Used Wollmer Chp for sale (205)

Year of construction: 2014, operating hours: 59,436 h, condition: used, functionality: fully functional, machine/vehicle number: 100010336, Buderus Loganova EN20 CHP Unit, 19 kW electric / 38 kW thermal For sale is a Buderus Loganova EN20 combined heat and power (CHP) unit manufactured in 2014. The unit comes from a commercial property in 70567 Stuttgart and is being decommissioned due to an upgrade of the energy supply. Since commissioning, the CHP unit has been regularly serviced as part of a premium maintenance contract. A documented service history is available. °°°Technical Data:°°° Prsdpszv Sfnofx Aicoa * Manufacturer: Buderus * Type: Loganova EN20 * Serial Number: 100010336 * Year of Manufacture: 2014 * Electrical Power: 19 kW * Thermal Power: approx. 38 kW * Fuel: Natural Gas * Fuel Power: 35–56 kW * Electrical Operating Range: 9.5–19.0 kW * Supply Voltage: 400 V * Rated Current: 36 A * Rated Frequency: 50 Hz * Pre-fuse: min. 63 A * Gas Inlet Pressure: 20–65 mbar * Max. Supply Temperature: 85 °C * Max. Operating Pressure: < 6 bar * Device Type: B23 * Protection Class: IP40 * Rated Speed: 1,522 rpm °°°Operating Hours:°°° * 59,436 operating hours * 6,031 start cycles °°°Condition:°°° The unit starts and runs up properly. Currently, there is a fault in the heat exchanger. Based on initial assessment, the heating water pump is defective. The CHP unit is currently out of operation and is being offered with the corresponding repair requirements. °°°Location:°°° 70567 Stuttgart, Germany The planned decommissioning or dismantling is expected to take place between August and September 2026. An inspection is possible after prior arrangement. We will gladly provide additional photos, technical documents, and information on the available service and maintenance history upon request. Sale of a used technical unit in its current condition.

Condition: good (used), Year of construction: 2021, total width: 500 mm, total length: 800 mm, total height: 500 mm, overall weight: 65 kg, sheet thickness (max.): 40 mm, operating speed: 2,600 mm/s, Cutting machine CEVISA - CHP-12 MACH-ID 9406 Make: CEVISA Type: CHP-12 Year: 2021 Max. nominal thickness 40 mm Max. recommended thickness 20 mm Max. bevel length in several runs 18 mm Max. bevel length in single run 12 mm MIn. bevel inner diameter 100 mm   X Bevel K Bevel V Bevel Y Bevel High average cutters lifespan around 1000 M Self feed Zero maintenace Min. Beveling angle: 22.5° Max. beveling angle: 45° Min. plate thickness: 4mm Maximum sheet thickness:40mm Power: 3 HPkW Feed rate: 2600mm/min. Length: 800mm Width: 500mm Height: 500mm Weight: 65kg Please Note: The information on this page has been obtained to the best of our ability and belief, and from the manufacturers where possible. It is given in good faith, but its accuracy can not be guaranteed. Accordingly, it will not form a representation or constitute contractual terms. We advise you to check any vital details! Psdpfx Aijzcng Aecsra

Condition: good (used), Year of construction: 2013, total width: 500 mm, total length: 800 mm, total height: 500 mm, overall weight: 65 kg, sheet thickness (max.): 40 mm, input voltage: 3,000 V, operating speed: 2,600 mm/s, Cutting machine CEVISA - CHP 12 MACH-ID 9404 Make: CEVISA Type: CHP 12 Year: 2013 Max. nominal thickness 40 mm Max. recommended thickness 20 mm Max. bevel length in several runs 18 mm Max. bevel length in single run 12 mm MIn. bevel inner diameter 100 mm   X Bevel K Bevel V Bevel Pjdpfozcngcjx Aicera Y Bevel High average cutters lifespan around 1000 M Self feed Zero maintenace   Min. Beveling angle: 22.5° Max. beveling angle: 45° Min. plate thickness: 4mm Maximum sheet thickness:40mm Power: 3 HPkW Feed rate: 2600mm/min. Length: 800mm Width: 500mm Height: 500mm Weight: 65kg Please Note: The information on this page has been obtained to the best of our ability and belief, and from the manufacturers where possible. It is given in good faith, but its accuracy can not be guaranteed. Accordingly, it will not form a representation or constitute contractual terms. We advise you to check any vital details!

