Used Plastic Baler for sale (6,299)

Condition: good (used), Manufacturer: Comp Tip: SB5 Engine: 2,2 KW Ibsdpfsh Eic Ajx Aacoc Cylinder stroke length: 500 mm Chamber size: 500 x 350 x 400 mm

Condition: reconditioned (used), Year of construction: 2012, operating hours: 25,895 h, functionality: fully functional, pressing force: 78 t, filling opening width: 1,100 mm, filling opening length: 1,500 mm, bale width: 1,100 mm, bale height: 750 mm, bale weight: 600 kg, overall weight: 24,000 kg, oil tank capacity: 1,000 l, power: 55 kW (74.78 HP), volume flow: 930 m³/h, Technical data baler: Manufacturer Presona AB Typ LP 80 VHK 1 Year of construction 2012 Total machine operating hours 25,895 hours, as of July 2025 Pump operating hours, effective 14,135 hours, as of July 2025 Number of bales pressed 235,597 pieces, as of July 2025 Press power main press 78,5 tons Specific press capacity 95 N/cm² Press power of pre-press 28 tons Volume of pressing chamber 2,7 m³ Feed channel1,500 x 1,100 mm Theoretic throughput rate 930 m³/h Throughput rate under operating conditions 410 m³/h Bale size 750 x 1,100 mm Driving motor 55 kW Tying system 5 fold vertical, 3-fold horizontal, full automatic Throughput rate with a bulk density of 30 kg/m³ approx. 9 to 12 tonnes/hour, depending on material 50 kg/m³ approx. 14 to 17 tonnes/hour, depending on material 100 kg/m³ approx. 16 to 25 tonnes/hour, depending on material Throughput capacity with MSW (Municipal Solid Waste) approx. 20 to 27 tonnes/hour, depending on material Bale weight 450 up to 600 kg, depends on material and bale length Ibsdevwlqqepfx Aacsc Volume hydraulic oil tank 1,000 l Baler dimensions built up with hopper 10,985 x 3,750 x 4,310 mm (l x w x h) Transport dimensions only baler 10,985 x 2,300 x 2,900 mm (L x w x h) Machine weight baler approx. 24 tons Condition of the press: The machine was partially overhauled and serviced in our workshop and, once the work was complete, tested in manual and automatic mode during operation. The following overhaul work was carried out: Machine cleaned, partially derusted and partially repainted Hydraulic oil tank emptied and cleaned Oil filter and air filter replaced, new hydraulic oil filled Press ram dismantled and cleaned All four rollers removed from the press ram and replaced Wire station with deflection rollers for the lower wire cleaned and made operational Side guides removed from the press ram, smoothed, mounted and readjusted Main hydraulic cylinder dismantled and disassembled for inspection Piston rod replaced, cylinder tube honed Complete seal set replaced, pressure test carried out Vertical and horizontal needle system for binding dismantled, cleaned, wire deflection rollers made functional and serviced Chain cleaned, greased, chain tension readjusted Drillomat cleaned, wire knife, drill shafts and drill fingers checked, retightened with torque and serviced Door contact switch checked and partially replaced. Emergency stop switch checked. Complete electrical wiring checked and partially replaced. Bearings of the wire guide rollers under the press replaced. New safety grilles for vertical and horizontal binding manufactured and installed. Machine checked, general maintenance work carried out and press tested in manual and automatic mode Scope of delivery: Only the baler will be sold. Comments: The documentation (Manual, CE-declaration, electr./hydr.-drawings), are completely available. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors.

Condition: used, Year of construction: 1995, functionality: fully functional, input voltage: 400 V, power: 40 kW (54.38 HP), Baler from 1995. Viewing by appointment only. Isdjw H Ar Aepfx Aacjbc

Year of construction: 2016, condition: good (used), functionality: fully functional, HDPE extruder, head diameter 70 and 100 mm, screw diameter 50 mm, width up to 700 mm, 12-30 micron, single winding Isdpfx Aoxb A Uqeacobc

Condition: ready for operation (used), Technical specifications of Dixi 60 AUTOMAT baler Filling opening (W x H): 1550 x 1000 mm Ibedpov Amw Nefx Aacec Drive power: 31.5 kW Pressing force: 60 t Bale weight (depending on material): 350–600 kg Bale dimensions (W x H x D, adjustable): 1100 x 800 x 300–1600 mm Pressing/cycle time: 13/24 s Machine weight: 7000 kg

