Used Cross Carriage for sale (6,014)

Condition: used, Year of construction: 2009, conveyor belt, belt conveyor, transport belt, belt conveyor -Manufacturer: Grenzebach, conveyor belt 2 levels type EZT with guide rollers Iisdpfxetrhm Ae Aatof -Speed: frequency controlled -Drive: 2x SEW Eurodrive -Conveyor belt length: 1400 mm -Belt spacing: 410 mm -Cross carriage: roller spacing 1000 mm -Number: 2x conveyor belt available -Price per piece -Dimensions: 1450/1550/H920 mm -Weight: 358 kg/pc.

Year of construction: 2015, condition: excellent (used), functionality: fully functional, Technical specifications for the bale opening line for RDF, MSW, paper, and cardboard: Manufacturer: Cross Wrap Oy Ltd., Siilinjärvi, Finland Type: BO 4000 Year of construction: 2015 Number of bales opened: 674 Operating time: only 3 days, exclusively during the initial commissioning of the entire system upon new installation Opening time: approximately 45 seconds per bale Bale dimensions (W x H x L): 1100 x 1100 x 1400 – 1900 mm Max. bale weight: 2,000 kg System conveying height: 1,400 mm Max. system conveying width: 1,200 mm Material to be opened: RDF/MSW System availability: 98% Noise level of the bale opening line: 85 dB(A) Total connected load: 37 kW Iedpfezp H R Esx Aatsif Rated current: 125 A Control panel: SIEMENS SIMATIC HMI Touch Controller: SIEMENS S7 ET200S Installation dimensions: 8,463 x 2,890 x 3,960 mm (L x W x H) Scope of supply: Infeed conveyor: 3,500 x 1,200 x 1,400 mm Feed conveyor to the opener: 1,500 x 1,200 x 1,400 mm Bale opener (gripper with knife) Special equipment: Oil heating in the hydraulic oil tank Control cabinet heating Oil cooler for hydraulic unit Explanation for the short operating time: The entire Cross Wrap bale opening line, type BO 4000, was installed in 2015 at a municipal waste incineration plant. The reason for installing the system was to ensure that municipal waste could continue to be accepted, compressed, wrapped, and stored even during an operational disruption or maintenance of the incineration plant until the disruption was resolved. Subsequently, all the bales were to be opened again, and the waste fed into the normal incineration process. This worst-case scenario never occurred. The system was installed, commissioned, and then never used in normal operation. Only during the commissioning and initial operation of the entire system in 2015 were 674 bales opened over three days. The system is in very good condition and is immediately ready for operation. Due to restructuring measures in the incineration plant, the installation space of the bale opener was needed. This means that the complete line is now available for sale. Brief description of the bale opening process: The compressed bales are placed on the infeed conveyor from the side or from the rear using a forklift. To open the bales, they must be positioned horizontally to the conveyor with the wire or twine binding; otherwise, the bales must be rotated by 90° beforehand. The opening conveyor brings one bale at a time in front of the cutting unit. The grippers hold the wires or the twine binding. The rotating knife cuts the bale lengthwise. After that, the gripper returns to its starting position. The opened bale is now conveyed via the conveyor to the discharge chute and then falls onto the subsequent conveyor system. Remarks: New price of the complete system: €296,000. The documentation (operating manual, CE declaration, electrical/hydraulic circuit diagram) is complete. The system has been dismantled into transportable units, stored, and is available for inspection and loading in the short term. We assume no liability for the technical data or any potential errors.

