Used other waste management & recycling machinery for sale (89)

Condition: ready for operation (used), Specifications of NEUE Herbold SB 60/145 S7-3 Motor Power: 70kw Feed Opening: (approximately 620 mm x 565 mm) Rotor Configuration: 5-knife open rotor staggered Bed Knives: 2 Installed Screen: 3/16" (approximately 4.76 mm) Additional Equipment: Control panel with soft-start feature Voltage: 460V / 3-phase / 60 Hz Nsdpfx Ajw R Un Aedbowc Extras: Includes seven extra screens We supply a wide range of granulators designed for plastics recycling, manufacturing, and waste reduction. Whether you need compact units for light-duty use or heavy-duty machines for high-output production, we have the right solution.

Condition: reconditioned (used), Technical data feed hopper with hydraulic moving floor and bag opener for recyclables from yellow bags and residual waste: Manufacturer BRT HARTNER GmbH Type HP5-3035 Year of construction 2015 Hopper volume 30 m³ Drive line 17.5 kW Dimensions in current state 13,200 x 3,050 x 4,350 mm (l x w x h) Condition of the machine: The feed hopper with bag opener was used at a large recycling plant, where recyclable materials from yellow bags or commercial waste were tipped into the hopper using wheel loaders, the bags were opened using the bag opener, and the recyclable materials were transported to a sorting plant or the commercial waste was transported in measured quantities for further processing. The system functioned flawlessly until it was dismantled and replaced with a larger system with higher throughput capacity. The machine was dismantled into individual parts in our workshop, partially overhauled, reassembled, and tested during operation. The following overhaul work was carried out and the following spare parts were replaced: Dismantling of the feed hopper and bag opener into individual parts. Cleaning, partial sandblasting, priming and painting of the steel parts. Various wear and cover plates were newly manufactured and installed. Cutting off the worn ends (approx. 40cm) of the push floor pipes. Welding on the new pipes and smoothing the push floor pipes. Replacement of all plastic sliding plates for the hydraulic push floor. Removal of the hydraulic unit from the push floor, emptying of the hydraulic oil tank, replacement of the oil filters, refilling with new hydraulic oil. Replacement of the three hydraulic blocks, all valves, the oil sight glass and all hydraulic hoses from the hydraulic unit. The seal kit and hydraulic hoses were replaced on all three hydraulic cylinders of the push floor. All six limit switches (proximity sensors) on the push floor were replaced. The conveyor chains on the left and right of the scraper conveyor were replaced. Seven carrier bars on the scraper conveyor were replaced. The drive motor for the ripper blades was replaced. All nine pneumatic cylinders for the pressure pipes were replaced. All pneumatic lines and connections were replaced. All of the plastic sliding plates for the hydraulic operation of the bag opener were replaced. The bag opener can be moved vertically so that the system can also be used for commercial waste or residual waste without the bag opener. The side impact protection plates on both sides were replaced. Various wear parts of the bag opener have been replaced. The entire system has been rewired and reconnected. The system control in the control cabinet has been retrofitted by the manufacturer BRT Hartner to a self-sufficient individual control system and the standard programme has been reloaded into the control system. The system has been commissioned and tested by the manufacturer BRT Hartner, see the function video. Comments: The documentation (Manual, CE-declaration, electr./hydr.-drawings), are available. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors. Nodpfx Aeyizxrsdbowc

Condition: ready for operation (used), Lot Conveyor Belt Fasteners : 85  Boxes – Nilos SO11 37  Boxes – Nilos 7/vc 92  Boxes – Comet P15 21  Boxes – Mato U37/1200 56  Boxes – Asgor 4 Nsdpow Dxryofx Adbewc

Condition: ready for operation (used), Ventilator Nwsdpfsnac Ilex Adbjc Driving: 22 kW

