice Śląskie NIP: 643 000 00 23 REGON: 000028346 KRS 0000097998 has the machines specified below for sale. Deadline for submission of offers until 22.11.2024r. Offers should be sent to the e-mail address. Machines can be viewed by appointment by phone

Condition: reconditioned (used), Year of construction: 1980, Functionality: fully functional, Technical data: Fjlq Imajtq Hhzsqjpg Force 350 ton Slide stroke (fixed) 400 mm Speed 10-25 spm Table dimensions 2700 x 1350 mm Distance table-slide 910 mm Adjustable slide 150 mm Weight ca 60 tons Voltage 400 V Working pressure 6 bar Press proffesionally overhauled by OMERA exclusive dealer: • New clutch-brake unit • New bearings in kinematic system • Replaced with new worn elements of the kinematic system (shafts, pinions, gears) • Regenerated balancing cylinders • New pneumatic system • New automatic lubrification system - progresive • New main engine bearings • New electrical cabinet equipment with wiring composed as follows: - Programable PILZ PSS4000 device - PILZ safe encoder - Fatek FBs60MCJ2 PLC - Weintek 15” touch panel - No. 10 electronic cams - No. 10 tool protection signals - Software backup with entry keys • Machine painted as a new • Instruction manual • Warranty 6 months • Machine localization: 97-410 ŻŁOBNICA, POLAND

Condition: ready for operation (used), Hydraulic Press Machine, Coil Winding Press Machine, Used Equipment Dimensions: 1340 x 1240 x 2740 mm Weight: 640 kg Fpjlq Imasu Hkfpsqjg Electrical Specifications: 400V Hydraulic Pressure: 100 bar Stroke Length: 180 mm

Condition: ready for operation (used), Hydraulic Press, Bearing Press, Used Machine Manufacturer: Stenhoj Hydraulic Model: 1T TE Pressing Force: 1 Ton Stroke Length: 300 mm Maximum Operating Oil Pressure: 16.1 MPa Fpolq Imeu Hi Tlsaqog Overall Dimensions: 700 x 1140 x 2220 mm Weight: 1000 kg Electrical Specifications: 400V; 10A-20A Hydraulic Pressure: 200 bar Adjustable Pressing Force

Condition: good (used), Eccentric press Fpslq Imasg Uf D Heqsg Stroke: 55 mm Ram adjustment: 8 – 96 mm Turn: 50 1/min Max force: 45 t Weight: 2550 kg

Condition: excellent (used), C-Frame Press, Electric Press, Servo Press, Electric Press Tox Ecoline CMB008.407.A.001, Tox Ecoline CMB008.407.A.001, Used Machine Manufacturer: Tox Model: CMB008.407.A.001 (Ecoline) Year: 2011 Weight: 900 kg Overall Dimensions: 1250 x 1400 x 2610 mm Pressure: 5500 kg Stroke: 300 mm Max Speed: 200 mm/s We are offering a high-quality servo press that is the ideal solution for all precision and high-performance industrial tasks. This press provides exceptional advantages in both productivity and quality, making it the perfect choice if you are looking for a reliable, energy-efficient, and cost-effective solution. High Precision: The servo press ensures precise control, allowing for repeatable and accurate operation, with tolerances down to micrometers. Energy Efficiency: It consumes significantly less energy compared to traditional hydraulic presses, enabling more cost-effective long-term operation. Fpslq Iouccicomaqjg Quiet Operation: Operates with low noise levels, creating a more pleasant working environment. Flexible Application: Versatile use across various industries, from automotive to fine mechanics. Programmable motion profiles allow for quick and easy reconfiguration for different tasks. Maintenance-Friendly: Minimal maintenance requirements, a reliable, long-lasting machine that leads to less downtime.

Condition: ready for operation (used), Press Machine, Traveling Head Cutting Machine, Punching Machine, Stamping Press, Hydraulic Gantry Press,Sanson Chiesa Turbo, Used Machine Manufacturer: Sanson Model: Chiesa Turbo Foljukpcysq Imaqopg Overall Dimensions: 3480 x 1040 x 2420 mm Weight: 5500 kg Electrical Data: 380V, 50 Hz Working Cylinder Diameter: 250 mm Operating Pressure: 200 bar Stroke Length: 120 mm Pressing Surface: 900 x 1000 mm Cutting Table: 1040 x 2500 mm

Condition: like new (used), 2 column hydraulic press Press force: 200 t upper stroke: 500 mm lower stroke: 200 mm Folq Imajghl N Usqspg overall dimension: 1800x2200x3700 mm Power: 10 PS Weight: 8.4 t

Condition: ready for operation (used), Design: vertical press with four columns. The vertical press platen is driven by an electric motor, Fpolq Imjtty Nkjaqeg the lower platen can be pulled out with the tool. -Dimensions: 2100x1600x3000mm -plate size: 950x1120mm -Electrical data: 380V; 43A; 22kW

Condition: ready for operation (used), Hydraulic press, four-column press, Eitel 100T Folq Isuhl E Romaqepg Manufacturer: EITEL Pressing force: 100 tons Overall dimensions: 1900x1100x3300mm Table size: 1050x800mm Stroke length: 400mm

Condition: good (used), Custom made Overall dimensions: 800 x 900 x 1700 mm Fjlq Imog Npmtoaqjpg Table size: 340 x 240 mm Opened height: 340 mm Stroke: 260 mm Working pressure: 180 bar

Condition: good (used), Overall size: 900x900x1800 mm Fpolq Imof Nkgvjaqsg Stroke length: 80 mm Weight: 702 kg The machine used for electric motor coal/carbon brush pressing

Year of construction: 1976, Condition: good (used), Ceramic press In good condition Fpjlq Imaegxf N Hsqog