Used Holzkraft Hbs 351 Test for sale (165)

Condition: as good as new (ex-display), Year of construction: 2025, For wood chips and wood dust. Designed for commercial use. All clean air extraction systems in this series are dust-tested according to H3, with a residual dust content of less than 0.1 mg/m³. High extraction performance with a small footprint. Maximum performance in this class. Very quiet. Application area: Clean air extraction systems for wood chips and wood dust. Designed for commercial use. For all woodworking machines with a corresponding extraction port diameter. Can also be used for multiple dust sources. High-quality, well-designed construction. Robust and compact housing made of galvanized sheet steel. Extraction port can be easily repositioned from left to right, allowing for flexible use. Large inspection openings. Large, mobile chip containers with clamping bracket and chip collection bag. The system is fully assembled upon delivery, allowing for quick deployment. Mobile. Filter description: Ultra-compact with maximum filter area. Filter material made of polyester fleece, aluminum-coated, washable, and therefore with a long service life. Filter is standard and tested and approved in antistatic design according to category M-BIA. Filter resistance monitoring via differential pressure sensor, adjustable with a warning light on the control panel. The fan is located downstream of the filter. Equipment details: With a new locking device for secure container positioning. All systems in this series are dust-tested according to H3, with a residual dust content of less than 0.1 mg/m³. Scope of supply: Metal fan impeller. Inspection opening for cleaning the bypass filter. Connection cable 5 m with CEE plug 5-pole and phase inverter. 2 swivel castors and 2 fixed castors with parking brake. Preparation for connection of machine detection for up to 8 machines and slide valve controls. Manual cleaning. Sound pressure attenuator available as an accessory. Model: RLA 125 M Article no.: 5131256 Technical data Extraction port diameter: 125 mm Motor power: 2.2 kW Mains voltage: 400 V Mains frequency: 50 Hz Nominal volume flow: 1095 m³/h Max. volume flow: Vacuum at Vnenn: Dcjdpfx Aqecnw U Dsvsp Filter area: 5.31 m² Filter material: Dust class M Residual dust content: 0.1 mg/m³ Chip collection volume: 1 x 239 l Max. sound pressure level: 73 dB(A) Dimensions (L x W x H): 1100 x 830 x 1650 mm Height from the lower edge of the extraction port to the ground: 850 mm Weight: 194 kg Location: Arriving at warehouse 54634 Bitburg.

Condition: new, Year of construction: 2025, 4-knife cutterhead for optimal planing results Smooth operation thanks to the precision unit and the heavy cast-iron construction Front steel infeed roller with helical gearing for optimal feed rate Satin-finished steel outfeed roller, optionally with a rubber roller in the outfeed The work table is mounted on four large columns, ensuring maximum stability under all working conditions. The thickness table adjustment is done via a handwheel with a numerical display for the set planing height (accurate to 1/10 mm) Standard with two feed speeds, comfortably selectable from the operator's side Powerful industrial motor Stable steel and cast iron construction Equipment details: Work table Mounted on four large spindles, which ensure maximum stability under all working conditions A special lifting device ensures that the table position is maintained perfectly, even without locking TERSA planing cutterhead No more adjustment and screwing Planer knife change in seconds Self-locking Particularly quiet Thickness table adjustment on S 41 elite s via a handwheel with a numerical display for the set planing height (accurate to 1/10 mm) Dimensions and weights Length approx. 900 mm Width/Depth approx. 1070 mm Weight approx. 361 kg Dust extraction connection Dust extraction nozzle diameter for thicknessing 120 mm Drive power Main motor 5 kW Installation information Space requirement Length 1070 mm Space requirement Width/Depth 900 mm Space requirement Height 1100 mm Explanation of space requirement: The dimensions take into account maximum travel distances or usable lengths. Machine body Length 1040 mm Machine body Width/Depth 900 mm Length 3000 mm Width 1600 mm Explanation of working area: Please add the specified dimensions to the space requirement to obtain the recommended free installation area for the machine. Thicknessing Thickness table Length 423 mm Thickness table Width 775 mm Working height min. 3 mm Working height max. 240 mm Dedpfx Aqsd Hx Hnevscp Working length min. 180 mm Maximum chip removal 5 mm Electrical data Connection voltage 400 V Planer cutterhead Type TERSA Diameter 95 mm Number of planer knives 4 pcs Speed 5000 min¯¹ Planer width max. 410 mm Feed Speed 6/12 m/min

Condition: new, Year of construction: 2026, Holzkraft Minimax ST 5es – Maximum configuration for professionals Saw-milling combination with miter cutting device and pivoting milling spindle Art. No.: 5501086 Ø 350 mm main saw blade with 118 mm max. cutting height, which is also achieved when the scoring saw blade is installed Scoring device with separate motor and Ø 120 mm saw blade, easily and precisely adjustable from the outside Saw unit can be pivoted from 90° to -45° High-precision format sliding table made of anodized aluminum Large extension table (1200 x 650 mm) With material roller and extendable aluminum telescope stop up to 3300 mm Pivoting milling spindle from 90° to -45° towards the rear into the milling fence Four milling speeds With right/left rotation of the milling spindle Three independent motors With lockable main switch, motor protection switch Supplied as standard with separate saw parallel fence and separate jointing fence for planing Equipment details: Sliding table with ball contact system Made of anodized aluminum Guides made of hardened and ground steel, 15% harder than conventional steel Double-bearing milling unit Djded Hx Hmspfx Aqvjcp Pivoting, made of cast iron Mounting points directly on the table, resulting in optimal smoothness Milling spindle mounted high up on precision ball bearings, resulting in low bearing load and maximum possible service life Powerful industrial motors Milling fence Heavy-duty professional design The high-quality milling fence made of cast iron is supplied as standard with fine adjustment 3-way positionable for quick resetting of the setting With fine adjustment via rack and pinion, numerical display and aluminum milling fence jaws Parallel fence With fine adjustment and quick clamping Stable round bar guide made of ground steel Can be conveniently folded down for cutting large workpieces Interchangeable aluminum ruler for narrow workpieces Cast iron double-bearing saw unit Height adjustment via dovetail guide Extremely robust and torsion-resistant for precise cuts Close to the saw blade, bearing on both sides Height and adjustable up to 45° Scoring unit with separate scoring motor 0.55 kW as standard Extension table with angle-adjustable telescope stop with degree grid division Dimensions and weights Weight approx. 900 kg Dust extraction connection Dust extraction nozzle diameter 3 x 120 mm Dust extraction nozzle diameter saw blade guard 80 mm Drive power Scoring motor 0.55 kW Main motor 2 x 5.0 kW Electrical data Connection voltage 400 V Format sliding table and table Format sliding table width 360 mm Format sliding table height 142 mm Table length 1380 mm Table width 465 mm Milling spindle Spindle inclination 0 – -45 ° Usable length of the spindle 125 mm Spindle speeds 3500/6000/8000/10000 min⁻¹ Milling tool diameter max. Lowerable 240 mm Mortise milling 320 mm Circular saw unit and scoring saw Cutting length 3200 mm Cutting width with parallel fence 900 mm Max. ripping width to the left of the saw blade 3300 mm Saw blade inclination 90 - 45 ° Max. cutting height 90° 104 mm Max. cutting height 45° 68 mm Location: In stock, 54634 Bitburg - available immediately -

