Used Turn Mill Center for sale (25,127)

Condition: ready for operation (used), Year of construction: 2005, operating hours: 60,683 h, functionality: fully functional, turning length: 1,524 mm, turning diameter: 820 mm, spindle speed (max.): 3,300 rpm, rapid traverse X-axis: 40 m/min, milling spindle speed (max.): 10,000 rpm, The following work was carried out on the machine: Repair/overhaul of the gearbox of the B-axis (2025) Complete maintenance (2025) Motor magazine renewed (2025) Replacement of the linear guides of the X and Y axes (2024) Renewal of the ball screws of the X and Y axes (2024) Repair of the milling spindle (2024) Including approximately 120 tools, SK 50 TECHNICAL DETAILS Turning length: 1,524 mm Turning diameter: 820 mm Travel range, X-axis: 870 mm Travel range, Y-axis: 500 mm Travel range, Z-axis: 1,598 mm Rjdozcwylepfx Aa Rsw Main spindle Spindle speed (max.): 3,300 rpm Drive power of main spindle: 30 kW / 22 kW Max. torque of main spindle: 588 Nm Spindle nose of main spindle: A2-11" Spindle bore: 104 mm Indexing: 0.0001 Counter spindle Spindle speed (max.): 3,300 rpm Drive power of counter spindle: 30 kW / 22 kW Max. torque of counter spindle: 588 Nm Spindle nose of counter spindle: A2-11" Indexing: 0.0001 Milling spindle Drive power of milling spindle: 37 kW Max. torque of milling spindle: 260 Nm Milling spindle speed range: 0-10,000 rpm Rapid traverse, X-axis: 40 m/min Rapid traverse, Y-axis: 40 m/min Rapid traverse, Z-axis: 40 m/min MACHINE DETAILS Control system: Mazatrol 640M PRO Tool holder: SK50 Number of tool positions: 120 Operating voltage: 400 V / 50 Hz Connected load: 104 kVA Required installation area (L x W): 7 x 3.5 m Operating hours: 60,683 h EQUIPMENT Approx. 120 tools, SK 50 Variable speed adjustment Tool magazine, 120 positions High-pressure coolant, 70 bar Renishaw probe (new in 2025) Laser measuring system for rotating tools Interface set Air/water cooling through the spindle Overload monitoring system Chip conveyor, Mayfran Consep 2000 Quick-change tool holder, SMW

Condition: ready for operation (used), Year of construction: 2018, functionality: fully functional, turning diameter: 460 mm, spindle speed (max.): 3,500 rpm, spindle bore: 86 mm, bar passage: 78 mm, controller model: Fanuc 32iTB iHMI, center width: 689 mm, CMZ turning and milling center including GL20II gantry loader! TECHNICAL DETAILS Turning diameter over bed: 760 mm Turning diameter over cross slide: 600 mm Maximum turning diameter: 460 mm Distance between centers: 689 mm Travel distance tailstock: 640 mm Travel distance X-axis: 310 mm Travel distance Z-axis: 640 mm Travel distance Y-axis: +70/-50 mm Rsdpfx Aaezdrzxj Row Travel distance B-axis: 640 mm Rapid traverse rates: 30/30/15/30 m/min Spindle speed max.: 3,500 rpm ASA 8" A2 Spindle bearing outer diameter: 200 mm Spindle bearing inner diameter: 130 mm Spindle bore: 86 mm Bar passage: 78 mm Number of tool stations: 12, all driven, 12,000 rpm Tool holder: 25x25 (50) MACHINE DETAILS Operating hours: 43,712 h Total operating hours: approx. 35,000 h Control system: Fanuc 32iTB iHMI Dimensions & Weight Machine dimensions (L x W x H): 2,542 x 1,760 x 1,880 mm Machine weight: 6,500 kg EQUIPMENT Gantry loader

