Used Eisen Und Hammerwerk Gmbh for sale (69,836)

Year of construction: 2010, condition: used, functionality: fully functional, machine/vehicle number: BA 20090966, For sale is a film die / single-channel die from the manufacturer EDS GmbH, Austria, type FK-TID 1650mm, manufactured around 2010. General information: • Manufacturer: EDS GmbH, Austria • Type: Film die FK-TID 1650mm • Serial number: BA 20090966 • Year of manufacture: approx. 2010 Dwedpfxe Ahm Tvj Acyjd • Lip width: 1,650 mm • Opening ratio: 0.5 – 1.5 mm • Weight (approximate): 970 kg • Nominal torque of screws: 70 - 70% for operating temperatures of 17.8°C - 288°C - 60% for operating temperatures above 288°C • Electrical equipment: 240 volts, single-phase • Total power: 27,000 watts • Number of control zones: 16 Condition Used, fully functional. • Sale from location (EXW) • Further information and additional photos available upon request. • Errors, changes and prior sale reserved.

Condition: new, Year of construction: 2022, functionality: fully functional, type of input current: three-phase, power: 50 kW (67.98 HP), input voltage: 400 V, fuel: domestic gas H, overall weight: 2,200 kg, nominal power: 50 kW (67.98 HP), input frequency: 50 Hz, continuous power: 50 kW (67.98 HP), input current: 72 A, Equipment: documentation/manual, For sale: new and unused 2G g box 50plus combined heat and power (CHP) unit from 2022. This is a 2G Energietechnik g box 50plus, configuration as70 4, suitable for simultaneous generation of electricity and heat using natural gas. The unit has never been put into operation and is in new condition. At full load, the CHP unit delivers 50 kW of electrical power and approximately 104 kW of thermal power. The unit is designed for 400 V and 50 Hz and is equipped with a Liebherr G924 natural gas engine and a Leroy Somer LSAH 44.3 generator. Dsdpfx Asz Hngmocyowd Technical specifications: • Manufacturer: 2G Energietechnik GmbH • Type: g box 50plus • Configuration: as70 4 • ID number: H1214 • Year of manufacture: 2022 • Electrical power: 50 kW • Thermal power: approximately 104 kW • Rated voltage: 400 V • Rated frequency: 50 Hz • Rated current: 72 A • Weight of CHP module: approximately 2,200 kg • Fuel: natural gas • Electrical efficiency: approximately 34.5 percent • Thermal efficiency: approximately 71.8 percent • NOx emissions: less than 125 mg per Nm³ • Sound pressure level of CHP: approximately 55 dB(A) at 1 meter The offered package consists not only of the CHP module. The installation also includes two Viessmann boiler bodies, one Viessmann Proflame VM IV 3 gas burner, a separate control cabinet, and various flue gas components, fittings, and related documentation. The original new price of the complete installation was approximately €189,000. The installation comes from a project for which it was ultimately not used. The various main components are from 2022 and have been stored without being put into operation. Due to the size and composition of the installation, we advise interested parties to contact us in advance for further technical information, photos, documentation, and an overview of the components available. An inspection is, of course, possible (location: Winterswijk, Netherlands). Loading onto the buyer's transport vehicle is possible on site.

Condition: used, Machine: Temperiertechnik GmbH SES Erhitzungsanlage Dwjdpfx Ace Aikkdoyed

