Used Prokuwa Plastic Gmbh for sale (74,700)

Condition: good (used), Year of construction: 2012, operating hours: 12,078 h, functionality: fully functional, pressing force: 88 t, filling opening width: 1,100 mm, filling opening length: 1,800 mm, bale width: 1,100 mm, bale height: 750 mm, bale weight: 750 kg, overall weight: 30,000 kg, oil tank capacity: 2,000 l, power: 98 kW (133.24 HP), volume flow: 643 m³/h, Technical data baler: Manufacturer HSM GmbH + Co. KG, Germany Type VK 8818 R-FU Year of construction 2012 Total operating hours: 12,078 hours, as of September 2025 Pump operating hours 6,616 hours (effective pump running time) Number of bales pressed: 65,792 bales, as of September 2025 Main press force 880 kN Specific pressing force 120 N/cm² Pressing force cutting edges free rammer 120 kN Dimensions of feed chute 970 x 1,800 mm Theoretical cycle time in idle mode 8.3 seconds Theoretical throughput capacity 643 m³/hour Bale dimensions 1,100 x 750 mm, the length is variable 600 up to 2000 mm Drive power 2 x 45 kW frequency-controlled Connected load 98 kW Total current consumption 192 A Fuse protection 250 A slow-blow 5-fold horizontal tying, fully automatic Throughput rates with a bulk density of 20 kg/cbm 12.86 t/hour Bulk weight of 50 kg/cbm 32.15 t/hour Bale weights with a bale length of approx. 1.2 m 650 up to 750 kg/bale, depends on materiel Hydraulic oil tank capacity 2000 litres PLC control Siemens S7-300 Siemens TP 700 control panel Press dimensions assembled 18,000 x 4,300 x 3.270 mm (l x w x h) Press dimensions with conveyor system 18,000 x 22,000 x 5,765 mm (l x w x h) Transport weight baler approx 30 t (Main press approx. 20 t, press channel with bale clamp approx. 10 t) Special machine equipment: Access locking by means of key transfer system Electro-hydraulic locking of the press carriage during the tying process so that the press plunger does not change position with highly expansive materials Additional optional equipment ordered: Frequency-controlled main drive, 2 x 45 kW, with up to 40 % energy savings compared to the standard motorisation 2 x 45 kW, with the same power output Manual switch-off or switch-on of the number of strapping wires to save on strapping wire for non-expansive material Cutting-edge frei rammer with 121 kN pressing force Sensory wire monitoring, with press switch-off in the event of wire breakage or wire end Bale chute Visual warning signal, mounted on the control cabinet Condition of the baler: The entire baling system (baler and conveyor belt) is in good, operational condition. Technical data for the chain belt conveyor: Manufacturer Stadler Anlagenbau GmbH Typ chain belt conveyor KF 1800 Bjdpsxcngnefx Adxolp Year of construction 2012 Drive power 7.5 kW Belt speed 0.05 – 0.4 m/second Length of feeding conveyor 6,000 mm Height of side wall from feeding conveyor 400 mm Length of incline conveyor 9,000 mm Height of side wall from incline conveyor 800 mm Length of gooseneck 1,500 mm Incline 30° Nominal width 1,800 mm Useful width 1,700 mm Belt quality EP-500/4 Steel cleats on the rubber belt 50 x 50 mm Hollow pin chain, pitch 125 mm, rollers 36 mm Height of drive axle above ground 4,284 mm Overall height of conveyor belt 5,765 mm Transport dimensions of feeding conveyor approx. 7,000 x 2,200 x 1,250 mm (l x w x h) Transport dimensions of the incline conveyor 13,000 x 2,500 x 2,900 mm (l x w x h) Pit dimensions for the conveyor belt 14,765 x 3,260 x 1,250 (l x w x h) Scope of delivery: The conveyor belt, baling press with bale chute, and wire drawing stations are available for sale, but without the wire. Comments: The documentation (Manual, CE-declaration, electr./hydr.-drawings), are completely available. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors.

Condition: good (used), Year of construction: 2019, functionality: fully functional, conveyor belt length: 15,000 mm, conveyor belt width: 970 mm, total length: 15,000 mm, total width: 1,170 mm, motor manufacturer: SEW, belt width: 880 mm, Belt conveyor/ belt conveyor/ conveyor belt -15 meter length Manufacturer: Gawronski GmbH Year of construction: approx. 2019 Machine type: Belt Condition: Used Total length: approx. 15000 mm Total width incl. motor: approx. 1170 mm Total width without motor: approx. 970 mm Conveyor width: approx. 900 mm Belt width: approx. 880 mm Belt type: longitudinal grooves Steel frame Frame height: approx. 185 mm Color: black and yellow Including SEW motor with inverter In stock: 1 piece The conveyor technology has run until dismantling. Condition: fully functional, with signs of use Ideal for fast material transport Pick-up address: Industriestraße 5 (47918 Tönisvorst) Bedjttck Ujpfx Adxolp Expertly dismantled and packaged Thanks to the excellent workmanship of the conveyor technology, your material glides smoothly to its destination, even under heavy loads. Customized solutions for your intralogistics We are your competent partner for roller conveyors, belt conveyors, inclined conveyors or telescopic conveyors for loading and unloading your goods! We will be happy to provide you with an individual quotation or advise you on the design or installation issues. Simply let us know your requirements and the local conditions. Take advantage of our many years of experience and our excellent network of specialists. For companies in a wide range of sectors, such as logistics, the pharmaceutical industry Logistics, pharmaceutical industry, trade or the electronics industry, we have already successfully realized projects. Together we will work out ways to optimize your process and material flow in a cost-effective and sustainable manner. We can even offer you fully automated sorting technology or supplementary components such as order picking racks or containers.