Condition: ready for operation (used), Year of construction: 2010, operating hours: 5,002 h, functionality: fully functional, machine/vehicle number: NT100JG0126, turning length: 424 mm, turning diameter: 370 mm, travel distance X-axis: 380 mm, bar passage: 52 mm, controller model: FANUC FS-31iA5 (MAPPS 4), TECHNICAL DETAILS Turning length: 424 mm Maximum turning diameter: 370 mm (270 mm with turret 2) Bar capacity: 52 mm Turning-milling spindle Full indexing capabilities: Yes X-axis travel: 380 mm Y-axis travel: ± 105 mm Z-axis travel: 460 + 155 mm (ATC) B-axis: ± 120º Spindle speed: 12,000 rpm Drive power: 9/5.5 kW Tool magazine Number of magazine positions: 38 Tool holder: Capto C5 Maximum tool length: 250 mm (210 mm for tools under Ø70 mm) Maximum tool diameter: 70 mm / Ø130 mm (with/without adjacent tools) Maximum tool weight: 5 kg Lower turret X-axis travel: 155 mm Z-axis travel: 610 mm Rsdpfx Aezf H Ezja Rew Number of tool slots: 10 Tool speed: 6,000 rpm Drive power for driven tools: 1.5/1.2 kW Main spindle Spindle speed: 6,000 rpm Drive power: 11/7.5 kW Spindle bore: 73 mm Chuck type: Hollow chuck (8") Manufacturer: KITAGAWA Spindle nose: JIS A2-5 Maximum torque: 223 Nm Counter spindle Spindle speed: 1,000 rpm B-axis: 4 fixed positions, 0º, -30º, -180º (-225º for overhang onto conveyor, if available) MACHINE DETAILS Control: FANUC FS-31iA5 (MAPPS 4) Potential rated power: 39.24 kVA Dimensions & Weight Dimensions (L x W x H): 2,705 x 2,425 x 2,385 mm Weight: 8,800 kg Operating Hours Power on: 54,061 h Spindle 1 operating hours: 9,813 h Spindle 2 operating hours: 5,002 h EQUIPMENT Chip conveyor Signal lamp High-pressure pump Air blow nozzle outside the spindle Foot switch (dual) for main and counter spindle

Condition: excellent (used), Mazak Quickturn Nexus 300 CNC Lathe Capacity Maximum bar size diameter - 77mm Maximum cutting dia - 420mm Maximum swing - 680mm Spindle Main spindle speed : Max 4,000rpm / Min 35rpm Main spindle workpiece weight ( including chuck) 450kg Spindle bore - 88mm Spindle centre line - 1080mm Spinel nose - A2-8 Axis Travel X axis 225mm Z axis 680mm Cutting feedrates (x axis max) 8m/min (z axis max ) 8m/min Rapid traverse X axis (max) 30m/min Z axis (max) 25m/min Turret Toolsize turning tool shank - 25 x 25 Turret indexing time 1/2 full turn 0.8 secs single step 0.2 secs No of stations on drum turret 12 Tailstock (not chucker) Body movement motor driven Rsdpozh Ndxjfx Aa Row Body stroke 645mm Mounting taper No5 Standard centre supplied No5 Chucking systems Chuck cylinder S2078-15Y Chuck Type B210A815X Jaw stroke on diameter 8.8mm Main chuck diameter 10" Mazatrol PC Fusion CNC 640T Nexus CNC Control

Condition: good (used), Year of construction: 2011, Maximum machining diameter 42mm, maximum machining length 175mm, spindle power 7.5/5.5Kw , spindle speed 5,000rpm, 8 station turret, milling speed 5,000rpm, Redpfx Aajzg Egmo Rew Fanuc OI-TD control, 3 jaw chuck, parts catcher.

Condition: excellent (used), Year of construction: 2019, Swing 806mm, Swing over cross slide 527mm, maximum cutting diameter 457mm, 762mm between centres, 584mm maximum cutting length, 0.01 degree C axis, 3000rpm Milling 3.7kW, +/- 50mm Y axis, 76mm Bar capacity, 22.4kW Spindle Motor, 3400rpm spindle, 24m/minute rapid feedrate, Rsdjzg Efijpfx Aa Rjw 24 Station turret, swarf conveyor, tailstock, tool setter, coolant,

