Used roll benders (motor-driven) for sheet thickness over 14mm for sale (105)

Condition: ready for operation (used), functionality: fully functional, Year of construction: 1980, machine/vehicle number: 4350, roller (bottom) diameter: 280 mm, roller (top) diameter: 300 mm, sheet thickness (max.): 20 mm, overall weight: 14,200 kg, working length: 2,000 mm, TECHNICAL DETAILS Bending length: 2,000 mm Max. sheet thickness: 20 mm Bending capacity: 15/11 mm Bottom roller diameter: 280 mm Top roller diameter: 300 mm Pedpfx Aszi D Sasgxogp MACHINE DETAILS Drive power, main drive: 16.2 kW Drive power, top roller drive: 4.8 kW Drive power, bottom roller drive: 3.7 kW Weight: 14,200 kg

Condition: good (used), Year of construction: 2000, control type: NC control, controller manufacturer: Davi Smart, number of rollers: 4, roller (bottom) diameter: 340 mm, roller (top) diameter: 370 mm, side roll diameter: 320 mm, roller length: 3,100 mm, sheet thickness (max.): 25 mm, overall weight: 18,500 kg, total length: 5,900 mm, total width: 2,200 mm, total height: 2,300 mm, power: 30 kW (40.79 HP), Equipment: cone bending device, 4 roll plate bender Davi Promau - MCB-3037 MACH-ID 9751 Make: Davi Promau Type: MCB-3037 Control: Davi Smart Year: 2000 Conical bending attachment Extended roll end for section bending jobs Digital read out position side rolls Central lubrication CE-Declaration Rolling width: 3100mm Rolling thickness 3x toproll Ø:20mm Rolling thickness 5x toproll Ø:25mm Rolling thickness prebending: 22mm Top Roll Ø: 370mm Bottom Roll Ø: 340mm Side roll Ø: 320mm Number of rolls: 4 Rolling speed: 0-5 Adjustiment lower roll: 0-200mm/min. Adjustment side rolls: 0-200mm/min. Number of driven rolls: 2 Psdpozi Ra Rsfx Agxjgp Power: 30kW Length: 5900mm Width: 2200mm Height: 2300mm Weight: 18500kg Please Note: The information on this page has been obtained to the best of our ability and belief, and from the manufacturers where possible. It is given in good faith, but its accuracy can not be guaranteed. Accordingly, it will not form a representation or constitute contractual terms. We advise you to check any vital details!

Condition: like new (used), Year of construction: 2001, Technical data: Working width: 2050 mm Max. bending capacity for normal steel St40: 4.0 mm Pgedpeza D U Djfx Agxsp Max. edge bending for normal steel St40: 2.0 mm CNC control: MG Diameter of top roller: 140 mm Diameter of side bottom rollers: 105 mm Diameter of central bottom roller: 130 mm Conical bending device Working height: 800 mm Mobile control panel Hydraulic folding bearings CE marking Motor power: 3 kW Dimensions (length x width x height): approx. 3400 x 1200 x 1200 mm Weight: approx. 2.5 tons Condition: Very good condition, very little use The seller is not liable for typographical or data transmission errors. The machine's appearance, technology, and wear correspond to its age; used machines are sold without any warranty.

Condition: excellent (used), Technical Details: Working width: 3100 mm Maximum bending capacity: 16.0 mm Maximum pre-bending: 12.0 mm Top roll diameter: 300 mm Side roll diameter: 270 mm All three rolls powered Hardened rolls Pgedpfsxyvx Tex Agxep Conical bending device by tilting of both side rolls Swiveling control panel with digital display Hydraulic drop end bearing Motor power: 7.5 kW Dimensions (L x W x H): approx. 5800 x 1700 x 1500 mm Net weight: approx. 8.5 tons The seller is not liable for typing or data transmission errors. The machine's appearance, technical condition, and wear correspond to its age; used machines are sold without any warranty.

