Used Aggregate for sale (860)

Condition: used, Year of construction: 2004, Used machine Year of manufacture: 2004 with gluing unit for hot-melt adhesive granules Glue reservoir located below the glue roller Glue application to the workpiece via glue roller in both co-rotating and counter-rotating modes automatic edge magazine for coil material and fixed lengths Pressure zone with pneumatically-driven main pressure roller and special post-pressure rollers to compact the upper and lower glue joint Centrally adjustable upper pressure Central manual chain conveyor lubrication Control panel at machine infeed End trimming unit (saw aggregates) for front and rear edge overhang with high-precision linear guides 2 motors, each 0.18 kW Swivel range for straight and bevel cutting 0–15 degrees Flush-milling unit, top and bottom, with vertical and horizontal tracing Swivel range 0–15 degrees with 2 milling motors, each with replaceable insert cutter combinations (straight/radius) Digital counters enable rapid and precise, i.e., repeatable, settings Rcedpfx Ajxya Rtja Ejk Two-point pneumatic adjustment for upper and lower milling motors Scraper unit for finishing processing with horizontal/vertical tracing Support table extendable up to 350 mm Integrated section control for contactless operation of processing functions. Settings via keyboard and LED display Workpiece thickness: 8–50 mm Edge thickness: 0.4–3 mm Feed speed: approx. 9 m/min Connected load: 4.1 kW Compressed air connection: 6 bar Weight: approx. 750 kg Machine length: 3,150 mm Availability: short term Location: Flörsheim

Condition: used, Year of construction: 2004, double end profiling machine for the door and windows production working width 4000 mm 3 aggregates on each side 1 x saw 2 x vertical miling aggregate - spindle stroke 800 mm! long side profiling machine with 16 spindles machine comes with a lot of spare parts! further technical data on demand Advise used machines: • Technical data without obligation, mistake and intermediate sale reserve. • Price is considered ex-location price • All articles or machines are bought as seen without any entitlement on warranty. Rjdpfx Ajdfx Hcja Eeck • It is left to the choice of the buyer to view the machines before at its location. • Special arrangements are possible but only valid in written form. (We answer your inquiries only with stated address + telephone number!)

Year of construction: 2022, operating hours: 503 h, condition: used, Serial number: 32228478-00520-0xxxx Please contact ATS Norway for more information Please provide reference number upon request: 20427 Specifications: - 2022 model - 503 hours - Lifting capacity of 150 kg - Aggregate Rjdpfxowi Rkrs Aa Ejck - Vacuum - 8.5 kW - Forks - Rubber tracks - Ready for delivery Description: We have a 2022 150 DA silent xl Vacuum lifter for stone slabs for sale. The machine works as it should and only has 503 hours on the counter. Efficient vacuum lifter that makes the job much easier for the gardener who will carry out the job. Ready for delivery Hours: 503 Own weight: 1689 Kw: 8.5 Model: 150 DA silent xl Vakuumløfter til steinheller. SE VIDEO

Condition: used, maximum load weight: 27,284 kg, overall weight: 36,000 kg, axle configuration: 3 axles, first registration: 10/2014, loading space length: 13,500 mm, loading space width: 2,470 mm, loading space height: 2,650 mm, total width: 2,550 mm, total height: 4,000 mm, Year of construction: 2014, Equipment: ABS, SCHMITZ CARGOBULL SKO 24L DOUBLE-DECK SCHMITZ COOL TKM LIFT ----VEHICLE HISTORY • Single owner • German vehicle • Video available upon request ----VEHICLE FEATURES GENERAL • Only the left portal door is damaged, the frame is intact! • 3-axle • SP (safety inspection) valid until: 04/2026 • TÜV: renewed BODY • Double-deck • Interior dimensions: • Length: 13.5 m • Height: 2.65 m • Width: 2.47 m REFRIGERATION UNIT • SCHMITZ refrigeration aggregate • SCHMITZ COOL TKM Rcsdpfx Aex Dznhea Esk • Year of manufacture: 2014 • Refrigerant: R404A (amount: 6.5 kg) • Diesel operating hours: 4738 h • Mains operation: 84 h AXLES / CHASSIS • Schmitz axles • ALCOA rims • Axle 1: lift axle • Full air suspension • Disc brakes • Tires: 385/65R22.5 • WABCO braking system EQUIPMENT / MISCELLANEOUS • 1 tool/storage box • Spare wheel holder ----IMMEDIATELY AVAILABLE! * EXPORT SALES ONLY WITH DEPOSIT MIN. €500 - €2,000 ----EXPORT CUSTOMS CLEARANCE EXW IN 10 MINUTES (AUTHORIZED EXPORTER) 5 DAYS, 30-DAY PLATES, AND 17-21 DAYS AUSTRIAN PLATES EURO 1 VEHICLE RESERVATIONS ONLY VIA EMAIL FUNCTION ORAL RESERVATIONS ARE NOT VALID! For sales to the EU and third countries, a deposit of at least €500.00 / €1,000.00 is required. Subject to changes, errors, and prior sale! More vehicles can be found on our homepage: Sale exclusively in accordance with our General Terms and Conditions – see homepage Important Note – Important Information: Despite careful verification of all details presented in our listing, errors may occur. This may be due in part to transmission errors in some platform providers’ systems. Therefore, all information is supplied without warranty and does not constitute a legal claim. Legal Notice: This sales advertisement does not constitute an offer within the meaning of §145 BGB (German Civil Code). Rather, it is for information purposes only in the course of contract initiation. The information provided here is without guarantee and does not represent warranted characteristics.

