Used Thermoplastic Granules for sale (680)

Condition: good (used), Year of construction: 2004, functionality: fully functional, Manufacturer: HABERMEHL Anlagenbau GmbH Address: Hauptstr.1, 35510 Butzbach-Ebersgöns, Germany Type: EH 400/1 Serial number: 901 Year of manufacture: 2004 Voltage / Frequency: 400 V / 50 Hz Rated power: 3 kW CE-certified: Yes 🛠️ Device Description Industrial shredder or crusher (Shredder/Granulator). Notable features visible in the photos: - System with rotating knives (shredding unit) on a 2 mm shaft - 3 kW SEW motor and reduction gearbox - 8 mm screen (the screen is labeled “8 mm Sieb”) – determines the output particle size - Rollable, portable design - Material discharge container and lower motor drive system Machines of this type are typically used for shredding the following materials: - Plastics - Rubber - Wood - Light metal chips - Electronic scrap 📝 Technical information you should request If you require further details, you may request the following information from the supplier or manufacturer: Iasdpfxsw Niuho Ag Ujl

Condition: excellent (used), Screening and sorting machine for bulk materials or small metal components. Very good condition – complete, equipped with original drive, control cabinet, and a set of calibration screens. • Manufacturer: SCHWANOG Günter KG, Villingen / Schwarzwald • Model: RAPID SBM 63G • Year of manufacture: 1972 • Drive: Bauknecht motor 0.55 kW, 380/220 V, 2850 rpm • Control cabinet: Carl Kurt Walther GmbH, Wuppertal • Robust steel construction, stable frame with transport wheels • Power supply: three-phase 400 V • Complete set of screening sieves in wooden frames (numbers 1–6) • Sieve mesh range: from 2 mm to 15 mm • Adjustable and exchangeable screens • Main switch, start/stop controls, and overload protection • Very good condition – dismantled from the plant, mechanically fully functional The machine is ready for operation after a basic inspection. Ideal for: metalworking shops, foundries, industrial laboratories, sorting granulates, sand, or components. Iedpfxoxmt Eqj Ag Ueal

Condition: good (used), Year of construction: 2010, Arburg 570 H 2000-400 (2010) Clamping force: 200 t Screw diameter: 35 mm Shot weight: 141 g Distance between tie bars V: 570 mm Distance between tie bars H: 570 mm Shot volume: 154 cm3 Screw stroke: 160 mm Injection pressure: 2000 bar Type: Horizontal Drive: Hybrid Equipment: Iodpfjwpkfcsx Ag Ujal Thermoplastics cylinder cpl. 35 mm high-wear resistance Drive unit w. 11 kW motor and 21.4 l/min capacity SELOGICA 'direct' controller Air blast system 1 with pressure reducer Interface for robot system (EUROMAP 67), 50-pin AED - electrom. dosage drive 9 electr. heating control circuits for mould heating Interface for colouring device 8 free cooling circuits manually adjustable Position-regulated screw

Condition: good (used), Plummer block housings, bearing blocks for shredders, crushers, water mills, chippers, cutting mills, granulators, and cutting granulators -Quantity: 1 piece heavy-duty steel pillow block housing Iasdpfxodaa Huo Ag Uel -Type: Bearing block, inner diameter: 320 mm -Axis/Center of housing: 190 mm -with: shaft seal discs -Quantity: 1x bearing block available -Suitable for: Bearing abbreviations 22236/22330/23064/23138/23236, not included in the scope of delivery -Suitable for: Bearing abbreviations 22236K/22330K/23064K/23138K/23236K, not included in the scope of delivery -Dimensions: 560/190/H395 mm -Weight: 228 kg

Condition: repair required (used), Year of construction: 2014, functionality: limited functionality, 1 x ActionPac Scales & Automation single-head linear weigher with drop-through metal detector. Supplied with pneumatic foot-pedal for manual depositing. *PLEASE NOTE - THE LINEAR WEIGHER REQUIRES NEW CONTROL PANEL SCREEN* Syntron Magnetic Feeder - F-T01-A. Linear weigher: Model - ME109CM. Serial number - 4284. Date of manufacture - 2014. Weighing range - 28g to 2268g (typically). Feeding pan - smooth, for solid and small granular products. Electrical requirements - 1 phase. Metal detector: Model - IMD-I gravity drop-through. Aperture - 180mm diameter. Isdpfsxv A Itex Ag Uoal Electrical requirements - 1 phase. Overall dimensions - 1420mm long x 975mm wide x 3200mm high. Previously used to weigh and pack coffee beans and granules. Cost of new control panel - $2,700 (quoted by manufacturer).