Condition: excellent (used), Year of construction: 2012, Technical Data: Pedpfx Agox Ii Hvjxsgp Working width: 2600 mm Bending capacity: 20.0 mm Pre-bending: 16.0 mm Top roll diameter: 330 mm Middle roll diameter: 300 mm Side rolls diameter: 240 mm Conical bending device via tilting of both side rolls Mobile control panel with digital display Motor power: 11 kW CE mark Dimensions (L x W x H): approx. 5800 x 2300 x 1900 mm Weight: approx. 11 t Additional equipment: Upper bending aid The seller is not liable for typographical or data transmission errors. The machine's appearance, technology, and wear are consistent with its age; used machines are sold without any warranty.

Condition: excellent (used), Year of construction: 2002, Technical specifications: Working width: 3550 mm Max. bending capacity: 42.0 mm Max. bending angle: 35.0 mm CNC control Diameter of top roller: 480 mm Diameter of 2nd top roller: 540 mm Pgjdpfx Agjittzfexop Diameter of side rollers: 480 mm Diameter of central bottom roller: 480 mm Conical bending unit through inclination of the two side rollers Mobile control panel with digital display Hydraulic pivoting bearings Weight: approx. 44 tons Optional equipment: Side bending aid Pivoting bending aid at the top Additional top roller The seller is not liable for typing or data transmission errors. The machine’s appearance, technology, and wear correspond to its age; used machines are sold without any warranty.

Condition: new, functionality: fully functional, The EVO is the latest innovation in sheet metal processing. It is equipped with numerous innovative and patented features that increase your production capacity and productivity, while offering the lowest total cost of ownership. The high-quality components used in this machine and the latest version of the BENDtronic® control system, which is installed as standard on all EVO machines, are particular highlights. Available from stock: HAEUSLER EVO 31031 4-roll round bending machine / roll bending machine Manufacturer: Haeusler Type: EVO 31031 4-roll round bending machine / roll bending machine Pedpfx Agexwmb Hsxsgp Origin: Germany / Switzerland Year of manufacture: 2024 Condition: NEW, exhibition machine Availability: immediately Performance: Working width 3100 mm Round bending capacity 14 mm Bending capacity 12 mm Not the right machine? As a representative of Haeusler, we can put together and offer you your desired machine according to your requirements. Please do not hesitate to contact us.

Condition: good (used), Year of construction: 2017, Sahinler 4R HSS 20-280 Hydraulic 4-roll plate bending machine – Year 2017. Bending length 2050 mm Max. bending capacity - mild steel 20. Upper roll diameter 280 mm Lower roll diameter 280 mm Lateral roll diameter 220 mm Pgodpfexau D Ijx Agxop Bending speed 1,5 / 5 m/min. Motor power 16 kW

Condition: used, functionality: fully functional, Year of construction: 1992, machine/vehicle number: 10842, We are offering this pre-owned sheet metal rolling machine Chr. Häusler VRM-hy 3000x15, year of manufacture 1992. Pjdpfxsx Sqc To Agxjgp Model: VRM-hy 3000×15 Serial number: WO 10842 Year of manufacture: 1992 If you have any questions or require further information, please do not hesitate to send us a message or call us.

Condition: good (used), Year of construction: 2008, sheet width 2050 mm plate thickness 20.0 mm ST pre-bending 16.0 mm ST diameter of upper rolls ca. 270 mm side roll diameter ca. 240 mm diameter of lower rolls ca. 250 mm Number of working hours ca. 7.800 h Control "EASY PRO" oil volume ca. 200 Liter voltage 380 V total power requirement 13.5 kW weight ca. 9.000 kg Dimensions (only the machine) 4000 x 2080 x 1800 mm Good condition (!!) Current list price approx. 150.000 euros Special price available upon request Features: - Robust electro-hydraulic 4-roll round bending machine * Arc-shaped feed of the side rollers (swing arm technology) - 4-roller design offers a wide range of bending and rounding options * Rolling process completed in a single pass - Mobile control unit * DAVI "DAVI EASY PRO" numerical control * Manual or automatic operation selectable * Programming "Self-Learning" mode available * Control of all rollers and machine axes * Digital position display for the rollers - Curved feed of the side rollers (DAVI "PSG" guide system) Podezc Rv Tepfx Agxsgp * Tight bending radii of up to 1.1 times the upper roller diameter possible * Instead of the usual 1.5 times with linear guides * Optimal bending = short sheet ends during bending - Conical rolling possible via roller tilt * Tight diameters possible due to low machine frame - Electronic roller parallelism - Stepless speed adjustment (max. 5.0 m/min) - Bending on both sides - Forged and hardened rollers with a hardness of 53-55 HRC - Low-maintenance, robust machine design - Easy sheet removal thanks to low machine frame - Sturdy welded steel construction - Electro-hydraulic swivel bearing for easy tube removal - Operating instructions

