Used Plastic Baler for sale (6,763)

Condition: good (used), Year of construction: 2012, operating hours: 12,078 h, functionality: fully functional, pressing force: 88 t, filling opening width: 1,100 mm, filling opening length: 1,800 mm, bale width: 1,100 mm, bale height: 750 mm, bale weight: 750 kg, overall weight: 30,000 kg, oil tank capacity: 2,000 l, power: 98 kW (133.24 HP), volume flow: 643 m³/h, Technical data baler: Manufacturer HSM GmbH + Co. KG, Germany Type VK 8818 R-FU Year of construction 2012 Total operating hours: 12,078 hours, as of September 2025 Pump operating hours 6,616 hours (effective pump running time) Number of bales pressed: 65,792 bales, as of September 2025 Main press force 880 kN Specific pressing force 120 N/cm² Pressing force cutting edges free rammer 120 kN Dimensions of feed chute 970 x 1,800 mm Theoretical cycle time in idle mode 8.3 seconds Theoretical throughput capacity 643 m³/hour Bale dimensions 1,100 x 750 mm, the length is variable 600 up to 2000 mm Drive power 2 x 45 kW frequency-controlled Connected load 98 kW Total current consumption 192 A Fuse protection 250 A slow-blow 5-fold horizontal tying, fully automatic Throughput rates with a bulk density of 20 kg/cbm 12.86 t/hour Bulk weight of 50 kg/cbm 32.15 t/hour Bale weights with a bale length of approx. 1.2 m 650 up to 750 kg/bale, depends on materiel Hydraulic oil tank capacity 2000 litres PLC control Siemens S7-300 Siemens TP 700 control panel Press dimensions assembled 18,000 x 4,300 x 3.270 mm (l x w x h) Press dimensions with conveyor system 18,000 x 22,000 x 5,765 mm (l x w x h) Transport weight baler approx 30 t (Main press approx. 20 t, press channel with bale clamp approx. 10 t) Special machine equipment: Access locking by means of key transfer system Electro-hydraulic locking of the press carriage during the tying process so that the press plunger does not change position with highly expansive materials Additional optional equipment ordered: Frequency-controlled main drive, 2 x 45 kW, with up to 40 % energy savings compared to the standard motorisation 2 x 45 kW, with the same power output Manual switch-off or switch-on of the number of strapping wires to save on strapping wire for non-expansive material Cutting-edge frei rammer with 121 kN pressing force Sensory wire monitoring, with press switch-off in the event of wire breakage or wire end Bale chute Visual warning signal, mounted on the control cabinet Condition of the baler: The entire baling system (baler and conveyor belt) is in good, operational condition. Technical data for the chain belt conveyor: Manufacturer Stadler Anlagenbau GmbH Typ chain belt conveyor KF 1800 Year of construction 2012 Drive power 7.5 kW Belt speed 0.05 – 0.4 m/second Length of feeding conveyor 6,000 mm Height of side wall from feeding conveyor 400 mm Length of incline conveyor 9,000 mm Height of side wall from incline conveyor 800 mm Length of gooseneck 1,500 mm Incline 30° Nominal width 1,800 mm Useful width 1,700 mm Belt quality EP-500/4 Steel cleats on the rubber belt 50 x 50 mm Hollow pin chain, pitch 125 mm, rollers 36 mm Height of drive axle above ground 4,284 mm Ksdpfxoxcngne Ag Usdg Overall height of conveyor belt 5,765 mm Transport dimensions of feeding conveyor approx. 7,000 x 2,200 x 1,250 mm (l x w x h) Transport dimensions of the incline conveyor 13,000 x 2,500 x 2,900 mm (l x w x h) Pit dimensions for the conveyor belt 14,765 x 3,260 x 1,250 (l x w x h) Scope of delivery: The conveyor belt, baling press with bale chute, and wire drawing stations are available for sale, but without the wire. Comments: The documentation (Manual, CE-declaration, electr./hydr.-drawings), are completely available. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors.