Condition: new, Year of construction: 2025, 4-knife cutterhead for optimal planing results Smooth operation thanks to precision drive unit and heavy cast iron construction Front steel infeed roller with helical teeth for optimal feed rate Satin-finished steel outfeed roller, optionally with rubber roller on the outfeed side The worktable is mounted on four large columns, ensuring maximum stability under all operating conditions. Thickness table adjustment is carried out via a handwheel with a numerical display for the set planing height (accurate to 1/10 mm) Standard equipment includes two feed speeds, conveniently selectable from the operator's front Powerful industrial motor Stable steel/cast iron construction Equipment details: Worktable Mounted on four large spindles, ensuring maximum stability under all operating conditions A special lifting device ensures that the table position is maintained perfectly, even without locking TERSA planing cutterhead No more adjustment and screwing required Planer knife changes in seconds Self-locking Motorized thickness table height adjustment in S 52 elite s Motorized height adjustment of the thickness table with electronic decimal display For greater precision and user-friendliness Dimensions and weights Length approx. 1080 mm Width/Depth approx. 1440 mm Weight approx. 455 kg Dust extraction connection Dust extraction nozzle diameter (thicknessing) 120 mm Drive power Main motor 7 kW Installation information Space required (length) 1440 mm Space required (width/depth) 1071 mm Space required (height) 1088 mm Explanation of space required: The dimensions take into account maximum travel distances or usable lengths. Machine body length 1030 mm Machine body width/depth 998 mm Length 1000 mm Width 1800 mm Explanation of work area: Please add the specified dimensions to the space required to obtain the recommended free installation area for the machine. Thicknessing Thickness table length 520 mm Thickness table width 850 mm Working height min. 3 mm Working height max. 240 mm Working length min. 220 mm Maximum chip removal 5 mm Djdpfxsd Hx Hpe Aqvocp Electrical data Connection voltage 400 V Planer cutterhead Type TERSA Diameter 120 mm Number of planer knives 4 pcs Speed 5000 min¯¹ Planer width max. 520 mm Feed Speed 5/8/12/18 m/min

Condition: new, Year of construction: 2026, Maximum configuration for the professional user. Combination machine with TERSA cutterblock, miter cutting device and pivoting milling spindle Ø 350 mm main saw blade with a maximum cutting height of 118 mm, which is also achieved when the scoring saw blade is installed Scoring device with separate motor and Ø 120 mm saw blade, easily and conveniently adjustable from the outside Highly precise format sliding table made of anodized aluminum on hardened and riveted steel guide rails Large outfeed table (1200 x 650 mm) with roller and extendable aluminum telescope fence up to a maximum of 3300 mm Saw unit can be pivoted from 90° to -45° Pivoting milling spindle from 90° to -45° to the rear into the milling fence Four milling speeds Right/left rotation of the milling spindle Quick changeover to the thickness planer thanks to parallel-opening planer tables 2-stage feed rate on the thickness table Helical toothed steel feed roller for even wood feed Three independent industrial motors With separate saw parallel fence and separate joiner fence With lockable main switch Equipment details: Format fence Immediate control Outfeed table Outfeed table with angle-adjustable telescope stop with degree scale Sliding table with ball contact system made of anodized aluminum Guides made of hardened and ground steel F550S, 15% harder than conventional steel Guides riveted and not glued easy running, quiet and reliable 10-year HOLZKRAFT warranty on wear of the hardened guide rails Cast iron double-pivot saw unit Height adjustment via dovetail guide extremely robust and torsionally stiff for precise cuts located close to the saw blade, bearing on both sides height- and up to 45° angle adjustable standard scoring unit with separate scoring motor 0.55 kW Double-pivot milling unit large, pivoting double-pivot milling unit made of cast iron Milling fence heavy-duty professional design the high-quality milling fence made of cast iron comes standard with fine adjustment 3-way positionable for quick restoration of the setting with fine adjustment via rack and pinion, digital display and aluminum milling fence cheeks Planing units helical toothed steel feed rollers for a constant and even wood feed massive anti-kickback devices prevent workpieces from kicking back 4-knife Tersa cutterblock ensures an optimal planing result table lips for quieter operation Tersa planing cutterblock No more adjustment and screwing Planer knife change in seconds Self-locking particularly quiet Thickness table The thickness table is mounted on four large-dimensioned spindles, which ensure maximum stability under all working conditions Due to the special lifting device, the table position is maintained without fault, even without locking Parallel fence with fine adjustment and quick clamping stable round bar guide made of ground steel interchangeable aluminum ruler No gap, guide rods are overlapping Separate joiner fence large, professional design (1800 x 150 mm) 0-45° pivotable with quick adjustment stable round bar guide made of ground steel Djdpfjcnxa Ssx Aqvecp Simultaneous opening Type: No. 5500557

