Used Cogeneration Chp for sale (635)

Condition: used, Fröling wood gasifier HVG, wood power generation plant CHP, year of construction 2018, 40,000 operating hours, 115kW thermal output, 56kW electrical output, incl. fuel transport, incl. agitator discharge in the bunker, incl. ash removal with screws in big bags, incl. control system, incl. exhaust system with flare, incl. carburetor with (reformer, gas cooler, gas filter) incl. CHP engine, system must be dismantled by the customer, good fuel quality required, fuel moisture max. 13%, system is being handed over due to lack of time for maintenance and upkeep, available immediately. Ijdpfx Asvyrwpoacobc

Condition: used, Used 5.9 MW Wartsila Vasa 18V32DF dual fuel cogeneration plant built in 1998 with ABB HSG 900 LS8 generator. Plant includes: - Wartsila VASA 18V32DF engine. This is a turbo-charged, intercooled four stroke gas engine with direct pilot fuel injection with the following specifications: Vee configuration, 18 cylinders, 320mm cylinder bore, 350mm stroke, 750 rpm, 2 inlet valves/cylinder, 2 outlet valves/cylinder, clockwise rotation and nominal output of 5901 kWm. Iodpfxjw U A I Ej Aacjbc - ABB HSG 900 LS8 generator. This is a self-cooled, 3-phase, brushless, synchronous, two bearing type generator with the following specifications: 7235 kVA, 0.8 power factor, 11000 V, 380 A, 50 Hz, 750 RPM, 900 RPM, insulation class F, IP21 protection and IEC34 standard.

Condition: used, Year of construction: 2003, total length: 4,420 mm, total height: 2,700 mm, total width: 1,500 mm, Applicable material: Food Empty weight: 1.200 kg GVW: 1.200 kg Current frequency: 50 Hz Voltage: 380 Ibjdpsvlzx Tofx Aacsc

Condition: ready for operation (used), Year of construction: 2018, operating hours: 60,873 h, functionality: fully functional, input voltage: 400 V, type of input current: three-phase, input frequency: 50 Hz, power: 2,679 kW (3,642.42 HP), empty load weight: 10,000 kg, fuel: domestic gas H, control cabinet height: 2,000 mm, control cabinet length: 600 mm, control cabinet width: 800 mm, nominal power: 2,679 kW (3,642.42 HP), rotational speed (min.): 1,500 rpm, type of cooling: water, GE Jenbacher JMS 616 GS-N.L – Gas CHP Unit Fuel Type: Natural Gas Electrical Output: 2,433 kW Thermal Output: 2,420 kW Total Efficiency: 85.6% Electrical Efficiency: 42.9% Thermal Efficiency: 42.7% Voltage: 690 V Frequency: 50 Hz RPM: 1,500 Engine Configuration: V16 (60° angle) Bore x Stroke: 190 mm × 220 mm Displacement: 99.8 L Ibsdpfxewptfrj Aacec Fuel Consumption: Approx. 597 Nm³/h (at LHV 9.5 kWh/Nm³) Noise Level: 101 dB(A) at 1 metre Dry Engine Weight: approx. 10,000 kg Dimensions (L×W×H): 8,300 × 2,200 × 2,800 mm ⚙️ Included Equipment Turbocharged engine with intercooler STAMFORD LVSI 804 W alternator (rated 3,555 kVA) LEANOX control system Electronic ignition system Full lubrication system (pump + filters) Heat exchangers for coolant and oil Control panel with visual interface Pre-heating system Gas train according to DIN-DVGW standards

Condition: used, Year of construction: 2018, functionality: fully functional, Spanner RE2 biogas engines with full RHI and ROCS transferrable - 4 off at 45kw power and heat output each (total 180kW power) Iedpfxjv T Txuj Aacsbc - Split into 2 separate water systems. - 2 x 2000L buffer stores - 2 x heat exchangers (more available on request) - 30kW fan - 20m of 2m x 2m ducting - G99 compliant - Gas data system - Biogas RHI, Biomass RHI and ROCS for a further 13 years