Condition: used, Year of construction: 2015, functionality: fully functional, BIESSE Edge Banding Machine AKRON 1440-A Automatic single-sided edge banding machines for gluing and processing straight edges with roll material (melamine, PVC, ABS, veneer) and strip material (solid wood, laminate, sliced veneer, etc.) • NC control with touch display • Automatic start of aggregate motors • Direct selection for second pass • Operating data acquisition • Software-guided maintenance TECHNICAL DATA Workpiece thickness 10-60 mm Workpiece thickness with MFU aggregate (depending on profile) 10-35/60 mm Edge height 14-64 mm Edge thickness – roll material 0.4-3 mm Edge thickness – strip material (*) 0.4-10 (12) mm Workpiece overhang 25 mm Minimum panel length 140 mm Minimum width (at 140 mm length) 85 mm Minimum width (at 250 mm length) 50 mm Feed speed 12 m/min Dust extraction* 8x connection Ø100 mm Compressed air connection 7 bar Glue pot capacity 2 (approx.) kg * Depending on selected aggregates. - GLUING UNIT VC-511 Applies the hot-melt adhesive to the workpiece, feeds the edge to the workpiece, automatically cuts it from the roll, and presses it onto the workpiece, guaranteeing perfect positioning. - END TRIMMING UNIT IN-801 For trimming the front and rear edge overhangs with 0° to 15° angle. - 2-MOTOR MULTIFUNCTIONAL PROFILE MILLING UNIT AR02 E For corner rounding and profile milling of workpiece edges made of synthetic material up to a thickness of max. 3 mm. JOINTING CUTTER UNIT RT02 Joins the workpiece before glue application. Equipped with two 1.8 kW high-frequency motors at 12,000 rpm. SCRAPER UNIT RB02 For post-processing thick PVC/ABS edges. FLAT SCRAPER RC02 Aggregate for removing excess glue in the edge-to-panel area. Equipped with tracing rollers and a flat knife with engagement control. BUFFING UNIT SZ02 For cleaning and buffing the workpiece edge using fabric polishing discs. The unit automatically adapts to the workpiece thickness. ANTI-ADHESIVE SPRAY UNIT ADZ02 Precision application of anti-adhesive using injectors activated by numerical control. KIT PRO-GLUE The PRO-GLUE kit includes the following components: • TEKNO-GLUE system for optimal gluing through: - controlled pressure of the glue roller - automatic disengagement in case of feed stop - automatic ON/OFF of the glue unit • REVERSE system to switch the glue roller for co- or counter-rotation Rcsdpexzb Iiefx Aa Eek Electrical and mechanical preparation for the use of special glue pots for POLYURETHANE glue with machines equipped for EVA gluing. NC Axis for Fine Trimming Unit Kit for the automatic adjustment of tracing rollers and tools to match edge type and thickness. Adjustment takes place via the control system. Pair of multiprofile cutters for the fine trimming unit: 25-degree bevel, radius 2 mm + radius 1 mm plus straight profile for solid wood. NC Axis for Profile Milling Unit Kit for automatic adjustment of the tracer to match the edge thickness. Adjustment takes place via the control system. Function for processing only on the corners. NC Axis for Scraper Unit Kit for automatic adjustment of tracing rollers and tools to match edge type and thickness. Adjustment takes place via the control system.