Condition: new, Year of construction: 2025, FS 41 classic Tersa – Jointer-planer with TERSA quick-change cutterhead system With TERSA cutterhead for ultra-fast cutter blade changes TERSA cutterhead system enables particularly quiet operation Helically toothed steel infeed roller for consistent and uniform wood feed The particularly long, one-piece jointer tables allow for easy planing of workpieces Large jointer fence can remain in its position when the jointer tables are opened Rear-opening jointer tables The high machine weight ensures maximum precision and smooth operation Powerful industrial motor Robust steel/cast iron construction Model: FS 41 Classic Tersa Item No.: 5503414 Technical data ---Technical data, jointer--- Total length of tables: 1800 mm Feed table length: 920 mm Table height: 870 mm Working width: 410 mm Max. chip removal: 4 mm ---Technical data, planer--- Dimensions of planer table: 605 x 420 mm Min./max. working height: 3 / 230 mm Feed speeds: 7 m/min Cutterhead diameter/cutter blades: 72 mm / 3 pcs. Speed: 5200 rpm Motor 400V/50Hz/S6 40%: 5.0 kW (6.6 hp) Dust extraction port diameter: 2 x 120 mm Weight: 270 kg Tersa cutterhead No more adjusting and screwing Cutter blade changes in seconds Self-locking Particularly quiet Planing unit Massive anti-kickback devices prevent workpiece kickback 3-blade Tersa cutterhead for optimal planing result Wood feed Helically toothed steel infeed rollers for a constant and uniform wood feed without marks 13 teeth engage simultaneously for powerful feed Dcedocnxayspfx Aqvep Wear-free compared to rubber infeed rollers Dust extraction hose connection The dust extraction ports of the jointer (1) and planer (2) point in the same direction The hose connection is made from only one side No hose is needed that extends around the machine

Condition: new, - New -Description:TERSA quick-change system for changing planer knives in secondsFour-blade shaft for best planing resultsSmooth running thanks to precision unit and heavy cast iron designLong planing tables for precise planingRobust dressing tables made of ribbed gray cast iron, milled and stress-free, making them insensitive and permanently flatLarge, sturdy aluminum dressing fence with round rod guide (1200 x 150 mm), easily adjustable and tiltable up to 45°With auxiliary fence as standardPowerful 5.0 kW industrial motorSturdy cast steel constructionSlot drilling device can be retrofittedLength (product) approx. 2250 mmWidth/depth (product) approx. 1370mmWeight (net) approx. 465kgJointerTotal length of the tables 2250mmMax. chip removal 8mmDressing fence length 1200mmDressing fence height 160mmSuction connectionSuction nozzle diameter 120mmInstallation informationSpace requirement length 2250mmSpace requirement width/depth 1440mmExplanation of space requirementWorking area length 1000mmWorking area width/depth 3500mmChip removal max. thickness 8mmElectrical dataPower drive motor 5kWSupply voltage 400VMains frequency 50HzItem no. 5503521 Dodpfxjvwf Hre Aqvecp

Condition: new, - Maximum equipment for the professional with Tersa knife shaft.- Ideal for demanding craftsmen and joiners- The particularly long planing tables enable easy dressing of the workpieces- Work tables are made of gray cast iron, because of that insensitive and permanently flat- To the rear, planing tables that open at the same time for short set-up times- Helical-toothed steel feed roller ensures constant and even wood intake- Rubber pull-out roller in the outlet of the thickness ensures even wood pull-out- Material feed at four speeds- Plane thickness table adjustment via handwheel with numerical display for the planing height- TERSA planing knife system enables Knife changes within seconds as well particularly quiet running- The large planing fence (1200 mm x 150 mm) can when opened the planing tables remain in position- The high machine weight ensures the highest Precision and smooth running- Preparation for slot drilling equipment Digital version with electric thicknessing table adjustmentTechnical specificationsTotal length of the tables 2250 mmWorking width 520 mmmax. chip removal 5 mm--- Technical data thickness ---Dimensions thickness table 520 x 850 mmmin./max. Working height 3/240 king length thickness 220 mmFeed speeds 5/8/12/18 m / min Planer shaft diameter / planer knife 120 mm / 4 ed ??5,000 rpmMotor 400V / 50Hz / S6-40% 7.0 kW (9.5 HP)Extraction nozzle diameter 1 x 120 mmWeight 695 kg Slot drilling device (option)Table size 470x230 mmCross / longitudinal stroke 160mm / 110 mmVertical stroke 120 mmExtraction nozzle diameter 1x120 mmManufacturer number 5503511 Dcodpsvwd U Ijfx Aqvop