Condition: like new (used), Range (depending on lighting conditions): up to 15 m Range with laser receiver: 30 m and more Leveling accuracy at 5 m: +/- 1 mm Self-leveling range: 4° +- 0.5° Iijdpfx Aaed Ecncjtef Accuracy of the horizontal line at 5 m: +- 1.5 mm Accuracy of the vertical line at 3 m: +- 0.75 mm Number of laser lines: 2 Weight: 485 g

Condition: excellent (used), Year of construction: 1997, Rip and cross saw REMA DMLK 30 Producer of REMA Machine model / type DMLK 30 Year of production 1997 Machine category Longitudinal and transverse saw Isdpfxsfv Hphs Aatoif Location Gorzów Wlkp. Conditions of delivery PERSONAL COLLECTION Cost of delivery Customer cover Startup type to be agreed Description Comments - after the technical review - very good condition - year of production 1997 TECHNICAL PARAMETERS: main engine 3.9 kW trolley length 1370 mm blade diameter 300 mm angle adjustment 0 - 45 " height adjustment cutting height max. 90 mm cutting width on the right side 885 mm ruler length 1350 mm ratchet extended receiving table two kinds of blade rotation speed 3700 and 5000 RPM The protractor visible in the photos is an additional option for PLN 400 net dimensions: length / width / height 135 x 85 x 135 cm weight ~ 320 kg

Condition: used, Year of construction: 2007, total width: 1,070 mm, total length: 9,000 mm, total height: 1,420 mm, Colour: Blue Weight: 1.500 kg - Year: 2007 - Documentation available: No - CE marking present: Yes - CE certificate present: No - Serial number: 48-2007-1403 - Main motor power [kW]: 5.5 - Max. cutting depth [mm]: 320 Isdszufv Repfx Aateif - Max. cutting height [mm]: 100 - Max. saw blade diameter [mm]: 500 - Arbor saw blade diameter [mm]: 30 - Table length [mm]: 5000 - Table width [mm]: 350 - Spindle speed control: Not applicable - Voltage [V]: 400 - Current consumption [A]: 10.3 - Fuse [A]: 16 - Power [kW]: 5.5 - Transport dimensions: 9000mm x 1070mm x 1420mm (l x w x h) - Transport weight [kg]: 1500kg - Transport packages [pcs.]: 3 Financial information VAT: The price shown is exclusive of VAT VAT/margin: VAT deductible for entrepreneurs Delivery and trade-in always possible for everything in the industrial sectors Yorick Diebels

Condition: new, Stromab Matrix F Automatic Fully Programmable Cross Cutting & Notching Machine A heavy duty optimising upstroke crosscut and notching machine, designed for programmable and repetitive cutting and notching from standard and / or random lengths of timber. The saw unit has a pneumatic upstroke action with variable speed control, The notching unit is independent of the saw and therefore allows for programming of the saw or notching either as separate program's or as one single job. The pusher / feed is fitted with a heavy duty rack and pinion drive feeding system for fast positioning giving a high level of repeat cutting accuracy. The saw unit and clamping area is totally enclosed by a clear hinged electrically interlocked hood that while giving the operator a clear view of the cutting area still gives complete protection. The infeed and outfeed tables are of all steel construction meaning even heavy sections or packs of timber can be processed. For additional operator safety the rear of the pusher system is guarded, while there is a full length safety pull cord on the front infeed table. Programming and entering of cutting lists is very simple through a colour touch screen controller with graphic representation of the cut pieces. The machine offers full optimisation and also has the added optional facilities of defect cutting and remote programming from PC or laptop with transfer vis USB key or network. Additional options also include - extended outfeed table and label printing. To date we have supplied over 250 Matrix saws in to the UK, with a number of customers installing several machines. Ijdpfx Aedy Hrdsatjif Saw unit Self braking saw motor 10hp Saw blade diameter 500mm Max cutting width 360mm ( refer to chart ) Max cutting height 135mm ( refer to chart ) Dust extraction 4 x 100mm diameter Milling Unit Self braking milling motor 5.5hp Pneumatic milling stroke with adjustable speed Max milling stroke 400mm Max milling width 100mm Max milling depth 60mm Dust extraction 2 x 125mm and 2 x 100mm Push feed system 3000 to 13000mm Precision rack and pinion drive to pusher with magnetic reading tape giving a high level of repeat cutting accuracy. Pneumatic rising of the pusher at the end of cutting cycle Piece length reading photocell Positioning speed 100m/min Positioning accuracy + /- 0.4mm Touch screen control unit Remote programming of cutting list via colour graphic touch screen controller - connection via USB key. - 6 optimising criteria - longest size, minimum waste, sequence, priority size, by volume or by value. - 1000 cutting lists - 10,000 lines per list. - Cutting list entered via controller key pad or via remote PC using PC or cable - Graphic description of the workpiece.