Condition: as good as new (ex-display), Year of construction: 2024, functionality: fully functional, overall weight: 270 kg, warranty duration: 24 months, empty load weight: 265 kg, Robust and compact construction High-quality components with a longer lifespan Above-standard productivity Iedpfx Aaju Tqmdjcebc Adjustable bale height (three sizes) Automatic start for efficient compaction Bale trolley for easy transport Material selector for cardboard and plastic Full bale indicator and service indicator Compliance with EN 16500:2014 safety standards

Condition: good (used), Manufacturer: MBT Ibedpfshzr U Iex Aacsc Tip: MV-250 S Motor: 5,5 kW hopper size: 780 x 600 mm Housing size: 3500 x 1000 x 2200 mm

Condition: excellent (used), Eos EOSINT plastic laser-sintering system Here we offer an Eos EOSINT plastic laser-sintering system. Ibodpfxjf Ey Eaj Aacjc Eos EOSINT Plastic Laser-Sintering-System P385 The EOS P385 system includes the following Installation space container Powder container Cooler: Termo TEK Termochiller 1100 The following upgrade has already been performed : Software: CD's Eosint P3 process software PSW 3.2 for Windows 2000, XP Materialice: Magics RP 9.0 Machine upgrade from P360 to P385 on 10.08.2007 Laser change 15.05.2008 X Drive Motor. Change of used engine 04.05.2020 Pyrometer change 30.06.2020 350mm x 350mm x 610mm Voltage 3/N/PE/ 400V A, frequency 50 Hz Connected load 8 kW Fuse 32 A MAX. Laser power 100 W Laser class open 4 Laser class Closed 1 Weight 850 kg Type: EOSINT Upgrade P385 condition: used / used Scope of delivery: (see picture) (Changes and errors in the technical data, specifications are reserved!) We can answer further questions for you on the phone.

Condition: excellent (used), Year of construction: 2024, functionality: fully functional, Baler Orwak Compactor 3150 Very good condition Iedpfx Aew Rn U Neacebc

Year of construction: 2012, condition: good (used), functionality: fully functional, machine/vehicle number: 1209107, T-shirt bags blocked, width 200-350 mm, length 280-700 mm, thickness 8-30 microns Iedpfx Aexb An Doacsbc

Condition: used, Year of construction: 1997, Van Dam 565 round cupprinter. year of build 1997 with 6 colours. Dupatech can deliver this machine including full remanufacturing, warranty, producing like a new one. Ibodon Sm Dzspfx Aacsc

Condition: excellent (used), Year of construction: 2018, functionality: fully functional, pressing force: 50 t, Fully functional Bramidan B50 baler, serviced, complete set - hook, strap rolls. Iedpfx Aaoxg Tk Tscjbc

Year of construction: 2018, condition: ready for operation (used), Installation: Indoors, material: PE100, internal dimensions X/Y: 1900mm/2200mm, internal drip tray dimensions X/Y: 2100mm/2000mm, useful volume: 6000l, liquid: HCl/Fe3Cl/H2O, density: 1.15kg/dm³, pressure: unpressurized. On-site inspection is possible. Ibjdpewqqwhefx Aacsc

Condition: excellent (used), Here we offer an Eos EOSINT plastic laser-sintering system. The following things are included in the EOS P380 system Construction space container Powder hopper Overflow container Cooler: Termo TEK Termochiller type: P411-12448-1 3DM 8 zones process chamber heating 250°C Each zone individually adjustable, homogeneous temperature field ± 1°C Kelvin 350mm x 350mm x 610mm Voltage 3/N/PE/ 400V AC Frequency 50 Hz Connected load 8 kW Fuse protection 32 A MAX. Laser power 100 W Laser class open 4 Laser class closed 1 Weight 850 kg Type: EOSINT P 380 Condition: used / used Scope of delivery: (see picture) (Changes and errors in the technical data, details are reserved!) Further questions we can answer on the phone for you. Ijdpsgqux Nsfx Aacsbc