Condition: new, - NEW -description- Stable cast steel construction- Milling spindle can be swiveled backwards from 0 ° to -45 °- Three spindle speeds from 3500 - 10000 rpm- As standard with right-left rotation of the milling spindle- Large-sized milling unit made of gray cast iron,attached directly to the table- Solid and precise gray cast iron table- Quick and easy speed change- Powerful 5.0 kW industrial motor- Standard curved milling protection hoodEquipment detailsAluminum sliding carriage- Equipped with a thousand times tried and testedBall contact system- torsion-resistant, extremely precise, smooth-running andproblem-free in daily use- 10 year Holzkraft guarantee on wear and tearof the guidewaysGray cast iron milling unit- Attached directly to the router table- Milling spindle mounted high up with precision ball bearings,thus the lowest possible bearing loadand the longest possible service life- 3 milling speeds from 3500 to 10000 rpmPowerful engines- Equipped with a powerful three-phase motorMilling protection- The milling protection is standard for maximum safetywith a height-adjustable guide railand ling stop- Exact milling stop with a quick adjustmentand a fine adjustment with a scale on the stop jaw- The integrated suction connection ensures a clear viewRouter table opening- A large router table opening also enablesthe use of larger flattening cuttersand tenoning and slotting toolsabove and below the tableArc milling protection hood- Included as standard in the scope of deliveryReversible stop jaws- Versatile integrated stop for bridgingthe tool gap- Allows you to work safely withnarrow workpiecesTechnical specifications:Dimensions and weightsWeight (net) approx. 290 kgConnection suctionExtraction nozzle diameter 2 x 120 mmWork tableWorking table length 1000 mmSlide length 1000 mmWorking table width 435 mmSlide carriage width 270 mmTable height 900 mmInstallation informationRequired space length 1945 mmMachine body width / depth 710 mmRequired space width / depth 2220 mmWorking area length 1600 mmExplanation of space requirementsThe dimensions take into account maximum travels or useful king area width / depth 1600 mmMachine body length 1000 mmExplanation of the work areaPlease add the specified dimensions with the space required in order to obtain the free installation area recommended for the ctrical dataConnection voltage 400 VMains frequency 50 HzPhase (s) 3 PhDrive motor power 5.0 kWType of current ACMilling spindleSpindle inclination 0 to -45 °Spindle speed (s) 3500/7000/10000 min¯¹Usable length of the spindle 100 mmSpindle mandrel diameter 30 mmSpindle overhang r table 130 mmMilling tool diameter l diameter can be lowered 180 mmTool diameter max. Tenon milling 275 mmTool diameter file milling 210 mmscope of deliveryArc milling protection hoodAnodized aluminum sliding carriageTelescopic miter fenceAluminum stop jawsItem No. 5502045 Dcodjvwf Ucepfx Aqvjp

Condition: new, Year of construction: 2026, Combination saw-milling machine minimax st 3c F 16 Swiveling saw blade, swiveling milling spindle, and format sliding table made of anodized aluminum Stable steel cast iron construction Large support surface and precise cast iron table High-precision format sliding table made of anodized aluminum (travel 2250 mm) Large rip fence frame (900 x 600 mm) with an extendable aluminum telescope stop up to 2660 mm, featuring professional stop flaps Max. saw blade diameter 315 mm with scoring device, swiveling from 90° to 45° Saw parallel fence with fine adjustment Stable saw unit and large dimensioned double-bearing milling unit ensure maximum stability, precision, smooth running, and long service life Solid and precise machine table made of stress-free cast iron Three milling speeds, manually adjustable from 3500 - 10000 min⁻¹ With right-hand/left-hand rotation of the milling spindle Standard arc milling guard Safety flip stop jaws made of aluminum Two motors with high power reserves Two plug-in handwheels for convenient and quick operation Dimensions and weights Weight approx. 470 kg Dust extraction connection Dust extraction port diameter 2 x 120 mm Dust extraction port diameter saw blade guard 60 mm Electrical data Power of drive motor 2 x 5.0 kW Connection voltage 400 V Mains frequency 50 Hz Milling spindle Spindle inclination 0 – -45 ° Usable length of the spindle 100 mm Dcjdpfx Ashp Rdloqvop Spindle speeds 3500/7000/10000 min⁻¹ Milling tool diameter max. non-tilting 210 mm tilting 180 mm dovetail milling 275 mm Circular saw unit Rip fence length 1600 mm Cutting width with parallel fence 900 mm Max. crosscut width to the left of the saw blade 2660 mm Saw blade inclination 90 45 ° Max. cutting height 90° 90 mm Max. cutting height 45° 63 mm Max. saw blade overhang 90° 100 mm Max. saw blade overhang 45° 78 mm Diameter (main) saw blade 315 mm Explanation diameter (main) saw blade: independent of the scoring saw Speed (main) saw blade 4000 min⁻¹ Sliding table and table Table length 1112 mm Table width 430 mm Scope of supply: Arc milling guard Anodized aluminum format sliding table Aluminum stop jaws Flip stops Location: In stock at 54634 Bitburg - immediately available -

Condition: new, - New -with swiveling sanding unit andoscillating sanding belt F version forVeneer grindingDescription:- The grinding unit can be swiveled up to 45 ° using a lever- The machine stand made of welded steelguarantees high torsional rigidity andvibration-free work.- Oscillating sanding belt with separateGear motor for better grinding results- Oscillation can optionally be switched on- Sanding sole with graphite coating for a higherService life of the sanding belt- Height-adjustable sanding table for usethe entire width of the sanding belt- Height-adjustable additional table with suctionfor grinding radii- The spring-loaded belt tension is the sameTape length differences independently.- With double suction- Extendable roller table extension- With rubberized sanding roller- Veneer edge grinding device with contact shoewith fine adjustment, relief rollersand fence rulers- With grooved infeed ruler for veneer protrusions- Quick changeover of veneer edgespossible on solid wood sandingTechnical specifications:Dimensions and weightsLength approx. 1900 mmWidth / depth approx. 900 mmHeight approx. 1350 mmWeight approx. 290 kgConnection suctionExtraction nozzle diameter 140/100 mmDrive powerOscillation motor 0.25 kWWork table (s)Working table length 960 mmWorking table width 350 mmWork table height adjustment 230 mmHeight adjustment longitudinal table 230 mmCross table height min. 720 mmElectrical dataConnection voltage 400 VMains frequency 50 HzGrinding unitSanding belt length 3000 mmSanding belt width 200 mmBelt speed (s) 20 m / sSanding surface length 1050 mmSanding surface width 200 mmOscillation stroke 20 mmItem No. 5363001 Dcodpovwgbwjfx Aqvsp