Condition: used, Rema DMGB-35 double cross-cut saw, including an outfeed conveyor belt, for cross-cutting timber on both sides. This machine was specifically used for cutting doors to size. Iiodpfx Aezryuveatef In its current condition, the cutting length is limited to 1,000 mm, but this can be extended. Technical data: - Belt length: approx. 1,700 mm + 2,700 mm - Cutting width: max. 2,500 mm - Cutting height: max. approx. 80 mm

Condition: used, Year of construction: 2010, - Perfect for surface finishing - Constant working height - Q/L/Q Fine/cross-sanding machine Manufacturer: Weber Type: KSF-3-1350 Year of manufacture: 2010 Technical data - Equipped with 3 sanding belts for high-quality fine, veneer, and high-gloss sanding. - With a constant working height Machine frame - Heavy-duty steel welded construction for mounting 3 sanding units - Constant inlet height of 900 mm - Control and sanding belt change side on the inlet side, on the left - Stepless feed speed of 3-18 m/min, frequency-controlled. - Vacuum version of the conveyor belt / with 1 vacuum blower 5.5 kW, and a vacuum channel up to the upper edge of the machine Unit 1: Cross-belt unit - Pressure pad belt with felt and graphite for long service life - ISD segmented pressure bar system with 11 mm workpiece detection and 44 mm pressure pad width - Workpiece-controlled sanding belt blowing device Unit 2: CBF combination unit - One grooved rubber contact roller 0 130 mm, rubber hardness 60 Shore - One cross-running flap band with separate drive 4.0 kw - ISA segmented pressure bar system with 11 mm workpiece detection and 22 mm pressure pad width (counter-rotating) - Workpiece-controlled oscillating sanding belt blowing device Unit 3: Cross-belt unit - ISD segmented pressure bar system with 11 mm workpiece detection and 44 mm pressure pad width - Workpiece-controlled sanding belt blowing device Operator terminal SIEMENS" MP 377 12" Multi-Panel - Graphical user guidance via 12" color display - Program memory with 300 programs - Setting of all parameters via program WEBER i-Touch control - One rotary knob for navigating through the most important functions WEBER AWDM - Automatic thickness adjustment at the machine inlet with start switch Overthickness - Selector switch at the machine inlet with the following functions: - Automatic lifting of the contact roller and the segmented pressure bars Iiodpfszuzctex Aatef - Feed stop ISA/ISD control - High-resolution workpiece detection in a 22 mm grid - Free loading of complex part shapes - Multiple loading with a small lateral distance - Sanding intensity individually adjustable at all edges - Sanding pressure adjustable via program ISA segmented pressure bar system (Unit 2) - Pressure pad movable in the longitudinal and transverse direction ISD segmented pressure bar system (Unit 1+3) As ISA, but additionally with - Separate adjustable pressure for the edge area (higher or lower) - Optionally only on the outer edge or outer and inner edges - Longitudinal and transverse edges or only longitudinal edges can be adjusted Workpiece blowing device - with WEBER ES system - Energy-saving, workpiece-controlled workpiece cleaning with single slider control WANDRES-Micro-Cleaning (single brush version) - Power sword brush with integrated micro-humidification of the linear brush (for optimal paint dust removal) Technical data - Working width: 1350 mm - Drive Unit 1 (frequency-controlled-Eco-Drive): 15.0 kW - Drive Unit 2 (frequency-controlled-Eco-Drive): 20.0 kW - Drive Unit 3 (frequency-controlled-Eco-Drive): 15.0 kW - Drive CBF: 3.0 kW - Drive vacuum blower: 5.5 kW - Drive feed (frequency-controlled): 3.0 kW - Drive height adjustment (frequency-controlled): 0.75 kW - Sanding belt speed (frequency-controlled): approx. 3-20 m/s - Sanding belt dimensions cross belts (W x L): 2x150x5100 mm - Sanding belt dimensions wide belt (W x L): 1370x2620 mm - Workpiece thickness (min./max.): 4-140 mm - Working height (constant): 900 mm - S