Year of construction: 2024, condition: new, functionality: fully functional, machine/vehicle number: CO2-1125-5000, 1x Vacuum Belt Filter Completely constructed in stainless steel 1.4404/1.4571, grates in stainless steel 1.4301 Finish: pickled and passivated Including: 1x drive roller 508x1427 1x steering roller 88.9x1850 6x support/tension rollers 88.9x1850 1x VBF frame 1x VBF hood frame 1x safety grilles (1.4301) 2x spray pipes, each fitted with 12 nozzles 6x hood brackets for vacuum tube 1x mounting materials, incl. gaskets 1x holder for control valve and paddle 2x slide blocks for tension roller HMPE100 2x bearing blocks for scraper blade HMPE100 1x scraper blade HMPE100 1x drive SEW KH87/T R57 DRN90L4TF 2x bellows d100 wbz 100-E1 2x misalignment switches 2x emergency stop switches 2x emergency stop cords 1x pressure reducer 1x hose and coupling for connection to bellows 23x nozzle holders 23x nozzles 4x rubber seals for wash cabinet 1x rubber seal for suspension conveyor 2x double wash gutters Bodpexfvahofx Adxelp

Condition: like new (used), Year of construction: 2018, operating hours: 50 h, functionality: fully functional, machine/vehicle number: 3200 0088, overall weight: 2,000 kg, total length: 7,300 mm, total width: 1,100 mm, total height: 2,000 mm, input voltage: 400 V, input current: 125 A, type of input current: three-phase, input frequency: 50 Hz, cooling capacity: 30 kW (40.79 HP), operating speed: 83 mm/s, Manufacturer IBT.InfraBioTech GmbH Art.-No. 3200 0088 Technical Data Condition: As new; little used from test series Functionality: Fully functional Year of manufacture: 2018 Connected load: 58 kW Cooling capacity, water connection on-site: 30 kW Conveyor belt length: 7,000 mm Conveyor belt width: 310 mm Infeed height: 55 mm Infeed width: 308 mm TECHNICAL DETAILS Application: Conveyor oven for curing in film bonding technology Component temperature: max. 100°C Stainless steel housing (LxWxH): 7,300 x 1,100 x 1,680 mm Overall height without control cabinet: 2,000 mm Control cabinet (WxDxH): 1,200 x 600 x 2,100 mm Base frame made of stainless steel profile tube, height adjustable: ± 30 mm Conveying system Vacuum conveyor belt made of silicone, belt 310 mm wide Transport speed: max. 5 m/min Conveyor belt height: 950 mm ± 30 mm Belt infeed/outfeed openings (WxH): 308 x 35 mm Free area infeed: approx. 750 mm Free area outfeed: approx. 750 mm Conveyor belt operation: Continuous operation, adjustable up to max. 5 m/min, tracking regulation with light barrier safety system at infeed and outfeed. Loading and unloading are performed manually. Intended use The curing oven is a belt system for continuous operation with a feed speed of max. 5 m/min. Open areas at the infeed and outfeed sections are provided for loading and unloading components. The enclosed heating section houses 6 IR modules (height adjustable). The maximum component temperature is 100°C and serves to heat solvent-free adhesive between composite film layers. The return side of the belt, the rear sides of the IR modules, and the space above the heating modules are water-cooled. Components are held onto the conveyor belt by vacuum. The control cabinet is located separately from the machine outside the cleanroom. The system operates in a cleanroom according to EN ISO 14644 Class 8 and is loaded and unloaded by the operator. The equipment is exclusively for the warming of film composites. Features - 6 adjustable infrared heating modules, each with 6 infrared emitters - 6 pyrometers for precise temperature control - PU conveyor belt for efficient material flow - Integrated control and regulation system - Height-adjustable stainless steel base frame - Vacuum conveyor belt Blodpfxewnm Ukj Adxep - Cooling water distribution in the base frame (G1") - Water cooling for the belt return section and rear sides of IR modules - Mechanically lockable service doors - Operator panel mounted at the infeed on the left side - Control cabinet cooling unit, water connection on-site History This oven was intended for use in a cleanroom environment and was only used briefly for a test series. The oven was used for curing solvent-free adhesives between composite film layers.

Condition: used, We are selling a used robotic grinding and polishing system. The system is in good used condition. The system includes: - 1x YASKAWA MH20 industrial robot with NX100 controller Bjdpfx Asxlufvjdxelp - 2x belt grinding machines for grinding belts with a circumference of 3,500 mm - 2x polishing machines with oscillation and feed for polishing discs with a maximum diameter of 500 mm - 1x loading table for pallets with dimensions (LxW): 1,200 x 600 mm - 1x control cabinet If you have any questions, please do not hesitate to contact us!