Condition: excellent (used), Year of construction: 2020, 2020 Vulcan TC250M CNC Turn/Mill Slant Bed Lathe With Fanuc Series Oi-TF Plus Control Auto Strong N-210 Ø250mm 3 Jaw Power Chucks. Swing Over Bed Ø600mm. Maximum Turning Ø316mm. Working Length 435mm. Spindle Bore Ø77mm. Bar Capacity Ø65mm. Axis Travel 'X'=185mm, 'Z'=490mm. Rapid Traverse 'X'=30m/min, 'Z'=30m/min. Cutting Feed Rate 0.001-500mm/rev. Speed Range 25-3,000rpm (11/15kW Motor). Spindle Nose A2-6. Driven Tool Speed Range 25-4,000rpm. Sauter 12 Position Turret, Turning Tool Shank 25 x 25mm. Internal Turning Tool Shank Ø40mm. Tailstock Travel 380mm, Quill Ø75mm, Quill Stroke 85mm, MT4 Taper. Run Hours 2,139. S/No. 25S1001 (2020). NOTE: This item will be loaded to buyer's vehicle, a loading charge of £250 + VAT will be added to the buyer's invoice. With Coolant System (190L Tank), Chip Conveyor, Filtermist S800 Mist Extraction Unit, Programmable Tailstock, Parts Catcher, Tool Setting Arm, Quantity Of Assorted Driven Tool Unit, Turning Tool Holders, Foot Switch, Signal Tower & Manuals. Overall Dimensions L3,160 x W1,805 x H1,935mm. Approx Weight 5,000kg. NOTE: This item will be loaded to buyer's vehicle, a loading charge of £250 + VAT will be added to the buyer's invoice. Rjdpfx Ajzfqfloa Row

Condition: excellent (used), Year of construction: 2017, Maximum turning diameter 300mm, maximum turning length 510mm, spindle speed 6,000rpm, milling speed 6,000rpm, sub-spindle speed 6,000rpm, Rodjzcy S Repfx Aa Rew main spindle bar capacity 42mm, 2 X 12 station turrets, spindle power 11Kw, Y axis + /- 32mm, swarf conveyor, coolant., Fanuc OI-TF. barfeed unit.

Condition: good (used), Year of construction: 2015, Maximum turning diameter 255mm, distance between collet chucks 639mm, swing over bed 270mm, spindle speed 4,000rpm, milling speed 6,000rpm, sub-spindle speed 5,000rpm, main spindle bar capacity 66mm, sub spindle bar capacity 52mm, 3 X 12 station turrets, Rodpfxezcy Ilj Aa Rew spindle power 15Kw, Y axis + /- 40mm, swarf conveyor, coolant., Fanuc 31i.

Condition: used, Year of construction: 2000, Hardinge VMC 600 II CNC Vertical Machining Centre with Fanuc Series O-MD CNC Control, Table Size 750mm x 500mm, 20 Tool ATC, BT40 Spindle Taper, Manuals & BT40 Spindle Tools. S/No. NVAAOF0060 (2000) Rsdpozdtkhefx Aa Rsw Location: This lot is located in Burton on Trent, UK. A charge of £300 for dismantling and loading onto suitable transport will be automatically added to your invoice should you be successful in purchasing this item. Blocking and securing will be at the cost of the purchaser.

Condition: used, Year of construction: 2005, Technical details: turning diameter: 275 mm turning length: 900 mm spindle passage: 65 mm power capacity at 100 % load: 25/20 kW spindle turning speed range: 1 - 5000 U/min spindle diameter in front bearing: 110 mm c-axis: 1 - 500 U/min. number of workpiece supports: 4 tool turret: 1 x-axis: 290 mm y-axis: 165 mm z-axis: 360 mm b-axis: 360 ° rapid speed: 18/30 m/min number of tools: 2x2 + 2x2 number of driven tools: 2x2 + 2x2 mm toolpiece turning speed range: 8000 / 2000 U/min power capacity: 25% ED 5,8 kW tool taper: TRAUB 60 tool turret: 2/3/4 x-axis: 170 mm z-axis: 600/950 mm y-axis: +/- 60 mm rapid speed: 18/15/30 m/min number of driven tools: 10 mm toolpiece turning speed range: 1 - 6000 U/min power capacity: 25% ED 5,8 kW tool taper: DIN 69880 40 x 63 total power requirement: 95 kW weight of the machine ca.: 16 t dimensions of the machine ca.: 10,0 x 3,5 x 3,0 m with CNC TRAUB TX 8i, Barloader TRAUB Stamag DNH61 / 3000, Main and Sub spindle with C-axis 1 support with B-axis 3 turret supports Rodpfswp D Nbox Aa Rew dust exhauster, coolant attachment with coalescence-seperator and chip conveyor 2 pc. 3-jaw chuck SMW KNCS-N 170-43 2 pc. HAINBUCH Spanntop chuck 40 pc. various tool holder non-driven 6 pc various tool holder driven Spare parts package *

Condition: good (used), Year of construction: 2012, maximum machining diameter 380mm, Redpfjzaz Uzsx Aa Rew maximum machining length 508mm, bar capacity 74mm, spindle speed 4,000rpm, spindle power 18.5Kw, milling speed 4,500rpm, milling power10Kw, sub-spindle speed 6,000rpm, sub-spindle power 5.5Kw, Y axis -51/+51mm, 12 station turret, Mazatrol Matrix Nexus control, swarf conveyor, parts catcher , tool setter, 3 jaw chuck and Barfeed unit.