Year of construction: 2011, operating hours: 105,992 h, condition: refurbished (used), functionality: fully functional, output frequency: 50 Hz, rotational speed (min.): 1,500 rpm, machine/vehicle number: 0280025/001, We offer a fully refurbished Stamford HC.I634H2-CG generator (500 kW / 860 kVA) designed for a biogas Iedpfxoxn Inis Aacebc CHP (BHKW) unit. The generator was professionally overhauled and tested in 2025. General overhaul performed by Generam s.r.o. (Czech Republic) – authorized STAMFORD | AvK Parts & Service Dealer. A full refurbishment report is available. Technical data: - Power: 500 kW (860 kVA) - Manufacturer: Stamford - Type: HC.I634H2-CG - Year: 2011 - Operating hours: not known - Voltage: 400 V / 50 Hz - Speed: 1500 rpm - Condition: completely overhauled (2025) - Application: biogas plant / CHP unit - Availability: immediately Documentation: Refurbishment report available. Inspection possible. Price: €22,000 net (negotiable) Location: 15320 Neuhardenberg, Germany

Condition: excellent (used), Carbide saw grinder VOLLMER model CHP eco Ibedeqahf Aepfx Aacoc

Year of construction: 1995, condition: good (used), machine/vehicle number: 4202, Technical data: Isdpfjd Af Shsx Aacobc -Plate thickness up to 6-40 mm -Pipe Beveling min. Ø 100 mm -Max bevel in one run 10 mm - speed 2.6 m / min -Drive 400 V / 2,2 kW -Space requirement approx. B T 550 x 500 x H 700 mm -Weight approx. 65 kg

Condition: new, functionality: fully functional, Year of construction: 2023, machine/vehicle number: 12502120, Cylinder heads are no longer used as the CHP unit has been decommissioned! Ibjdpjxc Dwisfx Aacec

Condition: used, Year of construction: 2005, operating hours: 140,000 h, functionality: limited functionality, Name: Used CHP Unit Manufacturer: Köhler / Ziegler Type: SY 53 GSM Year built: 2005 Generator: Leroy Somer Generator Type: LSA 44.27/4 Generator kW: 132 kVA Fuel type: Sewage gas Electrical power: 53 kW Thermal power: 87 kW Ibsdpowyax Tjfx Aacsc Driving force: MAN E0836 E302, 6 Zylinder, 56 kW Dimensions: L 3600 x W 950 x H 1750 mm Empty weight: 2200 kg Technical doc.: Yes Message: The Engine was changad in 2013 Condition: Used Price: On demand

Condition: used, Used Jenbacher JMS 612 GS-N.L Gas-Powered CHP Plant Manufactured in 2011, this combined heat and power (CHP) plant is currently configured for tri-generation — producing cooling, heating, and power within a single integrated process. Cooling is achieved via absorption chillers. Isdpfxsw T Rg Te Aacsbc Technical Specifications: Electrical output: 2,004 kWel Thermal output: 4,551 kWt Fuel consumption: 479 Nm³/h of natural gas Gas flow rate: 2.79 kg/s Exhaust gas temperature: 410 °C Engine speed: 1,500 rpm Inlet air temperature: Ambient +10 °C Frequency: 50 Hz Voltage: 6,300 V Included Equipment: Heat Recovery Boiler — Water tube design; gas flow 2.79 kg/s; inlet temperature 410 °C; outlet temperature 120 °C; water outlet 101 °C; water inlet 90 °C; recovery capacity 953 kWt. Absorption Chiller — Refrigeration capacity 1,000 kWt; hot water flow 78.5 m³/h. Plate Heat Exchanger — Constructed from 316 stainless steel; designed for producing hot process water using hot water recovered from the boiler. Air Cooler — Ensures stable engine operation and optimized thermal efficiency. Cooling Tower — Supports effective heat dissipation for continuous tri-generation performance. More technical details, drawings, and operational data are available upon request.