Condition: used, functionality: unexamined, color: white, Plastic cleanroom transport boxes Kdsdsxn Ninepfx Ag Ujg Lockable from top and bottom External dimensions: 78 x 117 x 104 cm Internal dimensions: 65 x 103 x 90 cm

Condition: good (used), functionality: fully functional, A Thermobend 2000 is a bending machine used for bending plastic sheets such as PMMA (acrylic glass) and methacrylate. The machine operates with heating wires to heat and bend the sheets at specific locations. Key features Capacity: The machine has a usable length of 2000 mm. Functionality: Can bend sheets with a thickness of 1 mm to 20 mm. Configuration: Equipped with 2 bending beams heated both from above and below. The distance between the wires is adjustable, with 3 wires above and 3 below per group. Dimensions: Length: 3200 mm x Width: 1000 mm x Height: 1600 mm Kjdpfx Aoxn T Nrog Uodg Please note: The information on this page has been obtained and compiled to the best of our knowledge, but accuracy cannot be guaranteed. Accordingly, it does not constitute a representation or contract, and we recommend verifying all relevant details. Financial information VAT/margin: Margin: The listed price includes VAT (VAT is non-deductible for businesses).

Condition: ready for operation (used), Year of construction: 2021, This EVO-tech EL-102 V2 was manufactured in 2021. A plastic 3D printer featuring a robust 400 VAC system, it operates efficiently within a temperature range of 5–35 °C and humidity levels of 20–85% RH. It adheres to safety with IP41 protection and CE marking. Consider the opportunity to buy this EVO-tech EL-102 V2 plastic 3D printer. Contact us for more information. Application Types 3D Printing Kdodpfx Agsx D Sics Ueg

Condition: excellent (used), Year of construction: 2004, operating hours: 34,480 h, functionality: fully functional, pressing force: 100 t, filling opening width: 1,100 mm, filling opening length: 1,600 mm, bale width: 1,100 mm, bale height: 720 mm, bale weight: 750 kg, overall weight: 19,000 kg, transport height: 3,300 mm, oil tank capacity: 750 l, power: 45 kW (61.18 HP), Technical data baler: Manufacturer Bollegraaf Typ HBK 100 Year of construction 2004 Hours of operation 34,480 hours Press power main press 100 tons Press power of pre-press max. 42 tons Kdedpfsxbgnhox Ag Uog Feed channel 1,600 x 1,100 mm Filling volume 3.15 m³ Theoretic cycle time 22 sec. Theoretic throughput capacity up to 450 m³/hour Bale size 1,100 x 720 mm, lenght variable Driving motor 45 kW Connected load 60 kW Tying system 5-fold vertical, fully automatic Throughput rate at a bulk weight of 30 kg/cbm approx. 13 tons/hour bulk weight of 50 kg/cbm approx. 20 tons/hour bulk weight of 100 kg/cbm approx. 30 tons/hour Throughput rate with ruffler approx. 20 tons/hour Bale weight 550 up to 750 kg, depends on material Volume hydraulic oil tank 750 l SPS controller Telemecanique TSX Micro Transport dimensions only baler 10,900 x 2,320 x 3,300 mm (l x w x h) Machine weight baler approx. 19 tons Comments: Unlike the standard HBC press series from Bollegraaf, this machine does not have a pre-press flap but cuts the material between blades on the press ram and the counter blade in the frame. This makes it a cutting edge press, similar to a Paal, unoTech, etc. The press is in very good condition for its age, as it was used exclusively for compressing paper from document destruction. The documentation (Manual, CE, electr./hydr.-drawings), are completely available. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors.