Condition: used, Year of construction: 2010, greates pass round over bed 700 mm swing diameter over slide rest 380 mm max. turning diameter 410 mm control HEIDENHAIN - 4290 max. Spindle speed 5.000 U/min. centre distance 975 mm travel -x axis 300 mm travel -y axis 120 (+/- 60) mm travel -z axis 850 mm numbers of positions in the tool changer 12 tool taper VDI40 CNC Turning- and Milling Center | DMG - CTX 800 Beta equipped with a turret for driven tools, SCHUNK lathe chuck (Ø 315 mm) as well as tailstock and chip conveyor. Rjdpfjzhpagex Aa Rew An extensive tool package is in the Scope of delivery includes. The machine is in a well-maintained condition. - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - #Tags: CTX800beta | CTX800 beta | CTX-800

Condition: good (used), Year of construction: 2007, operating hours: 88,040 h, functionality: fully functional, machine/vehicle number: 07400003691, turning diameter: 120 mm, spindle bore: 118 mm, rapid traverse X-axis: 30 m/min, rapid traverse Y-axis: 15 m/min, rapid traverse Z-axis: 30 m/min, total height: 2,500 mm, total length: 5,500 mm, total width: 2,500 mm, overall weight: 11,000 kg, controller manufacturer: SIEMENS, controller model: SINUMERIK 840 D POWERLINE, DMG GILDEMEISTER TWIN 102 CNC Turning and Milling Center - Recorded spindle hours: 43,558 - Spindle speed range: 3,200/5,000 rpm - Swing diameter: 270 mm - Spindle distance: 900 mm - X1 axis travel: 290 mm - Z1 axis travel: 650 mm Redpfxoyaqgyo Aa Row - X2 axis travel: 180 mm - Z2 axis travel: 650 mm - Y1 axis travel: ±40 mm - Z3 axis travel: 670 mm - X3 axis travel: 175 mm - Max. bar diameter: 100/104 mm - Number of driven tools per tool turret: 12 - Including chip conveyor, with 2 tool turrets (each with 12 tool stations), main and counter spindles, as well as foot switches Attention, the machine has the following defects: - The B-axis is defective (mounted on turret 1) - Guideways and drives show age-related wear - X2 axis (guide rails) runs slightly out of alignment by approximately 0.03 mm (should be re-measured) - Occasionally, axis reference value setting in the control system fails - The hydraulic pump was replaced after a failure and is now installed externally as a standalone unit FCA D-58256 Ennepetal, loaded on truck at a mutually agreed date at the end of February 2026.

Condition: good (used), Year of construction: 1999, - Control system: Heidenhain CNC Pilot 3190/4290 - Turn-Plus software update - Turning diameter: 500 mm - Turning length: max. 635 mm - Spindle speed: 25-5000 rpm - 12-station turret, no driven tools - Tool holder VDI 30 Rsdpfozggahox Aa Rsw - Tailstock - Chip conveyor