Condition: excellent (used), Year of construction: 2008, functionality: fully functional, workpiece length (max.): 6,175 mm, workpiece width (max.): 1,550 mm, workpiece height (max.): 300 mm, spindle motor power: 18,500 W, Homag CNC Machining Center BAZ 211/60/K Venture 21 XXL with 6 m working length, PowerEdge edge banding unit, renewed vacuum pumps, Windows 10, and WoodWOP 8.1, in very good condition: – Workpiece length 6000 – 6175 mm – Pendulum processing 2375 – 2550 mm – Workpiece width 1400 – 1550 mm – Maximum workpiece thickness 300 mm – Working height 950 mm (underside of workpiece) – Modernization I 2023: – 2 new rotary vane oil-lubricated vacuum pumps – Capacity 2 x 63 m³/h = 126 m³/h – Retrofit kit for separate cooling unit for main spindle – Modernization II 2024: – New machine PC with Windows 10 operating system – Upgrade to WoodWOP 8.1 – 4-axis CNC machining center – K console table – 10 consoles incl. front stops – 6 rear stops – 6 lift rails – 2 side stops each left/right/mirrored – 2 pneumatic connections per machining position – 2 vacuum connections for templates – C-axis with aggregate and electronic interface – Safety device with anti-slip mats – Main spindle 18.5 kW vector controlled – Liquid cooling for main spindle – 10+18-position disc tool changer: – 10-position disc changer moving with main spindle – 18-position disc changer moving with X-support – MPU drilling head 30 spindles V20 / H10 / S360° – MultiProcessingUnit with C-axis +/- 185° – 20 vertical high-speed spindles – 10 horizontal spindles – Grooving and separating saw 200 mm – PowerEdge 360° edge banding unit – Pickup station moving with X-support – Edge thickness 0.4-3 mm – Max. edge height 65 mm – 360° edge banding with butt joint – Pre-trimming station and single roller for PowerEdge – Hot air nozzle for edge banding unit – Combined flush trimming and finishing unit WD 60 mm – Flush trimming of edge overhangs – Finishing pre-milled edges – For use in main spindle – Probing for compensation of workpiece tolerance – 2 WPL radius cutter heads – 2 profile cutters for finishing unit – C-axis extension for Flex-5 unit Rodpfx Asx Dzbzoa Ejck – 10 LED position display systems for consoles – Optical LED display system – For positioning clamps and consoles – 4-fold configuration with 2 x 2 clamping positions – Separate vacuum systems – Detachable console for adjustable side stop – 2 additional side and longitudinal locating pins – 2 additional clamping consoles 1300 mm – 2 additional side and longitudinal locating pins – 2 additional lift rails for console table – 12 vacuum clamps 160x115x100 mm – 10 vacuum clamps 125x75x100 mm – Saw/drill unit with 2 spindles for tool changer – Saw blade diameter up to 240 mm – Side wall safety fence (left) – Rear safety fence – Side wall safety fence (left) – Year of manufacture 2008, single owner, very well maintained – Machine serviced regularly – No maintenance or repair backlog, no major defects – For sale ex location Karlsruhe / Southern Germany – Machine is still connected and fully operational – Inspection and trial run possible by arrangement

Year of construction: 1994, condition: excellent (used), CNC Morbidelli Author 503 The machine is efficient, working. After a major renovation. Technical data Year of manufacture: 1994 Tria 7500 control system Machining area: x=2890mm, y=900mm, z=80mm Milling aggregates: 2 pcs. with ISO 30 handle - 7.5kW with MK2 handle - 5.5kW revolutions: 1200-18000 rpm vertical drills: 18 pcs. horizontal drills: x axis - 4 pcs., y axis - 2 pcs. sawing unit 8 traverse beams vacuum pump 69m3/h connection power: 21kW Rcedpfxskl Envj Aa Esk weight; 3000 kg DTR, documentation, programming manual, diagrams.

Condition: used, Year of construction: 1985, edge thickness 0,4 - 12 mm work piece thickness 10 - 55 mm work piece length min 160 mm work piece width min 65 mm feed speed 13 m/ min compressed air 7 bar machine length 5420 mm weight 1950 kg glue pot with quick melt system glue application roller wit left and right turning edge magazine for PVC and strips motor height adjustment for pressure beam pneumatic pressure rollers for edge magazine control panel, rotatable all aggregates in-line controlled cutting milling combination with 2 aggregates, 1st aggregate straight, 2nd aggregate radius and phase milling tool draw blade buffing unit central lubrication for transport chain quick change system edge control system with error msg IR heater CE Rcodec Tmygspfx Aa Eok Advise used machines: • Technical data without obligation, mistake and intermediate sale reserve. • Price is considered ex-location price • All articles or machines are bought as seen without any entitlement on warranty. • It is left to the choice of the buyer to view the machines before at its location. • Special arrangements are possible but only valid in written form. (We answer your inquiries only with stated address + telephone number!)

