Used Cold Rolling Machine for sale (69,575)

Condition: used, Thread Rolling Machine, Cold Rolling Machine, Thread Rolling Machine, Profile Rolling Machine Manufacturer: PEE-WEE Model: UPW 24 Serial No.: P07 Year of manufacture: 2007 Maximum rolling force: 24 tons Maximum tool diameter: 270 mm Roll spindle diameter: 69.85 mm Tool bore diameter: 70 mm (nominal diameter) Maximum tool/reception length: 180 mm Maximum workpiece diameter: 50 mm Hydraulic motor power: 3 kW Roll drive motor power: approx. 5.5 kW Electrical connection: 400 Volt, 50 Hz, 10 kW - Pivotable roll spindle for through-feed thread rolling - Roll spindle speed adjustable in 4 steps via gearbox shift - Hydraulic unit integrated in the machine base - Operating manual with electrical schematic Godeuz If Nopfx Aivjkc Space requirements (L x W x H): 2,000 x 1,450 x 1,900 mm Weight: approx. 3 tons Very good condition Plunge Rolling: The thread rolling tools, having the same pitch as the workpiece, form the thread by penetrating the workpiece up to the nominal diameter. The maximum thread length is limited to the width of the rolling dies. Through-feed Rolling: Used when the thread length is greater than the width of the rolling dies. Through-feed tools are divided into three sections – entry, calibration, and exit. Knurling rolls have no pitch and are swiveled at the lead angle corresponding to that of the profile to be rolled. Lead angle rolls differ from knurling rolls by having a pitch in the profile. The sum of the lead angle and swivel angle results in the effective lead angle in the workpiece.

Condition: used, Year of construction: 2015, overall weight: 16,000 kg, total height: 2,200 mm, total length: 4,410 mm, total width: 2,600 mm, GROB C6-A – Cold Rolling Machine Technical Data: Gear Module: up to approx. 2.3 Gear Diameter: approx. 8–80 mm Max. Clamping Diameter: approx. 315 mm Power: 25 kW Godpfx Aez E Ra Hjivokc Weight approx.: 16,000 kg Dimensions (LxWxH) approx.: 4410 x 2600 x 2200 mm Year of construction: 2,015 Terms of payment: 100% prepayment before pick-up Terms of delivery: From foundation under power: No

Condition: used, Thread rolling machine, cold rolling machine, thread forming machine, profile rolling machine Manufacturer PEE-WEE, Type P 24 Q Serial No. LC2403099, Year of manufacture 2004 Rolling force, max. 24 tons Tool diameter, max. 200 mm Rolling spindle diameter 69.85 mm Tool bore diameter 70 mm (nominal diameter) Receiving length, tool length, max. 180 mm Workpiece diameter, max. 50 mm Rolling spindle speed 22 - 44 - 95 - 190 RPM Hydraulic motor power approx. 3 kW Rolling drive motor power 5.5 kW Mains connection 400 Volt, 50 Hz - Swiveling rolling spindle for thread through-rolling - Rolling spindle speed in 4 stages via gear change - Hydraulic system integrated in the machine bed Space requirement L x W x H 2000 x 1750 x 2550 mm Weight approx. 3 tons Good condition Plunge rollers: The thread rolling tools with the same pitch as the workpiece form the thread by penetrating the workpiece up to the nominal diameter. The thread length is a maximum as long as the rolling tools are wide. Gkedpfx Aeh A S Htjivsc Through-rolling tools: If the thread length is greater than the rolling tool width. Through-rolling tools have 3 sections - the inlet, the calibrating section, and the outlet. Grooved rollers have no pitch and are swiveled with the helix angle of the profile to be rolled. Helix rollers differ from grooved rollers by having a pitch in the profile. The sum of the helix angle and the swivel angle results in the helix angle in the workpiece.

Year of construction: 1998, condition: excellent (used), machine/vehicle number: ExCello Serial Number 3888, MICHIGAN Rotoflo Type 3237 Cold Forming Machine. Original Serial Number: 4590 ExCello Serial Number 3888 New 1975 rebuilt by ExCello late 1990’s Country of Origin: USA For the coldforming of profiles for serrations (straight or angular), spiral teeth, oil grooves, threads and knurls. Capacity: Gkedpefnk Ehsfx Aivec Maximum slide stroke 1065 mm Maximum rack length 915 mm Maximum profile diameter 50 mm Maximum profile length 125 mm Standard module range 0.3 to 1.25 Motor size 15 kW Hydraulic tank capacity 1000 l Overall floorspace width of machine 5014 mm Width of machine 2768 mm Depth with outboard support 4165 mm Height 2000 mm Approximate weight of machine 11,700 kgs Complete with: Hydraulically operated outer support assembly to accommodate part length universal headstock, Universal rack holding feature.