Condition: used, Machine Type Multi-Tasking CNC Turning & Milling Center Chuck Size 15" Main / 15" Sub Swing Over Bed 1,000 mm Swing Over Saddle 700 mm Maximum Turning Diameter Ø760 mm Maximum Turning Length 1,540 mm Maximum Bar Capacity Ø102 mm Main Spindle Speed 3,000 rpm Sub Spindle Speed 3,000 rpm Main Spindle Motor 30 kW Sub Spindle Motor 30 kW Milling Spindle Speed 12,000 rpm Milling Spindle Motor 22 kW Milling Spindle Taper Capto C6 B-Axis Rotation ±120° Y-Axis Travel ±150 mm (300 mm Total) X1-Axis Travel 695 mm Z1-Axis Travel 1,585 mm X2-Axis Travel 235 mm Z2-Axis Travel 1,540 mm Tool Magazine Capacity 40 Tools C-Axis Main & Sub Spindle Rapid Traverse 48 m/min CNC Control FANUC 31i Key Features ✔️ High-Performance Multi-Tasking CNC Turning & Milling Center Rsdpfx Aaezh H H Ro Rjw ✔️ Simultaneous Turning, Milling, Drilling and Tapping in a Single Setup ✔️ Powerful 12,000 rpm Integrated Milling Spindle ✔️ High-Rigidity B-Axis Milling Head (±120°) ✔️ Main & Sub Spindles with Full C-Axis Control ✔️ Large Y-Axis Travel (±150 mm) ✔️ 40-Tool Automatic Tool Changer (ATC) ✔️ Capto C6 Tooling System ✔️ Heavy-Duty Box Guideway Design ✔️ Excellent Surface Finish and High Machining Accuracy ✔️ Reduced Setup Time and Increased Productivity ✔️ Ideal for Complex Parts Requiring Complete Machining

Condition: good (used), Year of construction: 2015, Ref. -No.: 10652 Manufacturer: DMG MORI Type: NT 4300 DCG 1000 S Year of construction: 2015 Type of control: CNC Control: Fanuc F31iA5 Storage location: Halberstadt Country of origin: Japan Machine-No.: NT430XXXX Turning Length: 983 mm Spindle power: 18,5 / 11 kW Rodpfx Aajzh Hl Tj Rjw Travel -X Axis: 750 mm Travel -Y Axis: +-210 mm Travel -Z Axis: 1220 mm Max. machining diameter: 660 mm Number of tool stations: 100 pc Tool configuration: CAPTO C6 Tool holder: 70 pc Further information: - Control and Measurement Systems - Control computer: Fanuc F31iA5 - Tool measurement system: included - Included equipment - Internal tool cooling system + high-pressure pump - Conveyor belt - Controller - Foot switches for main and sub-spindles - Tool measurement arm - Machine manuals The machine can be inspected while powered on by prior arrangement.

Condition: ready for operation (used), Year of construction: 2007, functionality: fully functional, Monforts RNC 500 MultiTurn, year of manufacture 2007 The machine was last serviced by Monforts Werkzeugmaschinen GmbH in July 2025 and is in excellent condition. All tools and accessories are included. Inspection possible by appointment. Redpfjxcwdvjx Aa Rew

Condition: excellent (used), Year of construction: 2017, functionality: fully functional, turning length: 500 mm, turning diameter over cross slide: 290 mm, spindle speed (max.): 5,500 rpm, spindle bore: 73 mm, travel distance X-axis: 210 mm, travel distance Y-axis: 80 mm, travel distance Z-axis: 550 mm, rapid traverse X-axis: 30 m/min, rapid traverse Y-axis: 22 m/min, rapid traverse Z-axis: 30 m/min, rotational speed (max.): 6,000 rpm, chuck outer diameter: 225 mm, swing diameter over cross slide: 290 mm, spindle nose: FL 140h5, overall weight: 4,300 kg, Equipment: documentation/manual, rotational speed infinitely variable, A complete DMG MORI CTX alpha 500 V6 model, fully equipped! This machine features a C-axis, powered tooling, Y-axis, sub-spindle, and more. We acquired this machine in working order from production, and it can be inspected in working condition by appointment. Additional options & accessories: - Band filter system including high-pressure pump - DMG CELOS software - 3-jaw chuck (SMW Autoblok KNCS-N-225-66) on the main spindle - 3-jaw chuck (SMW Autoblok KNCS-N-170-43) on the sub-spindle - Chip conveyor - Coolant gun - Various VDI-30 tool holders (6 powered, 4 static) - Original DMG mist extraction system - All original documentation Weight & dimensions: 4,300 kg Redpfjzc Nlajx Aa Rsw 4066x2583x1829 mm (LxWxH)

