Debarker

Valon Kone VK26M

Condition: reconditioned (used), B., VK26M (1974 series) with motorized discharge table: - Main engine - Feeding table ( driven ) - Output table - Control cabinet Including infeed and outfeed table, workshop inspected * - debarking capacity: 10cm - 61cm diameter - 4 main decision makers - 4 cutting blades - Rotor speed =235 rpm / min - Rotor öppning=65cm - 30 KW motor, speed 1500/ min - Speed: 17-42m / min - 3m or longer ( length of wood ) Dimension ( without infeed and outfeed table ) L= 9840mm Entry table: 3540mm x 1000mm x 1900 Main engine VK26M : 2530mm x 2200mm x 2350 Outfeed table ( motorized table ) : 3170mm x 1000mm x 1300 RENOVATION: Item 1 1 Content: Disassembly of machinery, washing, sandblasting, priming and painting, repair, assembly Pos 2 1 Material of blade shafts on rotor new bearings and sealing (if necessary) Item 3 5 5 Other material: Piece V-belt for rotor drive Pos 4 1 Gear oil Pos 5 1 Material: Abrasive + Colours Pos 6 4 Valonkone piece peeling knife Pos 7 4 Valonkone piece Pre-separator Pos 8 1 Switch cabinet : with 3-phase delta-start for 30 kw main motor with 3-phase delta start for 11 kW geared motor with start for 4 kw gear motor supply with start for 4 kw gear motor output Main Starter Emergency STOP Bedpsfn Iu Ijfx Acvjda

Condition: used, Year of construction: 2004, SECOND-HAND FINGER JOINTING LINE WEINIG GRECON PROFI JOINT MOD. PJ 150/500 - CE - Wood entry length 150 - 700 - Wood width 40 - 150 mm Bedpfx Acswry I Eovsda - Wood thickness 18 - 80 mm - Wood exit length 3,000 - 6,100 - Press length 6100mm - Press force 105 kN - Milling unit motor 15Kw - Scoring unit 5.5Kw - Year 2004 CE

Condition: reconditioned (used), Year of construction: 1974, Valonkone VK26M (1974 series) with outfeed table: - Main machine - Feeding table ( driven ) - outfeed table - switch cabinet IMMEDIATELY available from stock Including infeed and outfeed table, workshop inspected * - Debarking capacity: 10cm - 61cm diameter - 4 main cutters - 4 cutting knives - Rotor speed =235 rpm / min - Rotor opening = 65cm - 30 KW motor, speed 1500/ min - Speed: 17-42m / min - 3m or longer ( wood length ) Dimension ( without infeed and outfeed table ) L= 9840mm Bdjdpfotwrp Djx Acvsa infeed table: 3540mm x 1000mm x 1900 Main machine VK26M : 2530mm x 2200mm x 2350 Outfeed table ( motorized table ) : 3170mm x 1000mm x 1300 RENOVATION: Pos 1 1 Content: Machine disassembly, washing, sandblasting, priming and painting, repair, assembly Pos 2 1 Material blade axles on rotor new bearings and sealing (if necessary) Item 3 5 5 Other material: piece of V-belt for rotor drive Item 4 1 Gear oil Item 5 1 Material: Abrasive + paints Item 6 4 Valonkone piece peeling blade Item 7 4 Valonkone piece Pre-separator Pos 8 1 Switch cabinet : with 3-phase delta start for 30 kw main motor with 3-phase delta start for 11 kw geared motor with start for 4 kw geared motor infeed with start for 4 kw geared motor output Main starter Emergency STOP