Condition: used, maximum load weight: 37,600 kg, overall weight: 41,000 kg, axle configuration: 3 axles, first registration: 06/2024, next inspection (TÜV): 09/2026, total width: 2,550 mm, Equipment: ABS, You can find our complete vehicle inventory, including immediately and short-term available vehicles, on our website. Excerpt from the equipment. Full equipment list available on request. Chassis * Double-T longitudinal beams welded with cross members, front construction height: approx. 147 mm (including fifth wheel plate) * ‘Compact rear’ chassis version * Interchangeable 2-inch king pin, single position, front overhang: approx. 570 mm * Container rails made of rectangular tube, approx. 200 x 120 x 8 mm * Reinforcements at the approach slope * Fixed external steel rear impact guard * Rear underrun protection in accordance with EU regulations * Side guard device in accordance with EU regulations * Side protection device approx. 460 mm high * Full Quick-Lock package – lockings at every possible position – theft-protected locking system * Container locks for securing the following containers: 1 x 20' container, rear flush * Length from king pin to rear edge of vehicle: approx. 6,620 mm Support Equipment * Two mechanical landing gears, 2 x 12 t, half-round with base plate, brand: Jost * Operation of landing gears on one side, on right side in direction of travel Axles/Aggregates * 3 axles, each with 9,000 kg load capacity * Wheelbase: approx. 1,410/1,310 mm * KRONE axles with air suspension and disc brakes, ET 120 * Aggregate spacing = approx. 4,625 mm * Brake discs approx. 430 mm in diameter * Optional warranty extension on the KRONE axle: 6 years with unlimited mileage for on-road use within the EU. All wear-related parts: 3 years construction and manufacturer warranty, excluding normal wear. Applies to EU 2014, Norway, Switzerland, Turkey * Fully automatic, load-dependent electronic lift axle control for 1st axle * Manual function via operating console for forced lifting (=start-up aid per Directive 97/27/EC) and forced lowering via rotary switch * Preparation of lift/trailing axle(s) for operation from the tractor unit (installation in tractor not included), per selected electrical connections: - Lighting, for activation via Contact 6 of the 7-pin auxiliary connector (ISO 3731) - and/or Contact 12 of the 15-pin connector (ISO 12098) - and/or Contact 8A of the VBG connector * With lift and lowering facility, including automatic ride height reset Tyres (rims) * 6 pieces, 385/65 R 22.5 * No spare wheel, tread: M+S (mud + snow) * Wheel nuts with protective caps Mudguards * Plastic wheel covers * Splash protection in accordance with EU regulations Brakes * Braking system conforms to ECE Regulation 13 (including vehicle stability function) * Spring-loaded parking brake * Diagnostics via ISO 7638 connection (EBS supply cable) * Brake line connections below upper edge of beam * 4 wheel chocks with holder * Standard air connections ISO 1728 (Palm) * Lightweight alloy air tanks * Brake system manufacturer: Wabco Note: The trailer must only be towed by tractor units that ensure correct ABS function! * EBS system, 2S/2M, 2 sensors on one axle Lighting Rcodpfx Aaexgk U Aj Ejk * Lighting and signal system per UN ECE Regulation No. 48 * 2 marker lights with rubber arm, LED version * Electrical connections below upper edge of beam * LED side marker lamps with directional indicator (flashing function) * 24 volt, front 7-pin socket DIN ISO 1185 * 7-pin socket DIN ISO 3731 at front, for auxiliary functions * Additionally, front 15-pin socket DIN ISO 12098 Note: Connector pins (2 x 7-pin and/or 15-pin) per ISO 1185/3731 and/or ISO

Condition: good (used), Hydraulic motor, oil motor, hydraulic pump -Manufacturer: Danfoss, hydraulic motor -Type: OMP 50 151-0020 6 -Hole spacing: 106 x Ø13 mm -Shaft: Ø25 x 45 mm -Number: 12x aggregate available -Price: per piece Rcsdpfx Ajwldn Noa Ejk -Dimensions: 190/130/H125 mm -Weight: 5.9 kg

Condition: good (used), Year of construction: 1990, functionality: fully functional, machine/vehicle number: 712, feed length X-axis: 3,200 mm, feed length Y-axis: 900 mm, feed length Z-axis: 300 mm, Robust cnc machine with 3 mi aggregates and rotating 4 axis. Rcedsufghhspfx Aa Ejk