Condition: excellent (used), Year of construction: 2024, functionality: fully functional, machine/vehicle number: 6125, We sell a used CEVISA beveling machine CHP-60G INV, MFG 2024, SN: 6125 60 mm bevel length; capability in one run: 28 mm bevel length; bevel finish: machined (milling head); adjustable bevel speed depending on the material; optimum beveling speed: 500 mm/min; continual plate fixing pressure system: 4 Bar; 3 feeding rollers always in contact with the plate; 1 roller positioned in the cut-off point to insure: - no vibration; no noise; -smooth and unchanging finish; portable milling machine; mobile and stable; adjustable working height with pneumatic lifting system; electronic bevel adjustment; display: high precision; built-in adjustable bevel angles from 15º to 70º * Nominal thickness: from 10 mm to 100 mm. Motor: three-phase; motor power: 5 CV – 3.8 kW; voltage: 220/380 V. 50 Hz; 250/440 V. 60 Hz; 32 A plug, cable diameter: 2.5 millimeters, maximum consumption of the machine: max. 15A. Electric box with: thermomagnetic switch trip +emergency stop button, Psdpfxev Ef Ryo Aicsra net weight: 800 kg; works height: adjustable from 760 to 940 mm; built-in trolley; bevel blueprint; plate beveling: K, V, X, and Y bevels, bevel speed: 0,5 m/min, three-phase motor: three phases and earth. no neutral, motor power: 5 hp - 3.8 kW, air flow rate 200 l/min. Electrical box: with under-voltage trip, emergency stop button, magneto-thermal protection; net weight of the beveling machine: 800kg, working height: adjustable from 760 to 940 millimeters. Integrated carriage. Price: 37.000 Euro + VAT, negotiable, FCA Oradea/Romania Irrtum, Änderungen und Zwischenverkauf vorbehalten / Subject to errors, changes and prior sale / Ne rezervăm dreptul la greșeli, modificări și vânzare prealabila. We speak English. /Wir sprechen Deutsch./ Beszélünk magyarul. /Nous parlons français/Vorbim romana

Condition: excellent (used), Year of construction: 2024, functionality: fully functional, machine/vehicle number: 6119, We sell a used CEVISA beveling machine CHP-60G, MFG 2024, SN: 6119 60 mm bevel length; capability in one run: 28 mm bevel length; bevel finish: machined (milling head); adjustable bevel speed depending on the material; optimum beveling speed: 500 mm/min; continual plate fixing pressure system: 4 Bar; 3 feeding rollers always in contact with the plate; 1 roller positioned in the cut-off point to insure: - no vibration; no noise; -smooth and unchanging finish; portable milling machine; mobile and stable; adjustable working height with pneumatic lifting system; electronic bevel adjustment; display: high precision; built-in adjustable bevel angles from 15º to 70º * Nominal thickness: from 10 mm to 100 mm. Motor: three-phase; motor power: 5 CV – 3.8 kW; voltage: 220/380 V. 50 Hz; 250/440 V. 60 Hz; 32 A plug, cable diameter: 2.5 millimetres, maximum consumption of the machine: max. 15A. Electric box with: thermomagnetic switch trip +emergency stop button, net weight: 800 kg; works height: adjustable from 760 to 940 mm; built-in trolley; bevel blueprint; plate beveling: K, V, X, and Y bevels, bevel speed: 0,5 m/min, three-phase motor: three phases and earth. no neutral, motor power: 5 hp - 3.8 kW, air flow rate 200 l/min. Electrical box: with under-voltage trip, emergency stop button, magneto-thermal protection; net weight of the beveling machine: 800kg, working height: adjustable from 760 to 940 millimeters. Integrated carriage. Price: 34.000 Euro + VAT, negotiable, FCA Oradea/Romania Irrtum, Änderungen und Zwischenverkauf vorbehalten / Subject to errors, changes and prior sale / Pjdpfev Ed N Iox Aicera Ne rezervăm dreptul la greșeli, modificări și vânzare prealabila. We speak English. / Wir sprechen Deutsch. / Beszélünk magyarul. /Nous parlons français/Vorbim română

Year of construction: 2025, condition: new, functionality: fully functional, Unused, brand new CHP unit with a TOYOTA 4Y engine, all-in-one design, employing a “plug and play” concept for easier and cost-effective installation, a user-friendly interface, a safety module for enhanced hardware protection, and a single-bearing generator to minimize potential engine damage. Psdpfjzl H Atjx Aicera This 20 kWe CHP unit is ideally suited for locations with a continuous demand for both electricity and heat. The key to CHP’s economic viability lies in utilizing the heat generated in conjunction with electricity production. Product location: Indop, d.o.o., Primorska 6a, 3325 Šoštanj, Slovenia.