Condition: ready for operation (used), a pallet Couplings (unused) Brand: Krupp Nwsdpfxei A Au De Adbec Diameter from 200mm till 800mm Tot. Weight appr. 25-35 tons

Condition: ready for operation (used), Rollers unused, year of manufacture 2015 Nsdpfx Adoi A Awmjbowc *510 pieces with Lenght: 380 mm — Diameter: 133 mm — Axis: 30 mm. *Brand: Precimeca / Continental:= SOLD OUT 857 pieces with Lenght: 750 mm — Diameter:  133 mm — Axis: 30 mm.= SOLD OUT 341 pieces with Lenght: 530 mm — Diameter: 133 mm — Axis: 30 mm.= SOLD OUT

Year of construction: 2025, condition: new, This robust professional cable stripping machine, type KM1, cuts electrical cables from 1 to 70 mm in diameter. The blades are hardened so when stripping reinforced ground cable they are not immediately blunted. Nedpfx Adop I I U Dsbjwc There are 15 different cable entries. The cable is cut from 2 sides so the copper core comes out easily. You can also use it to strip rubber and flat cables. Technical data: Mains voltage: 230 v ~ 50 hz Power: 3000 watts with dual pulley drive. Dimensions: 60 cm long, x 75 cm wide and 90 cm high Machine speed: 35 m/min Output: Depending on the cable 400 and 1200 kg/day Weight: 185 kg.

Condition: used, New: Yes Applicable material: Oil Nwjdpfxsykcfvo Adbjc

Condition: ready for operation (used), Ventilator Radial Brand: Radial Nwsdpfxsv Swqfe Adbjc Driving: 19 kW

Year of construction: 2013, condition: used, We offer you a used PET bottle crusher of the manufacturer BOREMA, type R-1200 F, year of construction 2013, for residual emptying, deaeration and pre-compaction of the fed PET bottles, from 0.3 up to 2.5 l content. The machine has a chassis and can be moved into and out of the feed chute of your baler. The machine has a throughput capacity of approx. 85,000 bottles/h, corresponding to approx. 3t/h. Nwedpfxju Thpnj Adbjc We have the following technical information: Manufacturer: BOREMA Umwelttecjhnik AG Type: R-1200 F (with trolley for retracting and extending) Year of manufacture: 2013 Drive power: 11 kW Connected load: 15 kW Rated current: 32 A Back-up fuse: 40 A Type of construction: Continuous system Function: Double rotor press system Rotor pretension pneumatic: approx. 16t Overload protection: by anti-blocking system Input material: PET disposable and returnable empty bottles 0.3 to 2.5 L capacity Input material: HDPE bottles and canisters up to 3 l capacity Throughput capacity: approx. 3 t/hour, corresponding to approx. 85,000 bottles/hour, depending on size Required compressed air output: G1/2", 8 bar, 40 l/min. Compression ratio: 1:3 Flange dimensions inside: 972 x 1220 mm Feed opening: 565 x 1280mm Weight: approx. 2500kg Possible applications: Due to the chassis, the PET flattener can be moved into the feed chute of your baler as required, thus ensuring residual emptying, venting and pre-compaction of the fed bottles and canisters. When the material is changed, the PET flattener is simply moved out of the feed chute again and paper, cardboard, film, etc. can now be pressed further without using the flattener. Process of the BOREMA PET crusher: The plastic packages are drawn in by two rotating shafts. One of the rotating shafts is pneumatically pretensioned by two air bellows and presses the PET bottles with 16 t of pressure against the second rotating shaft. In the process, the closed plastic bottle is squeezed together, caused to burst and vented. Residual liquids run out and the material falls into the baler in a precompressed state. When impurities are introduced, the pneumatically pre-tensioned shaft deflects to the side and the impurities are channeled through. Significant advantages compared to conventional PET perforators with punching mandrels or knives: The BOREMA process is much more efficient and less subject to wear than conventional PET perforators with punching mandrels or knives. The biggest advantage is that any foreign matter such as metal parts, stones, bottles with frozen contents and pieces of wood are passed through the pneumatically deflecting rotor shaft without stopping the operation of the system or causing any major damage. With conventional perforators, mandrels or blades sometimes break off or become so jammed with the interfering material that the plant has to be shut down and repaired at great expense. Comments: The crusher is in good condition, was dismantled from the running operation, stored, is available at short notice and after assembly immediately ready for use. The documentation (manual, CE, electrical/hydraulic circuit diagram) is complete. An inspection is possible by arrangement. The technical information is taken from sales brochures, the operating instructions or other information provided by the manufacturer. We accept no liability for incomplete or incorrect data and informations.