Condition: used, Year of construction: 2001, operating hours: 22,500 h, machine/vehicle number: 27097822024901, Hereby I offer a CHP with the original Master Control control. This CHP has always been at a university and has run on natural gas. The CHP has been dismantled and is now in a heated warehouse and can therefore be picked up immediately. The control cabinet has been disconnected from the engine. Everything is documented so that the control cabinet can be easily reconnected to the engine. In addition, there is an indoor soundproof module included. Machine name: Used CHP Manufacturer: ABB Year of construction: 2001 Generator: Stamford Generator: 140 kva Turbo: no Fuel type: natural gas Electrical power: 95 kW Thermal power: 138 kW Operating hours: 22500 Engine type: MAN E2866E Number of cylinders / arrangement: 6 in series. Speed: 1500 rpm Empty weight: 2,750 kg Iodpfx Aaowkaarecsbc

Condition: excellent (used), Year of construction: 2024, functionality: fully functional, machine/vehicle number: 6125, We sell a used CEVISA beveling machine CHP-60G INV, MFG 2024, SN: 6125 60 mm bevel length; capability in one run: 28 mm bevel length; bevel finish: machined (milling head); adjustable bevel speed depending on the material; optimum beveling speed: 500 mm/min; continual plate fixing pressure system: 4 Bar; 3 feeding rollers always in contact with the plate; 1 roller positioned in the cut-off point to insure: - no vibration; no noise; -smooth and unchanging finish; portable milling machine; mobile and stable; adjustable working height with pneumatic lifting system; electronic bevel adjustment; display: high precision; built-in adjustable bevel angles from 15º to 70º * Nominal thickness: from 10 mm to 100 mm. Motor: three-phase; motor power: 5 CV – 3.8 kW; voltage: 220/380 V. 50 Hz; 250/440 V. 60 Hz; 32 A plug, cable diameter: 2.5 millimeters, maximum consumption of the machine: max. 15A. Electric box with: thermomagnetic switch trip +emergency stop button net weight: 800 kg; works height: adjustable from 760 to 940 mm; built-in trolley; bevel blueprint; plate beveling: K, V, X and Y bevels, bevel speed: 0,5 m/min, three-phase motor: three phases and earth. no neutral, motor power: 5 hp - 3.8 kW, air flow rate 200 l/min. Electrical box: with under voltage trip, emergency stop button, magneto-thermal protection; net weight of the beveling machine: 800kg, working height: adjustable from 760 to 940 millimeters. Integrated carriage. Price: 42.840 Euro + VAT, negotiable , FCA Oradea/Romania Irrtum, Anderungen und Zwischenverkauf vorbehalten / Subject to errors, changes and prior sale / Ne rezervăm dreptul la greșeli, modificări și vânzare prealabila. Ibodpfxjv Ef Rye Aacec We speak English. /Wir sprechen Deutsch./ Beszélünk magyarul. /Nous parlons français/Vorbim romana