Condition: used, Year of construction: 2011, Control Siemens Sinumerik 840D sl centre height 1.150 mm z-axis 1.559 / 307 mm x-axis 16 - 80 mm Swing circle diameter 92 mm roll spindle turning speed range 0 - 3.000 U/min Rolling mill roll clearance - axial 0,025 mm feed speeds infinitely variable 0 - 30.000 mm/min rapid traverse 30.000 mm/min Swivel angle range ±3,2 ° Max. speed - main spindle 375 U/min Gksdpfx Aozdk Ikjivoc piston stroke 400 mm diameter of piston 90 mm with effective piston area 63,6 cm² In our assessment, the machine is in good used condition and can be inspected under power by appointment. Accessories, as well as the tools and clamping devices shown in the images, are included in the scope of delivery only if explicitly noted in the additional information. Subject to changes, errors in technical data and specifications, and prior sale!

Condition: used, functionality: fully functional, Year of construction: 2009, machine/vehicle number: 4ROLL DUAL PREPINCH, control type: manual, degree of automation: manual, actuation type: hydraulic, number of rollers: 4, roller (bottom) diameter: 470 mm, roller (top) diameter: 470 mm, side roll diameter: 430 mm, sheet thickness (max.): 40 mm, sheet thickness steel (max.): 40 mm, sheet thickness stainless steel (max.): 35 mm, sheet thickness aluminum (max.): 45 mm, sheet thickness brass (max.): 50 mm, overall weight: 35,000 kg, total length: 6,100 mm, total width: 2,225 mm, total height: 2,700 mm, input voltage: 400 V, input frequency: 50 Hz, number of digital displays: 7, Equipment: cone bending device, documentation/manual, emergency stop, hardened rollers, swiveling upper roller, PLATE BENDING MACHINE 4 ROLL HYDRAULIC 3000 X 40 MM brand OMCCA YEAR 2009 DOUBLE INITIAL PINCH Machine used in working condition Gksdoz Rw R Dopfx Aivoc Bending capacity -Plate width : 3000 mm -Rolling plate thickness 40 mm - Prebend thickness 30 mm Rolls dimensions: -Useful length 3050 mm -central rolls upper/lower D 470 mm -side rolls left/right D 430 mm One extra smaller upper roll D=350mm fast interchangeable • Hardening of the rolls high strength surface • All 4 rolls driven hydraulic powered rollers rotation • Conical bending attachment side rolls tiltable to form cones, contrast pad roller type. • Opening of top roll hydraulic drop-end to unload the plate being formed • Variable speed working roll bending rotation hydraulic speed fast/slow. • Console electric on wheels with centralized commands joysticks and digital readout 3 axis. • Digital readouts of the rolls position and top support • Power electric 50 Hp voltage 3-phase 400 /50 • Dimension 6100 x2225 x H 2700 mm - weight 35000kgs Additional tooling with the machine Top central support motorized to hold in place the formed plate up to diameter 3500 mm Side support hydraulic dual articulation

Condition: used, Thread rolling machine UPWS 25. Gedezd Rf Nepfx Aivjkc

Condition: used, Width: 60 cm Complete roll forming line equipped with tools for the production of a new type of industrial gutter for galvanized steel/stainless steel CE compliant Godpfx Aez R S T Uoivokc Uncoiler capacity: 2 metric tons Maximum width: 600 mm Coil inner and outer diameters: 508–920 mm Hydraulic claw extension: 460 > 640 mm 4 kW Roll Forming Line Type H 18 stations Maximum width: 600 mm Maximum thickness: 0.8 mm Shaft diameter: 60 mm Maximum center-to-center shaft distance: 300 mm Siemens Simatic touchscreen control + Ethernet connection 7.5 kW Hydraulic shear Force: 5 metric tons Condition: machine has seen very little use Online auction of metalworking machines, woodworking machines, overhead cranes, workshop equipment, and lumber inventory, including an AMADA Arcade 210 CNC punch and nibbler, MAZAK VTC-41L and MT-V-515 vertical CNC machining centers, MAZAK Super Turbo-X 48 Mk II CO₂ laser cutting machine, BYSTRONIC Byjet 4022 CNC waterjet cutting machine, TECNOMA profiling and roll forming machines, ELUMATEC and EMMEGI aluminum sawing machines, HACO ERMS 200-metric-ton CNC press brake, ADIRA CNC press brake, LEFORT C 265T hydraulic scrap baler/shear combination, ESAB Pegasus CNC plasma cutting machine, GEMA powder coating machine with drying oven and exhaust system, EURO-MAC punching and nibbling machine, various KONE and DEMAG overhead cranes, VECOPLAN industrial shredder, NEDERMANN filter unit, METORA band saw, various metalworking and woodworking machines, panel saws, edge banders, milling machines, drills, compressors, workbenches, teak beams, sawn logs, and various accessories, etc. The online auction opens Wednesday 14 October and closes Thursday 5 November. Register your account via our website and place your bid. For viewings and inspections check the auction information on the website. Viewing day is on: - Tuesday 3 November Pickup days are on: - Tuesday 10 November - Thursday 12 November Dome Auctions is an innovative auction platform dedicated exclusively to the industrial sector. By focusing on machinery sales from business closures, restructurings, and bankruptcies, we provide a trusted marketplace where buyers and sellers connect with confidence. Unlike general auction houses, Dome Auctions specializes in selling complete industrial assets directly from factories, ensuring quality and reliability. With a commitment to transparency, industry expertise, and tailored service, we streamline the sales process and maximize value for all parties. As online auctions continue to grow in the European industrial market, Dome Auctions offers a professional and efficient solution for companies seeking high-quality machinery at competitive prices.