Condition: repair required (used), Year of construction: 2010, operating hours: 7,700 h, functionality: not functional, machine/vehicle number: 15158-10, working range: 4,000 mm, sheet thickness (max.): 12 mm, sheet thickness steel (max.): 12 mm, CNC plasma cutting system BACH ThermoCut 2000 with pipe cutting device, TEKA dust extraction system, and plasma source. Manufacturer: BACH Maschinenfabrik GmbH Type: ThermoCut 2000 Year of construction: 2010 For sale is a used CNC plasma cutting system BACH ThermoCut 2000, including pipe cutting device, plasma source, dust extraction system, and complete piping. The system was used in our machine manufacturing company until recently and is suitable for cutting sheet metal as well as processing pipes. Technical data: Working area: 4,000 x 2,000 mm Plasma source: Thermal Dynamics Ultra-Cut 100 CNC control: myBach Pipe cutting device included Pipe diameter: min. 50 mm max. 320 mm Max. cutting thickness: Mild steel: up to 12 mm Stainless steel: up to 10 mm TEKA filter and dust extraction system included Complete dust extraction piping system included CE marking available Maintenance and condition The system was regularly maintained during its entire service life. Official maintenance by the manufacturer was last performed on August 20, 2013. After that, ongoing maintenance was carried out in-house. Filters of the TEKA dust extraction system were renewed approximately 6 months ago. Cutting torch head was renewed approximately 4 years ago. Cooling water filter is changed regularly, approximately once a year. The operating hour counter of the dust extraction system currently shows approximately 7,700 hours. Since the system was operated exclusively with the dust extraction system running, this value can be used as a good indication of the total operating time of the system. Known defect The system is currently not operational. After consultation with Voortman and Mr. Sobiech from Magma Industries, the cause is likely to be in the cooling circuit of the plasma source. According to the experts, the most likely causes of the fault are: Defective cooling water pump Defective flow sensor Leakage on the suction side of the cooling water system Djdpjzizkyofx Acyowd A final fault diagnosis has not yet been carried out. Spare parts for the installed Thermal-Dynamics plasma source are now only available to a limited extent. The machine is therefore explicitly sold as a system requiring repair or for refurbishment. Scope of delivery BACH ThermoCut 2000 CNC system Thermal Dynamics Ultra-Cut 100 plasma source Pipe cutting device TEKA filter and dust extraction system Control panel with controller Dust extraction piping Accessories according to existing equipment Special features ✅ Pipe cutting up to Ø 320 mm ✅ Complete package including dust extraction ✅ Solid industrial machine made in Germany ✅ Easy-to-disassemble gantry design ✅ Also interesting for buyers who already have a suitable plasma source Location 24161 Altenholz, Germany Price Negotiable €21,900 Inspection possible by appointment. Sale exclusively to commercial businesses, excluding any warranty for defects. Loading / Dismantling The system is offered exclusively for self-dismantling and self-collection. The buyer assumes full responsibility for the dismantling, loading, and removal of the machine at their own cost and risk. To assist with loading, a hall crane with a maximum lifting capacity of 10 tons is available on site. Use of the crane can be arranged in advance. Due to the size and weight of the system, we recommend an inspection before submitting an offer.

Condition: used, Year of construction: 2012, functionality: fully functional, power: 15 kW (20.39 HP), cutting height (max.): 200 mm, cutting width (max.): 1,300 mm, saw blade diameter: 600 mm, height adjustment type: pneumatic, saw blade bore: 80 mm, actuation type: electric, total length: 10,000 mm, total width: 2,200 mm, total height: 1,850 mm, overall weight: 3,200 kg, table height: 900 mm, Equipment: CE marking, rotational speed infinitely variable, saw blade guard, Longitudinal circular saws – made in Germany! New price of the machine: CHF 110,000.00! Cutting length: 8,200 mm Cutting width: 1,300 mm Dwedpfsz A Tgdjx Acyod Saw motor: 15 kW Max. cutting height: 200 mm Saw blade diameter: 450-600 mm Saw feed: Infinitely variable, from 0-80 m/min. Compressed air connection: 1/2”, 6 bar Required air volume: approx. 3500 m³/h

Condition: excellent (used), Year of construction: 2021, operating hours: 2,500 h, functionality: fully functional, overall weight: 1,100 kg, rotor diameter: 700 mm, type of input current: three-phase, input voltage: 400 V, rotational speed (max.): 3,400 rpm, power: 90 kW (122.37 HP), Equipment: rotational speed infinitely variable, This shredding machine is exceptional and highly innovative. The material to be processed is reduced to particles in 6 rows of small chambers, particle by particle, while simultaneously the particles are propelled against the grinding surface. The combination of these two effects results in a very fine grain size, and it is possible to dry the material during the shredding process. Keywords: turbo mill, impact mill, eddy current mill. Depending on the material, the machine can reduce the particle size to between 1000 µm and 5 µm. The throughput rate is between 100 and 900 kg/h, depending on the material. Dwodpfx Aszl Shzjcyjd The possible applications range from minerals, industrial products, powder coatings, chemicals, and dyes to food and feed products. The innovations of the machine are: • the plug-in connections of the wear tools (always in the same position with minimal tolerances) • rotation in both directions – this ensures that the tools wear evenly on both sides • conical design – allows the cutting gap to be adjusted precisely to 0.1 mm with only 12 screws. Technical data: • Drive power 90 kW – frequency converter (FU) is essential – frame size 90 kW with 150% overload for 60 seconds. • Speed up to 125 m/s • Tools: rotor and stator made of hard metal, available in different degrees of hardness; ceramic is also possible. • Machine monitoring via bearing temperature measurement and vibration measurement included. • Control cabinet is not included.