Condition: new, - NEW-descriptionCutting plane directly on the saw bladeHeavy steel and cast iron constructionPrecision-guided format sliding carriage made of aluminium,anodized as standardLarge-area table extension guided on a telescopic arm andlongitudinally adjustableExtendable aluminum telescopic fence, angle adjustable with professionalstop flapsRip fence with quick release and fine adjustmentLarge work table made of milled gray cast iron stays permanently flatThe standard table extension and table extension enable easy work with larger workpiecesQuiet running and precise cutsEquipped with a powerful three-phase motorThe large dimensioned cast iron sawing unit is attached twice to the cast iron table and guarantees stability, precision, smooth running and a long service lifeMaximum cutting height is also achieved with the built-in scoring deviceEquipment details:Double cradle saw unitGenerously dimensioned, made of steel/cast ironClose to the saw blade, supported on both sides for precision, smooth running and a long service lifeAdjustable in height and up to 45° with a crankMaximum cutting height is also achieved with the built-in scoring deviceAlso available with scoring unittelescopic stopExtendable telescopic stop up to max. 2550 mmAngle adjustableWith professional stop flapsAluminum sliding carriageWith a thousand times proven ball contact systemInsensitive to dust and dirt due to minimal contact point between ball and trapezoidal rail10-year Holzkraft guarantee on wear and tear on the guidewaysRip fence with round rod guideWith fine adjustment and quick releaseStable round rod guide made of ground steel with a diameter of 45 mmCan be folded down as standard for cutting large workpiecesTechnical specifications:Dimensions and weightsWeight (net) approx. 380 kgConnection suctionSuction connection diameter 120 mmSuction connection diameter saw blade protection 60 mmMachine body length 1388 mmWorking area length 1000 mmMachine body width/depth 689 mmWorking area width/depth 2000 mmSpace required length 5118 mmSpace requirement width/depth 3830 mmelectrical dataConnection voltage 400 VDrive motor power 5.0 kWPhase(s) 3 PhNominal operating mode drive motor S6Type of current ACDuty cycle drive motor 40%Mains frequency 50 HzSliding carriage and tableFormat slide length 2250 mmTable length 840 mmFormat sliding carriage width 270 mmTable width 560 mmFormat sliding carriage height 124 mmTable height 900 mmcircular saw unitCutting width with rip fence 900 mmMax. cutting height 90° 90 mmMax. cutting width to the left of the saw blade 2310 mmMax. cutting height 45° 63 mmtrimming length 2250 mmSaw blade diameter 315 mmSaw blade inclination 90 - 45°Saw blade speed 4000 rpmArt. No. 5504323Ausziehbarer Teleskop-fence to max. 2550 mmWinkeladjustableMit Profi-AnschlagklappenAluminium-sliding tableMit tausendfach bewährtem KugelkontaktsystemStaub- and schmutzunempfindlich durch minimalen Berührungspunkt zwischen Kugel and Trapezschiene10 Jahright hand Holzkraft-guarantee on abrasion der Führungsbahnenrip fence with round rod guidingMit fine adjustment and quick clampingStabile round rod guiding aus geschliffenem steel with 45 mm diameterSerienmäßig tiltable for den Zuschnitt großer WerkstückeTechnische Daten:dimensions and Gewichteweight (Netto) ca.   380 kgAnschluss Absaugungsuction nozzle diameter   120 mmsuction nozzle diameter Sägeblattschutz   60 mmAufstellinformationenTransportbreite   900 mmErläuterung required spaceDie d... Dcodjvyuqfepfx Aqvop

Condition: new, - NEW -- Cutting plane directly on the saw blade- Large dimensioned cast iron saw unit double on the cast iron tablefastened - guarantee for stability, precision, smooth running and long service life- Precision-guided format sliding carriage made of aluminium, standardanodized- 10-year HOLZKRAFT guarantee on wear and tear on the guideways of thesliding carriage- Rip fence with round rod guide and fine adjustment as standard- Large work table made of milled gray cast iron- Quiet running and precise cuts- Enable standard table widening and table extensioneasy work with larger workpieces- Extendable aluminum telescopic fence with angle adjustment andtwo professional folding stops-Made in ItalyTECHNICAL SPECIFICATIONSDimensions and weightsWeight (net) approx. 295 kgConnection suctionSuction connection diameter 120 mmSuction connection diameter saw blade protection 60 mminstallation informationTransport width 700 mmMachine body length 802 mmMachine body width/depth 615 mmSpace required length 3860 mmSpace requirement width/depth 2750 mmExplanation of space requirementsThe dimensions take into account maximum travel distances or usable lengthsWorking area length 1000 mmWorking area width/depth 2000 mmExplanation of work areaPlease add the specified dimensions to the space required to calculate theto obtain the recommended free installation space for the ctrical dataConnection voltage 400 VMains frequency 50 HzDrive motor power 4.0 kWRated operating mode drive motor S 6Duty cycle drive motor 40%Sliding carriage and tableFormat slide length 1600 mmFormat sliding carriage width 270 mmFormat sliding carriage height 124 mmTable length 1020 mmTable width 325 mmTable height 860 mmcircular saw unitCutting width with rip fence 900 mmMax. cutting width to the left of the saw blade 1660 mmtrimming length 1600 mmSaw blade inclination 90 - 45°Max. cutting height 90° 100 mmMax. cutting height 45° 79 mmSaw blade diameter 315 mmSaw blade speed 4000 rpmFURNISHINGAnodized aluminum format sliding carriageHandle for sliding carriagetrimming frameSaw rip fence with round rod guideStops Two professional folding stopstrimming shoeeccentric clamptable extensiontable extensionsaw blade guard&nbsp, Dodpfx Aqjvyup Uovscp

Condition: new, Year of construction: 2025, Belt width: 200 mm Belt length: 3000 mm Dcodpfxshy Iyvs Aqvjp Table size: 960 mm x 352 mm Auxiliary table: 330 mm x 330 mm Veneer sanding attachment: yes Oscillation: yes Sanding unit can be swivelled: yes Dust extraction port: 120 mm Motor power: 3 kW Machine length: 1900 mm Machine width: 900 mm Weight: 310 kg