Condition: like new (used), operating hours: 185 h, functionality: fully functional, warranty duration: 12 months, power: 140 kW (190.35 HP), Features: - Dust suppression - Raised filling area - Flat bottom plate on tracked chassis Bedpfx Aetwmnnodxelp Application: Classification of pre-crushed waste wood (see German waste wood classes: A1-A4), mainly as a mixed fraction, with foreign matter - ideal for thermal recycling, with full flexibility in use. Density: 200 - 300 kg/m³, moisture: < 30 %, length: max. 500 mm

Condition: reconditioned (used), Year of construction: 2014, operating hours: 5,612 h, functionality: fully functional, pressing force: 48 t, filling opening width: 1,020 mm, filling opening length: 1,250 mm, bale width: 1,100 mm, bale height: 750 mm, bale weight: 550 kg, total height: 2,800 mm, overall weight: 12,000 kg, transport height: 2,800 mm, oil tank capacity: 300 l, power: 30 kW (40.79 HP), empty load weight: 12,000 kg, volume flow: 332 m³/h, Technical information baler: Manufacturer HSM GmbH + Co. KG Typ VK 4812 Year of construction 2014 Hours of operation 5,612 hours, stand August 2025 Press power main press 48 tons Specific press capacity 58,2 N/cm² Feed channel 1,250 x 1,020 mm Theoretic cycle time 11.2 sec. Theoretic throughput rate 332 m³/hour Bale size 1,100 x 750 x 600 up to 1,200 mm Driving motor 30 kW Connected load 32 kW Rated current 59 A Tying system 4-fold horizontal, fully automatic Throughput rate at a bulk weight of 20 kg/cbm up to 6 tons/hour bulk weight of 50 kg/cbm up to 13 tons/hour Bale weight up to 550 kg, depends on material SPS controller Siemens SIMATIC S7-200 Operating panel Siemens HMI Touch Panel Filling quantity hydraulic oil tank 300 L Oil type HVI 46 Machine installation dimensions with bale chute 10,046 x 4,387 x 2,705 mm (l x w x h) Transport dimensions baler 8,500 x 2,500 x 2,750 mm (l x w x h) Machine weight press approx. 12 t Scope of delivery: Baler HSM VK 4812, without hydraulic oil, without conveyor system. Two wire reel boxes for 8 pieces 40 kg wire reels, without wire Bale chute Machine documentation in German Blodpfxevtpq Hj Adxop Comments: The press is equipped with an oil cooler and potential-free contacts for external control. The control cabinet is operated from the left in the direction of pressing, the needle unit is located on the right-hand side and can be folded back for transport. The press was partially overhauled and tested in our workshop, see photos. The documentation (operating instructions, CE declaration, electrical/hydraulic circuit diagrams) is available in German. Viewing is possible by appointment. We accept no liability for the technical details or any errors.

Year of construction: 2025, condition: new, functionality: fully functional, Aluminium box body for Iveco 70 C with 3 roller shutters, 3000-litre stainless steel water tank with 2 cleaning hatches. The box and tank are fully mounted on a subframe for Iveco All-Wheel Drive 70C. Bodpfx Ajxlkpksdxjlp

Year of construction: 2025, condition: new, functionality: fully functional, The universal laser marking system LAS 28 XLe from Systemtechnik Hölzer GmbH can be used for a very wide range of marking applications. With the integrated fiber laser you can mark almost all materials such as steel, carbide, aluminum and plastics. Depending on the requirements, the system can be equipped with a 20, 30 or 50 watt fiber laser. For permanent marking, the use of the laser is necessary in many industries. With the powerful laser software, texts, numbers, 2D codes, QR codes and logos can be realized with just a few clicks without extensive programming knowledge. Serial and article numbers are automatically incremented by the software after prior setting. In addition, the software can read data (variable information such as drawing numbers, project designations, etc.) from existing tables and automatically transfer them to predefined areas. The use of a hand scanner is also possible. The standard equipment includes an integrated PC with Windows operating system and laser software. Optionally, the laser model LAS 28 XLe can be equipped with a rotary axis (3-jaw chuck) for marking cylindrical parts. Further options, such as lateral extension arms for marking long parts, movable Z-axis, drawer systems, etc., can be realized. Made in Germany Bedexd A I Aspfx Adxslp Fiber laser 30W, 20 W or 50 Watt - Laser class 1 - Wavelength 1064nm - Marking field size 150x150mm (optionally larger) - marking software EZCAD in German / English - optional: rotary axis (3-jaw chuck) - optional: digital height measuring system - optional: exhaust system (incl. activated carbon filter) - pilot laser (simple preview, contour preview) - focus finder (simple focus adjustment) - signal light for indication of operating status - max. component height approx. 300mm - electrically adjustable Z-axis - Integrated PC with Windows operating system - frame made of aluminum profile - air cooled - Door width approx. 700mm / door height(pass-through): 400mm - Connection 230V - Dimensions: approx. 900 x 800 x 1900 mm (LxWxH) - Weight: approx. 100 Kg