Condition: new, Year of construction: 2023, functionality: fully functional, machine/vehicle number: HE-PG378-B/964/140917 - kogeneracja, overall weight: 26,100 kg, fuel type: gas, output current: 682 A, output voltage: 400 V, output frequency: 50 Hz, type of output current: three-phase, continuous power (apparent): 500 kVA, total length: 12,190 mm, total width: 3,000 mm, total height: 3,300 mm, rotational speed (max.): 1,500 rpm, motor manufacturer: Perkins, type of cooling: water, Gas / Biogas Power Generator Module / CHP HORUS type: HE-PG378-B equipped with a turbocharged PERKINS 4006-23TRS2 engine (module);\nYear of manufacture: 2023 (as stated on the HORUS-ENERGIA Sp. z o.o. manufacturer's nameplate);\nAt the Investor’s request and for an additional fee, the module can undergo a commissioning inspection, and comes with warranty and service provided by the manufacturer – HORUS ENERGIA Sp. z o.o. – for one year or up to 8,000 operating hours, depending on the Investor’s preference.\nRated electrical output: 378 kW (410 kW thermal output);\nModule manufacturer: HORUS-ENERGIA Sp. z o.o.;\nService history: (brand new unit);\nEngine hours: 0 (brand new);\nCurrently located in central Poland;\nThe generator set is installed in an enlarged 40 ft sound-attenuated container;\nContainer divided into three sections: control room, engine room, and a section for parallel operation with a second power source;\nEquipment: standard installation for combined power and heat generation + MUZG controller (Gas Mixing Supply System) + provisions for operation with a second power source (i.e., shaft for mechanical power extraction/input),\nFuel: natural gas / LNG (after regasification), biogas (from landfill, wastewater treatment plants, agricultural, or industrial biogas plants), mine gas (methane drainage), (Methane content: 30 Vol.% < CH4 < 100 Vol.% - methane content ranging from above 30% to below 100% by volume.);\nPerkins – technical data sheet available via the link below;\nManual + DTR (Technical and Operational Documentation) + further documentation (technical data) available upon request after email confirmation of purchase interest;\nPhotos of the genset + nameplate: available via the link below;\nGas / Biogas Generator Set / CHP unit is ideal for use as a primary or backup power source, for island operation setups, or in various types of businesses, such as CHP plants, heat plants, agricultural/landfill/waste/industrial biogas plants (e.g. wastewater treatment plants), mines extracting methane for energy use, industrial facilities requiring compressed air supply (working in tandem with compressor systems), or as a power generator for the electricity grid, in dairies, breweries, sugar factories, or applications requiring fuel flexibility. Ibjdpfx Aajw Ihudjcoc

Condition: used, Year of construction: 2001, operating hours: 9,000 h, functionality: unexamined, CHP in insulated container Plant control cabinet Ibedjtrfhrepfx Aacec CHP control cabinet Gas flare Agitator Emergency cooler Various pipes and small parts System was only in operation for 1 year See photos for condition

Condition: used, Year of construction: 2005, operating hours: 140,000 h, Name: CHP used Manufacturer: Köhler / Ziegler Type: SY 53 GSM Year built: 2005 Generator: Leroy Somer Generator Type: LSA44.2S7/4 Generator kW: 132 kVA Turbo: No Fuel type: Sewage gas Electrical power: 53 kW Thermal power: 87 kW Driving force: MAN E0836 E302, 6 Zylinder, 56kW Dimensions: L 3.600 x W 950 x H 1.750 mm Empty weight: 2.200 kg Technical doc.: Yes Message: The engine was changed in 2013 Condition: Second hand Price: On demand Ibsdpfswyaxgjx Aacoc

Condition: ready for operation (used), Hydraulic fixed angle notching machine COMA CA MOD. CHP 260. Two workstations: notching machine + punching machine. Blade length: 260 mm. Work surface: 850 x 700 mm. Workable thickness: 6 mm No. 4 blank holder pistons. Punching: Power T 14 Ijdewhpg Aopfx Aacsbc Weight: 1300 kg Use and maintenance manual.

Condition: new, Year of construction: 2025, operating hours: 10 h, functionality: fully functional, input voltage: 400 V, rotational speed (min.): 1,500 rpm, warranty duration: 12 months, nominal power: 1,000 kW (1,359.62 HP), input frequency: 50 Hz, continuous power: 1,000 kW (1,359.62 HP), Gas generator or cogeneration 1000kW. 40ft container including cooling system. Engine MWM TCG 3016V16S, Generator LSA, MCB - ABB or Schneider, gas line Dungs, control system ComAp or Deiff. Delivery 30-90 days. Isdjvta A Hepfx Aacjbc