Condition: good (used), Year of construction: 2024, Medium-sized baler, BMO, 150 Auto – used – : Price ex location: now only €3,950 instead of €4,900 (net) Manufacturer: Orwak Model: Compactor 3150 Type: 150 Auto HT RAL 3150 Serial number: 167317 Year of manufacture: 2024 Serial number: 167317 Dimensions of raw material bale: Height: 800 mm Width: 1,000 mm Depth: 1,000 mm Weight: up to 150 kg (depending on material) Cycle time: 40 seconds Feed opening dimensions: Height: 460 mm Width: 1,003 mm Depth: 800 mm Baler dimensions: Height: 2,546 mm Width: 1,366 mm Depth: 1,000 mm Own weight: 720 kg Transport height: 1,976 mm Power supply: 220 – 240 V Motor: 1.1 kW / 10 Amp. Pressing force: up to 7.6 t Operating noise: 62 dB • Easy and uncomplicated loading, even with larger cartons • Ideal for medium material quantities up to 3.3 t / month • Integrated retaining claws to reduce material spring-back • Fully automatic bale ejection – effortless removal of the bale from the press Former new price: €10,802.00 (net) Condition: good Available: immediately Location: 68307 Mannheim Kdsdpjw D Rvqofx Ag Uog

Condition: used, functionality: unexamined, Used mobile plastic storage box. Three layers and a lid. With brake. Adjustable handle/bar for storage and transport. Dimensions: 123/93cm x 85cm x 114cm (LxWxH). Price per unit. Kdodpfjxmhacex Ag Ueg

Condition: excellent (used), Year of construction: 2003, This Haul-off saw from our renowned brand SICA S.p.a. is in machine storage at Plastima Used Machinery. The saw is from 2003 and is in used but good condition. Kdjdpfx Aetphp Ijg Usg Brand: SICA S.p.A. Model: TRS/U 110-800 Year of construction: 2003 Power: 5.5 kW Pipe outer diameter max: 110 up to 800 mm

Condition: refurbished (used), Year of construction: 1999, functionality: fully functional, pressing force: 71 t, filling opening width: 1,080 mm, filling opening length: 1,620 mm, bale width: 1,100 mm, bale height: 720 mm, bale weight: 600 kg, total width: 3,450 mm, total height: 4,090 mm, total length: 10,020 mm, input voltage: 400 V, overall weight: 27,000 kg, noise level: 85 dB, pressure: 300 bar, transport height: 2,300 mm, power: 37 kW (50.31 HP), Fully automatic channel baler with pre-press flap available immediately. The machine includes a conveyor belt with a floor-mounted section. The baler is supplied in refurbished condition and the conveyor belt underwent a belt overhaul at the beginning of this year. The machine was taken out of production at the beginning of October and is currently stored in our facility. It can be demonstrated in operation at our location. This machine is particularly suitable for baling paper/cardboard and various types of plastics such as PET, HDPE, and big bags. Technical specifications baler: Drive: 37 kW Press force: 71 tons Bale dimensions: 1100 x 720 x 1300 mm (length adjustable) Number of wires: 4 vertical Kedpfxexl Rqbe Ag Ujdg Filling hopper dimensions: 1620 x 1080 mm Bale weight: up to 600 kg (depending on material) Capacity: up to 20 tons per hour (depending on material) Transport weight: 27,000 kg Technical specifications conveyor belt: Length of horizontal section: 3,000 mm Length of inclined section: 7,424 mm Angle: 29° Filling option: at floor level

Condition: excellent (used), Year of construction: 2016, operating hours: 6,500 h, A scrap shear in very good condition is for sale. The machine can be inspected at any time. Kdedpfx Agjxnavxe Usg

Year of construction: 2012, condition: good (used), Colortronic Dry-Flex M400 Granule Dryer For sale is a used Dry-Flex M400 granule dryer from Colortronic. Technical details (according to the nameplate): Manufacturer: Colortronic, Friedrichsdorf (Germany) Model: Dry-Flex M400 Year of manufacture: 11/2012 Control panel: 6AV6642-0BA01-1AX1 Operating voltage: 400 V / 50 Hz Heating power: 33 kW Drive power: 5.5 kW Kodpfx Ajxlqzteg Ujdg Operating pressure: max. 6 bar Design: Granule dryer / plastic dryer Area of ​​application: Plastics processing, injection molding, extrusion Condition: Used, functional Buy Colortronic Dry-Flex M400 granule dryers and other items at a great price – Here you can buy products from professionals for professionals – You'll find other attractive offers in our SHOP.