Condition: used, power: 160 kW (217.54 HP), GETECHA RS 8012 Granulator Accessories: with used control cabinet Drive: 160.0 kW Rotor blades: 7x2 Isdpfxjx H Nxio Ag Ueal Stator blades: 4 Rotor diameter: 800 mm Rotor width: 1200 mm Feed opening: 1200 x 950 mm

Year of construction: 2014, condition: refurbished (used), functionality: fully functional, Machine for recycling scrap cables. The ideal machine for processing mixed copper cables without plugs, up to approximately 150 kg per hour. Thanks to two integrated separators, you can simultaneously produce heavy grade 1 granulate and fine granulate from stranded wires in a single operation. Cables can be fed manually or automatically via a conveyor belt (if available). The system has been completely refurbished by us and is in very good condition. You are welcome to inspect and test the machine at our facility. We sell this system with a 12-month used machinery warranty. Isdpfx Agjx R R Iye Ueal

Condition: excellent (used), Professional granulator from the German brand Dreher – model S 26/26 GFS-SPEZIAL. This unit is designed for shredding plastics from injection molding or extrusion processes. Robust construction, proven VEM 7.5 kW motor, three-phase 400 V power supply. The machine features a large feed hopper, convenient service access, and an electrical control cabinet with emergency stop button. The installed low-speed three-phase motor ensures high shredding power with stable operation. Iasdpfx Agevyumyo Uol • Motor power: 7.5 kW • Power supply: 400 V 50 Hz • Speed: 1500 rpm • Throughput suitable for medium and large injection moulding machines • German manufacturing quality • Sturdy frame and knife assembly Very good condition, mechanically inspected, ready for operation.

Condition: used, Year of construction: 2006, (2006) Arburg 420 C 800-350 DUROPLAST Clamping force: 80 ton Screw dia: 40mm Weight 3400 kg Machine used for Bakelite production (DUROPLAST) Iodpfeuy Sdtox Ag Usal

Year of construction: 1995, condition: good (used), Single-shaft shredder, waste shredder, cutting mill, auxiliary mill, granulator, shredder, plastic shredder, granulate mill, granulator, rotor mill, recycling technology -Condition: Single-shaft shredder is equipped with a good set of blades. -Manufacturer: Vecoplan, Side-mounted mill cutting mill -Type: VAZ120/105 -Processing capacity: 200-3000 kg/h -Number of sieves: 2 pieces Ø20 mm, Ø30 mm -Drive motor: 18.5 kW -Number of cutting blades: 27 pieces -Number of counter blades: 1 piece -Inlet cross-section: 1240 x 1075 mm -Rotor width: 1075 mm -Rotor diameter: 230 mm Ijdpfxsxlcqto Ag Uoal -Dimensions: 2000/2700/H2370 mm -Weight: 2800 kg

Condition: used, Used Zanchetta model Rotolab stainless steel mixer granulator. Total bowl capacity 2.8 litre, working capacity approx. 1.6 litre. Has jacketed bowl with inside dimensions 160 mm diameter x 140 mm height. Main impeller rotation speed 120 - 1200 rpm driven by electric motor. Chopper blade rotation speed 6000 rpm driven by electric motor. Includes local control panel and integrated switchboard, connection for vacuum and nitrogen (.). Iasdpox Ryupjfx Ag Uel

Condition: good (used), Year of construction: 2001, functionality: fully functional, machine/vehicle number: 184686, clamping force: 1,000 kN, screw diameter: 25 mm, clearance between the columns: 420 mm, displacement volume: 54 cm³, injection weight: 45 g, For sale is an injection moulding machine from the brand Arburg, model 420 C 1000-150/60. The machine is in excellent technical condition and has been very well maintained. The machine is offered without peripherals. The rotary table, material feed, temperature control units, and other accessories are not included. Technical data: Iaodpfsx E U Elex Ag Ujl Year of manufacture: 2001 Clamping force: Clearance between tie bars: 420 x 420 mm Opening stroke: 500 mm Mould installation height: 250 mm Mould mounting plate: 570 x 570 mm Ejector stroke: 175 mm Screw diameter: 25 mm Theoretical shot volume: 54 cm³ Shot weight: 45 g/PS Transport and loading can be organised on request, at an additional cost, Europe-wide. All prices are subject to VAT. Inspection by appointment is possible. Please contact us—our team is happy to assist you. Trade-in or exchange possible! Machinery purchase / sale BUYING / SELLING PRODUCTION & METALWORKING MACHINES AND MORE Are you looking for a high-quality yet affordable metalworking machine for your production? Or are you looking to sell yours? For further information or contact options, please visit our website.