Year of construction: 2010, condition: used, CNC control system FIDIA with handwheel; travel ranges: X-axis approx. 11,500 mm, Y-axis approx. 1,550 mm, Z-axis approx. 2,250 mm; clamping table, length x width x height, 2 pieces, each approx. 2,000 x 2,000 mm; table load max. 1,000 kg; milling spindle, spindle power S1 / S6 approx. 7.4 kW / 12 kW, spindle speed 16,000 rpm, tool holder HSK 50A, B- and C-axis +/- 210° / +/- 104°, feed rate X-, Y-, Z-axis up to 16 m/min, axis acceleration m/s², machine footprint approx. 14,000 x 2,600 x 3,650 mm, with self-built table, total weight approx. 13,500 kg; NOTE: Fully functional condition, machine has already been disassembled and stored. The machine is already located at a different location in Kartonstraße 2, D-88255 Baienfurt. Free loading FCA D-88255 Baienfurt. Dwjdj Af Nl Uspfx Acyed

Condition: excellent (used), Year of construction: 2023, operating hours: 2,500 h, functionality: fully functional, machine/vehicle number: 4110, travel distance X-axis: 4,500 mm, travel distance Y-axis: 1,400 mm, overall weight: 11,000 kg, spindle speed (max.): 4,000 rpm, coolant supply: 7 bar, spindle motor power: 13 W, number of spindles: 1, number of slots in tool magazine: 14, input voltage: 400 V, type of input current: three-phase, Equipment: chip conveyor, documentation/manual, CMA GRD 4514 The CMA CNC machining center GRD 4514 offers a highly efficient solution for flexible drilling, threading, and milling operations in an extended format. Equipped with a 13.1 kW motor and a spindle speed of 50 to 4000 rpm, the system enables effortless drilling of holes up to 36 mm, as well as the cutting of threads up to M24 (based on ST 40 and HSS-Co cutting insert drills). - Extended work area and travel ranges: Table dimensions: 4500 x 1330 mm (effective machining length X-axis: 4500 mm) - Travel ranges X/Y/Z: 4500 x 1450 x 500 mm - Chip conveyor: Directly integrated into the machine table for optimal chip removal Productivity through pendulum operation: Thanks to the generous X-axis travel of 4500 mm, this variant is ideally suited for efficient pendulum operation. You can safely load and unload workpieces on one half of the table while the machine produces uninterruptedly on the other half. Protection is provided on the front side by a dynamically moving laser area sensor on the machine head. Software & Intelligent Control: Dodpozuw Eqofx Acyswd Graphical programming: Including automatic determination of cutting data and nesting of multiple products, even different ones, on the large table. Collision warning: Integrated protection for maximum process safety. Height correction: automatic measurement and correction of the workpiece height for 100% precise countersinking and reaming. CAD/CAM extension: Optionally, a conversion of 2D/3D drawings directly into DIN/ISO machine programs is possible. Standard equipment of the complete system: - Automatic tool changer for 14 tools - Automatic tool length measurement - Fixed light curtain in the Y-direction (500 mm above the table) and rear protective fence - Powerful coolant system with emulsion - Ethernet connection for fast remote service

Condition: new, Year of construction: 2026, Blasting trolley 5t battery-powered for blasting system - Load capacity: 5t Dedpjyyxidofx Acyswd - For rail installation - Battery drive - Remote control - Size: Length = 3000 mm, Width = 1000 mm - Surfaces for workpiece fixture mounts

Year of construction: 2014, condition: good (used), Technical Data – Condenser Maximum volume flow rate: 300 m³/h Maximum condenser dimensions in delivered condition: approximately 430 mm x 1610 mm high, cylindrical part: approximately Ø 273 mm Weight of the chamber in delivered condition: approximately 80 kg Capacity of the upper part (condenser): approximately 30 L Capacity of the lower part (collection container): approximately 28 L Material of elastomers: NBR/FKM/PTFE Maximum condenser temperature: 1 to 80 °C Maximum condenser vacuum: 0 to 1000 mbar (absolute) (Condenser not suitable for overpressure!!) Maximum heat exchanger temperature: 1 to 80 °C Heat exchanger working fluid: water Maximum water pressure in heat exchanger: 10 bar Dwjdpfecpwhbox Acysd Material of heat exchanger: tin-plated copper Material of condenser: stainless steel For technical questions or other sizes, please inquire.