Condition: used, Year of construction: 2005, operating hours: 140,000 h, functionality: limited functionality, Name: Used CHP Unit Pedpfx Aijwyax Tjcera Manufacturer: Köhler / Ziegler Type: SY 53 GSM Year built: 2005 Generator: Leroy Somer Generator Type: LSA 44.27/4 Generator kW: 132 kVA Fuel type: Sewage gas Electrical power: 53 kW Thermal power: 87 kW Driving force: MAN E0836 E302, 6 Zylinder, 56 kW Dimensions: L 3600 x W 950 x H 1750 mm Empty weight: 2200 kg Technical doc.: Yes Message: The Engine was changad in 2013 Condition: Used Price: On demand

Condition: ready for operation (used), Year of construction: 2015, functionality: fully functional, overall weight: 4,000 kg, fuel type: gas, power: 80 kW (108.77 HP), continuous power: 80 kW (108.77 HP), total length: 3,500 mm, total width: 800 mm, total height: 2,000 mm, motor manufacturer: MAN, CHP plant / Combined heat and power plant with MAN gas engine – manufactured in 2016. For sale is a combined heat and power plant (CHP) with a MAN gas engine and an APROVIS heat exchanger. Technical data: * Heat exchanger manufacturer: APROVIS Energy Systems Pjdpfx Aoznn Aaeicjra * Year of manufacture: 2016 * Heat output of heat exchanger: 32 kW * Engine: MAN gas engine * Robust industrial design * Ideal for energy and heat generation The system is suitable as a source of spare parts, for refurbishment, or for continued industrial use. Condition: Sold as shown in the pictures. Inspection possible by appointment. Electricity: 50 kW. Heating: 80 kW.

Condition: like new (used), Year of construction: 2022, functionality: fully functional, fuel: liquefied natural gas (LNG), - 1x CHP unit - As new - Control cabinet still in original packaging - Located in Genthin We are selling a CHP unit in as-new condition. It has never been used, and the control cabinet is still in its original packaging. Pjdpfxozazrao Aicsra It has never been used but has been regularly maintained and is fully functional. The CHP unit is located in Genthin and can be inspected at any time.

Condition: excellent (used), Year of construction: 2014, functionality: fully functional, total length: 69,000 mm, total width: 16,000 mm, total height: 16,000 mm, The system was designed and dimensioned according to Eurocode EN 1993 for the industrial drying of wood chips, sawdust, or similar biomass products and is suitable for use in biomass, wood, or pellet production. Process components: Pjdszw Apgepfx Aicsra Air heater, deflection rollers, feeding modules, discharge modules, trough chain conveyor, belt tensioning and adjustment device, 7 exhaust stacks (height up to approx. 17.6 m) Designed for hot air or waste heat utilization (e.g., biomass boiler or CHP plant), with thermal enclosure made of sandwich panels. The system has been disassembled and stored by an experienced assembly team; this team can be arranged for transport and reassembly.

Condition: used, Year of construction: 2005, operating hours: 140,000 h, Name: CHP used Manufacturer: Köhler / Ziegler Type: SY 53 GSM Year built: 2005 Generator: Leroy Somer Psdjwyaxgjpfx Aicjra Generator Type: LSA44.2S7/4 Generator kW: 132 kVA Turbo: No Fuel type: Sewage gas Electrical power: 53 kW Thermal power: 87 kW Driving force: MAN E0836 E302, 6 Zylinder, 56kW Dimensions: L 3.600 x W 950 x H 1.750 mm Empty weight: 2.200 kg Technical doc.: Yes Message: The engine was changed in 2013 Condition: Second hand Price: On demand

Condition: used, Year of construction: 2008, Name: Used CHP Unit Manufacturer: SEnergie GmbH Type: G6.12TI Year built: 2008 Generator: NEWAGE STAMFORD Generator Type: UC.I274D2 Generator kW: 100 kW Fuel type: Sewage gas Pedjy Am Rnjpfx Aicjra Electrical power: 80 kW Thermal power: 123 kW Efficiency: 88,9 % Dimensions: L 3.500 x W 1.100 x H 2.500 mm Empty weight: 3.000 kg Technical doc.: Yes Message: In 2018 a new engine was installed and the generator was rewound. Last service on October 15. 2021 with 86.102 hours. Accessories: A switch cabinet Condition: Second hand Price: On demand

