Drum chipper

ZENO ZTH 1600 / 1400 E 550

Condition: good (used), WD creel type GXW 71, with spherical roller bearing in the main shaft. Suitable for all base plates of GXV and GXW creels. Fully hydraulic. With hydraulic saw tensioner. Kdedpsuql Iljfx Ampek Ideal as a replacement sash gang or swing replacement.

Year of construction: 2023, condition: ready for operation (used), Two Vecoplan scraper chain conveyors are available. 1) VKU 800, year of construction: 2023, drive power: 5.5kW, belt speed: 24m/min, conveying capacity: approx. 120m³/h, belt width: 820mm, max. incline: 70°, section length: 10.2m. 2) VKU 1100, year of construction: 2023, drive power: 11kW, belt speed: 24m/min, conveying capacity: 180m³/h, belt width: 1150mm, max. incline: 70°, section length: 22mm. Documentation available. On-site inspection is possible. Ksdpst Iw Rysfx Ampsdk

Condition: new, Year of construction: 2026, SPIRAL DUCT PRODUCTION MACHINE Metformer MTF 1602 TUBEFORMER Designed for the production of round SPIRO-type ducts. The produced duct complies with DIN EN 12237, BS, and Eurovent standards. Features: Coil decoiler with vertically adjustable brake Forming strips for duct production Burr-free high-speed cutting with circular cutting blades LCD touchscreen control Automatic lubrication system Automatic cutting during duct production Production reporting system (daily-weekly-monthly output) Automatic error detection Technical Data: Kdsdewa Skhjpfx Ampek Diameter range: 80–1600 mm Thickness range: Galvanized steel: 0.4–1.2 mm Stainless steel: 0.4–0.7 mm Aluminum: 0.4–1.3 mm Strip width: For 0.4–1.0 mm thickness: 137 mm For 1.1–1.3 mm thickness: 140 mm Production speed: 60 m/min Motor power: 11.25 kW Beading: Smooth, single or double Lock: External lock Cutting system: Circular cutting system Weight: 2900 kg Machine dimensions: 1900 × 2050 × 1500 mm Decoiler dimensions: 1780 × 1130 × 1250 mm Table dimensions: up to 2700 × 950 × 1200 mm Operating Environment: Power supply: 3-phase, 380V, 50Hz Clean surroundings Maximum ambient temperature: 40°C Minimum ambient temperature: -5°C Humidity: 55–85% Altitude:

Year of construction: 2026, condition: new, -Drum diameter 1600mm -Drum length 2880-3880-4880mm -Working length 2000-3000-4000mm -Grid holes according to your specifications -The screen consists of a closed profile -A cleaning brush with a diameter of 300 mm is mounted on the screen and along the entire length of the working part -Flat bar blades installed in the center of the drum allow the material to be poured -Drum rotation speed approx. 11.5 rpm Kedpfxjq T Sp Hj Ampedk - Sieve feed sieve via gearmotor- Drum transmission via gearmotor + 2 rubber drive wheels diameter 230 mm - Sieve equipped with electrical panel - Gravity feed hopper, dimensions Width 1600 mm, Length 1400 mm, Height 1200 mm - 12 months warranty - Made in Europe - CE compliant

Year of construction: 2001, operating hours: 123 h, condition: ready for operation (used), machine/vehicle number: 123, Metal silo for storage of woodchips, etc. Technical description: silo DM: 5m Height: 8 m with outfeeding unit (screw conveyor connection to output) Cappacity: 42 m3 Kdodoftdv Uopfx Ampjk With outfeeding transport screw conveyor to the top of the silo building. Already dismountled, visit possible by appointment at our warehouse H-2013 Pomáz/Hungary.

Year of construction: 1986, condition: good (used), Technical Details : Products - - Flats - 10x3 - 25x3 mm 10x4 - 25x4 mm 12x5 - 20x5 mm - Square - 6x6 - 12x12 mm Kjdsd H Ur Ajpfx Ampodk - (T) Profile - 20x10x3 mm - ( L) Profile - 15x15x3 - 18x18x3 mm Raw Material wire - 8,9,10,11,12,13,14,16 mm Transformer Power - 20 Kw Speed - 35m/min

Condition: new, Year of construction: 2023, Application combs 10 mm Application combs 15 mm Kdsdpfsiacbpjx Ampsk Application combs 20 mm finger joint profile 15 mm finger joint profile 20 mm delivery time 3 days