Condition: reconditioned (used), Year of construction: 2012, operating hours: 25,895 h, functionality: fully functional, pressing force: 78 t, filling opening width: 1,100 mm, filling opening length: 1,500 mm, bale width: 1,100 mm, bale height: 750 mm, bale weight: 600 kg, overall weight: 24,000 kg, oil tank capacity: 1,000 l, power: 55 kW (74.78 HP), volume flow: 930 m³/h, Technical data baler: Manufacturer Presona AB Typ LP 80 VHK 1 Year of construction 2012 Total machine operating hours 25,895 hours, as of July 2025 Pump operating hours, effective 14,135 hours, as of July 2025 Number of bales pressed 235,597 pieces, as of July 2025 Press power main press 78,5 tons Specific press capacity 95 N/cm² Press power of pre-press 28 tons Volume of pressing chamber 2,7 m³ Feed channel1,500 x 1,100 mm Theoretic throughput rate 930 m³/h Throughput rate under operating conditions 410 m³/h Bale size 750 x 1,100 mm Driving motor 55 kW Tying system 5 fold vertical, 3-fold horizontal, full automatic Throughput rate with a bulk density of 30 kg/m³ approx. 9 to 12 tonnes/hour, depending on material 50 kg/m³ approx. 14 to 17 tonnes/hour, depending on material 100 kg/m³ approx. 16 to 25 tonnes/hour, depending on material Throughput capacity with MSW (Municipal Solid Waste) approx. 20 to 27 tonnes/hour, depending on material Bale weight 450 up to 600 kg, depends on material and bale length Volume hydraulic oil tank 1,000 l Baler dimensions built up with hopper 10,985 x 3,750 x 4,310 mm (l x w x h) Transport dimensions only baler 10,985 x 2,300 x 2,900 mm (L x w x h) Machine weight baler approx. 24 tons Condition of the press: The machine was partially overhauled and serviced in our workshop and, once the work was complete, tested in manual and automatic mode during operation. The following overhaul work was carried out: Machine cleaned, partially derusted and partially repainted Hydraulic oil tank emptied and cleaned Kodpfjvwlqqsx Ag Usdg Oil filter and air filter replaced, new hydraulic oil filled Press ram dismantled and cleaned All four rollers removed from the press ram and replaced Wire station with deflection rollers for the lower wire cleaned and made operational Side guides removed from the press ram, smoothed, mounted and readjusted Main hydraulic cylinder dismantled and disassembled for inspection Piston rod replaced, cylinder tube honed Complete seal set replaced, pressure test carried out Vertical and horizontal needle system for binding dismantled, cleaned, wire deflection rollers made functional and serviced Chain cleaned, greased, chain tension readjusted Drillomat cleaned, wire knife, drill shafts and drill fingers checked, retightened with torque and serviced Door contact switch checked and partially replaced. Emergency stop switch checked. Complete electrical wiring checked and partially replaced. Bearings of the wire guide rollers under the press replaced. New safety grilles for vertical and horizontal binding manufactured and installed. Machine checked, general maintenance work carried out and press tested in manual and automatic mode Scope of delivery: Only the baler will be sold. Comments: The documentation (Manual, CE-declaration, electr./hydr.-drawings), are completely available. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors.