Condition: new, Year of construction: 2025, functionality: fully functional, cutting height (max.): 210 mm, cutting width (max.): 2,120 mm, cutting length (max.): 9,200 mm, saw drive: 15,000 W, total length: 11,000 mm, height adjustment type: electric, overall weight: 2,500 kg, saw blade diameter: 550 mm, JRIMAC rip saw "TOP" - NEW - - Cutting length 2200 - 9200 mm - Cutting width 420 - 2120 mm - Cutting direction left - right (right - left on request) - Cutting height max. 210 mm with high-quality saw blade Ø 620 mm. - Precise and clean cut due to strong, self-supporting welded construction of the machine stand. - Carriage guidance via linear guides, with ball-bearing mounted, maintenance-free rollers. - Safety beam mounted above the machine table with 6 mm thick lamella protection. - Extraction connection Ø 160 mm installed at table height at top right and bottom left ready for connection. - Flexible and efficient working thanks to 250 mm opening of the slat guard above the top edge of the table. - Infinitely variable, frequency-controlled, powerful feed of the carriage. Bedpfjgk Nvnox Adxolp - The maximum feed speed can be adjusted. - Automatic stepless saw blade height adjustment. - Infinitely variable width stop adjustment via several operating levers. - Electronic positioning control. - JRIMAC" saw blade quick clamping system allows quick saw blade changes. - Cut release as standard (small mobile foot pedal). - Front table supports made of wood, plastic or Pertinax coating. - High work safety. - Only high-quality components are used and installed. - The electrical control cabinet is easily accessible at the front of the machine. - The machine electrics are designed for 230/400 volts, 50 Hz. - BG dust-tested - EC type-tested in accordance with Directive 2006/42/EC - Forcibly guided splitting wedge - Processing of more than 12 different materials possible - Reliable spare parts and customer service

Condition: new, Year of construction: 2025, functionality: fully functional, Plasma cutting machine for pipes and profiles Plasma cutting machine for cutting pipes and profiles. The cutting contour is defined and create by the software. The created CNC code can send to the machine via USB or network. The program can be easily choose via the 12"touch display. The automatic cutting process is started after manual insertion of the workpiece. - Tube length: max. 6000mm - for round tube up to OD = 150mm max - for square tube up to 101.6x101.6mm (4 "x4") max - maximum pipe weight 150KG per load - 4-jaw chuck - 1x automatic raw support - fully automatic cutting process - PC control with 12 "touch display - Data import via USB and network - Power consumption: 400V 3P 2KW - weight: 800KG Bjdpsg Dvdcjfx Adxelp Made in Germany The pictures show you an older bigger machine

Year of construction: 2024, condition: new, machine/vehicle number: H3000-H5000TM, Universal testing machine H3000TM-H5000TM according to DIN EN ISO 7500 The universal testing machine of the H3000TM-H5000TM series is a single-spindle machine, a robust construction made of aluminum and V2a with ball screws, ball bushing guides and toothed belt drive. The bellows cover protects the spindle and guides. The testing machine is microprocessor controlled and has a membrane keypad. The 2-line LCD display shows the force and travel. The testing machine can be used as standalone or with a PC via USB interface. The displacement is measured by means of an encoder 0.01 mm visible resolution on LCD (internal 0.0001mm). The machine is manufactured with a standard load cell: 0.03% linearity and the corresponding calibration. Optionally it is possible to add a second channel for a second load cell or a displacement transducer. The universal testing machine is manufactured with two different travels, 500mm or 1200mm (without load cell and testing tool). Further scope of delivery: Bljdjiq Hxkepfx Adxsp One load cell up to nominal load, 220 Volt cable, USB cable, description, CE declaration of conformity. For more information, please refer to the attached description. Load cell 3000N-5000N Measuring range: 5-5000N tension and compression, with nom. 2mV/V output signal, overload protection: +/- 1000%, linearity: +/- 0.05%, hysteresis: +/- 0.03%, repeatability: +/- 0.02%, with, incl. 1.5m connection cable incl. calibration certificate Long travel extensometer HE 900mm measuring travel, measuring arms motorized, including electronics Accuracy class class 1 from 1mm travel according to DIN EN ISO 9513 Measuring principle optical incremental Measuring path 900 mm , minus measuring length Display error 6 µm or 2 Resolution 1 µm Actuating force 10 cN Standard initial device measuring length (Lo) 10-100 mm, in 5 mm steps Lo adjustment is manual Measuring arm opening and closing is motorized specimen diameter 0-30 mm specimen thickness 0-30 mm sample width 0-100 mm Weight approx. 32kg Scope of delivery strain gauge complete with electronics Cutting edges round: 1 set each carbide / rubber wear parts measuring blades optional rectangular cutting edges ATTENTION: When using optional cutting edges a readjustment of the lo a readjustment of the lo stop is necessary.