Year of construction: 2018, condition: used, functionality: fully functional, machine/vehicle number: Gießbank 532 MAP40, General Data: - Designed for wall-mounted toilets - Low-pressure casting process with level control - Suitable for multi-part plaster molds - 40 mold stations per unit - A total of 160 mold stations - Mold spacing: 700 mm - Modular operation in units of 10 molds each - Operation with 10, 20, 30, or 40 molds in use per unit is possible - Different casting times per 10-mold section are possible Production Capacity - For currently manufactured "married" toilet models: the upper and lower parts are cast separately -> Two castings result in a complete toilet. 160 castings per casting cycle -> 80 complete toilets per casting cycle. - For models without "marriage": one mold station corresponds to one product -> up to 160 pieces per casting cycle. - Dimensions: Installation area approximately length: 33,800 mm, width: 4,100 mm, height: 4,300 mm. Single-row roller conveyor with a length of approximately 33,000 mm. Four lifting beam systems per unit. Each lifting beam is designed for 10 molds. One extraction trolley per unit. - Casting and slip system: Slip supply DN 100, slip return DN 100, compressed air connection 2 inches for the pressure line, filling via high-level or level tanks, two level tanks per unit, two casting lines per level tank, return of excess slip to the return slip tank, flushing of the slip lines with water and compressed air, four separate flushing systems per unit. - Mold mounting and clamping technology: Steel base frame, four lifting beams with electromechanical cable winch drive, cable breakage and cable slack protection, divisible vertical clamping devices, upper clamping beams with quick-release fasteners, pneumatic clamping hoses. - Demolding and handling: Pneumatic extraction assistance, molds can be clamped and tilted by 90 degrees, mold halves are manually separated, ergonomic transfer of the green part to a roller conveyor, two-hand safety control, quick-change system for different mold mountings, track for existing vacuum lifting system. - Compressed air and low-pressure system: Separate compressed air distribution for each 10 molds, three compressed air circuits (upper clamping beams and core boxes, vertical clamping devices, separation of the green part and mold), individual pressure control via pressure regulators, pressure monitoring of the clamping circuits, acoustic signal in case of insufficient clamping pressure, low-pressure system for stabilizing the green part in the mold and for hose drying after flushing. Dsdpfx Acjz Agw Eeyjwd - Drying, ventilation, and lighting: Fans for drying the parts, diameter approximately 950 mm, LED lighting strips along the unit, active unit sections can be visually marked by the lighting, uniform drying of the plaster molds supports up to two casting cycles per day. - Electrical system and control: Two main switch cabinets, one main switch cabinet controls 20 molds and two lifting beams each, two-hand operation for safety-relevant movements, separate control cabinets on the level tanks and lifting beams. - Advantages: High production flexibility due to the 10-mold division, different products or casting times within one unit are possible, unused conversion components remain on the unit, suitable for different toilet models and production concepts, modular design facilitates partial occupancy and adjusted production quantities, extensive peripherals for casting, flushing, drying, demolding, and transport are available.

Year of construction: 2018, condition: used, functionality: fully functional, machine/vehicle number: Gießbank 533 MAP40, General Data: - Designed for wall-mounted toilets - Low-pressure casting process with level control - Suitable for multi-part plaster molds - 40 mold stations per unit - A total of 160 mold stations - Mold spacing: 700 mm - Modular operation in units of 10 molds each - Operation with 10, 20, 30, or 40 molds in use per unit is possible - Different casting times per 10-mold section are possible Production Capacity - For currently manufactured "married" toilet models: the upper and lower parts are cast separately -> Two castings result in a complete toilet. 160 castings per casting cycle -> 80 complete toilets per casting cycle. Djdpfsz Ag Rrox Acyewd - For models without "marriage": one mold station corresponds to one product -> up to 160 pieces per casting cycle. - Dimensions: Installation area approximately length: 33,800 mm, width: 4,100 mm, height: 4,300 mm. Single-row roller conveyor with a length of approximately 33,000 mm. Four lifting beam systems per unit. Each lifting beam is designed for 10 molds. One extraction trolley per unit. - Casting and slip system: Slip supply DN 100, slip return DN 100, compressed air connection 2 inches for the pressure line, filling via high-level or level tanks, two level tanks per unit, two casting lines per level tank, return of excess slip to the return slip tank, flushing of the slip lines with water and compressed air, four separate flushing systems per unit. - Mold mounting and clamping technology: Steel base frame, four lifting beams with electromechanical cable winch drive, cable breakage and cable slack protection, divisible vertical clamping devices, upper clamping beams with quick-release fasteners, pneumatic clamping hoses. - Demolding and handling: Pneumatic extraction assistance, molds can be clamped and tilted by 90 degrees, mold halves are manually separated, ergonomic transfer of the green part to a roller conveyor, two-hand safety control, quick-change system for different mold mountings, track for existing vacuum lifting system. - Compressed air and low-pressure system: Separate compressed air distribution for each 10 molds, three compressed air circuits (upper clamping beams and core boxes, vertical clamping devices, separation of the green part and mold), individual pressure control via pressure regulators, pressure monitoring of the clamping circuits, acoustic signal in case of insufficient clamping pressure, low-pressure system for stabilizing the green part in the mold and for hose drying after flushing. - Drying, ventilation, and lighting: Fans for drying the parts, diameter approximately 950 mm, LED lighting strips along the unit, active unit sections can be visually marked by the lighting, uniform drying of the plaster molds supports up to two casting cycles per day. - Electrical system and control: Two main switch cabinets, one main switch cabinet controls 20 molds and two lifting beams each, two-hand operation for safety-relevant movements, separate control cabinets on the level tanks and lifting beams. - Advantages: High production flexibility due to the 10-mold division, different products or casting times within one unit are possible, unused conversion components remain on the unit, suitable for different toilet models and production concepts, modular design facilitates partial occupancy and adjusted production quantities, extensive peripherals for casting, flushing, drying, demolding, and transport are available.

Year of construction: 2018, condition: used, functionality: fully functional, machine/vehicle number: Gießbank 531 MAP40, General Data: - Designed for wall-mounted toilets - Low-pressure casting process with level control - Suitable for multi-part plaster molds - 40 mold stations per unit - A total of 160 mold stations - Mold spacing: 700 mm - Modular operation in units of 10 molds each - Operation with 10, 20, 30, or 40 molds in use per unit is possible - Different casting times per 10-mold section are possible Production Capacity - For currently manufactured "married" toilet models: the upper and lower parts are cast separately -> Two castings result in a complete toilet. 160 castings per casting cycle -> 80 complete toilets per casting cycle. - For models without "marriage": one mold station corresponds to one product -> up to 160 pieces per casting cycle. - Dimensions: Installation area approximately length: 33,800 mm, width: 4,100 mm, height: 4,300 mm. Single-row roller conveyor with a length of approximately 33,000 mm. Four lifting beam systems per unit. Each lifting beam is designed for 10 molds. One extraction trolley per unit. - Casting and slip system: Slip supply DN 100, slip return DN 100, compressed air connection 2 inches for the pressure line, filling via high-level or level tanks, two level tanks per unit, two casting lines per level tank, return of excess slip to the return slip tank, flushing of the slip lines with water and compressed air, four separate flushing systems per unit. - Mold mounting and clamping technology: Steel base frame, four lifting beams with electromechanical cable winch drive, cable breakage and cable slack protection, divisible vertical clamping devices, upper clamping beams with quick-release fasteners, pneumatic clamping hoses. - Demolding and handling: Pneumatic extraction assistance, molds can be clamped and tilted by 90 degrees, mold halves are manually separated, ergonomic transfer of the green part to a roller conveyor, two-hand safety control, quick-change system for different mold mountings, track for existing vacuum lifting system. - Compressed air and low-pressure system: Separate compressed air distribution for each 10 molds, three compressed air circuits (upper clamping beams and core boxes, vertical clamping devices, separation of the green part and mold), individual pressure control via pressure regulators, pressure monitoring of the clamping circuits, acoustic signal in case of insufficient clamping pressure, low-pressure system for stabilizing the green part in the mold and for hose drying after flushing. Dwodpfx Acjz Agv Ueyjd - Drying, ventilation, and lighting: Fans for drying the parts, diameter approximately 950 mm, LED lighting strips along the unit, active unit sections can be visually marked by the lighting, uniform drying of the plaster molds supports up to two casting cycles per day. - Electrical system and control: Two main switch cabinets, one main switch cabinet controls 20 molds and two lifting beams each, two-hand operation for safety-relevant movements, separate control cabinets on the level tanks and lifting beams. - Advantages: High production flexibility due to the 10-mold division, different products or casting times within one unit are possible, unused conversion components remain on the unit, suitable for different toilet models and production concepts, modular design facilitates partial occupancy and adjusted production quantities, extensive peripherals for casting, flushing, drying, demolding, and transport are available.

Condition: good (used), Year of construction: 2020, functionality: fully functional, total length: 2,000 mm, total width: 1,100 mm, total height: 2,150 mm, overall weight: 122 kg, Glass transport frame Dimensions: 2000x1100x2150 mm (LxWxH) Dodpe Ahgwxofx Acyjwd Maximum load capacity: 1,500 kg Loading height: 2,000 mm 4 units available.

Year of construction: 2019, operating hours: 3,000 h, condition: excellent (used), functionality: fully functional, machine/vehicle number: 10031325, This is a high-resolution NIR system capable of detecting particles in the 3 mm size range. Additionally, the machine is equipped with an electromagnetic detector that has a sensitivity of approximately 1.5 to 1 mm, depending on the metal type. Dsdpfxjzl Uzwe Acyowd Depending on the settings, it can sort positively or negatively. Technical data: Belt width: 1024 mm Nozzle bar: 6.4 mm working width Upon request, complete documentation can be provided. The machine was in operation at an R&D center in Israel. Since the company now operates a production facility in Europe, the R&D center will be closed. The machines will be transported to Europe at the owner's expense and can be delivered EXW at a port or at the production facility in Europe. The details for optimal transport need to be clarified. The machine price does not include packaging on a pallet.

Condition: used, Year of construction: 2019, machine/vehicle number: S4-3044, input voltage: 230 V, type of input current: AC, laser power: 120 W, type of cooling: air, total width: 1,428 mm, total height: 1,050 mm, total length: 952 mm, overall weight: 300 kg, laser wavelength: 10,600 nm, input frequency: 50 Hz, For sale is a used, professional Trotec Speedy 400 CO₂ laser engraving and cutting machine, manufactured in May 2019. The machine is in used condition, commensurate with its age and previous use. Technical data: Manufacturer: Trotec Laser GmbH, Austria Model: Speedy 400 Year of manufacture: May 2019 Serial number: S4-3044 Laser type: CO₂ laser Maximum laser power according to the nameplate: 120 W Working area, typical for the model: approx. 1,016 × 610 mm Power connection: 230 V / 50–60 Hz Rated power consumption: 1.9 kW Known operating condition: The machine could be switched on and operated via the integrated control panel. The following functions could be checked: The X and Y axes of the laser head can be moved via the control panel. The height-adjustable work table can be moved via the control panel. The axes and the table could be moved to various positions. Djde Adrb Nopfx Acyjwd The red pilot/positioning laser is visible. The operating and control indicators are active. Important note regarding the laser: The actual condition of the CO₂ laser source is unknown. The operating hours and the remaining available laser power are unknown. A complete engraving or cutting test has not been performed. Scope of supply: The offer includes the Trotec Speedy 400 shown in the pictures, with the existing work table, laser head, and control panel. A separate extraction system, a control PC, and software licenses are not included in the offer.

Year of construction: 2021, condition: like new (used), functionality: fully functional, Component 1: ATM-800 P Tangential Dereeler (2 pieces) Heavy-duty dereeler for controlled unwinding of copper wire coils. • Max. coil diameter: 800 mm • Max. coil width: 300 mm • Pickup hole: Ø52 / Ø56 mm • Max. coil weight: 300 kg • Braking force: 100 - 2000 N • Brake torque: 3 - 800 Nm Dwsdpfx Aoz Ap R Iscyjd • Max. speed: approx. 5 rpm • PLC control with torque sensor Component 2: HBK-40-S Automatic Taping Machine Professional automatic taping machine for coil and conductor insulation. • Servo-controlled taping head • Operator terminal and display • Integrated X-axis guidance • Electric hysteresis brake • Automatic overlap control via encoder • Suitable for various insulation materials

Year of construction: 2020, operating hours: 1,000 h, condition: like new (used), functionality: fully functional, machine/vehicle number: 19/00XXX, Probat G45 Retro / Kirsch & Mausser Professional Coffee Roasting System – Complete System (As New, 1,000 Hours) Price: EUR 100,000 net plus VAT Condition & History: • Operating hours: approx. 1,000 hours (as new, well-maintained, in excellent condition). • Design: G45 Retro system, newly built by Kirsch & Mausser in 2019/2020, featuring a cast-iron design and complete modern peripherals. • Availability: Ready for immediate pickup. Equipment (6 items included): Item 1: Probat G45 Retro Roasting Machine • Batch size: 25 - 55 kg • Gas type: Natural gas or propane (230/400 V, 50 Hz) • Separate drives for roasting drum, agitator in the cooler, and cooling fan (simultaneous roasting and cooling possible). • Enclosed housing with large maintenance openings, manual handwheel for airflow regulation (drum interior/jacket, aroma, external). • Cooling sieve with a second outlet, roasting fans directly on the machine, large cyclone with chaff collection container, and connection for manual fire extinguishing water supply. • Atmospheric burner with increased output (145 kW), continuously adjustable via potentiometer on the control panel, including all safety and monitoring devices (solenoid valves, flame and gas pressure monitoring, pressure regulator). • Complete thermocouple equipment (production, roasting air, roasting exhaust air, hot air supply in the rear wall) with separate connections for temperature recording systems (e.g., Cropster). • Manual control on the control panel with digital display for temperatures and roasting times, as well as a frequency inverter for the roasting fan. Item 2: Frequency Inverter for Drum Operation • Continuous adjustment of the roasting drum speed (manually or via recipe). • Individual speed monitors and live display on the touch panel. Item 3: Semi-Automatic Control with Touch Panel • Freely positionable control panel with touch panel. • Readability and automatic regulation of intake air temperature and roasting fan output via recipes. • Parameter changes during the roasting process can be made at any time. • Additional potentiometers for independent control of the burner, roasting fan, and cooling fan. • Pneumatic actuation of the green coffee feed and the outlet valve in the drum lid. Item 4: Green Coffee Transport • Hopper for up to 60 kg of green coffee. • Conveyor fan, conveyor pipe with bends and clamps, and enclosed machine hopper. Dwodpfx Aoz Eah Hocyod Item 5: High-Suction Destoner • Hopper at the cooling sieve outlet, riser pipe with sight glass. • Collection container with impact plate to prevent coffee breakage, connection to the cooling fan. • Air intake flap for regulating the rising speed, slide valve at the outlet. • Frequency inverter for the destoner fan with potentiometer on the frame. Item 6: Drum Vacuum Measurement • Pressure sensor in the pipe between the roaster and the system with direct display on the touch panel. Terms & Conditions: • Location: Luxembourg. • Communication: Please submit inquiries exclusively in writing via the platform/email. No telephone contact. • Legal: Commercial B2B sale excluding any warranty, liability for defects, and right of withdrawal. The system is sold in its current "as is" condition. Dismantling and transport are the responsibility of the buyer.

