Used Tube Polishing Machine for sale (85,524)

Condition: new, functionality: fully functional, Year of construction: 2025, laser power: 6,000 W, travel distance X-axis: 6,000 mm, positioning speed: 100 m/min, input voltage: 380 V, input frequency: 50 Hz, type of input current: three-phase, total length: 6,000 mm, warranty duration: 24 months, Equipment: CE marking, centralized greasing system, cooling unit, dust extraction, fume extraction, nozzle changer, safety light barrier, 3 Chuck Professional pipe laser cutting machine (GS-6022HG) Working area (L/W): 6000mm*φ220mm Repeat positioning accuracy: ≤0.03mm Max. positioning speed: 100m/min Max. acceleration: 1.0G Max. rotating speed of chuck: 110r/min Machine weight: 10T Ijdpevrwt Tjfx Aa Estr Round pipe: Φ15mm-Φ220mm Square pipe: 15mm*15mm ~ 150mm*150mm Rectangular pipe: 30*20mm~160*80mm Oval tube/flat oval tube: Short axis≥15mm, long axis≤210mm Channel steel: Max 20# I-beam: Max 18# H steel: Max 175*90mm Supports high-precision cutting of round tubes, square tubes and special-shaped tubes. Flexibly adapts to different specifications of tubes.

Year of construction: 2016, condition: ready for operation (used), A centerless round polishing machine Loeser is available. Workpiece diameter range: 10mm-30mm, workpiece length range: 100mm-1000mm, stations: 2, working direction: left-right, magazine system with infeed and outfeed table: 1000mm/1000mm. Including magazines as well as infeed and outfeed table. Documentation available. An on-site inspection is possible. Itsdpfxsvzbg Aj Aa Esr

Year of construction: 2025, operating hours: 5 h, condition: refurbished (used), functionality: fully functional, machine/vehicle number: I 91-61, USED AND REFURBISHED MACHINE (AS NEW): • Usable working length: 2100 mm • 40 mm front stop for overlapping processing • Maximum block thickness: 140 mm • Working capacity at 90°: 2100 x 140 mm • Electrospindle power: 1.2 kW Itsdpfxox Da Dhe Aa Esr • PLC electronic sequential control • 3.5” touchscreen controls • Rapid belt drive with Brushless motor • Epicyclic reducer Complete with: • 8 pressure shoes • 2 front supports • 1 side square • 1 service wrench Supplied with a set of new polishing tools (with three synthetic diamond tips)

Condition: good (used), Year of construction: 2002, functionality: fully functional, type of input current: three-phase, For sale is a grinding-polishing machine. It can be connected to a dust extractor. Little used, in working order. Itodova Elgopfx Aa Esr

Condition: used, Year of construction: 1988, gebraucht 1988 090151 prompt, Zwischenverkauf v Italien 12800 € 1 42 mm 4665 mm 800 mm 1160 mm 1470 kg 42 x 2,5 mm 40 x 1,2 mm 30 x 40 x 1,7 mm 40 x 30 x 1,3 mm 255 mm 22 mm 180 ° 90 °/s 5,5 kW 120 l Capacity specifications refer to 400 N/mm² Maximum bending radius with pipe guide rollers: 255 mm Maximum bending radius with pipe guide slide: 175 mm Iodpfexx A Ekox Aa Eetr Minimum bending angle: 4° Maximum usable length without positioning device: 3900 mm Maximum usable length with positioning device: 3370 mm Adjustable mandrel extension travel from 8 mm Opening and closing travel of the counter-clamping jaws: 0-45 mm Opening and closing travel of the rollers or slides: 12-22-42 mm Operating manual in German Machine does not comply with AMVO or UVV regulations Tools not included