Condition: excellent (used), Year of construction: 2015, operating hours: 19,750 h, functionality: fully functional, pressing force: 100 t, filling opening width: 970 mm, filling opening length: 1,800 mm, bale width: 1,100 mm, bale height: 750 mm, bale weight: 750 kg, oil tank capacity: 2,000 l, empty load weight: 33,000 kg, volume flow: 643 m³/h, Technical data baler: Manufacturer HSM GmbH + Co. KG, Germany Type VK 8818 R-FU Year of construction 2015 Operating hours 19,750 hours, as of July 2025 Number of bales pressed: 24,760 bales, as of July 2025 Main press force 1000 kN Specific pressing force 120 N/cm² Pressing force cutting edges free rammer 121 kN Dimensions of feed chute 970 x 1,800 mm Theoretical cycle time in idle mode 8.3 seconds Theoretical throughput capacity 643 m³/hour Bale dimensions 1,100 x 750 mm, the length is variable 600 up to 2000 mm Drive power 2 x 45 kW frequency-controlled Connected load 110 kW Total current consumption 213 A Fuse protection 250 A slow-blow 5-fold horizontal tying, fully automatic Throughput rates with a bulk density of 20 kg/cbm 12.86 t/hour Bulk weight of 50 kg/cbm 32.15 t/hour Bale weights with a bale length of approx. 1.2 m 650 up to 750 kg/bale, depends on materiel Hydraulic oil tank capacity 2000 litres PLC control Siemens S7-300 Siemens TP 700 control panel Press dimensions assembled 12,130 x 4,800 x 3.270 mm (l x w x h) Press dimensions with conveyor system 35,000 x 8,480 x 7,745 mm (l x w x h) Transport weight baler approx 33 t (Main press approx. 12 t, press channel with bale clamp approx. 10 t) Special machine equipment: Access locking by means of key transfer system Electro-hydraulic locking of the press carriage during the tying process so that the press plunger does not change position with highly expansive materials Additional optional equipment ordered: Frequency-controlled main drive, 2 x 45 kW, with up to 40 % energy savings compared to the standard motorisation 2 x 45 kW, with the same power output Manual switch-off or switch-on of the number of strapping wires to save on strapping wire for non-expansive material Cutting-edge frei rammer with 121 kN pressing force Sensory wire monitoring, with press switch-off in the event of wire breakage or wire end Bale chute Visual warning signal, mounted on the control cabinet Condition of the baler: The entire baling system (baler and conveyor belt) is in good, operational condition and is cleaned, lubricated and maintained by the operator on a weekly basis in accordance with the manufacturer's specifications. Technical data for the chain belt conveyor: Manufacturer Stadler Anlagenbau GmbH Typ chain belt conveyor KF 1800 Year of construction 2015 Belt speed 0,36 m/sec. Length feeding conveyor 7,000 mm Length elevating conveyor 14,500 mm Length goose neck 1,550 mm Grade 30° Nominal width 1,800 mm Effecting width 1,638 mm Height conveyor over all 7,745 mm Pit dimensions to conveyor belt 11,200 x 3,000 x 1,250 (l x w x h) Scope of delivery: The conveyor belt, the transverse distribution belt and the baling press are for sale, with bale chute but without wire pulling stations and without wire. Comments: The documentation (Manual, CE-declaration, electr./hydr.-drawings), are completely available. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors. Blodpsxb Dvvsfx Adxep

Condition: excellent (used), Year of construction: 2010, functionality: fully functional, Manufacturer: Kautex Maschinenbau GmbH Blsdexrdq Ijpfx Adxsp Model: KCC10-D Clamping force of blow molding machine: 120 kN Extruder type: E70 Screw diameter: 70 mm With equipment Fully functional, inspection possible by appointment!

Condition: new, Year of construction: 2025, functionality: fully functional, type of input current: AC, type of cooling: air, The universal laser marking system LAS 28 XLe from Systemtechnik Hölzer GmbH can be used for a very wide range of marking applications. With the integrated fiber laser you can mark almost all materials such as steel, carbide, aluminum and plastics. Depending on the requirements, the system can be equipped with a 20, 30 or 50 watt fiber laser. For permanent marking, the use of the laser is necessary in many industries. Bjdsxd Az Nepfx Adxjlp With the powerful laser software, texts, numbers, 2D codes, QR codes and logos can be realized with just a few clicks without extensive programming knowledge. Serial and article numbers are automatically incremented by the software after prior setting. In addition, the software can read data (variable information such as drawing numbers, project designations, etc.) from existing tables and automatically transfer them to predefined areas. The use of a hand scanner is also possible. The standard equipment includes integrated PC with Windows operating system and laser software. Optionally, the laser model LAS 28 XLe can be equipped with a rotary axis (3-jaw chuck) for marking cylindrical parts. Further options, such as lateral extension arms for marking long parts, movable Z-axis, drawer systems, etc., can be realized. Made in Germany Fiber laser 30 W, 20 W or 50 W - Laser class 1 - Wavelength 1064nm - Marking field size 150x150mm (optionally larger) - Signal light for displaying operating status - optional: rotary axis (3-jaw chuck) - optional: extraction system (incl. activated carbon filter) - optional: digital height measuring system - optional: autofocus system - EZCAD marking software in German / English - Pilot laser (simple preview, plain text preview) - Focus finder (simple focus adjustment) - max. component height approx. 300mm - Electrically adjustable Z-axis - Integrated PC with Windows operating system - Height-adjustable screen and keyboard support - Frame made of aluminum profile - Air-cooled - Door width approx. 700mm / door height (pass-through): approx. 400mm - 230V connection - Dimensions: approx. 900 x 800 x 1900 mm (LxWxH) with screen holder approx. 1500 x 800 x 1900mm (LxWxH) - Weight: approx. 120 kg