Condition: good (used), Year of construction: 1998, control type: NC control, number of rollers: 4, roller (bottom) diameter: 540 mm, roller (top) diameter: 560 mm, side roll diameter: 420 mm, roller diameter: 440 mm, roller length: 3,100 mm, overall weight: 45,000 kg, total length: 8,700 mm, total width: 2,900 mm, total height: 3,075 mm, power: 81 kW (110.13 HP), 4 roll plate bender HAEUSLER - VRM-hy MACH-ID 9638 Make: HAEUSLER Type: VRM-hy Year: 1998 Smallest bending diameter 640 mm Pressing force against upper roll 5800 kN Conical bending attachment Central lubrication Equipped for change rolls Rolling width: 3100mm Rolling thickness 3x toproll Ø:50mm Rolling thickness 5x toproll Ø:60mm Podpozbqquefx Agxsgp Rolling thickness prebending: 40mm Top Roll Ø: 560+440mm Bottom Roll Ø: 540mm Side roll Ø: 420mm Number of rolls: 4 Rolling speed: 0-6 Adjustiment lower roll: 0 - 200mm/min. Adjustment side rolls: 0 - 500mm/min. Number of driven rolls: 2 Power: 81kW Length: 8700mm Width: 2900mm Height: 3075mm Weight: 45000kg Please Note: The information on this page has been obtained to the best of our ability and belief, and from the manufacturers where possible. It is given in good faith, but its accuracy can not be guaranteed. Accordingly, it will not form a representation or constitute contractual terms. We advise you to check any vital details!

Condition: good (used), Scharringhausen round bending machine Type: UDR-X1-3 Capacity: 3000 x 30 mm Tube length: 3100 mm Upper tube diameter: 470 mm Lower tube diameter: 410 mm Engine power: 70 HP Pjdpeimmb Iefx Agxogp Dimensions: 830x245x295 cm LxWxH Weight: ca 55000 KG Included documentation Movie available!

Condition: good (used), functionality: fully functional, Year of construction: 1998, Type of machine: hydraulic 4-roll plate bending machine Manufacturer: MG Model / capacity: MG 2005 × 30 Year of manufacture: 1998 Number of rolls: 4 Working length of rolls: 2,005 mm Max. sheet thickness: 30 mm Pre-bending: yes, thanks to the 4-roll design Drive: hydraulic Control: separate control panel Application: bending of sheets, production of casings, tubes, cones and welded structures Condition: excellent Inspection possible: by arrangement Rolls: 4 pcs + 1 spare Pgodpfsznyilox Agxep 2 pcs working rolls, 300 mm 2 pcs auxiliary rolls, 200 mm Total length: 4500 mm