Condition: new, Year of construction: 2026, The robust design also allows for the processing of longer workpieces. The grinding unit can be swivelled, making it suitable for use as an edge grinding machine. Large, balanced belt pulleys (225 mm) ensure low-vibration operation. Simple adjustment of the grinding belt. High belt speed of 17 m/s. Reversible rotation (right/left). Upper grinding platen with graphite coating. Grinding shoe with 4-point suspension. Equipped with a movable grinding shoe for grinding angled surfaces. Smooth-running work table, even under heavy loads from large workpieces. Optimal price-performance ratio. Additional ESE equipment: Standard with electric table height adjustment. Split table that can be folded out for special edge grinding applications. Drawer-type grinding attachment. Integrated work table lighting. Equipment details: Large, balanced belt pulleys (225 mm) ensure optimal and low-vibration operation. Belt speed: 17 m/s. Equipped with a swivelled professional grinding shoe for grinding angled surfaces. 4-point suspension. Standard with electric table height adjustment. Controls ergonomically arranged on a separate control panel. Standard with drawer-type grinding attachment. Split table that can be folded out for special edge grinding applications. Dimensions and weights: Length approx. 3750 mm Width/Depth approx. 1250 mm Height approx. 1730 mm Weight approx. 520 kg Dust extraction connection. Dust extraction port diameter: 160 / 160 mm Work table(s): Dcjdpfxjff Hdfe Aqvjp Work table height adjustment: 550 mm Work table traverse: 690 mm Electrical data: Power of height adjustment motor: 0.37 kW Power of drive motor: 3.0 kW Connection voltage: 400 V Phase(s): 3 phases Type of current: AC Mains frequency: 50 Hz Grinding unit: Grinding belt length: 7000 mm Grinding belt width: 150 mm Belt speed(s): 17 m/s Grinding shoe length: 270 mm Grinding shoe width: 150 mm

Condition: new, - new -BeschreibungMit TERSA cutter block for sekundenschnelles HobelmesserwechselnTERSA-Hobelmessersystem ermögclear opening particularly geräuscharmen Lonangular verzahnte steel input roller for konstanten and gleichmäßigen HolzeinzugDie particularly langen Abrichttische aus einem piece ermöglichen leichtes Abrichten der WerkstückeGroßer surface fence kann beim opening der Abrichttische in seiner Position bleibenNach rear öffnende AbrichttischeDas hohe Maschinengewicht sorgt for höchste Präzision and ruhigen LonLeistungsstarker Industrie-motorRobuste steel-/GraugusskonstruktionArbeitstische aus Grauguss, nachgeglüht and spannungsfrei, dadurch unempfindlich and dauerhaft planarsurfacing table lip plates for geräuscharmen LonAusstattungsdetails:TERSA-HobelmesserwelleKein Einstellen and Schrauben mehrHobelmesserwechsel in SekundenSelbstarretierendBesonders low noisePerfektes HobelergebnisAbsaugschlauch-AnschlussDie suction nozzle der surface planer and thickness zeigen in the selbe Schlauchanschluss erfolgt from nur einer side wird kein Schlauch benötigt, der um the machine veStabil ausgelegter KettenantriebAntriebsräder aus steelMassiver GraugusslagerbockHobelwerkMassive Rückschlagsicherungen verhindern den kick-back from WerkstückenTERSA-Hobelmesserwelle with three Messern sorgt for ein optimales HobelbildDer MaterialeinzugSchrägverzahnte Stahleinzugswalzen for einen konstanten and gleichmäßigen Materialeinzug without AbdrückeMehreright hand Zähne greifen gleichzeitig for kraftvollen feederVerschleißfrei im Gegensatz zu GummieinzugswalzenTechnische Daten:dimensions and Gewichtelength (Produkt) ca.     2015 mmweight (Netto) ca.     330 kgwidth/depth (Produkt) ca.     990 mmdrive powercapacity driving motor     5 kWsurface planertotal length der tables     1800 mmchip removal max. surface planer     4 mmworking height     900 mmAnschluss Absaugungsuction nozzle diameter thickness     2 x 120 mmAufstellinformationenrequired space length     2015 mmMaschinenkörper width/depth     596 mmrequired space width/depth    1 460 mmworking dimensions length     1000 mmErläuterung required spaceDie dimensions berücksichtigen maximale Verfahrwege or Nutzläking dimensions width/depth     3500 mmMaschinenkörper length     659 mmErläuterung zu working dimensionsDie angegebenen dimensions bitte with dem required space addieren, um the for the machine empfohlene freie assembly area zu cknessDickentisch length     605 mmworking height thickness max.     230 mmDickentisch width     420 mmchip removal max. thickness     4 mmworking height thickness min.     3 mmElektrische DatenAnschlussspannung     400 VStromart     ACPhase(n)     3 PhNetzfrequenz     50 HzHobelmesserwelleHobelwellentyp     TERSAHobelwellendrehzahl     5200 min¯¹Hobelwellendurchmesser     72 mmplaning width max.     410 mmnumber of Hobelmesser     3 Stfeederfeed speed     7 m/minincluded in deliveryTERSA-Hobelmesserwelleeloxierter Aluminium-surface fenceNo. 550 3414 Djdpovwga Hofx Aqvscp