Condition: new, Year of construction: 2025, Plasma cutting machine for pipes and profiles Plasma cutting machine for cutting pipes and profiles. The cutting contour is defined and create by the software. The created CNC code can send to the machine via USB or network. The program can be easily choose via the 12"touch display. The automatic cutting process is started after manual insertion of the workpiece. - Tube length: max. 6000mm - for round tube up to OD = 150mm max - for square tube up to 101.6x101.6mm (4 "x4") max - maximum pipe weight 100KG per load - 4-jaw chuck - 1x automatic raw support - fully automatic cutting process - PC control with 12 "touch display - Data import via USB and network - Power consumption: 400V 3P 2KW - weight: 800KG Bljdpfxsgu Nmhe Adxep Made in Germany The pictures show you an older machine

Year of construction: 2024, condition: new, Universal testing machine H50TMCI / 900 Watt mechanical construction: according to DIN EN ISO 7500-1) 2 backlash-free ball screws, drive via AC servo motor, Fmax = 50 kN, stiffness 65 kN/mm 1 working area up to nominal load: working area width: 510 mm (optional widening: +240mm / +530mm) Bedpfxoiq Hxcs Adxjlp max. test stroke without test tools, adapter and KMZ: 1095 mm (optional extensions: +250mm / +500mm) Optional: conversion to floor model, required additional assembly: substructure table Travel speeds: Test speed 0.001 - 800 mm/min at full load Return speed 800 mm/min Force measurement: Measuring range: in the range 0.4 - 100 % of the nominal load class 1 (optionally class 0.5) (+/- 1 % of the displayed value according to DIN EN ISO 7500-1) Resolution of force measurement: +/-180,000 digits at 20ms integration time The machine is delivered with a factory test certificate. If, at the customer's request, a factory or DKD calibration is to be carried out at the installation site, this expense must be invoiced separately. Crosshead travel measurement: Incremental rectangular input with encoder monitoring, storage of crosshead position. Resolution of the crosshead travel measurement:

Condition: refurbished (used), functionality: fully functional, Year of construction: 2006, control type: PLC-controlled, degree of automation: semi-automatic, pipe diameter (max.): 60 mm, mandrel length: 6,000 mm, year of last overhaul: 2025, Equipment: CE marking, emergency stop, Mandrel Bending Machine S6006 ----- For producing dimensionally accurate tube geometries with bending radii of up to 1.5xD → Maximum bending capacity tube 60.3 x 4 mm (400 N/mm²) → Maximum bending capacity tube 60.3 x 2.6 mm (stainless steel) → Total connected load 5 kW → Tube feed length 6 m Robust and durable steel construction with a force-locked design—no torsion-prone structure such as a separated construction of the bending head and mandrel carrier. Maintenance-free electromechanical drive for the bending axis. The control system's touch display enables easy and intuitive programming and operation of the machine. After the tube is loaded, it is fixed by a chuck on the carriage. This ensures precise positioning of the tube, allowing the creation of dimensionally accurate geometries. Standard equipment also includes geometry verification before the bending process: If the bending process is started from the wrong position, the machine will not allow it. This prevents incorrect operation. Optional additional features offer more convenience and increase output and thus the efficiency of the system. Data transfer from the optional TBS-3D tube calculation software (PC version) is done via USB stick or via FTP access from the computer to the machine control. USB or LAN connector (RJ45) are standard. Existing tube geometries can be easily and quickly converted, e.g., via the STEP format. Standard equipment: Bedpfx Adsw Sr Ucsxslp → Electromechanical drive for bending axis 2.2 kW → Rotation speed 2.9 rpm (=17°/s) → Left-hand bending direction → Bending angle resolution 0.1° → Max. bending radius 200 mm → Bending shaft diameter 50 mm → Electronic length measurement ±0.1 mm → Electronic torsion measurement ±0.1° → Manual stop system (length overtravel stops) → Manual indexing system (15° increments for torsion) → Three-jaw chuck to clamp the tube in the carriage → External control panel PLC Control: → 10.1" touchscreen → ETH 10/100, X2X Link, USB → Foot switch operation → Data transmission via (W)LAN or USB → Material database Unique graphical programming: Simple geometries can be calculated directly at the machine. The control system calculates the feed and bending angle directly after entering length and angle values. Hydraulics: → Hydraulic power 3 kW → Hydraulic tube clamping with adjustable clamping pressure → Programmable early mandrel retraction Options (available as additional equipment): → Variable bending speed via frequency inverter or servo motors → Automatic tool retraction (manual or controlled) → Pneumatic chuck → Automatic mandrel lubrication → Pneumatic stop system (length + torsion) → Mobile version (with castors) → Radius extension Sample image shows a similar machine