Year of construction: 2013, condition: used, Technical data of the bale opener line for RDF. MSW, paper, cardboard: Manufacturer Cross Wrap Oy Ltd, Siilinjärvi, Finland Type BO 4000 Year of manufacture 2015 Quantity of opened bales 674 pieces Operating time only 3 days, exclusively by running in the entire line during new installation Opening time approx. 45 seconds per bale Bale dimensions (W x H x L) 1100 x 1100 x 1400 - 1900 mm Max. Bale weight 2,000 kg Conveying height of the system 1,400 mm Max. Conveying width of the system 1,200 mm Material to be opened RDF/MSW Availability of the line 98% Noise level of the bale opener line 85 dB(A) Total connected load 37 kW Rated current 125 A Operating display SIEMENS SIMATIC HMI Touch Control SIEMENS S7 ET200S Installation dimensions 8,463 x 2,890 x 3,960 mm (l x w x h) Scope of delivery: Feed conveyor 3,500 x 1,200 x 1,400 mm Feed conveyor to opener 1,500 x 1,200 x 1,400 mm Bale opener (gripper with knife) Special equipment: Oil heating in hydraulic oil tank Heating in control cabinet Oil cooler in Hydraulic unit Explanation of the short period of use: The entire line of Cross Wrap bale openers type BO 4000 was installed at a municipal waste incineration plant in 2015. The background to the installation was that in the case of a malfunction or maintenance of the incinerator, the municipal waste could continue to be received, baled, wrapped and stored until the malfunction was cleared. Then the bales should all be opened again and the waste fed into the normal incineration process. This worst-case scenario never came to pass. The plant was set up, run in and then never used in regular operation. Only during the commissioning and running-in of the entire plant in 2015 were 674 bales opened on three days. The plant is in very good condition and ready for operation immediately. Due to reconstruction measures in the incineration plant, the installation area of the bale opener was needed. As a result, the entire line is for sale. Short description of the wrapping process: The pressed bales are placed on the infeed conveyor belt from the side or from behind by means of a forklift truck. For opening, the bales must run horizontally to the conveyor belt with the wire or twine binding, otherwise the bales must be turned 90° beforehand. The opening conveyor brings one bale at a time in front of the cutting unit. The grippers hold the wires or twine strapping. The front and rear rotating knives slit the bale lengthwise. Afterwards, the gripper returns to the starting position. The opened bale is now conveyed via the conveyor belt to the discharge chute and then falls onto the following conveyor system. Nwjdpfx Adju Tg I Debsc Comments: New price of the completely plant 296.000,- €. The documentation (operating instructions, CE declaration, electrical/hydraulic circuit diagram) is complete. The unit has been dismantled into freight-manageable units, stored and is available for inspection and loading at short notice. We do not accept any liability for the technical details or any errors.