Condition: new, Year of construction: 2022, functionality: fully functional, machine/vehicle number: KOG 130, output voltage: 400 V, output frequency: 50 Hz, type of output current: three-phase, nominal power: 150 kW (203.94 HP), continuous power: 130 kW (176.75 HP), rotational speed (max.): 1,500 rpm, motor manufacturer: MAN, type of cooling: water, A cogeneration plant on wood biomass KOG130_00 with equipment was designed to convert solid fuel into gaseous fuel. In the process, the produced gas is cleaned and cooled, after which it is forwarded to the internal combustion engine of the cogeneration plant. Podpeywgp Hefx Aicera For solid fuel, natural wood chips of class G50-G100 are used. CHP line is equipped with containerized MAN UPB -L-W-E3262E302 Woodgas genset.

Condition: new, Year of construction: 2020, functionality: fully functional, machine/vehicle number: 81159538275956, power: 275 kW (373.90 HP), number of cylinders: 12, rotational speed (min.): 1,500 rpm, overall weight: 1,763 kg, Available MAN based woodgas modules. Available quantity - 23 units. Never used (new) Under separate agreement for potential buyers we offer service of rebuilding these engines to natural gas or diesel specs. MAN V12X-2200  12 cylinders. 29,6 litres displacement  Bore 138 mm, stoke 165 mm  Power 1618 kW MAN V12X-2000  12 cylinders. 24,2 litres displacement  Bore 128 mm, stoke 165 mm  Power 1471 kW MAN V12-1900  12 cylinders. 24,2 litres displacement  Bore 128 mm, stoke 165 mm  Power 1397 kW MAN V12-1650-1800  12 cylinders. 24,2 litres displacement  Bore 128 mm, stoke 165 mm  Power V12-1650-1213kW, V12-1800-1324kW MAN V12-1550-1400  12 cylinders. 24,2 litres di Pedpsxcudajfx Aicjra  Bore 128 mm, stoke 165 mm  Power V12/1550-140KW-1213KW, V12/1400-1029KW MAN diesel engines for commercial shipping MAN D3872 (LIGHT, MEDIUM-DUTY OPERATION)  12 cylinders. 29,6 litres displacement  Bore 138 mm, stroke 165 mm  Power 1471 - 1618 kW / 1213 Kw MAN D2862 DUAL FUEL (MEDIUM DUTY OPERTAION)  12 cylinders. 24,2 litres displacement  Bore 128 mm, stroke 157 mm  Power 794kW MAN D2862 (LIGHT, MEDIUM & HEAVY-DUTY OPERATION)  12 cylinders. 24,2 litres displacement  Bore 128 mm, stroke 157 mm  Power 1029-1471 kW / 749-1066kw / 551-735Kw MAN Auxiliary engines MAN D2862  12 cylinders. 24,24 litres displacement  Bore 128 mm, stroke 157 mm  Power 600-800kW

Condition: used, (14) Unused Man UPB 12-L-W-E3262E302 CHP cogeneration units with capacity 130kWel and 226 kWTh made in 2022 and designed to be fed by wood gas. Project was dropped so the equipment was never installed or commissioned. Pjdpfx Aoyhc T Isicora Plant includes the following major equipment: - Man 12 cylinder engine rated 273 kW, 50Hz, 1500 RPM - Marelli MBX-E 250 MA4 generator rated 169 kVA, 400V, 50Hz, 1500 RPM - AFR Air-Fuel Ratio control system by Motortech - Generator control system by ComAp (14) units available.