Condition: excellent (used), Year of construction: 2024, functionality: fully functional, machine/vehicle number: 6119, We sell a used CEVISA beveling machine CHP-60G, MFG 2024, SN: 6119 60 mm bevel length; capability in one run: 28 mm bevel length; bevel finish: machined (milling head); adjustable bevel speed depending on the material; optimum beveling speed: 500 mm/min; continual plate fixing pressure system: 4 Bar; 3 feeding rollers always in contact with the plate; 1 roller positioned in the cut-off point to insure: - no vibration; no noise; -smooth and unchanging finish; portable milling machine; mobile and stable; adjustable working height with pneumatic lifting system; electronic bevel adjustment; display: high precision; built-in adjustable bevel angles from 15º to 70º * Nominal thickness: from 10 mm to 100 mm. Motor: three-phase; motor power: 5 CV – 3.8 kW; voltage: 220/380 V. 50 Hz; 250/440 V. 60 Hz; 32 A plug, cable diameter: 2.5 millimetres, maximum consumption of the machine: max. 15A. Ibedjv Ed N Ijpfx Aacjc Electric box with: thermomagnetic switch trip +emergency stop button net weight: 800 kg; works height: adjustable from 760 to 940 mm; built-in trolley; bevel blueprint; plate beveling: K, V, X and Y bevels, bevel speed: 0,5 m/min, three-phase motor: three phases and earth. no neutral, motor power: 5 hp - 3.8 kW, air flow rate 200 l/min. Electrical box: with under voltage trip, emergency stop button, magneto-thermal protection; net weight of the beveling machine: 800kg, working height: adjustable from 760 to 940 millimeters. Integrated carriage. Price: 39280 Euro + VAT, negotiable , FCA Oradea/Romania Irrtum, Anderungen und Zwischenverkauf vorbehalten / Subject to errors, changes and prior sale / Ne rezervăm dreptul la greșeli, modificări și vânzare prealabila. We speak English. /Wir sprechen Deutsch./ Beszélünk magyarul. /Nous parlons français/Vorbim romana

Condition: ready for operation (used), Year of construction: 2015, functionality: fully functional, The Spanner plant consists of the cogenerator and the reformer. The reformer, the heart of the wood chip system, produces natural wood gas from wood chips through a controlled process. This gas is used to operate the cogenerator. The generated thermal energy can be used to heat buildings, drying plants or district heating networks, while the electricity is fed into the grid. Ibedpfx Aaswvhf Tscsc Model: HK45 Electrical performance: 45 kW Thermal performance: 120 kW Wood chip consumption: 45 kg/h Requirements for wood chips: Grain size G30-G40 Maximum moisture 15% Fine dust (

Condition: used, functionality: fully functional, The closing machine model 6.000 CPH has been designed to close TWIST-OFF, PRY-OFF, DP, DTP ET DTO lids on glass jars of any size and shape commonly used in the food industry (cylindrical, oval or irregular). Ibjdpewn Dhnefx Aacec

Condition: used, Year of construction: 2003, Name: Used compact CHP module Manufacturer: Sokratherm Type: FG 114i Year built: 2003 Generator: Leroy Somer Generator Type: LSA 46.2 Turbo: Yes Fuel type: Digester gas Electrical power: 114 kW Thermal power: 186 kW Efficiency: Nominal power of 95.4% Hours of operation: 57.460 hrs Driving force: 130 kW. Engine type: MAN E2876 TE 302. Combustion system: Gas-Otto engine. Number of cylinders/arrangement: 6 in line. Speed: 1500 rpm Dimensions: L 2.700 x W 950 x H 2.300 mm Empty weight: 2.750 kg Message: Electrical power: 114 kW. Thermal power: 186 kW Condition: Second hand Ibsdpfx Aajwhwpfjcoc Price: On demand

Condition: used, Year of construction: 2012, operating hours: 101,000 h, functionality: fully functional, machine/vehicle number: MAN E 0836 E 312, fuel type: gas, power: 48 kW (65.26 HP), output voltage: 400 V, output frequency: 50 Hz, Used BIOGAS CHP unit with protective cover. A cylinder head service was performed in 2023 at 81,000 operating hours. Ibedpfewmld Uex Aacjc