Condition: used, Year of construction: 2011, Cross-cut and rip saw Manufacturer: HOLZMA Type: HQP 11/16/56/LX Year of manufacture: 2011 Technical data - Combined saw unit with cross-cut saw unit, cutting length 1,600 mm, and rip saw, cutting length 5,600 mm - additional pressure cylinder - postforming unit - waste flap 1600 mm - clamping device for cross-cut saw, 2-finger - automatic ejector guide - roller conveyor designed for 1,300 mm width Iodezuyzzopfx Aatjif - second drive in the roller conveyor - 1 m shaking chute 550 mm (driven) - mobile CADMATIC control panel - cooling unit for individual saw - with vacuum loading system and outfeed table Note: The technical data and descriptions are a copy of the original order confirmation. The data is for informational purposes only and is not binding.

Condition: used, Comec FRO1000 cross-profile milling machine for the precise machining of cross-profiles and shaped millings on solid timber and wood-based materials. The robust construction and the sturdy milling unit ensure consistently precise profiles in both batch and single-piece production. Technical data: Ijdpfoztvxgox Aatsif - Working width: approx. 1,000 mm - Spindle diameter: 40 mm - Feed: Pneumatic

Condition: used, Fork carriage with hydraulic side shift + long forks, suitable for STILL model EFG 3.0/6004 Iiodpfx Aajztvuzjtof Technical data: - Fork carriage width: 1,100 mm - Fork length: 1,900 mm - Fork cross-section: 100 x 45 mm

Condition: used, Year of construction: 1999, total height: 1,800 mm, total length: 5,700 mm, total width: 2,300 mm, Colour: White Weight: 2.000 kg Ijdpjzmxvzjfx Aatsif - Year: 1999 - Documentation available: No - CE certificate present: No - Serial number: 10.7488 - Main motor power [kW]: 6.3 - Max. saw length [mm]: 5200 - Max. saw width [mm]: 360 - Max. saw blade diameter [mm]: 600 - Input table length [mm]: 5200 - Output table length [mm]: 3300 - Options: Automatic pusher system - Transport dimensions: 5700mm x 2300mm x 1800mm (l x w x h) - Transport weight [kg]: 2000kg - Transport packages [pcs.]: 2 Financial information VAT: The price shown is exclusive of VAT VAT/margin: VAT deductible for entrepreneurs Delivery and trade-in always possible for everything in the industrial sectors Yorick Diebels

Condition: used, Dimter OptiCut 700 automatic optimising cross-cut saw (sliding saw) for cutting very wide timber to size according to defects (marked with fluorescent chalk) and length. Technical data: - Cutting height: max. 120 mm - Feed length: max. 5,500 mm - Cutting width: max. 700 mm - Saw blade diameter: max. 700 mm Iisdpfx Aaszryvastef

Condition: used, Weinig OptiCut 260 optimisation cross-cut saw for cutting timber to length and removing sections with defects (marked with fluorescent chalk). The separate measuring station records the lengths and marked defects. Technical data: Ijdpfxjzryups Aatjif - Cutting height: 260 mm - Saw blade diameter: 500 mm - Inlet length: 400 – 6,300 mm - Inlet thickness: 12 – 80 mm - Feed rate: max. 250 m/min - Cycle time: approx. 1 sec - Saw motor: 7.5 kW - Marking station: 5,000 mm - Outfeed conveyor: 7.5 m with 3 pneumatic ejectors - Control system: OptiCom Pro - Year of manufacture: 2022

Condition: used, The EMMEGI wood and aluminium cross-cut saw is designed for cutting to length and mitre cuts: swivelling Technical data: - Motor: 0.55 kW / 220 V Iodpjzryuiefx Aatoif - Cutting height: approx. 50 mm - Cutting depth: approx. 80 mm