Condition: used, maximum load weight: 175,620 kg, overall weight: 219,000 kg, axle configuration: > 3 axles, first registration: 01/2002, Equipment: ABS, STHP 8 (3 + 5) 8 units of hydraulic BWP pendulum axle assemblies with remote control. Technically permissible gross weight 219,000 kg Technically permissible payload 175,620 kg Hydraulically suspended, 8-axle steered Goldhofer low-bed heavy-duty trailer type STHP 8 (3+5), consisting of 4 heavy-duty modules with a detachable gooseneck and extendable excavator low-bed section up to 5 meters, featuring 4 wheel recesses, ABS, technically permissible payload up to 175,620 kg. Consisting of the following 4 separate heavy-duty module parts: 1st module: Hydraulic universal gooseneck type STH/ST Year of manufacture: 2002 Can be combined with heavy-duty module undercarriages, drivable loading platforms. Unladen weight approx. 5,900 kg Permissible front fifth wheel load: 35,000 kg Length approx. 4.10 m Fifth wheel height approx. 1.30 m King pin 3.5" pin Removable aluminum side walls Fully hydraulically adjustable 2nd module: Goldhofer THP/ST3 3-axle heavy-duty module First registration: 14.11.2001 As a single module, technically permissible total weight: 108,000 kg, technically permissible axle loads: 36,000 kg at 5 km/h possible. Unladen weight: 10,350 kg As a single module, technical payload up to 97,650 kg at 5 km/h possible. 8 hydraulic pendulum axles, 24 wheels, tire size: 215/75/R17.5 Axle load: 25 t at 20 km/h Vehicle width: 3 meters Axle spacing: 1.5 meters Max. steering angle: ±60° Integrated into chassis: hydromechanical dual-circuit all-wheel forced steering with a maximum aggregate steering angle of 60°, integrated hydraulic oil tank Optimized bolt-lug coupling at front and rear for longitudinal combinations Single-tired pendulum axle assemblies with a total of 8 wheels per axle line Hydraulic axle compensation +/- 300 mm, hydropneumatic gas pressure suspension Hydraulic steering for all axles BPW axles with drum brake and ABS, technically permissible axle load of 34 t at 5 km/h 3rd module: Extendable low-bed heavy-duty module - Excavator bridge Year of manufacture: 2002 Internal dimensions approx. 7.50 meters long, 3.00 meters wide, loading height 0.40 meters Construction height 350 mm Extendable by approx. 5.00 meters - telescopic 4 wheel recesses with drive-on module at the front Construction height in wheel recess area approx. 150 mm Load capacity up to 80 t in low-bed and 175.6 t in overall STHP8 (3+5) module possible. Unladen weight 11,900 kg Front and rear hydraulic bolt-lug coupling with claw coupling adapter 4th module: Goldhofer THP/ET5 5-axle heavy-duty module First registration: 04.01.2002 Technically permissible total weight: 115,000 kg, technically permissible axle loads 23,000 kg at 5 km/h possible Unladen weight: 14,200 kg Technical payload up to 100,800 kg possible. Single-tired hydraulic pendulum axle assemblies with 4 wheels per axle line, 20 wheels (tire size 285/70 R 19.5) Hydraulic axle compensation +/- 300 mm, hydropneumatic gas pressure suspension Hydraulic steering for all axles Remote control for steering axles 5. Notes: With the 4 heavy-duty modules, up to 3 different tractor combinations are possible! Payloads change depending on the configuration. For the special low-bed combination, a current manufacturer's certificate from Goldhofer is available. The low-bed trailer can be tested at our facility. Price NET excluding 19% VAT. All information without guarantee. Subject to errors and prior sale. Internal vehicle number: 2285 Rcodpfx Aaexwgngo Eok

Condition: new, PROTON P-V LINE  PROTON equipment offers the right solution to recovering and conveying of blast medias, powders, plastic pellets, grains, sands, aggregates and other bulk metarials in both cleanup and material transfer functions. The main type of industry using our equipments are blast cleaning companies, shipyards, tank cleaning companies, metallurgical plants and steel mills, foundries, power plants, cement industries, chemical industries etc..   Rsdpfx Aajghbkyo Ejck The dust in the air is collected by a Vacuum Cleaner and the grit in the Stock Silo by its separator. Especially in inaccessable or enclosed areas such as storage tanks, box girder constructions, tank internals at shipyards etc., the equipment offers great savings in time and manpower.  A PROTON Vacuum system cuts costs by reducing cleanup time and reclaiming valuable materials.  This versatile vacuum system can be used to pick up any material that will flow through a hose.  With its long reach and powerful suction, PROTON cleans out tanks, pipes. There are 2 types of stock silos, Cylindrical and Square, having 2 floors. Technical Specifications for standard machines: VC Unit’s cost-cutting power has been proven hundreds of times. In fact, most VC units pay for themselves in less than 3 months through reduced labour costs and reclaimed materials. Units are available with capacities up to twelve tons per hour, conveying distances up to 330’’(100m),and motors with 7,5 kW-90 kW (3,98m³/min-72m³/min). Performance data for air (p₁=1,0 bar, t₁=20 °C, ρ=1,2 kg/m³) The heart of the PROTON VC is a very robust AERZEN blower made in GERMANY. All sets include the following equipment: - Suction Hose (rubber-wired) - Suction Hose for connection between Vacuum Unit and Hopper - Suction Nozzle - Cam-lock and clamp Connections - Cartridge Filter (spare) - Oil for Blower (spare) - Manometer (spare) - Phase Protection Relay - all necessary fasteners