Condition: reconditioned (used), Year of construction: 2004, functionality: fully functional, pressing force: 60 t, filling opening width: 1,150 mm, filling opening length: 735 mm, bale width: 1,200 mm, bale height: 1,200 mm, bale weight: 550 kg, total width: 2,000 mm, total height: 2,880 mm, total length: 1,900 mm, overall weight: 3,575 kg, transport height: 1,970 mm, power: 7.5 kW (10.20 HP), year of last overhaul: 2023, volume flow: 116 m³/h, transport width: 2,000 mm, transport length: 1,900 mm, How do you do? We hereby offer you, without obligation, a used, vertical baling press, from the manufacturer HSM, type VL 600, with 60t pressing force, year of manufacture 03/2004. The machine was used in a small logistics center for baling paper, cardboard and film and was only in operation for a few hours per week. The machine has been partially overhauled and tested. The machine documentation is available in German. A viewing of the press is possible by appointment. We would be pleased if this machine is of interest to you. Ibodpfx Asuaxv Tsacjc Your service team Mertens & Frowein GmbH

Year of construction: 2013, condition: good (used), functionality: fully functional, machine/vehicle number: 130669, loose bags, width 200-1100 mm, length 200-1500 mm, thickness 15-150 microns Ibjdoxb Ad Sepfx Aacjc

Condition: excellent (used), Year of construction: 2001, functionality: fully functional, OMSO Keycup 7 color round cupprinter. yob 2001, refurbished in 2020. in excellent running condition. Ijdpfxsuuh E Is Aacebc

Condition: reconditioned (used), Year of construction: 2005, operating hours: 30,408 h, functionality: fully functional, pressing force: 50 t, filling opening width: 1,100 mm, filling opening length: 1,250 mm, bale width: 1,100 mm, bale height: 720 mm, bale weight: 550 kg, overall weight: 16,000 kg, oil tank capacity: 600 l, year of last overhaul: 2024, Technical data baler: Manufacturer Presona AB Type LP 50 EH1 Year of construction 2005 Operating hours 30,408 hours, as of April Number of pressed bales 198,059 as of April Pressing force main press 50 tonnes Specific pressing force 63 N/cm² Theoretical throughput capacity 530 m³/hour Throughput capacity under operating conditions 260 m³/hour Dimensions of feed chute 1,250 x 1,100 mm Bale chamber volume 2.2 m³ Bale dimensions 1,100 x 720 mm, variable length Drive power 22 kW Tying 5-fold vertical, fully automatic Throughput rates with a bulk density of 30 kg/cbm 6 up to 7 tonnes/hour Bulk weight of 50 kg/cbm 7 up to 9 tonnes/hour Bulk weight of 100 kg/cbm 11 up to 14 tonnes/hour Bale density (paper/newspapers) 400 to 550 kg/m³ Hydraulic oil tank capacity 600 litres PLC control Telemecanique TSX Micro Schneider Magelis control panel Effective transport dimensions excl. baler 8,125 x 2,300 x 3,000 mm (L x W x H) Transport weight press approx. 16 tonnes Condition of the baler: The machine was partial overhauled in our workshop and general maintenance work was carried out. After completion of the overhaul work, the press was tested during operation and is available for sale at short notice. The following overhaul work was carried out: General work: Machine cleaned, derusted, primed, partially painted Wire entry marks in the press channel feed-throughs welded shut and smoothed Hydraulic unit: Hydraulic oil tank emptied, tank cleaned, new oil filled Oil filter and air filter replaced Leaky oil sight glass on hydraulic oil tank replaced All hydraulic hoses replaced Electrics: English language installed in the programme menu Two key switches in the control panel replaced Control cabinet replaced Signal lamp on the control cabinet replaced Flaps end switch replaced Electrical system of the turbulator replaced, connected and tested Press ram: All four rollers removed from the press ram and replaced Main hydraulic cylinder dismantled, disassembled and partially overhauled, cylinder tube honed, complete seal set replaced, leak test performed All plastic wear pads on the press ram replaced Pre-press: Both bearings on the pre-press shaft replaced. Both hydraulic cylinders dismantled, disassembled and partially overhauled, both cylinder tubes honed, complete seal sets replaced, leak test performed. Scraper flap on the pre-press replaced. Isdpfou Thhrex Aacsbc Binding system: Two complete needles with wire deflection rollers replaced Needles adjusted and set All wire deflection rollers in the needle heads replaced Drill fingers replaced Two drill shafts replaced All 8 wear plates on the Drillomat, under the drill fingers, replaced Scope of delivery: Only the baler will be sold. The documentation (Manual, CE-declaration, electr./hydr.-drawings), are completely available. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors.