Year of construction: 2021, condition: ready for operation (used), A single-shaft shredder Erdwich for contaminant-free red brass and brass chips is available. Cutting unit dimensions X/Y: 600mm/500mm, height: 300mm, knife width: 25mm, screen hole diameter range: 25mm-35mm, machine dimensions X/Y/Z: approx. 1600mm/650mm/800mm, weight: approx. 600kg. Documentation available. An on-site inspection is possible. Nodpoymfc Nefx Adbjwc

Condition: used, machine/vehicle number: 10521, Length of magnetic grinding table = 1300 mm Drive = 13.5 kW Magnetic table can be swiveled Nwodsyhr A Eopfx Adbsc Ideal for re-sharpening rotor and stator blades Water cleaning with filter cloth

Condition: ready for operation (used), Optical separator scheider Titech Tomra Nedpfox Str Rjx Adbowc Brand: Titech Tomra Type: Autosort NIR1 S2000 X-L Incl.: belt conveyor length 5000 mm, Beltwidth 2000 mm.

Condition: ready for operation (used), Optical separator Titech Tomra Brand: Titech Tomra Type: Autosort NIR1 S2000 X-L Nodsx Sttbjpfx Adbjwc

Condition: excellent (used), functionality: fully functional, 1. Permanent Magnetic Separator – SK25 (250 mm) Nedpfx Aox Ekpasdbowc Ferrous metal removal unit used inline in the ducting system to protect machinery and ensure clean, contaminant-free material. Key Features: • 250mm diameter • High-strength magnetic core • Inline installation • Removes staples, clips, and metal fragments • Improves bedding quality Price: £900

Condition: excellent (used), functionality: fully functional, Large-format inline magnetic separator for capturing ferrous contaminants before material enters the balers. Nedsx Ekn Aopfx Adbjwc Key Features: • 300mm diameter • Industrial-grade magnetic assembly • Reduces equipment damage • Improves purity of finished product Price: £1,400

Condition: good (used), Year of construction: 2018, functionality: fully functional, Loading system for automatic filling of 2 walking floor vehicles with loose waste/recyclables, consisting of a steel structure with maintenance platform, 2 traversing conveyors and one reversible conveyor, as well as optionally a chain belt conveyor for feeding from below. Conveying capacity approx. 200 m³/h. Nwedoylzm Uopfx Adbjc

Year of construction: 2026, condition: new, functionality: fully functional, This robust professional cable stripping machine, model KM1-F, processes electrical cables with diameters ranging from 1 to 70 mm. This model features speed control via a frequency inverter. - The blades are hardened, ensuring they do not dull quickly when stripping armored cables. - The machine has 15 different cable feed entries. - The rollers feature grooves on their beveled surfaces for improved grip on the cables. - The cable is cut from both sides, allowing the copper core to be easily removed. - It is also suitable for stripping rubber and flat cables. - The machine meets all safety requirements. - A comprehensive service manual and user instructions are included. Nedpeyfw Egjfx Adbewc - Maintenance procedures are also detailed in the documentation. Technical specifications: - Power supply: 230 V ~ 50 Hz - Power: 2200 watts with geared drive - Dimensions: 60 cm long x 75 cm wide x 90 cm high - Machine speed: adjustable - Output: Depending on the cable type, between 400 and 1200 kg/day - Weight: 185 kg - Price includes VAT Spare parts such as blades, drives, bearings, etc., are also available. If desired, we can also perform maintenance on these machines. A machine that is ready for immediate use and easy to operate. If you would like to test it, please bring your own cable.

Condition: good (used), Year of construction: 2012, functionality: fully functional, Rotary Airlock Valve / Rotary Valve Nestro, year of manufacture 2012, for the separation / differentiation of paper chips or paper edge strips Technical data: Manufacturer: Nestro Lufttechnik GmbH Year of manufacture: approx. 2012 Njdpfx Aox Uz I Sjdbowc Motor: 4 kW Max. volumetric flow: 28,000 m³/h Max. inlet diameter: 450 mm Speed: 22 rpm Rotor width: 1,500 mm Rotor diameter: 1,200 mm Dimensions: 2,200 x 2,200 x 2,500 mm (LxWxH) Weight: approx. 3,000 kg Remarks: The machine is in good condition. It has been inspected and tested at our facility in 28816 Stuhr. You can find the video above on our website or on our YouTube channel. Inspections, including under power, are possible at any time by prior arrangement. We are happy to answer your questions about the machine by phone, Monday to Thursday from 08:00 to 14:00. On Fridays, we are available from 08:00 to 13:00. Please note: All technical data is based on information provided by the manufacturer. We do not accept liability for the stated information or possible errors. Offers are non-binding, subject to prior sale, and may be withdrawn at any time. Inspections are possible by arrangement. Sale is ex-works, advance payment required, without warranty or guarantee.