Condition: good (used), Year of construction: 1989, operating hours: 64,136 h, Centre height: 350 mm Turning length: 1000 mm Max. swing diameter over bed cover: 600 mm Max. swing diameter over cross slide: 360 mm Spindle bore: 107 mm Speed range: 16 – 3150 rpm Feed range longitudinal & face: 0.5 – 5000 mm/min Rapid traverse longitudinal & face: 9 m/min Main drive: 30 kW Dimensions of machine with chip conveyor (L x W x H): 5400 x 2200 x 2000 mm Weight: 6400 kg Accessories / Special features: • CNC control GILDEMEISTER EPL 2 with TFT display General description: CNC manual input control system with program entry via function and numeric keypad. All information is entered in dialogue with the screen. Integrated menu technology with plain text display of all functions. Operator keypad, display, and electronic handwheel located within a separate chip guard housing. The EPL control offers the following capabilities: Redpfxevr Eh Es Aa Rjw • Direct interactive program entry and editing by the operator through the EPL control without manual technological preparation • NC programs in ISO/EIA format can be entered, output, or manually keyed in via the RS 232 serial interface Machining cycles: • Removal cycles for longitudinal, facing, and contour turning, including with allowance • Thread cutting • Undercuts as per DIN 509-Form E and F and DIN 76; grind stock programmable • Axial and radial grooves as per DIN 471 and 472, including bottom finishing • 90° radii and 45° chamfers • Automatic cutter radius compensation for cycles, undercut, groove, radius, chamfer Programming: • Block-orientated, metric/inch, diameter for absolute entry, radius for incremental entry • Full circle programming, subroutine technology, hide levels for program sections, zero point offset, mode selection via menu Program entry and output: • Interactive via guided menu or direct in dialogue • Hydraulic 3-jaw chuck Ø 315 mm with through spindle bore Ø 80 mm • Hinged chip conveyor • 12-position tool turret VDI 40, 6 standard stations + 6 driven tool stations • Coolant system • RS 232 interface • Electronic handwheel • Electric foot switch for 3-jaw chuck and tailstock quill • Lighting • 12 various standard toolholders (to be finalized on site) Overhauled servo drive for main spindle, 06/2025 Siegfried Volz Werkzeugmaschinen Rüschebrinkstr. 151-153 DE - 44143 Dortmund - Wambel

Condition: good (used), Year of construction: 2015, operating hours: 5,381 h, functionality: fully functional, machine/vehicle number: AS0211, total height: 2,400 mm, total length: 4,500 mm, total width: 2,400 mm, overall weight: 9,000 kg, controller manufacturer: FANUC, controller model: SERIES 31 i-MODEL A, Equipment: documentation/manual, Technical specifications: - Operating voltage: 400 V - Frequency: 50–60 Hz - Rated current: 80 A - Control system: FANUC SERIES 31 i-MODEL A Travel ranges: - X1 / X2 axes: 180 mm each - Y1 axis: ±45 mm - Z1 axis: 704 mm - Z2 axis: 620 mm - E2 axis: 720 mm - Rapid traverse X/Y/Z axes: 30 m/min Spindle 1: - Max. speed: 5,000 rpm - Spindle nose: A6k - Spindle bore: 65 mm - Bore in clamping cylinder: 65 mm - Chuck diameter: 210 mm Redpfxev Uh Nds Aa Rew - Drive power: 24 kW Spindle 2: - Max. speed: 7,000 rpm - Spindle nose: Ø 110 mm - Spindle bore: 42 mm - Bore in clamping cylinder: 42 mm - Chuck diameter: 140 mm - Max. chuck jaw weight: 1.25 kg - Output power: 16.5 kW Tool carrier: - 1x 10-station tool turret - 1x 12-station tool turret - All stations driven (12 stations each) - Max. speed of driven tools: 8,000 rpm Accessories: - Chip conveyor from KNOLL - Tool holders (as shown in the photos, included)