Year of construction: 2024, condition: new, Universal testing machine H 5 TMNI ( L ) 250mm Extended mechanical construction: according to DIN EN ISO 7500-1 and ASTM E4 Bljdoiq Hxvspfx Adxep 2 backlash-free ball screws, brushless drive motor, Fmax = 5 kN, rigidity 9.4 kN/mm 1 work area up to nominal load: Working area width: 420 mm max. test stroke without test tools, adapter and KMZ: 1270 mm max. test area height (between lower fixed and moving crosshead) without test tools, adapter and KMZ: 1325mm Travel speeds: Test speed 0.001 - 1200 mm/min up to nominal load Return speed 1200 mm/min Force measurement: Measuring range depending on the force sensor used 0.4 - 100 % of the nominal load class 1 (optionally class 0.5) in accordance with DIN EN ISO 7500-1 and ASTM E4. Resolution of the force measurement depending on the integration time between: +/-160,000 and +/-900,000 digits. The machine is supplied with a factory test certificate. If a factory or DAkkS calibration is carried out at the installation site at the customer's request, this must be charged separately. Crosshead travel measurement: Incremental rectangular input with encoder monitoring, storage of traverse position Resolution of the crosshead travel measurement:

Condition: used, Year of construction: 2017, pipe diameter (max.): 80 mm, mandrel length: 4,500 mm, Mandrel bending machine S8004 ----- For the production of dimensionally accurate pipe geometries with bending radii of up to 1.5XD → maximum bending performance pipe 76 x 4 mm (400 N/mm²) → maximum bending performance pipe 60 x 60 x 3 mm (400 N/mm²) → maximum bending performance pipe 76 x 2.9 mm (stainless steel) → total connected load 7 kW → pipe length 4.5 mtr Robust and durable steel construction in a force-locking connection - no construction susceptible to torsion due to, for example, the split construction of the bending head and mandrel carrier. Maintenance-free electromechanical drive of the bending axis. The touch display of the control enables simple and intuitive programming and use of the system. After the pipe has been pushed on, it is fixed in the carriage by the chuck. This enables the pipe to be positioned precisely and thus the creation of dimensionally accurate geometries. The standard also includes checking the pipe geometry before the bending process: If the bending process is started in the wrong position, the machine does not give permission for this. This prevents incorrect operation. Optional additional features provide more convenience and increase the output and thus the efficiency of the system. Data is exchanged from the optional pipe calculation program TBS-3D (PC version) via USB stick or via FTP access from the computer to the machine control system. USB or LAN connectors (RJ45) are available as standard. Existing pipe geometries can be converted quickly and easily, for example, using the STEP format. Standard equipment: → Electromechanical drive of the bending axis 4 kW → Speed 2.9 rpm (=17°/sec.) → Bending direction left → Bending angle resolution 0.1° → Max. bending radius 200 mm → Bending shaft diameter 50 mm → Electronic length measurement ±0.1mm → Electronic twist measurement ±0.1° → Manual stop system (overtravel stops in length) → Manual locking system (15° in twist) → Three-jaw chuck for locking the pipe in the carriage → External control panel PLC control: → Touchscreen 10.1" → ETH 10/100, X2X Link, USB → Foot switch operation → Data transfer via network (W)LAN or USB → Material database Unique graphic programming: Simple geometries can be calculated directly on the machine. The control calculates the feed values directly after entering the length and angle and the bending angles. Hydraulics: → Hydraulic power 3 kW → Hydraulic pipe clamping with adjustable clamping pressure → Programmable early mandrel retraction Options (can be ordered as additional equipment): → Variable bending speed using frequency converters or servo motors → Automatic tool retraction (manual or controlled) → Pneumatic chuck → Automatic mandrel lubrication Blodettah Ropfx Adxjp → Pneumatic stop system (length + twist) → Mobile version (rollers) → Radius extension Pictures show new machine

Condition: good (used), Year of construction: 2014, functionality: fully functional, machine/vehicle number: H50KS, tractive force with load: 50,000 N, Universal testing machine, type H50kS up to 50KN for tension and compression Load cell 50KN 10KN 1KN and Windows software 8-9-10-or 11 for tension, compression, bending, shear etc., according to EN ISO 7500-1, ASTM E4 The H50kS is a universal testing machine developed according to the latest standards. The machine operates in accordance with the relevant radiation protection and safety directives in the EC. (EN 50081-1, 72/23/EEC, EN 61010-1) The maximum voltage within the machine is 48 volts. Special features - large, easy-to-read liquid crystal display with backlighting - Graphical or numerical display mode - alpha-numeric file input - speed range 0.001 to 500 mm/min. - high return speed 0.001 to 500 mm/min. - exact crosshead positioning - Robust load frame - Output report of results with mean value and standard deviation via printer - Large selection of test software under Windows for various standards - RS232 interface mode for use with computer system - Accuracy of load cell force display 0.5 % over the entire range - Displacement display accuracy 0.001 mm - Equipped with a force and displacement alarm system - 32bit motor controller - 20% digital weight blanking during load cell capacity check - Automatic motor alarm in case of over or under voltage and overheating Specifications: - Force measurement accuracy +/- 0.5 % of the displayed force in the range 2% to 100% - Accuracy of position measurement +/- 0.01 % or 0.001 mm - Speed accuracy +/- 0.005 % of the selected speed - Operating temperature 0 to 38°C - Humidity range 10% to 90% Technical data: - Two-spindle table model - maximum load 50kN in tension and compression - maximum stroke 1100 mm without clamping fixtures - for further details please refer to the brochure Bodpfx Aeq Ruw Nedxelp Dimensions: Height: 1613 mm width: 720 mm Depth: 500 mm Weight: 140 kg Connection: Machine: 50-60 Hz - 2000 W Power supply: 220/240VAC