Year of construction: 1973, condition: like new (used), Used BRONX Heavy Duty Initial Pinch Pyramid bending rolls. Year of manufacture : 1973. MACHINE FORMERLY INSTALLED AT ROLLS ROYCE PLC IN DERBY UK. IMMEDIATELY FOR SALE AND NOW LOCATED IN BELGUIM WHERE IT CAN BE INSPECTED. SPECIFICATION CAPACITY Two sets of dimensions which are shown below as "Prebending & Rolling" and then "Rolling only". Material Mild Steel Mild Steel Tensile strength 28/32 tons/sq.in 28/32 tons/sq.in Maximum width 11’(3350mm) 11’(3350mm) Maximum thickness at this width 2” (50mm) 2½” (63.5mm) Minimum inside diameter of rolled cylinder at maximum capacity 30’ (762mm) 37 ½’ (953mm) Maximum thickness of plate when hot rolling (finished rolling temperature 850° C.) 4” (102mm) 5” (127mm) Minimum inside diameter of rolled cylinder at maximum capacity hot rolling 40” (1016mm) 50” (1270mm) MAIN PARTICULARS Diameter of all rolls - 27” (686mm) Body length of rolls - 11’2”(3403mm) Rolling speed - 12 f.p.m. (3600mm/min) Main drive motor - 150 H.P. Slip Ring Type Two bottom roll adjusting motors, each - 50 H.P. Slip Ring Type Combined operation of swing down bearing and top roll counterbalance - Hydraulically applied Hydraulic power pack motor - 10 H.P. Electrical equipment to be suitable for operation on a supply of - 400/440 volts, 3 phase, 50 cycles CONE ROLLING ATTACHMENT: To facilitate the rolling of taper or conical forms, a skid plate is fitted to the inside of the non-drive end housing. ELECTRICAL EQUIPMENT Motors: Main Drive - 150 H.P. half hour rated – slip ring screen protected – foot mounted type. Bottom Roll Adjustments - 50 H.P. half hour rated – slip ring screen protected – foot mounted type. Pgsdeh U Rzgspfx Agxsp Hydraulic Power Pack Motor - 10 H.P. continuously rated – Squirrel cage – screen protected – foot mounted type. Control Gear: Main Drive - Drum type reversing control gear with 5 minute rated wire wound resistances, designed to pass 100% full load on the first notch or operating position in each direction. The controller will be fitted with off position interlock and limit switch rings where necessary. Bottom Roll Adjustments - Drum type reversing control gear with 5 minute rated wire wound resistances designed to pass 100% full load on the first notch or operating position in each direction. The controllers will be fitted with off position interlock and limit switch rings where necessary. Hydraulic Power Pack - Direct-on-line contactor type starter, operated from a maintaining type push button station. Solenoid valves for operating cylinders are push button operated. Note: Full protection to be provided for all the above control gear by a circuit breaker, incorporating overload and no-volt protection. FEATURES AND EQUIPMENT Spare Roll included with the machine. LENGTH TBA MM WIDTH TBA MM HEIGHT TBA MM WEIGHT 95 tonnes NOTE: The information contained herein is provided in good faith, but however due to unforeseen errors or omissions cannot be binding as to accuracy.

Condition: new, sheet thickness: 45upper roll diameter: 460prebending: 35sheet length: 2600Bottom Roll Diameter: 420Side Roll: 360messurements (LxWxH): 5770 x 2300 x 2585weight approx.: 28500motor: 30 Technical specifications: - Hardened and polished rolls - Complete body made of ST-52 Steel - Machine have 4 rolls and designed for symmetrical working principle - Hydraulic powered cover for easy material extracting Pgodpsd Ab Rhefx Agxsp - Digital readout for side rolls (2 digital readout) - Side rolls are free for rotation and upwards downwards movements are hydraulic powered - Top and bottom rolls are driven by hydraulic and gearbox. Bottom roll’s vertical movements are hydraulic powered - Separate control panel form machine - Conic bending device - In accordance for CE norms Options: - variable speed of rotation EURO 5.858,-- - metarial feeding table EURO 5.100,-- - oil coiler STD. - center support EURO 18.750,-- - side supports EURO 12.500,-- - Automatic material extractor - PLC control - CNC control - Automatic material loading system - Changeable top roll - Adjustable bottom roll support system (for customer’s special requests) We have many references!

Condition: good (used), Year of construction: 2000, machine/vehicle number: 21977-1964, Offer 26165 Technical Data Podozf Hkdjpfx Agxjgp - Two driven rollers, each hydraulically adjustable - For edging and conical rolling - Operation via a separate control panel, with digital actual value display - and manual operation - Max. working width 1300 mm - Max. sheet thickness at 400 N/mm² without edging - at bending diameter 370 mm, inside 30 mm - with edging at bending diameter 370 mm, inside 25 mm - without edging at bending diameter 380 mm, inside and - width of 370 mm 45 mm - Upper roller diameter each 300 mm - Side roller diameter each 310 mm - Working speed 4.5 m/min - Drive 400 V / 30 kW - Space requirement W 5800 x H 1900 x D 2200 mm - Weight 8500 kg