Condition: like new (used), Year of construction: 2021, operating hours: 8 h, functionality: fully functional, type of input current: three-phase, 2011 Rigao Machinery Corp Plastic/PE/Laminated Tube Labeller and Tube Filler & Sealer with Cooler This machine is in "as new " condition only running a few thousand tubes for commissioning. It was purchased for a specific purpose, which did not materialise. The system can be run separately (labeller and Filler/Sealer) or as one continuous line. Comes with original tool kit, spares and the option of a 12 month warranty through a UK Based Rigao Specialist. This same company could potentially commision the machine if required (price on application). Plastic/PE/Laminated Tube Filler and Sealer with Cooler ○ The machine is used to fill and seal plastic tube, capable of tube loading, tube code registering, filling, hot air sealing, code printing, trimming and feeding off line a finished tube. ○ Machine contacting parts are made of 316L stainless steel which is clean and sanitary. ○ With a built in safety device, the machine will be shut down if the door is open. There is also an overload protection provided. Parameter Filling volume 5-250ml（by changing different filling system） Filling accuracy ≤±1% Capacity 1800-2400pcs/hour (Depend on tube size and product viscosity） Tube diameter ф13-50mm (by changing tube tooling – 35, 40 & 50mm tooling available). Tube length 210mm (Max. Length) Hopper volume 40 L Power 380V /50Hz 3Phase Air pressure 0.5-0.7MPa Equipped motor 1.1 Kw Plastic/PE/Laminated Tube Labeller with Auto Feeder Tube size： Φ20-50mm，Length: 20-240mm Mandrel sizes: Φ35mm, Φ50mm Labelling speed： 60-100 tubes/minute（vary with tube and label size） Labelling accuracy： ±0.5mm（excluding tube or label difference） Label size： ID: Φ75mm; OD: Φ300mm; Width: 170mm Compressed air： 0.4-0.7Mpa，3L/min. Power supply： 220VAC±5% 50/60Hz 1.2Kw Machine dimension： (L)2,252×(W)1,350×(H)1,875 Configuration list: S6120 servo label out Japan Yaskawa Isdpst Ami Uofx Aa Estr Label detecting eye Japan Keyence Tube detecting eye Japan Keyence Label roller motor transmission Japan Panasonic Stuck tube clearing device Japan Panasonic High precision CAM divider Taiwan RU80DF Pressure roller wheel device Japan Panasonic PLC control system Germany Siemens Touch screen Taiwan Weinview

Condition: new, Cesurbend Mandrel Bending Machine / Tube Bending Machine PBNC-65 Technical Specifications Max. Tube Diameter (mild steel): 63 mm Max. Tube Wall Thickness (mm): 3 Max. Bending Angle (°): 190 Itodext Rdwspfx Aa Eer Tube Bending Rate (rpm): 7–10 Max. Hydraulic Pressure (bar): 200 Max. Bending Radius (mm): 250 Min. Bending Radius (mm): 45 Tube Length (mm): 3500 Bending Tolerance (mm): ± 0.25 mm Bending Motor Power (kW): 7.5 Hydraulic Motor Power (kW): 4 Oil Tank Capacity (L): 50 Machine Width (mm): 1450 Machine Length (mm): 4250 Machine Height (mm): 1200 Machine Weight (kg): 1600 Features • 4-way adjustable gauge • Chain bending system • Gear motor • Touchscreen control panel • Foot pedal operation • Hydraulic mandrel movement • Hydraulic damping function • Hydraulic compression function • Hydraulic pusher • Four cylinders • 7" touch color display • 15 sequential twist positions • 100 program memory capacity • Omron PLC control

Condition: new, Year of construction: 2024, Complete set double use laser machine ( 3 and 6 Kw in stock ) sheet metal 3015 ( 3 x 1,5 meter ) Tube 15 to 240 mm diameter tube length 6,3 meters include necessary options for a perfect laser line. include 1 filter installation ( cutting air can leave in factory ) include anty fire box. include Vacuum lift for sheet metalplate 800 kg load. no cable unit work on battery in vacuum unit. include 1 compressor for 16 BAR it give posibility to cut steel without gas. for quick cutting and SST steel it save lot of air and can increase the cutting feed consummeble for long time cust free cutting time. Itsdpfonqzb Iex Aa Ejr include vacuume lifter from 800 Kg lifter work on battery in lifter box so with loading machine no cables around you special for save working arear. all in one price. installation, training by professional service team on request

Condition: new, – Capacity: 34 x 3 mm Ijdpfx Asxq Hl Eea Eotr – Digitally adjustable stroke – Emergency stop switch – With 3 tool sets: 33.7 mm, 21.4 mm, 16 mm – Documentation – Weight: 80 kg – 400V

Condition: excellent (used), IMM 72780 Double-sided polishing machine Mint condition, the machine has hardly been used. Itodpfxeu Hanye Aa Eer TECHNICAL DATA Polishing wheel: 100 - 500 mm shafts: 35 mm Spindle speed: 1500 rpm Voltage: 400 V, 50 Hz Weight of basic machine: Approx. 400 kg No responsibility is taken for the correctness, completeness and up-to-dateness of the information.