Condition: excellent (used), Year of construction: 2017, Robopac Rotoplat 708 PDS Ibsdpfx Aaew R Ad Sscsc This is your opportunity to acquire a used Robopac Rotoplat 708 PDS, an advanced semi-automatic stretch wrapping machine from 2017 – ideal for businesses seeking efficient and reliable palletizing equipment. The machine offers: PVS film carriage with dual motors and adjustable film stretch between 150–400%, directly set from the control panel. Cube Technology™ for optimized film usage and load stability – save up to 55% film. Automatic height detection via photocell and patented S-threading for easy film loading. 7” color touchscreen with intuitive interface and Multilevel Control – allowing you to save and switch between 6 different load programs. R-Connect (may require new data connection) for remote monitoring, settings adjustment, and performance analysis. Manufacturer: Robopac Length: 2,750 mm Width: 1,650 mm Turntable diameter: 1,650 mm Height: 2,800 mm Max pallet height: 2,600 mm Max load: 2,000 kg Capacity: Up to 40 pallets/hour Available for immediate delivery. Shipping not included.

Year of construction: 2024, operating hours: 5 h, condition: as good as new (ex-display), 1 Hydropneumatic press type STHP 60 kN with two-hand operation - floor model with and without base frame Ibedpfxopn Unve Aacoc The compact and handy table model has a hydropneumatic drive with pressure intensifier which can increase the punching force up to 5 times. During the working stroke, the punching cylinder is pressurised with oil by the pressure intensifier and thus has a purely hydraulic punching stroke. The return stroke is performed directly with compressed air. The adapter that can be screwed into the piston rod of the working cylinder makes it possible to install special tool holders.

Year of construction: 2015, condition: used, Plastic crusher, power 55 kW, capacity 600 kg/h Ijdpoxdibvofx Aacobc

Year of construction: 2015, condition: new, We have a MATICA Espresso card printer available. This printer is bought by us in 2015 and has been standing in the showroom. Price new ist € 1.599,-, price now is € 999,- We have come to the conlcusion that this type of machinery is not the type of machinery we are able to offer as a distributor in a correct manner. Therefore this printer is new and has just printed max 10 cards in its life. Single or double side edge-to-edge Optional Magstripe and Smart Card encoder Ethernet and optional WiFi Prints up to 850 cards per hour 100-card feeder The Matica Espresso II is a compact and powerful desktop ID card printer, that is a brainchild of Italian design & engineering and reflects German reliability in consistent performance. The Espresso II offers great value and versatility with extraordinary printing speed and outstanding print quality. With its robust and durable construction, the Espresso II looks and works great in any office or card production environment. Ibjdpsfnldqefx Aacec The Espresso II is a single side desktop ID card printer for projects needing printing only on one side. The Espresso can be field-upgraded to easily double the printing capacity with the duplex printing feature. Any Espresso II printer can evolve to duplex anytime, anywhere without the need to install additional hardware components. Contact and contactless smart card encoding are also field-upgradable features. LED status indicators on the front of the printer allows you to monitor the card production process at a distance, and the blue LED light on the card hopper door keeps you aware of your card input availability in real time. You can also use optional single card manual insertion for individual card printing as needed. Each printer comes with a rear output hopper to catch full card runs as needed, which can improve the throughput speed in higher volume scenarios. In standard setup, having front-side input and output trays is also convenient for situations where space is limited, in a desktop environment, a cabinet or under a counter. Each Espresso II printer also has the option for inline magnetic stripe, contact chip or contactless smart card encoders, to maximize its functionality for a broader set of application uses, such as access control, time & attendance, payment services, and many more. The entire line offers Ethernet connectivity and optional WiFi making printing and encoding convenient and trouble-free. You can easily define your printer and choose the one that perfectly matches your current needs, as Espresso II offers a vast range of options. Whether or not your requirements evolve in the future, you have still the possibility of making an upgrade by adding functionalities to your existing configuration. The new printer line works perfectly for a wide variety of applications such as Employee and Membership ID Badges, Service and Benefits Cards, Gift and Loyalty Cards, Access Control Cards, Student IDs, and Transit Cards, just to name a few. The Espresso II is available with different specifications ​— modules, encoding, color, etc..