Condition: new, Wide belt sanding machine for calibrating and fine sanding Working width mm 1,100 Min/ Max. working height mm 4/ 170 Sanding belt width mm 1,115 Sanding belt length mm 2,150 Gear motor kW 2.2 Feed speed m/min variable Infeed and outfeed support rollers for long and short workpieces Oscillating belt cleaning 1st unit Oscillating belt cleaning 2nd unit Oscillating belt cleaning 3rd aggregate 10” touch screen control panel “eye-S” 1. Aggregate steel roller 2. Aggregate rubberized calibrating roller 85SH 3. Aggregate combi-aggregate pneumatic seg. sanding pad /rubberized sanding roller 35 SH Motore power 1st unit kW 18.5 Motor powert 2nd & 3rd aggregate kW 18.5 Version "B" for RRCS with: Pneumatic switching on and off 1st aggregate Pneumatic switching on and off 2nd aggregate Pneumatic switching on and off 3rd aggregate "MESAR" with elastic segmented sanding pad Pneumatic switching on and off of the sanding pad unit electronic adjustment of the working height Rsdpfsitvkuox Aa Esck SPECIAL PRICE! IMMEDIATELY AVAILABLE

Condition: used, Technical details: number of spindles: 15 Stück number of stations: 8 Stück control: PS 2000 weight of the machine ca.: 17,0 t total power requirement: 83,0 kW dimensions of machine: LxBxH: 2400x2800x2800 mm dimensions electric cabinet: Nr.1:LxBxH: 1000x850x2350 mm dimensions electric cabinet: Nr.2: LxBxH: 1250x650x2230 mm dimensions electric cabinet: Nr.3: LxBxH: 650x600x1700 mm dimensions electric cabinet: Nr.4: LxB.H: 1000x500x1350 mm space requirements approx. LxWxH: 5,0 x 6,2 x 3,8 m TRANSFER MACHINE with 3 work station and 15 drill & mill spindles for example the production of a high quantity of armatures Other technical information about the machine: - workpiece carrier: workpiece holding barrel Ø 800mm for 8 work piece - clamping station, cycle time of 10 sec. - drilling and milling unit: SK 40 intake; spindle stroke 125 mm; standard feed rate 1m/min; rapid traverse feed rate 4m/min; RPM max. 2240 rpm - right 3x drill-& mill spindle, 1x thread cutting spindle, 1x U-axis such as radial 2x drill-& mill spindle slideable, 1x thread cutting spindle slideable and 2x U-axis slideable - left 3x drill-& mill spindle, 1x thread cutting spindle, 1x U-axis such as radial 2x drill-& mill spindle slideable, 1x thread cutting spindle slideable and 2x U-axis slideable - 1.Thread-cutting unit: SK 40 Intake; Quill Ø 125 mm; quill-stroke 125mm; RPM 35.5 - 900 rpm; right/left - 2.Thread-cutting unit: SK 40 Intake; Quill Ø 125 mm; quill-stroke 80mm; RPM 45 - 560 rpm; right/left Equipment: - 2 hydraulic aggregate - chip conveyor - belt filter produced by Filtertechnik Gera (fleece band 430mm) - control panel - manual switch i.D. * Rcedpfxsu Idxfo Aa Esk

Condition: new, Year of construction: 2025, Robland products are built by Werkhuizen Landuyt, located at Bruges, Belgium. Rsdpfx Aed Hz Nisa Esck BM 3000: • Saw aggregate for slot making. Max depth 10 mm • Left 5 mm bit for drilling • 20mm bit for minifix-system • 8 mm spindle for drill and limited milling applications • 35 mm bit for hinges • The thickness of the panels to be processed should be between 12 and 40 mm • The machine is equipped with a drilling head with 4 chucks and an integrated sawblade • Y axis reach/stroke: Drilling: 900 mm Grooving: 860 mm Technical data: • Y axis reach/stroke • Drilling: 920 mm • Grooving with sawblade: 860 mm • axis is supported 3000 mm • Z axis plate thickness from 12 mm up to 40 mm • A axis 360° • Movement speed: 20m/min • Min. dimensions workpiece (X) 300x (Y) x 120 x (Z) 12 mm • the machine is equipped with a bore head with 4 chucks and integrated sawblade. • Max/min diameter bore heads 3 mm – 35 mm • Saw blade operates in the X-axis • Max. Depth saw blade grooving: 10 mm • Motor 1 HP 3*380 V / 3*220 V • Minimal required dust extractor capacity 2300 m³/h