Condition: new, - NEW -- With TERSA cutter block for secondsChange planer knives- TERSA planing knife system enables particularlyquiet running- Helical-toothed steel feed roller forconstant and even wood intake- The particularly long planing tables from onePiece allow easy dressing of theWork pieces- Large planing fence can open when openingthe planing tables remain in position- Planing tables that open to the rear- The high machine weight ensures the highestPrecision and smooth running- Powerful industrial engine- Robust steel / cast iron construction- work tables are made of gray cast iron,post-annealed and stress-free, therebyinsensitive and permanently flat- Table lips for quiet runningEquipment detailsTERSA planing knife shaft- No more adjusting and screwing- Blade change in seconds- Self-locking- Particularly quiet- Perfect planing resultSuction hose connection- The suction nozzle of the planer and thicknesspoint in the same direction.- The hose connection is made by just oneSide off.- No hose is needed aroundthe machine passes ve- Stable chain drive- Steel drive wheels- Solid cast iron bearing blockPlaning mill- Prevent massive kickback protectionthe kickback of workpieces- TERSA planing knife shaft with three knivesensures an optimal planing patternThe material feed- Helical steel feed rollers for oneconstant and even material intakewithout prints- Multiple teeth grip at the same time for powerfulFeed- Wear-free in contrast to rubber feedrollingTechnical specifications:Length approx. 1725 mmWidth / depth approx. 880 mmWeight approx. 270 kgDressing chip removal max. 4 mmExtraction nozzle thickness 2 x 120 mmThick working height min. 3 mmThick working height max. 230 mmThickness of the chip removal max. 4 mmDrive motor power 4 kWConnection voltage 400 VMains frequency 50 HzPlaner knife shaft type TERSANumber of planing knives 3 pcsSpeed ??5200 min¯¹Planing width max. 300 mmFeed speed 7 m / minItem No. 5503031Storage location 97447 Gerolzhofen- free loaded- Dcsdpfx Aqjvwgaasvsp

Condition: new, - New -Description:- Vertical version for splittingShort and meter wood- Robust and solid construction- Shock and scratch resistant due to high qualitypowder coating- Fast, tool-free gap height adjustment- Low base plate for easy,effortless loading of large logs- Phase inverter on all 400V models- Convenient transport with hand drawbardue to standard chassis with largePneumatic wheels and additional support wheel- Space-saving storage through simplelowerable cylinder- Powerful industrial hydraulic system- Two-hand safety circuit- With splitting material holderTechnical specifications:Dimensions and weightsLength approx. 1050mmWidth/depth approx. 1700 mmHeight approx. 2500mmWeight approx. 373.1 kgdrivePTO speed 540 rpmInput power 5.5 kWelectrical dataConnection voltage 400 VMains frequency 50 Hzdevice dataSplitting power max. 26.1 tGap length min. 560 mmGap length max. 1100 mmLog diameter min. 80 mmLog diameter max. 400 mmhydraulic systemHydraulic oil tank capacity 30 lItem No. 5981031 Dedpfovwfziox Aqvocp

Condition: new, The work table made of heavily ribbed gray cast iron andguarantee the base made of welded steelTorsion resistance and vibration-free workingHigh quality machine at a real entry-level priceUnique in this performance class:- Format sliding carriage made of anodized aluminum for the highestcutting precision- Cutting plane directly on the saw blade- Swiveling saw blade unit from 90 - 45 °- Table bracket with aluminum crosscut fence and adjustableStop flap for plates and large workpieces- Rip fence with round bar guide and fine adjustment- Powerful engine- Made in EuropeDimensions and weightsWeight (net) approx. 170kgDust extraction connectionExtraction nozzle diameter 120mmExhaust nozzle diameter saw blade protection 60mmTransport width 680 mmWorking area 1600 mm x 2300 mmSpace requirement 2613.5 mm x 2134 mmPlease add the specified dimensions with the space required to obtain the recommended free space for the dimensions take into account maximum travels or usable lengthsElectrical data400 V supply voltageDrive motor 1.8 kWPhase (s) 3 PhNominal operating mode drive motor S6Current type ACDuty cycle drive motor 40%Mains frequency 50 HzSliding carriage and tableFormat sliding table 1140 mm x 200 mm x 70 mmTable 1024 mm x 224 mm x 900 mmsaw unitCutting width with rip fence 700 mmMax. Cutting height 90 ° 67mmMax. Cutting width to the left of the saw blade 1200 mmMax. Cutting height 45 ° 40mmEdging length 1200 mmSaw blade diameter 250mmSaw blade inclination 90 - 45 °Saw blade speed 3900min¯¹scope of deliverytable extensionAnodized aluminum sliding tableRip fence with round bar guide and fine adjustmentAluminum folding stopEccentricItem No. 5504113 Dcsdsvxr S Rjpfx Aqvop

Year of construction: 2025, condition: new, Rollers: 4 Roller width: 60 mm Roller diameter: 120 mm Suspension travel: 20 mm Speeds: variable, 3 - 18 m/min. Dcodpfx Aeg Ez Sisqvsp Stand: Stand 1050 plus Motor power: 0.75 kW

Condition: new, - new -Description:- Vertical design for splittingshort and meter logs- Robust and solid construction- Impact and scratch-resistant thanks to high-qualitypowder coating- Quick, tool-free splitting height adjustment- Low base plate for easy,{loading of large logs- Phase inverter on all 400 V models- Convenient transportation with manual drawbarthanks to standard chassis with largepneumatic wheels and additional support wheel- Space-saving storage thanks to easylowerable cylinder- Powerful industrial hydraulic system- Two-hand safety circuit- With splitting material holderTechnical data:Dimensions and weightsLength approx. 1050 mmWidth/depth approx. 1700 mmHeight approx. 2500 mmWeight approx. 282 kgDrivePTO speed 540 min¯¹Device dataSplitting force max. 23.4 tSplitting length min. 560 mmSplitting length max. 1100 mmSplitting material diameter min. 80 mmSplitting material diameter max. 350 mmHydraulic systemTank capacity hydraulic oil 24 . 5981023 Dsdpfxsvxr Rye Aqvscp