Condition: refurbished (used), Year of construction: 2015, BOHLE Vagumator® VMA 300 V batch granulator This intensive mixer-granulator is designed for the production of wet granulate with subsequent vacuum drying in batch sizes of 40–130 kg. In 2010, a HYFRA VWK 70/1-S cold water treatment unit was retrofitted for the vacuum condenser, with a cooling capacity of 6.6 kW at 32°C. Ijdpfoxvzblex Ag Ueal In 2015, the entire machine and process control system was replaced. In 2015, two Single Advanced N1-90-18-80 temperature control units were installed, each with a heating capacity of 18 kW and a cooling capacity of 80 kW for water up to a maximum temperature of 90°C. Manufacturer: L.B. Bohle

Condition: used, Manufacturer CONDUX Model CS 450/600-2 Hollow body granulator and secondary granulator for pre-shredded material Rotor: 450 mm diameter x 600 mm working width 5 rotor blades (angled cut), 2 stator blades Drive motor 22 kW Ijdpfjxgtl Rjx Ag Ujal

Condition: ready for operation (used), functionality: fully functional, A good used vacuum transfer system from CFM with lance hose and discharge station in Stainless Steel - requires three phase power and compressed air - ideal for handling powders granules or pellets More videos and pictures available - just ask Iodpfx Agowv Tzge Ujal Ready to ship worldwide We will handle shipping and export documentation

Condition: excellent (used), Year of construction: 2010, operating hours: 2,125 h, functionality: fully functional, MG Recycling – Copper Cable Granulation Line Manufacturer: MG Recycling Model: Matrix 400 Complete Cable Granulation Line Condition: Excellent – Fully operational Availability: Immediate Technical Description: Cable granulation line including: • Fully rebuilt pre-shredder (recent overhaul) o All rotor bearings replaced o Gearbox bearings replaced Iaedpex It N Ujfx Ag Uol • Conveyor with magnetic rollers for scrap separation • Dosing hopper • Feed conveyor • Blade mill with 3 / 4 / 5 mm calibration screens • Separation by cyclone and zig-zag separator • Finishing turbo • Densimetric table • Dust extraction with bag filter Spare parts included: • Pre-shredder: 1 set of knives + counter-knives • Blade mill: 3 sets of blades and counter-blades Capacity: ≈ 200 kg/h finished product Application: Copper cable processing and recycling Price: €120,000 (complete processing line) Additional information: • Installation can be seen in operation • Photos and further details available on request 📩 Contact us for more information

Year of construction: 2026, condition: new, Do you want the BEST price/performance ratio? Contact us! Machines direct from the manufacturer! THE ORIGINAL MADE IN AUSTRIA! DUOFORMER - Heating – Forming- Pressing! The HEATING UNIT for all thermoplastic materials up to 230°C and The VACUUM PRESS for daily use! • No tricky placing of pressing layers • No sliding of the former • effortless closing and opening • pressing of M-shapes • operating from all 4 sides DUOFORMER S VERTICAL- Producing without compromises! Now on sale! Vertical opening: work piece height up to 850 mm Clamshell opening: See other sales offer on this platform! Pressing surface LxW: 2880x1280mm Heating surface LxW: 2600x1250mm Overall dimensions LxWxH: 3400x1750x1500mm • Heating drawer +230°C – 16kW • 40 m³/h high performance vacuum pump (BECKER) • 4 FESTO pneumatic-cylinders • Trussed pressing frame • Two hand safety operation • Motion signal Equipment: Vacuum table with silicone membrane and MEMBRANE FAST-CHANGE SYSTEM •Fully welded, sturdy and robust steel construction •pressure up to 9 t/m² (-900 mbar rel.) •analogue vacuum pressure gauge •mechanical vacuum pressure regulator •transparent Silicone membrane up to 230°C, 780% elongation, Iaodoiquxgspfx Ag Uel 40 Shore-A •robust, heat resistant phenolic resin ply working surface with integrated air suction channels, thickness 16mm •extra vacuum connector (e.g. for external vacuum bag, vacuum clamping) •with intecrated forklift pockets •incl. swivel castors Heating drawer with CAS-heating system (Controlled Air Stream) •material thickness: 0 - 70 mm •heating power: max temperature +230°C •2 circulation hot air fans •pull-out working surface with grating, grid 30 x 30 mm •easy removable heating drawer Control unit with 4“ SIEMENS touch panel •hinged control cabinet on the right side •variable temperature control up to + 230 °C •temperature control with timer and alarm •complete with cable and plug Electrical connection3~ 400 V, 50/60 Hz, 17.5 kW Duoformer production capabilities: ● Pre-heating and forming of solid surface materials such as: CORIAN; HIMACS; KERROCK; HANEX; STARON; MISTRAL; AVONITE; TRISTONE; VELSTONE; WILSONART; GETACORE; RAUVISIO; VARICOR; PLEXICOR; MEGANITE; KRION; LIVINGSTONE; MARLAN; EOS; FORMICA; MYSTERA, etc. ● Pre-heating and forming of all other thermoformable materials such as: ABS, PMMA (Plexiglas, Perspex, Lucite), PET-G (Vivak), PE, PS, PP, PVC-U, PC (Makrolon), UPM-GRADA, RESYSTA, NFPP, etc. ● Vakuumpress for bonding, coating, edge banding, flat pressing, forming, gluing, laminated bending, pressing, spot on profile fitting, veneering Other dimensions on request! DUOFORMER Maxi Clamshell opening: work piece height approx. 650 mm Vertical opening: work piece height approx. 1000 mm Pressing surface LxW: 3380x1380mm Heating surface LxW: 3000x1250mm Heating drawer +230°C – 24kW Vacuum pumps 40m³/h, 80m³/h, 100m³/h Overall dimensions LxWxH: 3900x1600x1500mm DUOFORMER Mega For a whole length of solid surface material boards! Clamshell opening: work piece height approx. 650 mm Vertical opening: work piece height approx. 1000 mm Pressing surface LxW: 4150x1780mm Heating surface LxW: 3850x1250mm Heating drawer +230°C – 32kW Vacuum pumps 80m³/h, 100m³/h, 140m³/h Overall dimensions LxWxH: 4700x2050x1500mm UNIVERSALFORMERS Direct – Honest - Experienced

