Hydraulic four-roll bending machine

MG 2050 x 4 / 2 mm CNC

Condition: good (used), Year of construction: 1991, machine/vehicle number: 9108, Offer 26001 Technical Data: - Horizontal and vertical working positions - 3 motor-driven rollers - Hydraulic adjustment of the lower left roller - Pressing force of hydraulic cylinder: 4 t - Shaft diameter: 35 mm - Shaft rotation: 11 rpm Dkodpfx Asy Dqn Teqvsn - Roller diameter: 132 - 142 mm - Drive: 400 V, 1.1 kW - Bending capacity approx.: - Round tube Ø 800, 60 x 1.5 mm - Flat steel Ø 400, 90 x 15 mm - Square bar Ø 400, 30 mm - Includes: - Separate control panel with digital display - Foot switch on separate control panel for right / left operation - Standard bending set for flat and angle material - 6 sets of tube rollers: 22 + 28 + 33 + 42 + 48 + 60 mm - Weight approx.: 450 kg - Space requirement approx.: W 700 x H 1150 x D 950 mm

Condition: excellent (used), Year of construction: 2014, Flanging and dishing machine LUCAS - RD-3800 R MACH-ID 9280 Make: LUCAS Type: RD-3800 R Control: Siemens Simatic Year: 2014 Maximum diameter 3800 mm Minimum diameter 710 mm Thickness 40N/mm2 up to 6 mm Thickness 30 N/mm2 up to 8 mm Dodpfx Aqoxta E Rovskn Thickness 70N/mm2 up to 5 mm Flanging height 90 mm Working speed flanging 0 - 20 M/Min Working cutting speed 0-30 M/Min Tooling package included Please Note: The information on this page has been obtained to the best of our ability and belief, and from the manufacturers where possible. It is given in good faith, but its accuracy can not be guaranteed. Accordingly, it will not form a representation or constitute contractual terms. We advise you to check any vital details!

Condition: used, Year of construction: 2002, sheet width 3050 mm plate thickness 3.0 mm ST pre-bending capacity 3.0 mm ST upper roll diameter 170 mm lower roll diameter 170 mm side roll diameter 180 mm Control konv. 0 380 V total power requirement 3.0 KW weight 4250 kg In good condition With new rubber-coated top roll (!!) Also suitable for bending non-ferrous metals Dodsxacfgopfx Aqvekn - in checked conditions - machinevideo - ?v=ZW8Us6Hbm3E Equipment: - Electro-hydraulic 3-roll bending machine - Asymmetrical roll arrangement - Electro-motor-driven side roll adjustment * Including digital position display - Manual bottom roll adjustment * Via hand crank - Including conical bending device * Inclined bottom roll and side rolls * Parallel alignment in any side roll position - Hardened rolls SAE 1050 CK 45 - Manual folding storage for removing closed pipes * Top roll must be raised before opening the storage (e.g., forklift/crane) - Safety device - Connection cable + connector - 4-way foot switch * 2 buttons for side roll movement (up/down) * 2 buttons for roll movement (left/right) * With 4x new foot switch covers - Operating instructions (English) * Special accessories included: - Brand new top roller with plastic/rubber coating * Suitable for bending non-ferrous metals * Such as copper and aluminum

Condition: good (used), functionality: fully functional, Year of construction: 2002, control type: manual, degree of automation: manual, actuation type: hydraulic, pipe diameter (max.): 6,090,115 mm, tube wall thickness (max.): 3 mm, number of axes: 3, working height: 700 mm, input voltage: 380 V, input frequency: 50 Hz, type of input current: three-phase, operating pressure: 200 bar, pressure (max.): 200 bar, number of digital displays: 3, Equipment: CE marking, documentation/manual, emergency stop, quick-change device, Limpet coil roller hydraulic Dkedpfx Aeyik Hcjqvsn to form half round pipe from flat stainless steel strip and bending into wanted radius with spiral continuous. -Shafts output 80 mm -Interchangeable set of rollers on the shafts for the different size of pipe 60 mm , 90 mm , 115 mm -Coil holder for the reel metal strip with guide-way bench uncoiling and alignment the steel strip to the rolling machine -Pinching lower central roll adjustable to form the half pipe -Digital position readout to determine the bending diameter of the coil, the pitch of the coil, the half tube shape forming -hydraulic arm movable in 3 directions to set the pitch of the coil roll -Upper vertical support hydraulic operated to hold in position the formed diameter and collect the coils from diameter 700 to diameter 3000 mm -Operator console electric with push buttons and digital position readouts for the coil length, the bending radius and the forming load. -Service manuals and operation books along with the machine

Year of construction: 2017, condition: ready for operation (used), An asymmetrical three-roll plate bending machine MG is available. Working width: 2000mm, roller diameter: 130mm, max. plate thickness: 3mm, power: 6kW, weight: approx. 2000kg. An on-site inspection is possible. Dkodpfx Aoyttwboqven