Condition: new, functionality: fully functional, Year of construction: 2025, Manual Pipe Bender HRB-3D 850 for bending pipes and solid material up to a maximum of 12 mm Precise positioning and repeatable bending are ensured by three battery-operated digital displays that precisely show the bending angle, pipe feed, and pipe twist. Blsdottagdepfx Adxsp - 80 mm three-jaw chuck - Feed stop system - Feed length approx. 850 mm The manual pipe bender should be permanently mounted on a table or frame (not included). We would be happy to provide you with a detailed quote if you send us your complete company address, email address, and contact details.

Year of construction: 2024, operating hours: 4 h, condition: as good as new (ex-display), functionality: fully functional, machine/vehicle number: H2,5TMNI, Universal testing machine H 2,5 TMNI L Please always send your mail address. mechanical construction: Single spindle universal testing machine with backlash-free ball screw in C-frame design with spindle protection and brushless drive motor, Fmax = 2.5 kN 1 working chamber up to nominal load: Working chamber depth: 105 mm max. test stroke without test tools, adapter and KMZ: 1375 mm max. test area height (between lower fixed and moving crosshead) without test tools, adapter and KMZ: 1375 mm Travel speeds: Test speed 0.005 - 1200 mm/min up to nominal load return speed 1200 mm/min Force measurement: Measuring range depending on the force sensor used 0.4 - 100 % of the nominal load class 1 (optionally class 0.5) according to DIN EN ISO 7500-1 and ASTM E4. Resolution of the force measurement depending on the integration time between: +/-160,000 and +/-900,000 digits. Bjdpfx Adjmdn Troxolp The machine is delivered with a factory test certificate. If, at the customer's request, a factory or DAkkS calibration is to be carried out at the installation site, this expense must be invoiced separately. Crosshead travel measurement: Incremental rectangular input with encoder monitoring, storage of crosshead position. Resolution of the crosshead travel measurement:

Condition: like new (used), Year of construction: 2023, Mandrel Bending Machine S4501 ---- For the production of pipe geometries with bending radii from 1.5xD → Maximum bending capacity: pipe 42.4 x 3.25 mm (steel max. Re 240 N/mm²) → Maximum bending capacity: pipe 30 x 30 x 3 mm → Maximum bending capacity: pipe 42.4 x 2 mm (stainless steel max. Rp0.2 260 N/mm²) → Total connected load 3 kW → Pipe insertion length approx. 1.5 m Robust and durable steel construction. Maintenance-free servo drive for the bending, feed, and twisting axes. The control system's touchscreen display enables simple and intuitive programming and operation of the system. After the pipe is inserted, it is secured in the carriage by the chuck. This enables precise positioning of the pipe and thus the creation of dimensionally accurate geometries. The standard also includes a check of the pipe geometry before the bending process: If the bending process is started in the wrong position, the machine will not issue a release. This eliminates the risk of incorrect operation. Optional additional features provide greater convenience and increase output, thus increasing the efficiency of the system. Data exchange from the optional TBS-3D pipe calculation program (PC version) takes place via USB stick or network. Existing pipe geometries can be imported using the software. Standard equipment: → 1.5 kW servo drive for the bending axis Bledpfxotr U Hls Adxjp → Adjustable speed → Left-hand bending direction → Bending angle resolution 0.1° → Max. bending radius 120 mm → Bending shaft diameter 50 mm → Feed servo drive → Rotation servo drive → Three-jaw chuck for locking the tube in the carriage → Pneumatic tool retraction Hydraulics: → Hydraulic tube clamping with adjustable clamping pressure → Programmable early mandrel retraction PLC control: → 10" color touchscreen → ETH 10/100, X2X Link, 2xUSB → Foot switch operation → Data transfer via LAN or USB network → Material database Unique graphical programming: Simple geometries can be calculated directly on the machine. The control system calculates the feed values and bending angles directly after entering the length and angle. Power consumption: 400V 16A Dimensions: L: 2.3 m x W: 1m x H: 1.4m Weight: approx. 1200 kg

Condition: like new (used), Year of construction: 2018, functionality: fully functional, machine/vehicle number: STHP 80KN, total height: 1,320 mm, total width: 510 mm, total length: 200 mm, pressing force: 8 t, table width: 300 mm, overall weight: 110 kg, 1 Hydropneumatic press type STHP 80 kN Bmcbfntr with two-hand operation - floor model with and base frame Bjdpfxet Rhb Is Adxjlp The compact and handy table model has a hydropneumatic drive with pressure intensifier, which can increase the punching force by up to 5 times. The punching cylinder is pressurized with oil by the pressure intensifier during the working stroke and therefore has a purely hydraulic punching stroke. The return stroke is performed directly with compressed air. The adapter that can be screwed into the piston rod of the working cylinder makes it possible to install special tool holders.