Year of construction: 2002, condition: good (used), For sale 4 Getecha sprue mills with screw conveyor Type: GRS 182 - A 2.29 year of construction 04/2002 Volt: 400 Amp.: 2.29 Iedpfx Ajhzqzrsg Uoal Granules sieve dm 5 mm Machines purchase / sale PURCHASE / SALE OF PRODUCTION & METALWORKING MACHINES ETC. Do you need a high quality but inexpensive metalworking machine for your production? Or do you want to sell yours? For more information or to contact us please visit our website

Condition: excellent (used), Volumetric K-Tron dosing with Ruhrwerk and auger - Suitable for powder and granulate Iasdpfsrvxn Iox Ag Uol - Screw diameter: 35 mm

Condition: used, The machine is suitable for the agglomeration of thermoplastic films and fibres. The throughput can be estimated to be 500 kg - 1000 kg/h, depending on the material, its condition and humidity. The system consists of: • conveyor belt • load-dependent control for the belt conveyor. • metal detector Iaodpfx Ajxgtqmog Uol • HERBOLD granulator type SMS 45/100-H5-3 • pneumatic material transport to the storage silo • plastcompactor unit HV-70 (consisting of a storage silo feeding screw, plastcompactor, central blower, cooling circuit) • HERBOLD secondary granulator type SML 45/100-S4-2 • intensive cooling • SZS II 630/200 conveying fan • screening machine, undersize grain will be returned into the compactor silo. • material conveyor type MFT with big bag station and automatic switchover to the on-site silo • automatic exhaust air filter • electrical control unit • compressor.

Condition: used, Condux Granulator type CS 300/600-4 WK Rotor diameter: 300 mm Rotor width: 600 mm Iaedpfx Ajxgtfwjg Ujl Rotor knives: 3 Housing with 4 stator knives Drive motor 11 kW (on request max. 30 kW)

Condition: used, Condux Granulator type CS 300/600-4 WK Rotor diameter: 300 mm Rotor width: 600 mm Isdpfx Ajxgrfieg Ujal Rotor knives: 3 Housing with 4 stator knives Drive motor 11 kW (on request max. 30 kW)

Condition: used, Refurbished granulator, heavy-duty series, hard-faced Can be used for dry and wet shredding Typical applications: Plastic hollow bodies, secondary shredding of pre-shredded waste, Iasdpoxgtgnsfx Ag Uel Rotor 800 mm diameter x 1600 mm width Open F7 rotor with replaceable blade supports Drive power 160-250 kw With forced feeding by 3 load-dependent controlled feed screws Hydraulically hinged, hydraulically swiveling screen basket Throughput capacity up to 5 t/h depending on material and grain size

Condition: used, HERBOLD granulator type SMS 60/100 Iedpfx Agjxgtm Uo Uoal Heavy version Inlet opening 700 x 1000 mm Open rotor 600 mm diameter x 980 mm width (optionally as open 3- or 7-blade rotor) Drive motor 110 kw Folding device with electric winch

Condition: used, Granulator / Granulators Manufacturer: HERBOLD Model: SMS 45/100-H5-3 Iasdpfxjxb Adle Ag Uel Semi-open 5x2 knife rotor, 2 stator knife rows. Machine is equipped with a replaceable third bed knife (deflector) for processing thick-walled materials. Inlet hopper suitable for conveyor belt feeding. Rotor mounted outside of the housing. Housing split in the middle, can be opened with a hand winch. Double inclined cut design: rotor and stator knives are positioned opposite each other and cut in a scissor-like manner. With base frame including vibration dampers. Machine data Rotor knives: 5 x 2 Stator knife rows: 2 Drive: 75 kW