Condition: excellent (used), Year of construction: 2003, This Haul-off saw from our renowned brand SICA S.p.a. is in machine storage at Plastima Used Machinery. The saw is from 2003 and is in used but good condition. Brand: SICA S.p.A. Iedpfx Aajtphp Iscsbc Model: TRS/U 110-800 Year of construction: 2003 Power: 5.5 kW Pipe outer diameter max: 110 up to 800 mm

Condition: excellent (used), functionality: fully functional, Technical data for the document shredding system: Manufacturer HSM GmbH + Co KG General data for the two-stage shredder system: Type Duo Shredder 5750 Year of manufacture 2015 Operating hours 3,093 hours Throughput capacity up to 800 kg/hour, depending on material Rated power 30 kW Rated current 62 A Particle cutting size 6 x 40 - 53 mm Fuse protection 63 A gG/gL/C/K Weight of shredder approx. 2500 kg Data on the pre-shredder: Shredder type V 570 Working width of the cutting unit 500 mm Particle size 20 x 155 mm (w x l) Nominal power of pre-shredder 2 x 5.5 kW Nominal current of pre-shredder 2 x 11.5 A Data on the secondary shredder: Shredder type P 500.2 Working width of the cutting unit 500 mm Particle size 6 x 40 – 53 mm (w x l) Nominal power of secondary shredder 9.2 kW Nominal current of secondary shredder 18 A Security level according to DIN 66399 P-3, O-2, T-3, E-2 Baling press data: Type KP 100.1 Year of manufacture 2015 Operating hours 2,377 hours Pressing force 9 - 12 t Bale weight 40 – 150 kg/bale, depending on material Cycle time 7–16 seconds Feed chute dimensions 450 x 580 mm Bale size 630 x 500 x 400-1000 mm (w x h x l) Triple horizontal binding Press dimensions 3990 x 2225 x 1735 mm (l x w x h) Weight of press approx. 1000 kg Dimensions of entire system, conveyor belt, shredder and press: 9560 x 2071 x 3550 mm (l x w x h) Iedpjwrybrsfx Aacjbc Function description: This is a complete system consisting of a feed conveyor belt, a two-stage shredder and a horizontal baling pres. The material is fed onto the conveyor belt, shredded in two stages and then pressed into stackable bales. A second cutting unit and various motors are available as spare parts for the system. Comments: The documentation (Manual, electr./hydr.-drawings), are completely available. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors.

Condition: excellent (used), Year of construction: 2018, operating hours: 1,192 h, functionality: fully functional, rotor diameter: 260 mm, rotor width: 800 mm, power: 30 kW (40.79 HP), filling opening width: 800 mm, filling opening length: 1,450 mm, working width: 800 mm, Technical data wood and plastic shredder: Manufacturer WEIMA Maschinenbau GmbH Type WLK 800 Year of construction 2018 Operating hours 1,192 hours Drive power 30 kW Speed 90 rpm Rated current 70 A Slow-blow fuse 80 A Hydraulic pressure for horizontal slide 160 bar, load-dependent or pulsed control selectable Rotor type profiled V-rotor Rotor diameter 260 mm Rotor length 800 mm Rotor speed 80 - 125 rpm Number of cutting crowns, concave, 2-row, 42 pieces Cutting crown size 40 x 40 mm Grain size 15 - 80 mm Feed opening 800 x 1450 mm Ibedpfx Aowrxkljacjc Cutting chamber dimensions 720 x 700 mm Hopper capacity 0.8 m³ Machine dimensions 2,590 x 1,745 x 2,180 mm (l x w x h) PLC control Siemens SIMATIC S7-1200 Screen basket with 30 mm hole size, can be folded downwards Shredder transport weight 2.8 tonnes Machine equipment: Segmented floor 2-sided Free-cutting hopper Electromechanical drive with WEIMA WAP gearbox Hydromechanical starting clutch V-rotor (2-row) Adjustable counter blade for regulating the cutting gap Reversible counter blade Remote bearing for easy maintenance Condition of the shredder: The shredder was only used sporadically for wood and plastic shredding and is in good, ready-to-use condition. The machine is available at short notice. Scope of delivery: 1 Weimar WLK 800 shredder with control cabinet Comments: The documentation (Manual, electr./hydr.-drawings), are completely available. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors.