Used Furnace for sale (752)

Condition: new, Year of construction: 2024, machine/vehicle number: 05004100140, Drying and Burn-in Furnace TRO, Model III Hnodpfx Aajh Tytbscou For drying racks with max. 50rods, useable size 100x140cm, outer dimensions: approx. 2520mm wide x 1870mm deep x 2300mm high, useable space: approx. 1700x 1350x 1660cm. Suitable for vaporisation of low amounts of solvent, authorised for inks and solvents up to hazard class A II, according to safety requirements DIN EN 1539 (max. permitted solvent quantity: 110g per charge). Equipped with control of the minimum exhaust volume and a heating system in regard to the exceedance of the max. temperature. Fixing and drying temperature: up to max. 180°C. Power connection: 400V/50Hz, 21kW, weight: 1,000kg, varnishing: corps RAL 7035 (light grey), doors RAL 7037 (dust grey). Special varnishing upon request. Chamber dryer, all-steel construction, with good thermal insulation. Simple insertion of drying racks by means of easy-to-open wing doors. The air is sucked out of the drying chamber by ventilators, is blown through thermostat-controlled heating registers and re-fed temperature-controlled to the drying chamber. The solvents released during the drying process are dissipated from the exhaust side of the ventilator while supply air gets into the drying chamber. The horizontal air guide in the drying chamber guarantees an even temperature control. The required temperature can easily be adjusted via actual and nominal value thermostat. Overheating protection by safety thermostat. Particularly suitable for fixing and drying of textile inks, flock glues as well as for burning-in of plate and aluminium signs up to 180°C. - Various drying racks for different applications available. - We recommend the installation of a gas warning unit. ATTENTION: Not permitted for solvents! Not permitted for foods!

Year of construction: 2001, condition: used, machine/vehicle number: 12117, Continuous Furnace / Brazing Furnace Max. operating temperature: 1120°C Normal operating temperature: 1050°C Conveyor Belt: Useful width of conveyor belt: 250mm Useful height of conveyor belt: 150mm Heating Chamber: Heating Chamber Length: 1530mm Heating Chamber Width: 500mm Height: 500mm Installed Power, Gas: 33kW Number of Heating Zones: 3 Number of Control Zones: 3 Voltage: 3 x 400/230V Frequency: 50Hz Hnedpfxowku N Uo Aacou You are welcome to visit us by appointment.

Year of construction: 2017, condition: ready for operation (used), Vötsch VAW 60/100 Heat Oven / Heating Cabinet / Furnace Internal dimensions: 600mm x 1000mm x 600mm (W x D x H) Hsdpfx Aswykz Sjacjnu External dimensions: 1800mm x 1800mm x 2200mm (W x D x H) Rated temperature: 650 °C Year of manufacture: 2017 Nominal power: 20 kW You are welcome to arrange a viewing. We can organize cost-effective shipping for you upon request. You will receive a proper invoice. For international customers, a net invoice can be issued provided a valid VAT ID number is supplied. Subject to prior sale. Visit our shop to see more of our offers. All listed company names and trademarks are the property of their respective owners and are used for identification and description purposes only. Deviations from technical data as well as errors in the description of the item may occur and are reserved.

Year of construction: 1990, operating hours: 16,400 h, condition: good (used), AICHELIN ROTARY FURNACE WITH HESS PRESS AND WASHING MACHINE description: Rotary hearth furnace AichelinModel: RDLGs-R-SJ-1,5m. Year: 1990 External dimensions: 2460 x 2460 x 2335mm Operation: Gas fired with 4 Rekumat self-recovery radiant tube burners. Consumption electrical connection: Connection voltage 380V/50Hz Control voltage 220V/50Hz Total nominal consumption 15Kva Nominal consumption motors 11,7Kva Max. temperature: 950º Cycle time approx. 50 seconds. Hess PressModel : HP 1-48 Year : 1990 Outside dimensions : 1830 x 1650 x 2630mm Empty Weight: 3000kg Hnsdsnzhx Hspfx Aacsu Max Cooling Unit: 230kg of SteelMax Workpiece Size: Approximately 210mm Caber Washing MachineModel: 350 T Year: 1990 Outer dimensions: 7100 x 1470 x 2700mm Unladen weight: 4000kg Loading height: 1180mm

Year of construction: 1966, condition: used, machine/vehicle number: 6498, Article number: MA1020 Manufacturer: Naber Art: 45 S Hnedpfx Aaedd Rw Eocju Year: 1966 Machines-Nr.: 6498 Taxes: Naberterm Length [mm]: 1000 Width [mm]: 750 Height [mm]: 700 Weight (kg]: CA. 120) Rated power: 380V / 6 KW Table size LxW: Internal dimensions: 230 X 230 X depth 300 mm

Year of construction: 2010, condition: used, working temperature 250 °C working pressure 12,5 bar workpiece diameter 4.300 mm workpiece length 8.000 mm weight of the machine ca. 60 t SCHOLZ AUTOKLAV - 4300 x 8000 for the curing of components made from composite carbon fiber mats (PREPREG). The Autoclave was electrically refurbished in 2021. It is certified for use in the aviation and aerospace sectors. Furthermore, a complete and uninterrupted calibration record is available up to the present day. The autoclave is equipped with a monitoring system for temperature and pressure zones. Operating hours: - vacuum pump: 9.132h - fan: 15.497h The Autoklav is in very good condition and can be inspected under power at any time in the Swiss factory location (aviation company). Hsdpewfc Saefx Aacenu The machine video from the production plant will be shared on request. - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - #Tags: 4300x8000 | 4.300 x 8.000 | 4.300x8.000

Condition: excellent (used), Nabertherm N450 ceramic firing kiln, maximum temperature 1280 degrees C. German-made kiln. The kiln is equipped with a very intuitive controller with 6 programs. New spirals have been installed in the kiln, which guarantee the achievement of maximum temperature. Chamber with a capacity of 450 liters. Chamber dimensions: Height 100 cm Width 60 cm Depth 75 cm External dimensions Height 182 cm Width 103 cm Depth 145 cm Hnodpewdzt Hefx Aacou Power supply 400 V Power 24 kW Maximum temperature 1280 degrees C Kiln in very good condition.

Condition: ready for operation (used), Year of construction: 1995, functionality: fully functional, machine/vehicle number: Seriennr.: 4046, Equipment: documentation/manual, Ingot casting belt 600 Hedpfx Aou S N Aheacsnu Zinc melting furnace ZSO 600 / 700 B

Condition: ready for operation (used), Nabertherm N41 kiln, chamber furnace, annealing and hardening oven Heating capacity: 12 kW Maximum temperature: 1150 °C Internal dimensions: 350 mm x 500 mm x 260 mm (W x D x H) You are welcome to arrange an inspection. We can organize cost-effective shipping for you! Hjdpfjwty S Tex Aacenu You will receive a proper invoice. For international customers, a net invoice can be issued, subject to a valid VAT ID. Subject to prior sale. Visit our shop to view further offers. The company names and trademarks mentioned are property of their respective owners and are only used for identification and description of the products. Technical data may vary, and errors in the item description are reserved.

Condition: good (used), Year of construction: 1991, functionality: fully functional, load capacity: 650 kg, EROS SIZE 7 furnace for carburizing, carbonitriding and quenching. Refractory exchanged with Kanhtal resistors. Useful dimensions. 700x450x1150mm Hsdpsu A Tf Defx Aacsnu Chamber dimensions: 750x560x1540 mm Outer dimensions (layout) 2500x 3715x 4500 mm Furnace heating power: 85 kW Oil heating power : 35KW Furnace working temperature : 20-950ºC Cesats dimensions: 700x1150x150 mm (capacity 3 superimposed baskets) Oil tank capacity: 4500 liters Maximum load approx : 600-650 kg Control equipment UDC-5000 (potential carbon control) Carbon sensor rod (with co2 cleaning) Few hours of use

Condition: good (used), Year of construction: 2002, functionality: fully functional, (Please tell us your offer price) Sale only within Europe, incl. Turkey Price without packaging; delivery condition: FCA (machine location) ===== Technical data see handout. All warranty rights are excluded. For the correctness of the technical data and year of construction, for the completeness of accessories and tool equipment, Hnedpfx Aaewg Hlaocju and for compliance with all safety and environmental protection requirements specified in the accident prevention regulations. No sale to private individuals. Sales only within Europe, incl. Turkey Price without packaging; Delivery condition: FCA (machine location) ===== Technical data please see handout in attachment. German text leading language. Without any guaranty and warranty, including completeness of tools & accessories as well as environmental and safety regulations. No private sales.

Year of construction: 1996, condition: used, functionality: fully functional, load capacity: 650 kg, IPSEN DAQ 7-8 Manufacturing Year : 1996 Heating : Gas Heaters : Recon 2 (x3) Charge Capacity : 650kg Brutto Hsdpoxivumsfx Aaconu Charge dimensions : W:650mm L:1173mm H:550mm Protective Gasses : Endogas Ammonia Nitrogen The furnace can be operated with existing conditions.

Condition: good (used), Laboratory Tube Furnace Naber R70/9 Hodpfody Huyjx Aacjnu - Housing made of high quality structural steel. - The diameter of the tube is 70mm - The length of the tube is 1000mm - Tube made of sillimantine, works with two end caps 60 - damaged on one side. - Silent electronic relay - Maximum temperature - 1200C - Temperature drop - 10 C / min - Programmable temperature curve

Condition: new, 7 pieces heating coil new for a melting furnace Fulmina SOU 20E, Technical data: Reversible element with connection ends Ø 10 x 270 mm power: 10.000 Watt Voltage: 220 Volt cold resistance: 4,60 (± 5%) Ohm wire diameter: 4,50 mm coil inner Ø: 29 mm leg length: 240 mm Number of legs: 3 x 8 pieces Wire quality: CrFeAl Y 3 heating coils are a complete set in this model (the pictures of the melting furnace serve the representation and show the model in which the heating coils were installed, they fit however also into other models with smaller or higher achievement, it changes only the number of pieces) immediately available from stock Hnedpfx Aod Tx A Eoaceu

Condition: defective spare-parts repository (used), Stainless steel housing for a vacuum furnace with a molybdenum heating chamber. You are welcome to come by for a viewing by appointment. Hjdpfxjvrh Ius Aaconu

Condition: used, Year of construction: 2013, operating hours: 6,000 h, functionality: fully functional, the following is included: - Hardening furnace (vacuum oil quenching furnace) Hedpfewlvhhex Aacjnu - Control cabinet for hardening furnace - Internal water tank with pump units and control box - Control box for water cooling - Internal nitrogen pressure vessel - External platform for cooling unit + connection points for nitrogen batteries (nitrogen battery containers not included, must be rented) - 7 hardening baskets - Red transport and loading trolley - Parts washing tank for complete baskets with compressed air and drip tray -> System has approx. 6,000 operating hours -> The pictures are up-to-date, only the date on the images is not correct

Condition: new, fuel type: electric, tank capacity: 1,000 l, continuous power: 14 kW (19.03 HP), total length: 1,000 mm, total width: 1,000 mm, total height: 1,000 mm, ⭐⭐⭐⭐⭐ (5.0) ⚡️ Top Service ⚡️ Fast Delivery ⚡️ Great Support! ✈️ Plus shipping costs – Shipping available upon request. Fast delivery: Only 4 weeks after receipt of payment! ➖➖➖➖➖ ✳️Maintain your liquidity! We offer a variety of financing models to ensure your investment has the greatest chance of success. Contact us today to learn more about our hire purchase, warranty, or leasing programs. ➖➖➖➖➖ ✨✨Buy directly from the manufacturer and secure the price and quality advantage!✨✨ ➖➖➖➖➖ ⭐ Powder furnace with electric heating - MATOVENB-101010 ✔️ Internal dimensions: 1000 mm L * 1000 mm W * 1000 mm H ✔️ External dimensions: 1500 mm L * 1300 mm W * 1900 mm H ✔️ Electric heating output: 12 kW/h ✔️ Fan: 1,500 m3/h 80 mm SS ✔️ Recirculation fan output: 0.75 [kW/h] ✔️ Total 14 kW/h +- 10% ✔️ Digital heat control with continuously adjustable temperature up to 220°C ✔️ Sandwich panels: Interior: 1.2 mm galvanized steel, exterior: 1.2 mm powder-coated steel ✔️ Curing temperature, curing time, and exhaust fan function are adjustable ✔️ A beep sounds at the end of the curing time ✔️ Insulated door with special locking systems ✔️ Insulation: 150 mm (50 mm rock wool and 100 mm fiberglass) ✔️ Control panel: 1 🔥 MATOVENB-101010 – Your versatile industrial oven for drying and curing processes! 🔥 Whether powder coating, wet paint, plastics processing, or other thermal processes – the MATOVENB-101010 is your reliable solution for professional drying and curing processes up to 230°C! 🌡️ 🚚 Maximum loading flexibility • Use with a mobile workpiece trolley possible • Optionally with a loading rack system for small batches ⚙️ Intelligent control – just the way you need it ✅ PID control (optional) for precise temperature control ✅ Touchscreen control panel & smartphone control 📱 (optional) ✅ Weekly & monthly reports at the touch of a button (optional) ✅ Timer function: freely programmable from 10 minutes to 24 hours ⏲️ ✅ Automatic shutdown after the end of the process ♨️ Ramp heating mode (optional) Precisely control the temperature profile and holding times, e.g. E.g.: • Reach target temperature within a defined time • Maintain desired time • Controlled cooling to target temperature • Automatic notifications of process events 🛡️ Safety is our priority 🟢 Safety sensor to prevent overheating 🟢 Automatic shutdown in the event of a fault 🟢 Acoustic warning signals in the event of errors 🟢 Solvent and fume extraction via automatic venting ⚡ Customized energy and heating system 🔌 Selectable heating systems: Gas, Diesel, Electric, or Hybrid (two combined heating modes) (optional) Hnodpswfpp Eefx Aacsu 🔥 Also available with an extension up to 400°C for high-temperature processes (optional) 🧠 No repeated settings necessary! The furnace saves your process parameters – batch by batch. This saves you time and avoids errors. 📢 And best of all: If you have special requirements – we also build customized furnaces according to your specifications! Contact our team of experts for a personalized consultation! Request now – Make your business fit for the future! ⭐Follow us for new campaigns⭐ ☀️ 2-YEAR WARRANTY ☀️

Condition: ready for operation (used), Heat treatment furnace, annealing furnace, furnace, Used equipment Manufacturer: Budapest Electric Cable Factory Overall dimensions: 890 x 1350 x 1510 mm Weight: 785 kg Hnedpfx Ajuhmaceacsu Electrical data: 400 V, Temperature controller adjustable up to 1100°C +temperature controller in the electrical box

Year of construction: 2000, condition: excellent (used), functionality: fully functional, maximum load weight: 7,000 kg, working height: 1,750 mm, The gas nitration vacuum oven is made up of all the steps involved in gas nitration, carburizing, and tempering. Hnsdpfsu T N Efjx Aacou The machine is in very good condition.

Year of construction: 2006, condition: good (used), Kiln Superturbo, Pulsar model, 180 mc, intermittent type with a firing temperature till 1150°C, and a maximum temperature of 1200°C, equipped with 24 high-speed burners, n° 1 wagon inside the chamber, n° 1 vertical door, reverse induction chimneys, cowl for the expulsion of the smokes, automatic control panel with ATR 313, lining in ceramic fibre, high density, 1260°C type; 4 Heat exchangers for hot combustion air. Hnodpfxehgkdqs Aacou Thermal Power 3,2 MW Dimensions 7x7x4 meters, capacity of wagoon 80 tons.

Year of construction: 2020, condition: like new (used), functionality: fully functional, conveyor belt length: 8,000 mm, temperature: 1,200 °C, Tunnel Type Enamel Cooking Ovens are based on the principle of hanging the workpiece to be fired on the oven conveyor and firing at maximum 1200C. These types of furnaces are internally rotating furnaces, after the workpiece is hung on the conveyor (maximum gross output 1 000 kg/h), it is provided to be fired (firing zone 10meters) or dried while traveling at a certain speed according to the thickness and m2 area of the part. Tunnel Type Enamel Cooking and Drying Ovens are specially designed with our expert engineering staff. Our Tunnel Type Enamel Cooking and Drying Ovens are also manufactured as assembled. Thanks to this feature, it can be easily assembled and moved to other areas if desired. In the industry, it is preferred by high-capacity production enterprises. Hjdpfx Ajvcdr Deacsnu

Year of construction: 2010, condition: refurbished (used), Vacuum furnace for heat treatment of metals with a molybdenum chamber. A high vacuum of 10^-6 mbar is achieved in the furnace. Maximum operating temperature 1300 C. Dimensions of the working chamber: 0.35 x 0.42 m diameter x height. Molybdenum heating chamber. Closed circuit cooling system with a buffer tank Pumping system with a mechanical and turbomolecular pump. Ability to perform processes: • Annealing in high vacuum • Stress relief • Vacuum brazing Hjdpfx Aon Snx Heacenu • Vacuum brazing • etc. The stove is 100% functional after modernization. Sales with installation and commissioning at the customer's place. The final price depends on the scope of modernization, agreed individually with the client. If you have any questions, please contact us.

Year of construction: 2000, condition: excellent (used), Furnace SAFF12m³ for ceramic fiber double door with double wagons(2+2). With forklift wagon movement Hnodpsv Upq Aofx Aacju

Year of construction: 2020, condition: used, machine/vehicle number: KW-50S/SW/20/01, KW50S warming chamber, furnace The device is designed for thermal processing of materials whose flash point is higher than 300 degrees C. Hnedpfx Aju Hk Epoacou The device consists of two independent operating chambers. Each chamber has its own control system. The chambers have windows that allow the tracking of the device's operation and a lighting function. The chamber has the ability to achieve ramp temperatures up to 120 deg C. The warming chamber is built as an independent panel structure mounted on a frame. The connection of the individual elements is carried out by means of welds, rivets and screws, without any additional structural elements. The connection points of the panel structure are sealed with rubber tape and silicone adhesives. Air circulation inside the chamber is forced by centrifugal fans installed above the heaters.

Condition: good (used), Year of construction: 2014, functionality: fully functional, machine/vehicle number: PO140315, NorthGlass AG1B50 glass tempering furnace. For technical data, please see the PDF file. Hnedpfx Asu T Ib Sjacou