Year of construction: 1970, condition: good (used), functionality: fully functional, Stenner RESAW VHL 48 manufacture Stenner UK S/N J2103 year 1970 (original photos coming soon) Principal Dimensions and data: Diameter of saw pulleys: 48"= 1220mm Width of saw pulley face-standard 5" (127mm) Width of saw pulley face-optional 5 1/2" (140mm) Maximum width of saw - standard 5 1/2" (140mm ) Maximum width of saw-optional 6" (150mm)A Minimurn length of saw 25" 8" (782mm) Maximum height of top saw guide above table 28" (710mm) Table height from floor level 31 1/2" ( 800mm 9 Overall height from floor level 9.1" ( 2770mm) Overall width 8.1" (2460mm) Speed of saw pulleys,r.p.m. 8,000 (2440m/min) Horse power range 30 kW Size of fast and loose pulleys 20"x6 1/2" Feed speeds, standard; f.p.m. or m/min. 0-140 (0-42.6m) Shipping Specification : Standard Machine : Net weight, lbs. 3583 kg The VHL 48 is a band resaw of advanced design embodying many new features resulting from a close study of user-operator requirements, and the necessity to provide fast and accurate sawing coupled with ease of operation, reduced operator fatigue, low maintenance, and increased safety. The design caters fully for these essential factors which contribute to a markedly high level of operating efficiency. The machine is primarily designed for the planning mill and joinery shops. The thin bandsaw gives the machine a high timber Bdodpfevuhumox Acvea recovery rate; the loss due to saw kerf being very low. Compared with a circular radial-arm resaw, the VHL is faster, less wasteful, and uses less power for a given class of work general The VHL is made only as, a left-hand machine, i.e. the saw pulleys run in an anti-clockwise direction when looking in the direction of the feed. The drive is normally arranged to give a saw speed of 8,000 feet permin. (2440m l/min.) Main Drive The main drive is applied to the bottom saw pulley spindle which is prepared for vee belt, flat belt, or flat belt fast and loose pulleys to suit the proposed driving unit. Complete electric motor drives, up to 40 H. P. and for most current supplies can be provided; they include two vee pulleys, set of vee belts, belt guard, motor with slide rails, starter and a master stop button which is fitted to the machine base close to the sawyer's position. horizontal rollers The horizontal rollers are 6" (152mm) diameter and extend the full opening on the fence side and 6" (152mm) beyond the table on the open side; they are normally free-running idle rollers. They can be supplied hydraulically driven as optional equipment, either with the machine or after installation; the rollers are then driven in synchronism with the main feed rolls, by a separate motor. The drive is arranged so that the open-side roller at the outfeed end rotates in the reverse direction to facilitate the return of timber to the sawyer. The roller in front of the saw is moveable sideways to permit rapid saw changing.

Condition: repair required (used), Year of construction: 1999, functionality: not functional, Prismatrice Storti 4x35hp roller input Exit command house Bdodpfx Acjlxqk Rovea machinery to restore

Condition: excellent (used), Storti RM 500 edger - Italian production - year of production 1993 - electric spacing of discs TECHNICAL PARAMETERS: - cutting width max 435 mm - cutting height max 170 mm - engine power 2 x 22kW - max element width 600 mm - minimum material length 800 mm - max disc diameter 600 mm - spindle diameter 40 mm - two upper pulling rollers - one upper pressure roller - roller motor power 2 x 1.1 kW - roller pressure with automatic jump - seven bottom pulling toothed rollers - electric disc adjustment Bdedok Talpepfx Acvea - two lasers - feed speed 25 and 50 m/min - feeding table 2950 mm - receiving table 3000 mm - drive rollers D100 mm - power of the roller feed motor 2 x 1.5 kW Transport dimensions 500x240x180 cm weight 3500 kg

Year of construction: 2005, condition: used, HIT mechanization for KVH and BSH production for components up to width 600 mm, height 300 mm, length 18 m consisting of different parts to be delivered individually or completely - layer cross pusher - various cross conveyors - workpiece roller conveyors - heavy duty roller conveyors Bdsdspiurmopfx Acvea - 5 lifting tables with 2 cross conveyors each mounted on traversing carriages - stacker - control cabinets - Roller rails - Travelling binder cut-off saw with waste disposal system

Year of construction: 2007, condition: excellent (used), Power generator 150 kVA Renault Turbo Bjdeivt Inspfx Acvoda - French production – year of manufacture 2007 – cabin TECHNICAL PARAMETERS: diesel MOT-482 engine generator Unelec engine power 120 kW generator power max 150 kVA liquid-cooled engine turbine transport dimensions (length / width / height) 310 / 150 / 245 cm weight 2000 kg

Year of construction: 1993, condition: good (used), Clamping carriage Braun WES fully hydraulic with auxiliary carriage with tracks Track width: 79 cm good condition - immediately available Bdedpfofuh Dysx Acvsa Visit also my other advertisements. I am looking forward to your inquiry.

Year of construction: 1998, condition: excellent (used), functionality: fully functional, Very stable creel roller conveyor with hydraulic lift and lowering cross conveyor. 1st part: Length 7,100 mm. Roller length 2,000 mm. Roller diameter 220 mm. Overall height 1,000 mm. Built-in hydraulic lifting and lowering cross conveyor With 4 chain strands. Spacing: 1,500 - 1,300 - 1,000 mm. Fully plated. Hydraulic model support rollers. Drive via geared motor. New bearings. 2nd part: Length 7,200 mm. Roller length 1,600 mm. Conveyor length 6,100 mm. Built-in hydraulic lifting and lowering cross conveyor with 6 chain strands. Unsupported, it is possible to convey the cut material under the roller conveyor to the left or right. Fully plated. Including hydraulic unit for both roller conveyors. Bsdpfjt Hg Huex Acveda