Year of construction: 1978, condition: good (used), Make: HAEUSLER Type: VRM-HY Year: 1978 Specifications Metric US Standard Rolling width 3050 mm Rolling thickness 3x toproll Ø 60 mm Rolling thickness 5x toproll Ø 70 mm Rolling thickness prebending 50 mm Top Roll Ø 630 mm Bottom Roll Ø 600 mm Side roll Ø 500 mm Number of rolls 4 Rolling speed 0 - 5 Adjustiment lower roll 200 mm/min. Adjustment side rolls 200 mm/min. Number of driven rolls 2 Power 120 kW Dimensions (Estimate) Length 5790 mm Width 4200 mm Height 4200 mm Weight 85000 kg Please Note: The information on this page has been obtained to the best of our ability and belief, and from the manufacturers where possible. It is given in good faith, but its accuracy can not be guaranteed. Accordingly, it will not form a representation or constitute contractual terms. We advise you to check any vital details! Pjdpfekvm S Nsx Agxogp

Year of construction: 1980, condition: good (used), Make: HAEUSLER Type: VRM-HY Year: 1980 Specifications Metric US Standard Rolling width 3000 mm Rolling thickness 3x toproll Ø 130 mm Rolling thickness 5x toproll Ø 140 mm Rolling thickness prebending 120 mm Top Roll Ø Psdpfx Aekvm Szsgxegp 950 mm Bottom Roll Ø 850 mm Side roll Ø 180 mm Number of rolls 4 Rolling speed 2 + 4 Adjustiment lower roll 0 - 400 mm/min. Adjustment side rolls 0 - 400 mm/min. Number of driven rolls 2 Power 132 + 37 kW Dimensions (Estimate) Length 12000 mm Width 5440 mm Height 5650 mm Weight 286000 kg Please Note: The information on this page has been obtained to the best of our ability and belief, and from the manufacturers where possible. It is given in good faith, but its accuracy can not be guaranteed. Accordingly, it will not form a representation or constitute contractual terms. We advise you to check any vital details!

Year of construction: 2018, condition: good (used), Make: FACCIN Type: 4HEL 3590 Control: Siemens TOUCH Year: 2018 Specifications Metric US Standard Rolling width 3500 mm Rolling thickness 3x toproll Ø 80 mm Rolling thickness 5x toproll Ø 110 mm Rolling thickness prebending 90 mm Top Roll Ø 900 mm Top Roll Ø 900 mm Bottom Roll Ø 800 mm Side roll Ø 600 mm Number of rolls 4 Rolling speed 0-6 Adjustiment lower roll 0-200 mm/min. Adjustment side rolls 0-400 mm/min. Top support yes Side supports yes Number of driven rolls 2 Power Pgjdpokvm Nfsfx Agxjp 90+75+9 kW Dimensions (Estimate) Length 4430 mm Width 8800 mm Height 11000 mm Weight 178000 kg Please Note: The information on this page has been obtained to the best of our ability and belief, and from the manufacturers where possible. It is given in good faith, but its accuracy can not be guaranteed. Accordingly, it will not form a representation or constitute contractual terms. We advise you to check any vital details!

Year of construction: 2007, condition: good (used), Make: HAEUSLER Type: Clamp Year: 2007 Specifications Metric US Standard Min. shell inner diameter 1800 Max. shell inner diameter 5500 Min. shell outside diameter 1500 Max. shell outside diameter 2500 Minimum wall thickness 10 mm Maximium wall thickness 40 mm Max. section weight 15 T Max. weight total workpiece 60 T Dimensions (Estimate) Length Psdpfxskwcn Eo Agxsgp 24000 mm Width 6000 mm Height 3200 mm Weight 0 kg Please Note: The information on this page has been obtained to the best of our ability and belief, and from the manufacturers where possible. It is given in good faith, but its accuracy can not be guaranteed. Accordingly, it will not form a representation or constitute contractual terms. We advise you to check any vital details!