Condition: reconditioned (used), Round table polishing machine make Bula, model MP81 for sale. Continuously turning machine for polishing, brushing, grinding and deburring a wide variety of workpieces. 6 workpiece holders mounted in a pitch circle of 250 mm. 1 processing station, drive power 2.2 kW, with Bula Quick Lock system of the polishing wheels. Polishing shaft diameter 25 mm The machine has been completely overhauled, machine body sandblasted, primed, repainted, new bearings, new motors, new gearbox, new V-belts, new handwheels, new pulleys, completely new control cabinet, and all drives are controlled by frequency converters. Iedpjlccvmjfx Aa Eotr Subject to prior sale. Optionally, the system could also be supplied with a polishing paste system - liquid, consisting of 1 high-pressure dosing pistol WIDOBERG HDP-2, brackets, timer, etc. and pressure container.

Condition: used, Year of construction: 2001, Technical details: tube diameter: 74 mm wall strength: 5 mm tube diameter min.: 10 mm tube diameter max.: 74 mm round material: Stahl max: 40 mm control: Trumpf-Rohrtechnik IsoBend 2.0 bending radius max.: max: 300 / min: 65 mm Iodpfxou Ibvhj Aa Ejtr bending angle max.: max: 195 / min: 0,1 ° bending speed: (°/s): 90 / (°/s²): 190 °/s tube pipe draw up length: 3000 mm work pressure of hydraulic: Betriebsdruck max: 300 bar total power requirement: 43 kVA weight of the machine ca.: 8,5 t dimension machine xH: 6,5 x 1,6 x 1,6 m dimension control panel: 0,8 x 0,6 x 1,4 m It is a multi radius bending machine with bending head and swivel arm. (Cold bending machine) Possible applications: only for processing pipes, round steels and wires made of steel, stainless steel and non-ferrous metals. Due to the cross slide of the bending head, the following advantages can be listed: -free programmable X and Y axes -level change cross slide: tical travel = 300mm (vert. position freely programmable) and max. horizontal movement 350mm -Bending forms of different sizes within a stack of bending forms can be approached as required. The bending direction is to the right. Control software Trumpf-Rohrtechnik IsoBend 2.0 Hydraulic unit with high-pressure multi-flow pump Mandrel retraction unit Slide rail (speed max. 362mm/sec. and acceleration max. 1100 mm/sec.) i.D. *

Condition: new, Cesurbend Mandrel Tube Bending Machine / Pipe Bending Machine PBNC-51 Technical Specifications Max. Tube Diameter: 51 mm Max. Tube Wall Thickness (mm): 3 Max. Bending Angle (°): 190 Tube Bending Rate (rpm): 7-10 Max. Hydraulic Pressure (bar): 200 Max. Bending Radius (mm): 250 Tube Length (mm): 3000 Bending Motor Power (kW): 5.5 Hydraulic Motor Power (kW): 3 Machine Width (mm): 1400 Machine Length (mm): 4215 Machine Height (mm): 1450 Machine Weight (kg): 1600 Features • In this process, the jaw clamps the tube after it is inserted into the machine. The tube is bent over the die to half its diameter. When using a mandrel and wiper, better results are achieved for bends requiring higher quality, with thinner wall thickness and smaller radii. • This is a three-piston machine with a hydraulic spool located behind the hydraulic boom. Iodpext Rc Tsfx Aa Eetr

Condition: used, Polish Lathe / Polishing Machine Between points: 1500 mm Centre height: 180 mm Maxi diameter to polish: Ø 380 mm Spindle CM3 Spindle speed driven by speed variator Iodexuf Hvopfx Aa Ejtr Pneumatic tailstock Equipped with a vaccum system (only air hose to plug in) Machine was used to polish axes Voltage: 220 V mono Dimensions (L x W x H): 3200 x 1000 x 1900 mm Weight: 1,2 T

Condition: good (used), Manufacturer: Tracto Technik Type: TUBOMAT Year of construction: 1996 Pipe bending machine with electric control, 4-fold bending angle pre-selection and digital display Hydraulic bending drive operated by hand lever valve Hydraulic bending drive, operated by hand lever valve Follower-type pressure die (sliding guide) Hydraulic mandrel retraction Pipe circular saw with coolant lubrication and automatic feed Pipe deburring unit for internal and external deburring Hydraulic power unit as basic seating for attaching a cutting ring assembly or flaring device Machine mobile and flexible to use Specifications Metric US Standard Max. Product Ø 42 mm Min. product Ø 6 mm Max. Wall thickness 3 mm Max. Bending radius 5 mm Min. bending radius 180 mm Isdpst Dk Uksfx Aa Ejtr Max. Bending length 2000 mm Deburring device Yes Sage device Yes Flanging device Yes Dimensions (estimate) Length 3500 mm width 1000 mm height 1200 mm weight 1000 kg Please note: The information on this page is given in good faith and to the best of our knowledge, and where possible, has been obtained from the manufacturer, but accuracy cannot be guaranteed. Accordingly, it does not constitute a representation or contract and we recommend that you check all relevant details.