Year of construction: 2025, condition: new, functionality: fully functional, Complete - New MWM GAS generator set, CHP as option, Generator 10500V/50Hz Ibjdpfx Aov Uag Ijacoc

Condition: new, Year of construction: 2025, pressing force: 150 t, table width: 1,000 mm, table length: 3,100 mm, Equipment: safety light barrier, PLACE OF PRODUCTION: TURKEY WARRANTY PERIOD: 24 MONTHS DELIVERY FROM STOCK 2025 MODEL NEW AND UNUSED 150 TONS H TYPE HYDRAULIC PRESS TECHNICAL SPECIFICATIONS TYPE STEEL CONSTRUCTION, 8 SLIDE H PRESS BODY TYPE BODY MATERIAL St52 – ERDEMİR CAPACITY (RAM) 150 TONS MOVABLE TABLE DIMENSIONS 3100 x 1000 mm FIXED TABLE TABLE DIMENSIONS 3100 x 1000 mm PARALLELITY TOLERANCE 120 micron/mt. PERIPHERALITY TOLERANCE 60 micron/mt. STROKE (RAM) 600 mm MIN. INTERMEDIATE SPACE 100 mm MAX. INTERMEDIATE SPACE 700 mm WELDING STRESS REMOVAL Stress relief by vibration WELDING APPLICATION - EN ISO 15614-1/2017 welding application certificate accredited by TÜRK-AK and approved by WPQR and WPS. (Welding applications are supervised by “welding coordination engineers” certified according to EN ISO 14731) MAX. WORKING PRESSURE 250 Bar TOTAL MOTOR POWER 22 kW– IE3 MAIN PUMP 37 cm³ – PARKER MOVING TABLE FAST Descent Speed 140 mm/sec. MOVING TABLE SPINNING SPEED 14 mm/sec. MOVING TABLE RETURN SPEED 170 mm/sec. MAIN CYLINDER INNER DIAMETER Ø 160/120 mm – Ck45 – 3 pcs. ASSISTANT CYLINDER INNER DIAMETER Ø 90/70 mm – Ck45 APPROXIMATE HEIGHT OF PRESS 4000 mm APPROXIMATE WIDTH OF PRESS 3500 mm APPROXIMATE DEPTH OF PRESS 2000 mm LOWER TABLE HEIGHT FROM THE GROUND 1000 mm PRE-FILL VALVE NG 80 – 3 pcs. Iodpfsv Inrlex Aacjbc HYDRAULIC UNIT PARKER COOLING SYSTEM SUCTION – CIESSE ENGINE CLASS USED FOR THE UNIT IE3 LEVEL INDICATOR PARKER AIR FILTER PARKER – 10 MICRON PERMEABILITY RETURN FILTER PARKER – 25 MICRON PERMEABILITY OIL AND HEAT INDICATOR PARKER VALVES USED PARKER LUBRICATING STYLE AUTOMATIC – (ADJUSTABLE FROM THE SCREEN) RAM STROKE ADJUSTABLE FROM THE SCREEN RAM TONNAGE (PRESSURE) ADJUSTABLE FROM THE SCREEN SYSTEM ERROR INFORMATION CAN BE SEEN ON THE SCREEN PRESS STATUS INFORMATION SCREEN VISIBLE ON THE SCREEN MOULD MEMORY CAN BE ADJUSTED FROM THE SCREEN HYDRAULIC UNIT OIL TEMPERATURE INFORMATION CAN BE VISIBLE ON THE SCREEN LINEAR DISTANCE SCHEDULE NOVATECHNIK PLC APPLICATION DELTA TOUCHSCREEN PANEL DELTA 7 ‘’ SWITCH MATERIALS SIEMENS – SCHNEIDER APPROXIMATE WEIGHT 20 TONS