Year of construction: 2013, condition: used, Decanter centrifuge for thickening municipal, industrial and biological sludge Additional title: Sludge dewatering system Throughput capacity: 15000 l/h Weight: 545 kg Position: To be mounted on the customer's substructure Features: Operating platform Dwjdpfx Ace Ahhfieysd

Condition: used, Year of construction: 2016, functionality: fully functional, Conveyor line/roller conveyor system, conveyor technology approx. 50 meters Manufacturer: RBS-Förderanlagen GmbH Model: Conveyor line Condition: Used Year of manufacture: 2016 The system consists of: 1 x Inclined belt conveyor, approx. 3.2 meters long 2 x Pneumatic lifts 3 x 90° bends 2 x Folding elements / passage elements 1 x Control cabinet 25 pieces of height-adjustable feet and the remaining conveyor belt/roller conveyor approx. 34 meters Total length: approx. 50,000 mm Total width: 750 mm Conveyor width: approx. 680 mm Roller diameter: 50 mm Dwodo Aicytjpfx Acyod Internal article number: 2025120101 Features: Condition: fully functional, with signs of wear Ideal for fast material transport Professionally dismantled and packaged Collection address: Industriestraße 5 (47918 Tönisvorst) The conveyor technology was operational until it was dismantled. Due to the excellent workmanship of the conveyor technology, your material glides gently to its destination, even under high load. Custom-made solutions for your in-house logistics For roller conveyors, belt conveyors, inclined conveyors, or telescopic conveyors for loading and unloading your goods, we are your competent partner! We will gladly prepare an individual offer for you or advise you on the design or assembly. Simply let us know your requirements and the local conditions.

Condition: used, Year of construction: 2021, functionality: fully functional, machine/vehicle number: 1605269/1, total width: 630 mm, total height: 1,115 mm, total length: 1,010 mm, working width: 460 mm, input voltage: 400 V, type of input current: AC, overall weight: 200 kg, power: 0.37 kW (0.50 HP), roller diameter: 100 mm, passage height: 80 mm, feed rate X-axis: 35 m/min, height adjustment type: mechanical, tank capacity: 2 l, roll width: 450 mm, input frequency: 50 Hz, workpiece height (max.): 80 mm, Equipment: double-sided, For sale is a well-maintained glue and roller application machine from Axel Wirth Maschinen GmbH, type LW 100/450. The machine was manufactured in 2021, has comparatively few operating hours, and is in technically perfect and well-maintained condition. A particular advantage is the adjustable working speed or feed rate (6 - 35 m/min). This allows the machine to be flexibly adapted to different workpieces, materials, and application media. The machine is mounted on a sturdy, mobile base with lockable wheels. As a result, it can be easily moved within the production area and safely positioned at the respective location. A total of two identical machines are available. The stated price applies per machine. An attractive package price is possible if both machines are purchased. Djdezr H Aaepfx Acyewd The LW 100/450 is suitable for the uniform application of liquid and pasty media onto flat or textured workpieces, for example: - Glue and adhesive - Oil and wax - Stain and primer - Paints and dispersions - Resins and comparable application media Among other materials, wood, solid wood, parquet flooring, chipboard, cork, cardboard, metal, stone, rubber, and insulation materials can be processed. The application quantity can be adjusted via the lateral adjustment devices. The rollers and glue trays can be removed with a few simple steps, making the machine easy to clean. Technical data and equipment Manufacturer: Axel Wirth Maschinen GmbH Type: LW 100/450 Year of manufacture: 2021 Nominal width: 450 mm Working width: approx. 460 mm Passage height: approx. 80 mm Diameter of the application rollers: 100 mm Capacity per glue container: approx. 2.3 liters Drive power: 0.37 kW Adjustable working speed or feed rate Application rollers above and below Separate control cabinet Main switch and emergency stop Mobile base with lockable wheels CE marking Condition: used, well-maintained, and technically perfect Operating hours: comparatively low Inspection and test run are possible after prior appointment. Collection at the Leun location. Shipping by freight forwarder can be organized if required, upon agreement. If you have any questions or are interested, please do not hesitate to contact us. We will be happy to provide further information and photos. Price: €5,900 (negotiable) per machine plus VAT (can be shown). Package price for both machines: on request All information is provided to the best of our knowledge. The sale takes place under the conditions applicable to the seller for used machines.