Condition: good (used), functionality: fully functional, Year of construction: 1998, bending radius (max.): 600 mm, mandrel length: 1,200 mm, wall thickness: 8 mm, Transfluid DB 40100ST Mandrel bending machine Tube bending machine The above machine is a mandrel bending machine designed exclusively for the production of tubes and profiles with an outer diameter of 40-100 mm, max. 110x5 mm with a max. wall thickness of 8 mm or for the processing of solid materials with an outer diameter of up to 70 mm. Pipe push-on length/usable length: 1200 mm Iedpfjr H Havex Aa Eetr Radius range max:600 mm Bending height:1200 mm Machine data Length:4000 mm Width:2600 mm Height:1400 mm Weight:9000 kg

Condition: used, Year of construction: 1990, Technical details: tube diameter: 42 mm wall strength: 25 mm round bar steel: max. Ø 20 mm square material: Rohr 25 x 25 mm bending radius max.: innen max: Ø 20 und außen max: Ø 170 mm bending speed: keine Angaben °/s tube pipe draw up length: 3000 mm control: Software RC 7000 weight of the machine ca.: 2,8 t dimensions electric cabinet: 800 x 700 x 2000 mm dimension machine xH: 5,1 x 0,7 x 2,0 m Application: Machining of deformable tubes, rectangular tubes and round bars and square tubes. Description of the software RC7000, programming manual rectangular tube 42 x 20 x 2,5mm bending direction to the left Isdpfx Aeu Ibvusa Eotr Operation via control panel with monitor Accessories: -div. bending tools for tube Ø 25mm -12 div. collets -div. auxiliary and clamping devices *

Condition: new, Cesurbend Tube Bending Machine / Pipe Bending Machine PBNC-38 Technical Specifications Max. tube diameter (mm): 38 Max. wall thickness (mm): 2 Max. bending angle (°): 190 Tube bending speed (rpm): 8-10 Max. bending radius (mm): 250 Tube length (mm): 2500 Bending motor power (kW): 3 Hydraulic motor power (kW): 1.5 Machine width (mm): 1400 Machine length (mm): 3250 Machine height (mm): 1200 Itjdpoxt Rctofx Aa Eer Machine weight (kg): 700 Features • 4-position adjustable gauge • Option to use mandrel and spoon on NC machines • The carriage system is equipped with a linear guide rail and carriage • Connection equipment is standard. Mandrel and spoon are optional. • 7" color touchscreen display • 5 sequential twisting options • 100 program memory capacity • Omron PLC control

Condition: used, functionality: fully functional, Year of construction: 1997, 5-axis CNC tube bending machine BLM Dynamo - 0 Serial number: 605970300001 Year of construction: 1997 Voltage: 380V 50HZ Machine weight: 1500 kg Control system: DOC 85C BLM bar loader BLM CARM 7 Serial number: 340040102059 Year of construction: 2004 Weight: 405 kg Without conveyor belt Without protective grid TECHNICAL DETAILS Number of axes: 5 Average output: ~ 2400 bends/h Bending capacity round tube R=45 kg/mm²: 4 - 12.7 x 1.5 mm Bending capacity round tube R=35 kg/mm²: 4 - 14 x 1 mm Bending capacity round tube Al/Cu/Ms: 4 - 18 x 1.25 mm Bar feeder: BLM Carm 7 (year of manufacture: 2004) Positioning speed X-axis: 2000 mm/s Bending speed H/Z Y-axis: 500 °/s Turning speed Z-axis: 900 °/s Turning speed Z-axis: 100 °/s Positioning speed T-axis: 500 mm/s Measuring tolerance X/T axis: ± 0.1 mm Measuring tolerance Y/Z/Q axis: ± 0.1° Maximum range at maximum acceleration X-Y-Z: 1000 mm - 90/90/0° - 0/180/0° with tube 18 x 1.25 mm MACHINE DETAILS Voltage: 380 V, 50 Hz Hydraulic pressure: max. 120 bar Machine weight: 1500 kg Control system: DOC 85C Iedpfxet R Tgio Aa Eotr Ex location Dortmund, free truck loading