Year of construction: 1991, condition: good (used), Make: HAEUSLER Type: VRM-HY Year: 1991 Specifications Metric US Standard Rolling width 3000 mm Rolling thickness 3x toproll Ø 120 mm Rolling thickness 5x toproll Ø 150 mm Rolling thickness prebending 100 mm Top Roll Ø 910 + 820 + 740 mm Bottom Roll Ø 940 mm Side roll Ø 780 mm Number of rolls 4 Rolling speed 2 + 4 Adjustiment lower roll 200 mm/min. Adjustment side rolls 500 mm/min. Number of driven rolls 2 Power 300 kW Dimensions (Estimate) Length 8000 mm Width 5400 mm Height 5400 mm Weight 290000 kg Please Note: The information on this page has been obtained to the best of our ability and belief, and from the manufacturers where possible. It is given in good faith, but its accuracy can not be guaranteed. Accordingly, it will not form a representation or constitute contractual terms. We advise you to check any vital details! Pedpfokwcc Nsx Agxogp Share on

Condition: ready for operation (used), functionality: fully functional, Year of construction: 1992, machine/vehicle number: 11/10575, working width: 3,000 mm, sheet thickness (max.): 16 mm, TECHNICAL DETAILS Sheet metal width: 3,000 mm Sheet metal thickness: 16 mm Control system: conventional MACHINE DETAILS Pjdozapqwjpfx Agxjgp Rated current: 63 A Voltage: 380 V

Condition: ready for operation (used), functionality: fully functional, Plate rolling machine, 3000 mm capacity, H. Vuillot 3000 mm, used machine Manufacturer: H. Vuillot Sheet capacity: 3000 x 27 mm Top roll diameter: Ø445 mm Bottom roll diameter: Ø330 mm Psdpfx Agjwcqpnoxsgp Year: 1972

Condition: good (used), functionality: fully functional, control type: manual, degree of automation: manual, actuation type: hydraulic, number of rollers: 3, roller (top) diameter: 350 mm, side roll diameter: 325 mm, roller diameter: 350 mm, roller length: 3,050 mm, working width: 3,000 mm, working height: 1,500 mm, sheet thickness (max.): 25 mm, sheet thickness steel (max.): 25 mm, sheet thickness stainless steel (max.): 20 mm, overall weight: 13,000 kg, total length: 5,400 mm, total width: 1,950 mm, total height: 2,350 mm, power: 25 kW (33.99 HP), input voltage: 380 V, input frequency: 50 Hz, number of digital displays: 2, Equipment: cone bending device, documentation/manual, emergency stop, hardened rollers, swiveling upper roller, PLATE BENDING ROLL PINCH PYRAMID ON LINEAR GUIDEWAYS Bending capacity -Plate width 2500 mm -Rolling plate thickness 25 mm -Prebend thickness 20 mm -Rolls useful length 2550 mm -top roll D 350 mm -side rolls D 325 mm Hardened high strength surface of the 3 rolls Roll rotation driven hydraulic motor with gear unit Conical bending hydraulic tilt angle set of siderolls Pedpfx Aszdk Tyjgxogp Re-rolling system welded shells rounding. Opening hydraulic front drop-end top roll tiltup Electric motors 25 Hp on hydraulic unit Vac 380/50 Digital position readouts of the bending rolls Manuals with the machine Dimension mm5400x1950 x H 2350 mm -weight 13 ton

Condition: refurbished (used), functionality: fully functional, Year of construction: 2007, DAVI_MCB 3060 WT 4-roll plate bending machine CNC _ 3000x65 MM - Year of make 2007 Capacity plate width 3100 mm Plate thickness 65 mm Prebend 55 mm TOP ROLL 600 MM LOWER ROLL 550 MM Configuration installed: • Surface hardening of the four rolls • Dual pre-pinch, with adjustable force upon the input of plate thickness • Conical bending hydraulic attachment - hardened contrast pad. • Power driven rolls rotation top/bottom gearbox axial direct drive hydraulic each roll. • Calibration system for re-rolling of welded shells rounding. • Console electric independent with centralized commands joysticks and CNC screen readout. • CNC controller DAVI GENIUS semiautomatic and fully automatic programmable. with digital readout of the 4rollers for use in manual operation, • Opening front side hydraulic drop-end to unload closed shells. • Variable working speed step-less axis interpolation. • Safety installation with emergency stop. • Instruction manuals for operation and service Voltage electric 3phase Vac 380/50 power Kw 75 nr.1 top support hydraulic operated , shell ID max 5 mtrs - CNC programmable nr.1 side support hydraulic on the left nr.1 side support hydraulic on the right, finger pusher to swing the sheet plate forming cones rolling. Pgedpfx Agjy D Npisxop