Year of construction: 2025, condition: as good as new (ex-display), functionality: fully functional, machine/vehicle number: R500, FiberFlow R500 Cooling Die for Sale The FiberFlow R500 Cooling Die is a specially developed solution for structuring alternative proteins in High Moisture Extrusion (HME). The cooling die is designed to produce fibrous protein structures through controlled cooling and optimized flow guidance, making it particularly suitable for applications such as plant-based meat and seafood alternatives, as well as structured convenience products. The FiberFlow R500 is designed for throughput rates of up to 500 kg/h at operating pressures of up to 70 bar. Its annular (ring-shaped) geometry ensures optimal flow distribution, resulting in uniform fiber formation and consistently high product quality. The system features a modular design and is sold as a complete unit consisting of four segments. Dodpfxoy Um Tgo Acyewd Particular emphasis has been placed on hygienic design, enabling the system to meet the stringent requirements of the food industry. The construction allows for easy and efficient cleaning. The FiberFlow R500 is designed for seamless integration into existing extrusion lines and can be incorporated into continuous production processes without difficulty.

Condition: excellent (used), Year of construction: 2017, functionality: fully functional, machine/vehicle number: 2080403, CNC Horizontal 5-Axis Double-Spindle Machining Center Manufacturer: SW – Schwäbische Werkzeugmaschinen GmbH Type: BAW06-22 Year of Manufacture: 2017 Machine Number: 2080403 Control System: CNC Siemens 840 Number of Axes: 5 Number of Spindles: 2 Double Table System Dedpfx Acj Aarqpsyewd Travel Ranges X/Y/Z: 600 / 600 / 510 mm Spindle Speed: up to 17,500 rpm Rapid Traverse: up to 45 m/min Tool Interface: HSK-A63 Machine Weight: approx. 16,000 kg Equipment: Standard accessories Powerful CNC horizontal machining center with a double spindle and double table system for precise and efficient series production. Location: Maribor, Slovenia Availability: By arrangement Inspection possible by appointment.

Condition: good (used), Year of construction: 2013, input voltage: 400 V, input frequency: 50 Hz, Equipment: documentation/manual, Exo-Zell-EROWA automation with EDM314MF30+HSC600/5 Automation kit EROWA UPC table clamping system with adapter plate ITS/Powerchuck 10 pallet changing stations 150 electrode changing stations JMS-Certa identification Measuring machine DuraMAX EDM314MF30, year of manufacture 2013 Technical data: Travel ranges XxYxZ 905x705x455mm Workpiece table: 1150x850mm Dsdpfx Aoz Sp Hascyswd Tank size 1200x900mm Filling height of the work tank 500mm Distance table/electrode holder 250/700mm Workpiece weight max. 3000kg Dimensions WxDxH 2090x3416x3100mm Machine weight 7500kg Operating hours 10,000h Control interface MF30 Backflushing filter with dirt container Integrated cooling unit Automatic tank refill Extinguishing system Co² Smoke extraction Fire protection flap Erosion generator exopuls+60A C-axis 100°/min with holding brake, direct measurement Direct measuring system in all axes HSC600/5, 5-axis, year of manufacture 2008 Control iTNC530i Milling spindle HVC140, 42000rpm Technical data: Travel range XxYxZ 650x550x400mm Travel range BxC B105+/- C endless Table diameter 410mm Distance table/spindle nose 600mm Workpiece weight max. 200kg Rapid traverse 50m/min Rotational speed B/C 80/80°/min HSK40-E 60-position tool changer Oil mist extraction Minimum quantity lubrication Manual control panel with handwheel Adjustable air/cooling supply Kinematics optimization Calibration sphere for kinematics optimization Length compensation for all axes HIB cooling unit Measuring probe Renisaw OMP400 Calibration ring Performance acceptance test Transport Commissioning on site Training

Condition: used, functionality: fully functional, machine/vehicle number: 4937, Josef Emmerich ER511VGL Pump Set – Complete Unit on Frame – Industrial Design For sale: a robust industrial pump set from Josef Emmerich Pumpenfabrik GmbH, mounted on a steel frame with an electric motor, buffer tank, control cabinet, and piping. Suitable for various applications in water treatment, the process industry, wastewater technology, and industrial installations. Dwodpfxj Ah Dyne Acysd The unit is designed as a complete system and can be used for pumping water, sludge-containing liquids, and other process media, depending on the application. The pump is equipped with an electric motor and pressure tank, enabling reliable and stable operation. Technical specifications: Manufacturer: Josef Emmerich Pumpenfabrik GmbH Type: ER511VGL Pump number: 4937 CE-marked Drive: Electric motor Design: Complete pump set on frame Includes: Electric motor Pump Pressure/buffer tank Control cabinet Piping and connections Applications: Water treatment Wastewater treatment plants Process water transport Industrial pump installations Recycling and environmental technology Production processes Special features: Durable industrial design Compact setup on frame Suitable for continuous operation Supplied complete, as shown Easy to integrate into existing installations