Condition: used, Technical details: wheel diameter: 780 mm table height above floor: 800 mm Table dimensions: 890x190 mm grinding table: inclination: neigbar Grad total power requirement: ca. 2,0 kW weight of the machine ca.: 0,2 t space requirements of the machine approx.: L:1,2xB:1,05xH:1,3 m Double Disc Grinding Machine - Its based on a molding machine body foundation as a whole. - application range: metal, wood, plastic Ijdpfx Aaeu Ng Rte Eetr - ginding disc surface diameter:680mm - grinding disc material: sand paper - sucction noozle: 80x120mm *

Condition: new, Cesurbend Mandrel Bending Machine / Tube Bending Machine PBH-32 Technical specifications Max. tube diameter: 32 mm Max. wall thickness (mm): 2 Max. bending angle (°): 190 Tube bending speed (d/min): 8.5 Max. bending radius (mm): 275 Bending motor power (kW): 2.2 Hydraulic motor power (kW): 1.5 Tube length (mm): 2000 Machine width (mm): 1000 Machine length (mm): 2300 Machine height (mm): 1050 Machine weight (kg): 400 Features • Hydraulic clamping Itjdext Rb Njpfx Aa Eor • Brake motor / precision rotation • Manual size adjustment

Year of construction: 1994, condition: used, Technical details: plate thickness: 1,0 mm tube diameter: 60 / 80 / 90 / 100 / 110 / 120 / 130 mm wall strength: 0,6 / 0,7 / 1,0 mm tube pipe draw up length: 150 - 1000 mm control for program: SPS Simatic S 5 air pressure - required: 5 bar voltage: 380 V control voltage: 24 V total power requirement: 3,5 kW dimensions L x W x H: 1,2 x 1,0 x 1,6 m Pipe drawing-in machine, currently equipped for Ø 130mm. - e.g. for furnace pipes Iedpfx Aju Icv Aoa Ejtr -insertion and removal of the workpieces manually -operation via control panel further features: Sheet thicknesses: 0.6 / 0.7 / 1.0mm workpiece length 150 - 1000mm div. Zubehör/Werkzeuge Ø 120 und Ø 130 und weiteres, wie im Foto *

Condition: new, Cesurbend Mandrel Tube Bending Machine / Pipe Bender PBM-32 E Technical Specifications Max. tube diameter (mm): 32 Max. tube wall thickness (mm): 2 Max. bending angle (°): 190 Tube bending speed (rev/min): 8.5 Max. bending radius (mm): 275 Bending motor power (kW): 2.2 Tube length (mm): 2000 Machine width (mm): 1000 Machine length (mm): 2300 Machine height (mm): 1050 Machine weight (kg): 300 Features • 4-way adjustable measuring device Itjdoxt Rbpjpfx Aa Eer • 7" color touch display • 5 sequential rotation options • 100 program memory capacity • Omron PLC control

Condition: used, Technical details: grinding table: inclination: nein Grad voltage: 220 V machine weight approx.: 44 kg space requirements of the machine approx.: 0,3 x 0,45 x 1,1 m Iodpfx Aaeu Ng Sqs Eetr Disc right: Ø 150mm x W: 50mm; disc fitted with emery burrs Disk left: Ø 125mm x W: 50mm; disk equipped with emery burrs support on both sides Machine mounted on stand with base plate. Operation via on/off switch *

Condition: new, Cesurbend Mandrel Bending Machine / Pipe Bending Machine PBM-32 Technical Specifications Max. pipe diameter: 32 mm Max. wall thickness (mm): 2 Max. bending angle (°): 190 Pipe bending speed (r/min): 8.5 Max. bending radius (mm): 275 Bending motor power (kW): 2.2 Pipe length (mm): 2000 Machine width (mm): 1000 Machine length (mm): 2300 Machine height (mm): 1050 Machine weight (kg): 300 Itodpoxt Ra Esfx Aa Esr Features • This is a semi-automatic machine. If you need to bend only a few pipes per day (25-50 pieces per day), this machine is the right choice. • It is the simplest pipe bending machine with brake motor. • Brake motor / precise bending • Manual dimension setting • Former rack