Condition: new, functionality: limited functionality, Year of construction: 2025, control type: manual, Equipment: CE marking, documentation/manual, OMEC 4-Roller Mechanical Symmetric Plate Rolling Machine with Double Pinch 1530×2.5 mm Brand new, CE certified. Made in Italy. Double pinch. Top and bottom rollers powered with equal torque. Side rollers motorized for upward/downward movement. Front-opening top roller. Special bearings for side rollers. External lever to control roller inclination. Sheet clamping with bearing-actuated device. Two-pedal foot control. Electrical panel compliant with CE standards. Millimeter indicator for sheet clamping position. Standard equipment included with the plate rolling machine: - Frontal conical device on top roller. - No. 2 digital displays for the side roller positions. - No. 1 digital display for the motorized sheet clamping. - Grinding/Turning of rollers after hardening treatment. - Roller hardening. - Side sheet loading table with sheet centering stops, marked in mm. Working length: 1530 mm. Top and bottom roller diameter: 90 mm. Dsdpfxoy E Sche Aqvokn Side roller diameter: 95 mm. Plate thickness: 1.5 – 2 – 2.5 mm. (1.5 x D / 3 x D / 5 x D). Roller hardness: 55/60 HRC, 2 mm case depth. Installed power: 1.8 kW. Dimensions: 2290 x 750 x h 1150 mm. Weight: 690 kg.

Condition: excellent (used), Year of construction: 2014, sheet width 2050 mm plate thickness 6.0 mm ST pre-bending 5.0 mm ST diameter of upper rolls 170 mm side roll diameter 165 mm diameter of lower rolls 135 mm Control SIEMENS oil volume 80.0 Liter voltage 380 V total power requirement 7,5 kW weight 3450 kg Dimensions (only the machine) 3750 x 1170 x 1000 mm very good condition (!!) current new price incl. accessories approx. 70.000 Euro special price on request The FACCIN 4HEL model series is regarded in the industry as one of the most most precise, reliable and productive electronic 4-roll round bending 4-roll round bending machines worldwide. It has been specially designed Dkodjy Uy R Sspfx Aqvon for high throughput rates and maximum accuracy for medium to heavy sheet thicknesses. Features: - robust electro-hydraulic 4-roll round bending machine * with linear guidance of the rolls * the side rollers move on a straight, diagonal axis . up and down * extremely short distances between the rollers, . which increases the bending quality - 4-roll concept offers a wide range of bending and rounding options - Freely movable control unit * SIEMENS numerical control with touchscreen * Control of all rollers and machine axes * Digital position display of the side rollers * Manual operation possible via electric buttons - Infinitely variable adjustment of the bending speed - top roller and bottom roller with hydraulic motors and planetary gears * active rotary movement = side rollers run freely with - Conical rolling possible by tilting the rollers * Reduction of the maximum material thickness by approx. 50-60 % . during conical bending - Electronic roller parallelism (EPS) - Bending on both sides - diameters of up to 1.1 times the top roll diameter are possible - Forged and hardened rollers with a hardness of 53-55 HRC - Low-maintenance, stable machine concept - Sturdy welded steel construction - electro-hydraulic hinged bearing for easy pipe removal - pressure gauge / pressure display for the rollers - safety device (safety line with switch unit) - Manual central lubrication - operating instructions incl. circuit diagram CE explanation

Condition: like new (used), functionality: fully functional, Year of construction: 2019, Sahindler - Scantool profile bending machine Model PV 60 NC Year 2019 - New / Demo Roll diameter : 215 mm. Capacity flat iron : 120 x 25 mm. Capacity flat iron on edge : 80 x 20 mm. Capacity angle iron: 70 x 7 mm. Dksdpfxoytb U Us Aqvsn NC control 1 set profile bending rolls Hydraulic top roll movement Bending support Footpedal

Condition: excellent (used), functionality: fully functional, Year of construction: 2018, TIMAC TZZ-1604 Circular Disc Cutter with Double-Station Automatic Stacker. Year 2018 Inspected and ready for production. Automatic circular cutter for disc production from coil or strip, equipped with a double-station automatic stacker, enabling continuous operation without downtime. Specially designed for manufacturing ends and lids, circular blanks, and parts for deep drawing or stamping processes. Main features: • Circular cutting using adjustable blades • Diameter adjustment system for various disc formats • Double-station automatic stacker: - Vacuum arm for individual disc collection - Possibility to remove complete stacks without stopping production - Doors with safety latches and interlocks Dkjdpfx Asy Edk Roqvon • Integrated electrical and pneumatic system: - Independent electrical panel - PLC control - Safety compliant with CE regulations Key technical specifications: • Sheet thickness: - Up to 3 mm (carbon steel / aluminium) - Up to 1.5 mm (stainless steel) • Blade diameter: 100 mm • Installed power: approx. 16 kW • Electrical supply: 400 V / 50 Hz • Pneumatic pressure: 6 bar • Year of manufacture: 2018

Condition: ready for operation (used), functionality: fully functional, Year of construction: 1987, machine/vehicle number: 6197, Auction of a Thalmann THAKO folding machine! Dsdpfx Aqjyzhc Aevekn EQUIPMENT Depth stop Automatic program with stored sheet metal shapes