Condition: used, Year of construction: 2011, Technical details: standard turning dia.: 200 turning length: max. 810 mm control: MSX-701 MAPPS IV Rsdpfsy S Tm Usx Aa Rew greates pass round over bed: 800 mm Max. distance between centres: 1130 mm max. turning diameter: 320 mm max. workpiecediameter: 300 mm bar material dia.: 65 mm Traverse X-Axis 1: 210 Traverse X-Axis 2: 210 mm Traverse X-Axis 3: 210 mm Traverse Y-Axis 1: 110 (+65/-45) mm Traverse Y-Axis 2: 110 (+45,/-65) mm Traverse Z-Axis 1: 300 mm Traverse Z-Axis 3: 300 mm Traverse Z-Axis 2: 810 mm Traverse B-Axis: 870 mm turning speed range - spindle: 5.000 1/min Number of spindle speed ranges: 2 . spindle nose: JIS A2-6 spindle bore: 73 mm spindle bearing diameter: 120 mm C-Axis: 0,001 ° turning speed range - spindle: 5.000 1/min spindle nose: JIS A2-6 spindle bore: 73 mm bar material dia. max: 65/52 mm spindle bearing diameter: 120 mm C-Axis: 0,001 ° Number of Turrets: 3 . Number of tool stations: 16 x 3=48 pos Schank height for square tool: 20 mm Diameter of boring bar: 32 mm turret changing time (4-stations): 0,18 sec Number of driven tools: 16 x 3=48 pos max. spindle speed driven tools: 6.000 U/min. Rotary tool machining ability: M16 / Ø16 . rapid traverse X-axis: 30 m/min rapid traverse Y-axis: 20 m/min rapid traverse Z-axis: 50 m/min drive capacity - spindle motor: 25 / 22 kW power capacity - driven tools: 7,5 / 5,5 kW total power requirement: 92,7 kVA weight of the machine ca.: 9,4 t dimensions of the machine ca.: 4,0 x 2,8 x 2,4 m Accerories Chip conveyor Coolantsystem C-axis in main and sub spindle Y-axis 2 x part counter total counter tool setting Overhead partsgripper with conveyor belt. Spindle 1 Chuck SMW KNCS-N 210 / 52 mm Spindle 2 Collet Chuck Hainbuch Spanntop nova Kombi Axfix 65 Robot interface CNC Turning- and Milling Center MORI SEIKI NZ 2000 T3Y2 The NZ2000 T3Y has 2 spindles and 3 turrets, and 2 turrets have the Y-axis function and built-in milling motors. This not only allows synchronized machining using 3 turrets, but also achieves heavy-duty cutting and high-speed machining using rotary tools thanks to the built-in motor turrets. *

Condition: as good as new (ex-display), Year of construction: 2025, functionality: fully functional, turning length: 520 mm, turning diameter over cross slide: 360 mm, turning diameter: 310 mm, spindle speed (min.): 60 rpm, spindle speed (max.): 4,200 rpm, spindle bore: 73 mm, travel distance X-axis: 210 mm, travel distance Z-axis: 610 mm, rapid traverse X-axis: 24 m/min, rapid traverse Z-axis: 24 m/min, total height: 1,880 mm, total length: 2,852 mm, chuck outer diameter: 210 mm, total width: 1,722 mm, collet bore: 73 mm, spindle nose: KK6, overall weight: 4,300 kg, Equipment: documentation/manual, rotational speed infinitely variable, The machine is new and has only been used for demonstrations up to now; it has not yet produced any chips. The machine is set up and operational, and can therefore be inspected. Additional options & accessories: - Preparation for a bar feeder. - Tool measuring arm. - Chip conveyor (available upon delivery, not currently included). - 10 bar high-pressure coolant pump. Redpjzcplyefx Aa Rsw - Rohm KFD-HE 210/3-KK6 3-jaw chuck. - Approx. 9 VDI-30 tool holders (7 static, 2 powered).

Condition: used, Year of construction: 2000, max swing 700 mm, X/Y 255/520 mm, 12-position upper tool turret and 8-position lower tool turret with driven tools, measuring head, tailstock, CNC SIEMENS SINUMERIK 840D, 400V 50Hz 45kW, weight 15 t Rjdoym Sx Dspfx Aa Row

Condition: used, Year of construction: 1997, MORI SEIKI SL-35 TURN MILL CENTRE Redpfjv N D Rtox Aa Row MAKE MORI SEIKI, MADE IN JAPAN MODEL SL-35 YEAR 1997 CONTROL FANUC MSC 516 CHUCK DIA 400.0 mm MAX. TURNING DIA 400.0 mm MAX. TURNING LENGT 780.0 mm SWING OVER BED 600.0 mm OVER CROSS SLIDE 425.0 mm MAX. SPINDLE SPEED 9-2500 rpm TURRET 12 STATIONS TAILSTOCK YES SPINDLE BORE 82.0 mm SPINDLE NOSE A8 RAPID TRAVERSE RATE X: 12,000mm/min & / Z: 15,000mm/min PLUS SWARF CONVEYOR TOOL SETTING PROBE GOOD RANGE OF TOOLING MACHINE MANUALS CLEAN