Condition: reconditioned (used), Year of construction: 2005, operating hours: 30,408 h, functionality: fully functional, pressing force: 50 t, filling opening width: 1,100 mm, filling opening length: 1,250 mm, bale width: 1,100 mm, bale height: 720 mm, bale weight: 550 kg, overall weight: 16,000 kg, oil tank capacity: 600 l, year of last overhaul: 2024, Technical data baler: Manufacturer Presona AB Type LP 50 EH1 Year of construction 2005 Operating hours 30,408 hours, as of April Number of pressed bales 198,059 as of April Pressing force main press 50 tonnes Specific pressing force 63 N/cm² Theoretical throughput capacity 530 m³/hour Throughput capacity under operating conditions 260 m³/hour Dimensions of feed chute 1,250 x 1,100 mm Bale chamber volume 2.2 m³ Bale dimensions 1,100 x 720 mm, variable length Drive power 22 kW Tying 5-fold vertical, fully automatic Throughput rates with a bulk density of 30 kg/cbm 6 up to 7 tonnes/hour Bulk weight of 50 kg/cbm 7 up to 9 tonnes/hour Bulk weight of 100 kg/cbm 11 up to 14 tonnes/hour Bale density (paper/newspapers) 400 to 550 kg/m³ Hydraulic oil tank capacity 600 litres PLC control Telemecanique TSX Micro Schneider Magelis control panel Effective transport dimensions excl. baler 8,125 x 2,300 x 3,000 mm (L x W x H) Transport weight press approx. 16 tonnes Condition of the baler: The machine was partial overhauled in our workshop and general maintenance work was carried out. After completion of the overhaul work, the press was tested during operation and is available for sale at short notice. The following overhaul work was carried out: General work: Machine cleaned, derusted, primed, partially painted Kdsdpfx Ageu Thhro Uog Wire entry marks in the press channel feed-throughs welded shut and smoothed Hydraulic unit: Hydraulic oil tank emptied, tank cleaned, new oil filled Oil filter and air filter replaced Leaky oil sight glass on hydraulic oil tank replaced All hydraulic hoses replaced Electrics: English language installed in the programme menu Two key switches in the control panel replaced Control cabinet replaced Signal lamp on the control cabinet replaced Flaps end switch replaced Electrical system of the turbulator replaced, connected and tested Press ram: All four rollers removed from the press ram and replaced Main hydraulic cylinder dismantled, disassembled and partially overhauled, cylinder tube honed, complete seal set replaced, leak test performed All plastic wear pads on the press ram replaced Pre-press: Both bearings on the pre-press shaft replaced. Both hydraulic cylinders dismantled, disassembled and partially overhauled, both cylinder tubes honed, complete seal sets replaced, leak test performed. Scraper flap on the pre-press replaced. Binding system: Two complete needles with wire deflection rollers replaced Needles adjusted and set All wire deflection rollers in the needle heads replaced Drill fingers replaced Two drill shafts replaced All 8 wear plates on the Drillomat, under the drill fingers, replaced Scope of delivery: Only the baler will be sold. The documentation (Manual, CE-declaration, electr./hydr.-drawings), are completely available. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors.

Condition: excellent (used), Year of construction: 2018, operating hours: 1,192 h, functionality: fully functional, rotor diameter: 260 mm, rotor width: 800 mm, power: 30 kW (40.79 HP), filling opening width: 800 mm, filling opening length: 1,450 mm, working width: 800 mm, Technical data wood and plastic shredder: Manufacturer WEIMA Maschinenbau GmbH Type WLK 800 Year of construction 2018 Operating hours 1,192 hours Drive power 30 kW Speed 90 rpm Rated current 70 A Slow-blow fuse 80 A Hydraulic pressure for horizontal slide 160 bar, load-dependent or pulsed control selectable Rotor type profiled V-rotor Rotor diameter 260 mm Rotor length 800 mm Rotor speed 80 - 125 rpm Number of cutting crowns, concave, 2-row, 42 pieces Cutting crown size 40 x 40 mm Grain size 15 - 80 mm Feed opening 800 x 1450 mm Cutting chamber dimensions 720 x 700 mm Hopper capacity 0.8 m³ Machine dimensions 2,590 x 1,745 x 2,180 mm (l x w x h) PLC control Siemens SIMATIC S7-1200 Screen basket with 30 mm hole size, can be folded downwards Shredder transport weight 2.8 tonnes Machine equipment: Segmented floor 2-sided Free-cutting hopper Electromechanical drive with WEIMA WAP gearbox Hydromechanical starting clutch V-rotor (2-row) Adjustable counter blade for regulating the cutting gap Reversible counter blade Remote bearing for easy maintenance Condition of the shredder: The shredder was only used sporadically for wood and plastic shredding and is in good, ready-to-use condition. The machine is available at short notice. Kjdpfx Aswrxkljg Usdg Scope of delivery: 1 Weimar WLK 800 shredder with control cabinet Comments: The documentation (Manual, electr./hydr.-drawings), are completely available. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors.