Condition: used, d1 = 35 mm Iiodpfx Ajzrxqpoatef d2 = 27 mm (spanner width) Technical data: - Overall length: 195 mm

Condition: used, Weinig 40x40 cross clamp for securing pressure rollers from above in Weinig planers. Technical data: Iisdpfx Aszrxpxjatjf - Overall length: 215 mm - d1 = 30 mm - d2 = 27 mm (spanner width)

Condition: used, Weinig 45x45 cross clamp for securing pressure rollers from above in Weinig planers. Iiedpfx Aezrxn Usatsf Technical data: - d1 = 35 mm - d2 = 27 mm (spanner width) - Overall length: 115 mm

Condition: used, Weinig 40x40 cross clamp for securing pressure rollers from above in Weinig planers. Technical data: - Overall length: 110 mm Isdpjzrxn Isfx Aateif - d1=30 mm - d2= 27 mm (spanner width) - Available: 3

Condition: used, Built in 1998 CNC motor-controlled Iisdjzrxlgopfx Aatof Technical data: - Quantity: 2

Condition: used, Year of construction: 2016, chainsaw equipped with a chain sharpener, chain feed mechanism, and output with ejectors high-speed chainsaw Iodjzb Rhmepfx Aatjif

Condition: used, Year of construction: 1995, preparation mat Iiedpfxezhrc Ro Aatof infeed mat recovery transfer GRECON Opticut 350 chainsaw

Condition: good (used), Suspension clamp, clamping sleeve, flange clamp, pipe connector, flange clamping piece, cross clamping piece, cross clamp connector, cross clamp -Manufacturer: Rose Krieger, 4 pieces cross clamp connectors, aluminum cross clamp, round tubes -Type: Size 50/25 mm Iiodpfeznu Agjx Aatef -Submission/Price: complete -Dimensions: 135/65/H65 mm -Weight: 0.6 kg/pc.

Condition: used, Year of construction: 2016, total height: 1,600 mm, total length: 14,100 mm, total width: 1,600 mm, Colour: Grey Weight: 2.500 kg Iiedpfxewnh N Ne Aatof - Year: 2016 - Documentation available: Yes - CE marking present: Yes - CE certificate present: No - Serial number: 6237 - Max. saw length [mm]: 6500 - Max. saw width [mm]: 400 - Max. saw height [mm]: 135 - Max. saw blade diameter [mm]: 500 - Arbor saw blade diameter [mm]: 30 - Input table length [mm]: 6700 - Output table length [mm]: 6000 - Options: Automatic pusher system - Voltage [V]: 415 - Current consumption [A]: 20 - Transport dimensions: 14100mm x 1600mm x 1600mm (l x w x h) - Transport weight [kg]: 2500kg - Transport packages [pcs.]: 4 Financial information VAT: The price shown is exclusive of VAT VAT/margin: VAT deductible for entrepreneurs Delivery and trade-in always possible for everything in the industrial sectors Yorick Diebels

Condition: used, various tool changing consoles / die loading arms available: 070022 GUETHLE-SWT CT 16/1600 (16 t / 1600 mm) with support leg (2x) 180006 GUETHLE-SWT CT 6/2700 (6 t / 2700 mm) with support leg (2x) 210008 GUETHLE-SWT CK t / 1000 mm) (2x) 210009 GUETHLE-SWT CK t / 1000 mm) (2x) 180010 unknown (2 t / 1500 mm) with support leg (2x) 190002 GUETHLE-SWT CT t / 1000 mm) with support leg (2x) 220019 GUETHLE-SWT CT 2/1000 (2 t / 1000 mm) with support leg (2x) 180002 GUETHLE-SWT CK 2/800 (2 t / 800 mm) (2x) 090054 GUETHLE-SWT CS 2/800 (2 t / 800 mm) swivelling (2x) 180003 GUETHLE-SWT CK 1/800 (1 t / 800 mm) (2x) Ijdjzrpn Ejpfx Aatsif 230001 Hydrap (1 t / 800 mm) (2x)