Condition: used, Year of construction: 2009, operating hours: 64,000 h, functionality: limited functionality, overall weight: 2,500 kg, fuel type: gas, motor manufacturer: MAN, Köhler & Ziegler MAN GAS Combined Heat and Power Plant (CHP) 54 kW - Leroy Somer Generator We are offering a Combined Heat and Power Plant (CHP) ⭐︎ Condition: The CHP unit is used but in good condition. ⭐︎ Condition: good (used) Fully operational and well maintained! Recently dismantled! The MAN E0834 E302 is a stationary natural gas aspirated engine primarily used in combined heat and power plants (CHP) for the simultaneous generation of electricity and heat. This four-stroke Otto gas engine features a compact design with four cylinders in-line. Manufacturer: Köhler & Ziegler, Germany Engine: - Manufacturer: MAN - Engine type: MAN E0834 E302 - Design: 4-cylinder in-line engine, water-cooled - 4.6 litre - 1500 rpm Generator Pedoy Rz N Uspfx Aicora - Manufacturer: Leroy Somer (Germany) - 90 kW - 3 phase 400 Volt - 50 Hertz - Operating hours: approx. 64,000 hours Dimensions: L:3100 mm x W: 1000 mm x H: 2000 mm Weight: approx. 2500 kg Condition: - Used – Good The generator was used in a publicly accessible building. Regular maintenance was carried out ⭐︎ Further technical data: see photos. Scope of delivery as shown Will be delivered as shown Inspection before purchase is possible and expressly encouraged. All our items are dismantled, cleaned, and visually checked for damages by our qualified personnel before sale. For all item-relevant data/information, please refer to the description and photos. All statements are made to the best of our knowledge and belief. The offered goods are sold as described and inspected. International buyers welcome Please inquire for shipping costs to Europe and overseas #2. Storage Shelf 44-1-8 Scope of delivery: - MAN GAS CHP unit 54 kW - With electrical control cabinet Shipping: - Nationwide transport within Germany is available for an additional charge - To provide an exact freight quote, please send me a request with your ZIP code

Condition: ready for operation (used), Year of construction: 2010, operating hours: 122,000 h, functionality: fully functional, power: 250 kW (339.91 HP), number of cylinders: 8, Used combined heat and power (CHP) unit, manufactured in 2010, for sale, complete with container. MAN gas engine overhauled in 2024 (proof of overhaul available in the form of an invoice). Prjdpfx Aezkwc Ioicsa

Condition: ready for operation (used), Year of construction: 1993, functionality: fully functional, fuel type: gas, output current: 178 A, output voltage: 6,600 V, output frequency: 50 Hz, continuous power (apparent): 1,976 kVA, motor manufacturer: MWM Deutz, MWM Deutz TBDG 441 BV16, including generator for combined heat and power (CHP) plant, dual fuel, gas, diesel, year 1993. Prsdpfx Aiey Hmhbecea Spare parts also available for sale: turbocharger, injection pump, cylinder heads, crankshaft, etc. 7 units of engines and generators available, AVK 6600V 173A 50Hz, control unit.

Condition: new, Year of construction: 2016, functionality: fully functional, type of input current: three-phase, input voltage: 400 V, We are offering two new Totem 20 combined heat and power units (CHP) as well as a new Totem 10 CHP unit, year of manufacture 2016. These CHP units come from the liquidation of storage inventory. According to the previous owner, the units are eligible for CHP funding, as they have never been installed. However, this must be verified independently. The TOTEM 20 delivers a maximum output of 20 kW electrical and 48.5 kW thermal. The TOTEM 10 delivers a maximum output of 10 kW electrical and 25.2 kW thermal. For all further technical details, please refer to the uploaded datasheet and user manual. Pedpfxsytympo Aicera Depending on location, delivery within Germany or Austria can be arranged. Price negotiable. The new list price for a Totem 20 is currently approximately €57,000 (gross) and they are traded for €45,000 (see photo). We are offering you an unbeatable deal. If you have any questions or need more information, please feel free to send us a message or call us. We offer a start-up guarantee, meaning we will take the units back in the event of difficulties at start-up, but we do not cover any incurred costs.

Condition: used, Year of construction: 2020, operating hours: 35,933 h, functionality: fully functional, machine/vehicle number: 200202-0010, total length: 8,250 mm, total width: 2,600 mm, total height: 3,150 mm, type of input current: DC, input voltage: 400 V, input frequency: 50 Hz, Equipment: documentation/manual, emergency stop, type plate available, We are offering our outdoor drying system, model RG 50, from Heber. This weather-resistant, container-like drying unit is used for the technical drying of: Wood chips Grain Hay / Straw Bulk goods in general Pjdpfx Aiozba Nyocjra The system operates according to the principle of convective warm air drying: Heat source Waste heat (e.g., from a CHP unit) Alternatively, oil/gas heating Air treatment, fan draws in ambient air, air is heated, drying process Warm air flows through the material, moisture is absorbed, exhaust air, moist air is discharged High energy efficiency through waste heat utilization, uniform drying, automated operation. Air flow rate: 55,000 m³/h Continuous operation (24/7 possible) Danfoss control system, manual is available. With 6 possible connections for drying containers. The system is still connected but is no longer in operation. Dismantling is the responsibility of the buyer! A telecrane and a low-bed trailer are required for transport! Inspection is possible by appointment!