Condition: used, Year of construction: 1978, material width 500 mm coil weight 6,5 t material thickness 0,5 - 1,5 mm coil internal diameter 420 - 560 mm coil external diameter 1500 mm no. of straightening rolls 17 straightening roll diameter 50 mm number of draw-in rolls 4 Redpfxovuunas Aa Eeck speed 6 - 60 m/min dimensions of the straightener (WxDxH) 2,3 x 1,3 x 1,7 m dimensions of the decoiler (WxDxH) 1,3 x 1,2 x 2,0 m straightener (type R 500) with infinitely variable drive, adjustment of the roller box manual centralized double decoiler (type LH 2-1,5-500) with hydraulic centralized expansion, hydro-mechanical lag break as is where is, WITHOUT putting into operation, WITHOUT hydraulic aggregate

Condition: new, functionality: fully functional, power: 3.5 kW (4.76 HP), fuel type: diesel, color: yellow, overall weight: 160 kg, Year of construction: 2025, Equipment: UVV, Wacker Neuson Vibratory Plate Compactor DPU 2540 H, - NEW - Weight: 160 kg, Frequency: 90 Hz, Centrifugal force: 25 kN, 400 mm working width, Hatz diesel engine 1B20 with 3.5 kW, Other sizes available! Machine location: Warehouse D-46514 Schermbeck. Highlights & Advantages: Reversible vibratory plate (forward & reverse travel) Perfect for paving, pathways, curbstones, foundations, gravel & soil Very low fuel consumption & long service life Low-vibration guide handle for ergonomic operation Compact design → Ideal for confined sites & small areas Applications: ✔️ Landscaping & horticulture Rcjdpfx Aaoxyqmlj Esk ✔️ Fiber optic installation ✔️ Paving & terrace construction ✔️ Civil engineering & pipeline construction ✔️ Compaction of sand, gravel, chippings, aggregate ✔️ Construction sites of all kinds _____ Buy Wacker Neuson DPU 2540 | 25 kN vibratory plate | Diesel compactor | reversible plate compactor | new Wacker compactor | 400 mm plate | DPU 2540 H price | 160 kg compaction equipment | Hatz 1B20 compactor | Professional Wacker plate compactor | Buy soil compactor

Condition: new, Technical data: Working width mm 1.350 Min./max. working height mm 4 - 170 grinding belt width/ length mm 1.370/ 2620 Main motor power kW 15,0 with inverter Feed speed variable m/min 3,5 - 18 Working aggregates: 1st unit: "RA" inclined ribbed steel contact roller diameter 160 mm 2nd aggregate: Combi: rubber coated grinding roller diameter 160 mm, 45 Sh Elastic electronic link sanding shoe "MESAR" with 24 segments Version C: - Elastic electronic sanding shoe "MESAR" complete with: - Pneumatic cylinder (On/Off) for the automatic on/off of the sanding roller sanding shoe unit - Activation of the sectors by the electronic control which synchronizes their insertion with the feed speed and controls the number of sectors according to the workpiece geometry. and allows the selection of more or less sectors on the left and on the right side of the workpiece. Versions 135: "MESAR 24" with 24 segments, segment width 55 mm, complete with B/24 workpiece scanning bar in the infeed. Other equipment: Roller table in infeed and outfeed for long workpieces Perforated table and transport carpet Vacuum table with electric fan 4 kW (5,5 PS ) integrated in machine frame Oscillating blow-off device 2nd unit Touch screen 10,4" screen with 'eye S software integration Rcedpfx Aaehtuvre Eek ATTENTION: PICTURES are EXAMPLE PICTURES OF A SIMILAR SD70!

Condition: new, Equipped with a belt grinding tool it enables the clean, ready-to-cut finish of eight different, quickly adjustable radii by means of an oscillating sanding belt. The universal machine type RFM 320 S SET, equipped with an extra-­long machine table ensures time-saving complete machining of curved or chamfered edges in one operation. Base version RFM 320 S SET: › Adjustable grinding tool for 8 radii (2, 3, 4, 5, 6, 8, 10 and 12.5 mm) › Chamfering equipment up to 16 mm depth (continuously) › Grinding belt oscillation with pneumatic belt cleaning › Integrated base for feed unit › 16A socket for feed unit › Suction connections Ø 80 mm Rcsdpfx Ajf E Nqdea Eek inkl. premiling aggregate incl. wheels incl. pull- out table elongation Set-up dimensions approx. L x B x H in mm 1.300 x 690 x 1.010 Weight 145 kg