Year of construction: 2022, condition: ready for operation (used), System includes a Vecoplan shredder, a scraper chain conveyor, and a lifting-tilting device with safety guard, the system was used for recycling plastic, 1) Vecoplan shredder VIZ 1300 S, with hood-type feed hopper, base frame, discharge electrode, scraper chain conveyor, lifting-tilting device, feed length: 1250mm, feed width: 1300mm, type: electric motor with V-belt drive, rated motor power: 90kW, rated motor current: 169A, motor speed: 750/min, protection class: IP55, rotor diameter: 495mm, number of cutting crowns: 87 pcs., dimensions of cutting crowns: 40x40mm, rated rotor speed: 185/min, rotor speed range: 95-265/min, screen hole diameter: 40mm, drive side: right (standard), overall length: approx. 2850mm, overall width: 2515mm, overall height: approx. 1350mm, weight: approx. 7200kg, 2) Scraper chain conveyor, trough width: 500mm, section length: 2700mm, screw diameter: 315mm, screw length: 3000mm, conveying speed: 24m/min, drive power: 2.2kW, 3) Lifting-tilting device, with safety guard and safety light curtain, lifting capacity: approx. 500kg, tilting angle: 150°, discharge height: approx. 3390mm, container length/depth: 857mm, container width at discharge edge: 1060mm, container height: 916.5mm, container clearance height: approx. 255mm, container weight: approx. 135kg, max. container weight with product: 500kg, container volume: 0.5m³, lifting and discharge speed: 6.6m/min, motor power/rated current: 1.5kW/4.95A, transport chain: 2 pcs., safety chains/chain break protection: yes, chain breaking force per strand: 70,000N, operating hours reading: approx. 6400h. With complete documentation, additional spare parts are optionally available. An on-site inspection is possible. Nwsdpfx Adsx Dm A Rjbec

Year of construction: 1994, condition: ready for operation (used), Motor power: 15.5kW/19.5kW, pressing force: 320kN, spec. pressure: 425kN/m², machine dimensions X/Y/Z: approx. 5700mm/1900mm/1800mm, weight: approx. 6000kg. The machine has a defect due to moisture and should be checked. Nwsdeip D Rpopfx Adboc

Year of construction: 1988, condition: ready for operation (used), A regeneration plant Erema is available. Components: conveyor belt, extrusion unit, screen changer, strand pelletizer, control unit, and intermediate conveying system. An on-site inspection is possible. Nwodpfxow Dfgwe Adboc

Year of construction: 2008, condition: ready for operation (used), A Strautmann plastic briquetting press is available. Pressing force: 300kN, hopper type: TS 1600, system dimensions X/Y/Z: approx. 6750mm/1900mm/2750mm. Documentation available. An on-site inspection is possible. Nwsdpfxex El Ahe Adbsc

Year of construction: 2008, condition: ready for operation (used), A large-format single-shaft shredder Vecoplan is available. Rotor diameter: 370mm, effective rotor length: 1300mm, speed: 120rpm, knife rows: 37, knife dimensions X/Y: 40mm/40mm, feed opening X/Y: 1400mm/1300mm, hopper volume: approx. 3m³. Machine dimensions X/Y/Z: 3200mm/2400mm/1500mm, weight: approx. 5500kg. An on-site inspection is possible. Nsdpeyddyzsfx Adbowc