Condition: used, SPE Renergi Low Temperature Dryer. The Renergi Dryer is used for drying of sawdust and other materials for production of biofuels. The dryer can dry sawdust, bark or wood chips from a humidity level of about 50% to a level of approximately 10 %. This low-temperature dryer utilizes warm (or hot) water from a recommended temperature of 65°C and higher. Maximum water temperature - 110°C. Kjdpowp Rqfefx Ampodk Power supply safety: The dryer must only be fed by 3x400 V AC (630 A) 50/60 Hz with a separate Protective Ground conductur. Power supply Data: • Voltage 400 V AC, three phase • Recommended fuses in supply line: maximum 3x630 A • Typical power consumption: 200kW The dimension of the Dryer are roughly 17,4 by 5,7 meters, with a height of 10,7 meters. The floor space required is approximately 21,4 by 8,0 meters. A ceiling height of at least 15 meters (or 4 meters above the top of the media inlet). Air supply: at least 24 kg gas/s fresh air is required for the operation of this machine. This corresponds to 20nm3/s, or 72 000 nm3/h. Airflow: max 200 liter/min Air pressure: min 4,5 bar, recommended 6,0-8,0 bar Water supply: hot water supply, with a flow of 32 dm3/s. Water pressure: min 1.5 bar, max 6.0 bar Operating temperature range: • Incoming air temperature: -20°C to 50°C • Relative humidity: 0% to 60% Raw material/media: • Relative humidity: 45% to 55% by wieght • Requested relative humidity: 8% to 15% in the dried material Capacity: • The dual-cell, 4 m wide dryer can typically handle 2400 kg of material with a moisture content of 55% by weight in each load • The dryer is capable of drying 6000 kg raw material, with a water content of 55% to 10% in approximately one hour. SRE’s dryer is desinged in accordance with European directives. The equipment is designed to conform to the essential requirements of: • The Machinery Directive 2006/42/EC • LVD 2006/95/EC • EMC 2004/108/EC The dryer is located in Straupe parish, Cēsis district, LV-4152, Latvia. Available for viewing on working days, 08:00 to 17:00, by prior agreement on the viewing time. The dryer is already dismantled All electrical schematics, manual, operating instructions available Upon request, we can provide a contact person with this type of working dryer for consultation Price:20,000.00 EUR (VAT is not included)

Condition: new, Year of construction: 2025, Cardboard Core winder maschine for Toilet Tissue paper rolls Specifications • Carton web width 60 - 76 mm • Production speed 35 - 40 m / min Kdodpoit N Rvsfx Ampsk • Core i. diameter 40 mm - 80mm • No. of plies 2 , 3, 4 plies. (more optional) • Cut off length 600-2900 mm Features • Operation with either hot or cold glue. • Exchangeable mandrels. (for different core size) • Crush cutting by two or three circular cutters with synchronized movement. • Variable speed – electronic. (three phase)

Condition: ready for operation (used), Year of construction: 2015, operating hours: 9,612 h, spindle speed (max.): 18,000 rpm, overall weight: 11,600 kg, table width: 650 mm, table length: 800 mm, travel distance X-axis: 750 mm, travel distance Y-axis: 650 mm, travel distance Z-axis: 560 mm, controller manufacturer: HEIDENHAIN, controller model: 640, number of axes: 5, This 5-axis DMG MORI DMU 75 Monoblock was manufactured in 2015. It features an impressive X-axis travel of 750 mm, Y-axis travel of 650 mm, and Z-axis travel of 560 mm. The machine is equipped with a maximum spindle speed of 18,000 rpm and offers 60 tool positions. If you are looking to get high-quality machining capabilities, consider the DMG MORI DMU 75 Monoblock universal machining centre we have for sale. Contact us for further details. • Power: 48 kVA • Rated apparent power: 35 kVA • Max input current: 70 A • Full load current: 80 A • Voltage: 400 V • Frequency: 50 Hz • Control voltage: 24 V • Spindle speed: up to 18,000 1/min • Tool interface: HSK • Tool magazine capacity: 60 positions • B-axis: -5° to +110° • C-axis: 360° • Table size: 800 mm (L) x 650 mm (W) • Machine Protection Control (MPC) • Infinitely variable speed control • Operating mode 3 Additional equipment • Scraper belt chip conveyor (chip conveyor) • Internal coolant supply • 40 bar coolant system with 600 l tank and paper belt filter • 40 bar IHK pressure relief valve • Coolant ring nozzle • Water jet gun / cleaning gun • Air cooling system through spindle center • Mechanical oil and emulsion mist separator, 3 bar • Blum laser for tool radius and length measurement • Heidenhain TS 460 infrared touch probe • Handwheel Kdedpfx Ameyx D Dkspjk • Climate control package • Documentation/manual • Preparation for automation/handling system • Extractor probe • Optional: Schunk zero point system and tools