Condition: new, Rusticating machine for wooden artefacts such as boards, profiles, beams and strip wood for flooring, with maximum width 40 or 60 cm x 30 cm high. hight adjustment via hand wheel and numerical read out brush DM 200 mm machine in CE working width 600 mm max. working height 300 mm Rodpodd Hi Esfx Aa Eeck suction DM 2 x 140 mm motor feeder 0,37 kW feeder speed variabel 3 - 20 m/min motor brushing aggregate each 4,0 kW machine weight approx 750 kg inkl. 1 steel brush DM 200 mm 1 TYNEX brush DM 200 mm Advise used machines: • Technical data without obligation, mistake and intermediate sale reserve. • Price is considered ex-location price • All articles or machines are bought as seen without any entitlement on warranty. • It is left to the choice of the buyer to view the machines before at its location. • Special arrangements are possible but only valid in written form. (We answer your inquiries only with stated address + telephone number!)

Condition: excellent (used), Year of construction: 2002, edge seize 0,2 - 12 mm work piece dimension width min. 70 mm height min. / max. 8 / 42 mm length min 160 mm (strips) length min 60 mm from roll Durchlaufgeschwindigkeit: 12 m/ min glue coating with roller working height : 880 mm compressed air 6 bar,1/4 Zoll suction connection, DM 160 mm dimensions: L x W x H = 5600 x 950 x 1300 mm weight: ca. 2200 kg total conection: ca. 11,5 kW, 400 V, 50 Hz machine equipped with: - double top roll pressure with electric height adjustment - autom. roll magazine for rolls up to 800 mm DM, pneumatic cutting up to 3 mm - autom. infeed fence - no adjustment of edge seize premilling aggregate with 2 HF-motors 1,5 kW, 12000 n double end trim unit - 2 HF-motors 0,2 kW, 12.000 n 2 autom. positions = 0 + 3 deg. flush trimming aggregate with 2 HF-motors 0,7 kW, 12.000 n radius trimming unit - with2 HF-motors 0, 3 kW, 12.000 n, radius scraping unit, autom. set in flat scraping unit Advise used machines: Rjdpfx Aashy Tlro Eeck • Technical data without obligation, mistake and intermediate sale reserve. • Price is considered ex-location price • All articles or machines are bought as seen without any entitlement on warranty. • It is left to the choice of the buyer to view the machines before at its location. • Special arrangements are possible but only valid in written form. (We answer your inquiries only with stated address + telephone number!)

Condition: new, The model ME 40TR is SCM’s ‘bestseller and in this category offering unrivaled price / performance ratio. We can offer the following new machine SCM me 40tr, CE Volt 400 EU, frequency 50 Hz edge thickness coils 0,4 - 3 mm max. edge thickness strips 5 mm min. – max. work piece thickness 8 - 50 mm feed speed 9 m/ min glue pot unit 0,18 kW, capacity 0,8 kg premiling aggregate 2,2 kW, 9000 U/ min end-cutting unit with "Radius" allows you to make a radius on the corners of the edged panel trimming unit 2 x 0,35 kW, 12.000 U/ min OPTIONAL device for panel preheating Rcedpjc S Di Rjfx Aa Eok edge scraping unit flat scraping unit grooving unit 1,1 kW, 12.000 U/ min, notch width 4 mm brushing unit with 2 independent motors magazine for strip edges kid for quick exchange of glue unit ...

Condition: new, Year of construction: 2024, ALL ALTENDORF F25 TYPES READY ON STOCK! manual hight and Stilding adjustment for saw aggregate 0 – 46° Rcodog Dgr Hepfx Aa Esk digital display for saw blade height and tilting angle motor 5,5 kW saw blade speed 3600/ 4200 U/min. sliding table length 3200 mm angular fence for cutting length up to 3450 mm prearrangement for retrofitting of scoring unit saw blade DM max. 315 mm max. cutting height 104 mm max. cutting height at 45° = 70 mm working height 880 mm Advise used machines: • Technical data without obligation, mistake and intermediate sale reserve. • Price is considered ex-location price • All articles or machines are bought as seen without any entitlement on warranty. • It is left to the choice of the buyer to view the machines before at its location. • Special arrangements are possible but only valid in written form. (We answer your inquiries only with stated address + telephone number!)

Condition: good (used), Year of construction: 1988, Work piece thickness 0,4 - 8 mm Work piece height max. 51 mm Min. work piece width 50 mm min work piece length 180 mm Rodpfobahd Eox Aa Eock edge magazine for PVC and strips pneumatic pressure rollers for edge magazine edge snipping unit cutting unit with 2 saws milling aggregate buffing unit Feed speed 11 m/ min Glue application with fin nozzle Air pressure 6 bar length 3750 mm