Condition: excellent (used), functionality: fully functional, Technical data for the document shredding system: Manufacturer HSM GmbH + Co KG General data for the two-stage shredder system: Type Duo Shredder 5750 Year of manufacture 2015 Operating hours 3,093 hours Throughput capacity up to 800 kg/hour, depending on material Rated power 30 kW Rated current 62 A Particle cutting size 6 x 40 - 53 mm Fuse protection 63 A gG/gL/C/K Weight of shredder approx. 2500 kg Data on the pre-shredder: Shredder type V 570 Kodpfx Aewrybreg Ujdg Working width of the cutting unit 500 mm Particle size 20 x 155 mm (w x l) Nominal power of pre-shredder 2 x 5.5 kW Nominal current of pre-shredder 2 x 11.5 A Data on the secondary shredder: Shredder type P 500.2 Working width of the cutting unit 500 mm Particle size 6 x 40 – 53 mm (w x l) Nominal power of secondary shredder 9.2 kW Nominal current of secondary shredder 18 A Security level according to DIN 66399 P-3, O-2, T-3, E-2 Baling press data: Type KP 100.1 Year of manufacture 2015 Operating hours 2,377 hours Pressing force 9 - 12 t Bale weight 40 – 150 kg/bale, depending on material Cycle time 7–16 seconds Feed chute dimensions 450 x 580 mm Bale size 630 x 500 x 400-1000 mm (w x h x l) Triple horizontal binding Press dimensions 3990 x 2225 x 1735 mm (l x w x h) Weight of press approx. 1000 kg Dimensions of entire system, conveyor belt, shredder and press: 9560 x 2071 x 3550 mm (l x w x h) Function description: This is a complete system consisting of a feed conveyor belt, a two-stage shredder and a horizontal baling pres. The material is fed onto the conveyor belt, shredded in two stages and then pressed into stackable bales. A second cutting unit and various motors are available as spare parts for the system. Comments: The documentation (Manual, electr./hydr.-drawings), are completely available. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors.

Condition: good (used), Year of construction: 2007, Baler STRAUTMANN PP1208, year of manufacture 2007 Kdjdpexwc Nyefx Ag Ujg

Condition: good (used), Year of construction: 2015, Year of manufacture 2015, serial number 413.00.032, pressing force 600 kN Ksdpexwc Naofx Ag Ujdg

Condition: used, Year of construction: 2017, Mono rotor shredder 800 series 2017 used, working blades and sieve in good condition, ready for use. including switch box. 30 kW, 40 mm sieve, other sizes in consultation, Kdsdpswcp H Sjfx Ag Ueg rotor length 800 mm, hopper dimensions 800 x 1200 x 950 mm Depth machine is immediately available and can be inspected.

Condition: new, Year of construction: 2025, Plastic processing plant(s) In any size and for any capacity. Ksdevi I Dwjpfx Ag Uodg Plastic, Wood, Rubber, Customized/ designed to your available space. are you looking for a partner to design, manufacture, install and also assist in the operation of your plant. call or email us, don't forget to mention your name, Firmaname and phone number, we will definitely call you.