Condition: used, Year of construction: 2016, functionality: fully functional, machine/vehicle number: F16/56XTA1/A/01, overall weight: 1,120 kg, load capacity: 100 kg, input voltage: 400 V, type of input current: three-phase, Stäubli TX200 industrial robot including CS8CHP controller and Stäubli teach pendant – manufactured in 2016. We are offering a used Stäubli TX200 industrial robot for sale, including the original Stäubli CS8CHP controller. Technical specifications: Manufacturer: Stäubli Model: TX200 Controller: CS8CHP Year of manufacture: 2016 Payload: 100 kg Condition: Used Scope of delivery: Stäubli TX200 robot Original Stäubli CS8CHP controller Stäubli teach pendant Connection cable Operating manuals Scope of delivery as shown in the photos The robot comes from an industrial research and development environment and has been carefully maintained. The system was in operation until it was dismantled. Inspection is possible by appointment. We will gladly send you further photos or technical information upon request. Prjdpfx Aiozli Huecja

Condition: not inspected (used), Year of construction: 2007, functionality: unexamined, total height: 2,600 mm, total length: 12,200 mm, total width: 2,500 mm, overall weight: 13,000 kg, Combined Heat and Power Plant (CHP), Manufacturer: STIEGELE, housed in soundproof special containers, 800 kVA Podsy Iu Hnspfx Aicsra Manufacturer: Stiegele Year of manufacture: 2007 Operating hours: approx. 12,000 per engine Engines: Make: 2 x Scania DC 12-54, Variant A03P Engine speed approx. 1,500 rpm each Electric drive: EMK type KS160L-4-PTC Feed pump: Elektra type DD0705 Mode of operation: Palm oil (primary), Diesel / Heating oil. The CHP was designed for operation with vegetable oil (palm oil) and has been converted accordingly. For continuous operation with heating oil or diesel, technical modifications may be required. Generators: Make: 2x Marelli Type: MJB315MA4 Output: 880 kVA Touch control: Manufacturer Woodward, Type GCP-30 Dimensions (per container): Length: approx. 12,200 mm Width: approx. 2,500 mm Height: approx. 2,600 mm Weight: approx. 13,000 kg The CHP system is modularly installed in two 40" soundproof containers and has been out of operation for some time. The sale includes the containers, control system, and heating oil tank. Viewing and inspection of the system is expressly encouraged. Sale exclusively to commercial customers. Any and all liability for material defects and warranties is excluded. The machine is sold used and as inspected, with no guarantee or assurance of specific properties. Claims for damages are only possible in cases of intent, gross negligence, or injury to life, body, or health.

Condition: new, Year of construction: 2026, power: 180 kW (244.73 HP), number of cylinders: 12, cubic capacity: 25 cm³, nominal power: 200 kW (271.92 HP), Thermal output 320 kW Predpfxey Urx Ue Aicea

Condition: like new (used), Year of construction: 2013, For sale is a Leadwell lathe LTC-25 iM -Control Siemens Sinumerik 828D -Operating hours approx. 1000h "rather less" -connected load approx. 23 KW weight approx. 6.7t Prjdpfsh Aw Rkox Aicea -Turning diameter max. 310mm turning length 1,000 rpm range 35-3,500 rpm -Bar passage D 77mm -VDI drum turret (VDI 40 with driven tools) -Speed ​​range 3000 rpm, number of tools 12 pieces -Tool measurement via Renishow probe manually stretchable -Programmable tailstock with M functions/ additional foot switch for quill movement -Coolant system 4 bar -Adjustable clamping pressure of the chuck -Hainbuch quick-change system, centroteX/ capteX on collet small/collet large/jaw chuck D250mm Various collets "see pictures" can also be purchased -Preparation for attachment of a bar feeder -Preparation for collecting device for workpieces -Set-up dimensions approx. 5000 mm x 2300 mm x 2000 mm -Hinged belt chip conveyor -Training documents and machine documents as well as other documents from attachments are available. -Machine is under power and is still in use -Delivery time Immediately -Many tool holders, turning tools, drills and tables can be purchased at an additional cost. see pictures

Condition: not inspected (used), Year of construction: 1998, functionality: unexamined, machine/vehicle number: 7814-0045, total length: 4,000 mm, total width: 1,500 mm, total height: 2,000 mm, Weight approximately 3000 kg For sale is a used machine from a site closure. Psdpfx Aezqam Asicera Sale is made excluding any warranty for defects. The machine has not been inspected but was operational until the very end.