Condition: new, Description: Planer Surface planer with TERSA quick-change planing knife system With TERSA cutterblock for changing planing knives in seconds TERSA planer blade system enables particularly quiet running Helically toothed steel infeed roller for constant and even wood infeed The particularly long, one-piece planer tables enable easy planing of the workpieces Large planing fence can remain in position when the planing tables are opened Dressing tables open to the rear The high machine weight ensures maximum precision and smooth running Powerful industrial motor Robust steel/cast iron construction Special equipment features Work tables are made of gray cast iron, annealed and stress-free, making them robust and permanently flat Table lips for quiet running Equipment details TERSA planer cutterblock No more adjusting and screwing Planer blade change in seconds Self-locking Particularly quiet Perfect planing result Suction hose connection The extraction nozzles of the jointer and thicknesser point in the same direction. The hose is connected from one side only. No hose is required to reach around the machine. Drive Dedpfx Aeu Diwleqvocp Sturdy chain drive Steel drive wheels Solid cast iron bearing block Planing unit Solid kickback guards prevent workpieces from kicking back 3-blade TERSA shaft ensures an optimum planing pattern The material infeed Helical-toothed steel feed rollers for constant and even material feed without marks Several teeth engage simultaneously for powerful feed Wear-free in contrast to rubber feed rollers Technical data Jointer total table length 1510 mm Jointer working width 300 mm Jointer chip removal max. 4 mm Thicknessing dimensions thicknessing table 565 x 300 mm Thick working height min. 3 mm Thick working height max. 230 mm Thicknessing feed speeds 7 m/min Planer shaft speed 5200 min-1 Planer shaft diameter 72 mm Number of planing knives 3 pcs. Electrical connection 400 V Motor power 4.0 kW Suction nozzle diameter 2 x 120 mm Weight 270 kg Optional slot drilling device Table size 470 x 220 mm Optional slotted hole drilling device transverse/longitudinal stroke 160 mm / 110 mm Optional slot drilling device vertical stroke 120 mm Scope of delivery & equipment TERSA planer cutterblock Anodized aluminium planing fence

Condition: new, Year of construction: 2026, LAB 300 PLUS F 16 TERSA - Universal combination machine with aluminum sliding table and three milling speeds for sawing, milling, planing/thicknessing, and optional mortising torsion-resistant steel cast iron construction machine table made of cast iron, hardened and ground easy-running, anodized aluminum sliding table, 10-year warranty on wear of guide rails large fence system with extendable aluminum telescope fence and folding stops with combination saw fence with 45° quick adjustment max. saw blade diameter 315 mm with optional scoring unit, pivotable from 90°-45° helical steel feed roller for consistent wood feed during thicknessing four milling speeds, manually adjustable standard with right/left rotation of the milling spindle three independent motors for each working unit Scope of delivery: Combination fence/parallel fence Arc milling guard Tersa cutterhead Anodized aluminum sliding table Aluminum fence cheeks Folding stops Eccentric clamping arm Model LAB 300 PLUS F 16 Tersa Item No. 5500314 Technical data ---Technical data circular saw--- Dsdpfx Ascnxa Nsqvjcp Fence length 1600 mm max. saw blade diameter with scoring 315 mm max. cutting height at 90° / 45° 100/79 mm max. ripping width to the left of the saw blade 1660 mm Cutting width on the parallel fence 800 mm Saw arbor speed 3500 rpm Saw blade inclination 90° - 45° ---Technical data planer--- Working width 300 mm Planer table length 1260 mm Cutterhead speed Cutterhead diameter / number of planer knives 72 mm / 3 pcs ---Technical data thicknesser--- Table dimensions 300 x 450 mm min. / max. working height 3 mm / 220 mm max. chip removal 4 mm Feed rate 7 m/min ---Technical data table saw--- Usable spindle length 100 mm max. tool diameter 180 mm, can be recessed max. tenon tool diameter 275 mm max. tool diameter, can be recessed 140 mm Spindle speed 3500/600/800 rpm Spindle diameter 30 mm Motor power 400 V / 50 Hz / S6 - 40% 4 kW (5.5 hp) S6 40% Weight 430 kg Dust extraction port diameter 4 x 120 mm Dust extraction port diameter saw blade guard 60 mm Sliding table with ball bearing system equipped with a proven ball bearing system permanently easy-running thanks to hardened and ground guides not susceptible to dust and dirt due to minimal contact point between the ball and the trapezoidal rail 10-year HolzKraft warranty on wear of the carbide guide rails Dust extraction hose connection The dust extraction ports of the planer (1) and thicknesser (2) point in the same direction. The dust extraction hose can therefore be connected to the machine from the same side for both types of planing. You do not need a hose that goes around the machine. Planing units helical steel feed rollers for a constant and even wood feed massive anti-kickback devices prevent the workpiece from kicking back 3-knife cutterhead ensures an optimal planing result

Condition: new, Year of construction: 2025, Suction nozzle diameter: 260 mm Nominal volumetric flow rate: 7700 m³/h Chip collection bag volume: 2 x 290 l Filter cleaning: manual Dcjdpfx Aqehw I Szovsp Motor power: 4.8 kW Dimensions: 1900 x 670 x 2800 mm (L x W x H) Weight: 88 kg

Condition: new, Year of construction: 2025, Chip extraction unit ASA 7703 mobile, with extraction unit that can be rotated by 180° Dodpfehk S Stex Aqvecp For milling, planing, and sawing chips (not suitable for dust) Extraction unit can be rotated by 180°, allowing for extraction from below or above Robust metal fan impeller Comes standard with high-quality chassis for improved stability and easy maneuvering Quick-release fasteners for filter and chip bag Fine filter bag, double-woven Dimensions and weights Chip collection volume 2 x 290 l External diameter of extraction nozzle, inlet 260 mm External diameter of extraction nozzle, outlet 3 x 120, 1 x 100 mm Length approx. 1900 mm Width/Depth approx. 670 mm Height approx. 2800 mm Weight approx. 88 kg Electrical data Idle speed 2950 min¯¹ Power consumption 4.8 kW Connection voltage 400 V Mains frequency 50 Hz Filter Filter area 2 x 5.98 m² Noise emission Maximum sound pressure level 98.3 dB(A) Volume flow Nominal volume flow 7700 m³/h Maximum negative pressure 2800 Pa Scope of supply: Two filter bags, two chip bags Location: In stock at warehouse 54634 Bitburg - available for immediate delivery -