Condition: excellent (used), Year of construction: 1996, pressing force: 30 t, input voltage: 380 V, bale weight: 600 kg, type of input current: AC, overall weight: 3,000 kg, Manufacture: Philadelphia Tramrail Model: HT30036 Vintage: 1996 400V/45A, 3 phases, 15kW 180 bar system pressure 206 bar maximum system pressure Made of heavy-duty structural steel Kdsdpfxom Amk Nj Ag Ueg Average cycle time of 53 seconds Dimensions: 1980 x 1050 x 3860mm Advance height: 1400mm Baling chamber: 1600 x 760

Condition: excellent (used), Year of construction: 1997, power: 1.5 kW (2.04 HP), Tria plastic grinder, shredder, granulator for sale in excellent condition Kdodjra N A Nopfx Ag Ujg make: TRIA 20-15/BL-T Power: 1.5kW, 50Hz, 380V Year of manufacture: 1997 Inlet opening: 200 x 230mm rotating knives 3 pcs standing knife: 1 pc Spout opening: 60mm Final product size: 3-5mm Capacity: 30 kg/h approx.

Condition: used, Year of construction: 1995, functionality: limited functionality, cutting force: 800 t, empty load weight: 190,000 kg, type of input current: three-phase, Arnold HS850 Scrap & Metal Presse Die Maschine befindet sich derzeit in transportbereitem Zustand. master cylinder cylinder force: 850 t press: 0.08m/s hold-down cylinder cylinder force: 100t / per cylinder feed cylinder: cylinder force:100t cover cylinder: cylinder force:100t main dimensions total length:16175mm total width:5200 total height: 6420 mm Dimensions: Passage width at the scissor stand: 800mm passage height at the scissor stand: 800mm total height: 6000mm Kjdjh T Dctjpfx Ag Ujdg weights: scissor stand with cutter bar: 60 ton feed device approx: 85 ton total weight: about 170 tons required amount of oil: 5200 liters connection value of the machine: 220kw If you need more information. We are here to help! Please contact us using the contact form or give us a call Your ad has been automatically translated. Translation errors are possible.

Condition: used, Year of construction: 2005, functionality: fully functional, machine/vehicle number: MST-0800C0028, For sale: automatic plastic injection molding machine ATEC HQ-800QL. Year of manufacture – 2005 (04), Serial No. MST-0800C0028. Hydraulic system with digital control panel, suitable for serial production of plastic parts. Power supply 380 V, 50 Hz, 3 phases. Used, fully equipped, previously operated in production. Suitable for manufacturing technical, packaging, and industrial plastic components. Inspection on site possible. Kodpfx Agsx Nhy Re Uedg

Condition: used, High-performance baler MACFAB - BEMA type 650A Hydraulic press for packaging waste, recyclable renewable raw materials, secondary raw materials Manufacturer no. MF J0162 Year of manufacture 2021 Pressing force 50 tons. Press plate stroke approx. 1000 mm Cycle time per stroke approx. 40 sec. Pressing chamber floor area 1500 x 1100 mm Pressing chamber height 1650 mm Filling opening 1500 x 870 mm Filling height approx. 1250 mm Bale format 1500 x 1100 mm Bale height max. 1100 mm Hydraulic operating pressure 200 bar Kdsdpfx Aevq Rtkog Ueg Motor power 5.5 kW Mains connection 400 volts, 50 Hz, 12 amps. - with two hydraulic cylinders - Door locking via threaded spindle with handwheel - Pressing operation only with the pressing chamber door closed - 2-hand operation for hydraulic tipping of the finished pressed bale - Free space for manual strapping - Standard industrial bales of 1500 x 1100 x 1100 mm are produced - the highly compressed bale is automatically tipped onto a pallet - only 62 operating hours Space requirement L x W x H 2120 x 1350 x 3220 mm Height for transport with lowered hydraulic cylinders approx. 260 cm Weight 1.8 ton. The machine is in very good condition, as good as new. The press has a new price of EUR 22,200 net at BEMA The BEMA company also buys the packaging waste that you press into bales with this press.

Condition: used, Year of construction: 2006, Bale size 400x400 mm Force 1 Step 850 KN Force 2 Step 850 KN Force 3 Step 850 KN Steel < 8 to/h Aluminium < 4 kg/h Driving Power 50 KW Arrangement Surface 7,5 x 7,2 m x m Machine weight 29 to Press box aperture1,9 x 0,95 mxm Kdsdjltinwspfx Ag Uog Place: Germany Available immediately