Condition: used, Year of construction: 1997, functionality: unexamined, total height: 2,500 mm, total length: 33,223 mm, total width: 2,000 mm, table width: 700 mm, input frequency: 60 Hz, input voltage: 460 V, table length: 5,000 mm, table height: 1,200 mm, control cabinet width: 600 mm, control cabinet length: 1,500 mm, control cabinet height: 2,500 mm, compressed air connection: 5.5 bar, Stud & Track Rollforming Machine With 4.5 Tonnes Decoiler & Crane 5 Tonnes Capacity - Fully Dismantled - Ready to be transported MACHINE MANUFACTURER: BRADBURY UK GENERAL SPECIFICATIONS STUD LINE MATERIAL : GALVANIZED COLD ROLLED STEEL MATERIAL STRENGTH : 85.000 PSI MAX YIELD STRENGTH 55.000 PSI MIN· YIELD STRENGTH THICKNESS: 20 GA. TO 16 GA.-"HEAVY GAUGE" 22 GA. TO 25 GA.-"LIGHT GAUGE" ENTRY COIL WEIGHT: 10.000 LB MAX Gkedpfjxya Hzjx Aivsc ENTRY STRIP WIDTH: 12" MAX C APPROX. 5" MIN C APPROX. ENTRY COIL I .D: 20" MAX ENTRY COIL O.D: 72" MAX EFF. LINE SPEED : l20-150 FPM-"HEAVY GAUGE" 175-250 FPM-"LIGHT GAUGE" ROLLFORMER SPEED: 120-250 FPM PASS LINE HEIGHT: 51" LINE DIRECTION : RIGHT TO LEFT MODE OF OPERATION : PREPUNCH/POSTCUT CUT LENGTH : 20' MAX. 5· MIN GAUGE" : 90 % C APPROX. ) OF PRODUCT iON < i 6' LENGTH TOLERANCE : •/- 1/16" AT 250 FPM MAIN POWER : ELEC : 460 VOLTS 60 HERTZ 3 PHASE 192.2 FLA : AIR : 80 PSI MIN. CLEAN 6 DRY : HYO : 1500 PSI WORKING PRESSURE CONTROL : 115 VOLT AC AIR CONSUMPTION: 2 CFM MAX. AT 80 PSI

Condition: like new (used), functionality: fully functional, Year of construction: 2024, control type: CNC control, degree of automation: automatic, actuation type: hydraulic, controller manufacturer: EVO, controller model: EVO 4 AXIS 15", number of rollers: 4, roller (top) diameter: 300 mm, roller diameter: 300 mm, roller length: 3,100 mm, working width: 3,000 mm, working height: 1,250 mm, sheet thickness (max.): 22 mm, sheet thickness steel (max.): 22 mm, sheet thickness stainless steel (max.): 20 mm, sheet thickness aluminum (max.): 30 mm, overall weight: 17,000 kg, total length: 5,500 mm, total width: 2,000 mm, total height: 2,100 mm, power: 18.5 kW (25.15 HP), input voltage: 400 V, number of digital displays: 4, warranty duration: 12 months, Equipment: cone bending device, documentation/manual, emergency stop, hardened rollers, swiveling upper roller, 4roll hydraulic plate bending machine MODEL M3035 , year 2024 machine as new with warranty included Planetary dual pre-pinch plate prebend SPECIAL FRAME WITH TOP ROLL REDUCED SIZE 300 MM TO ACHIEVE SMALLER BENDING DIA 330 MM Performance Capacity: Plate width 3000 mm plate thickness rolling 22mm pre-bend 20 mm minimum rolling diameter ID 330 mm usefull surface width on the rollers 3100 mm Power electric motor 18.5kw on hydraulic unit Vac 400/50 -480/60 Installed configuration Hardened rolls high surface strength Conical plate rolling, cone bending Electric console remoted on wheels with joysticks and readout CNC programmable 4 axis controller touch screen 15” Setup virtual infinite rolling programs with teach-in mode and cad/cam operator interface --- Hydraulic motorized driven the central rolls Pre-pinch load adjustable for pre-bend Drop-end top roll front open unloading closed shells Re-rolling system for welded shells calibration. Safety and emergency stop Manuals and schematics machine dimension 5500x2000x2100 mm -weight 17ton --- Additional accessories available with the machine to agree on request nr.1 central support hydraulic 2.2 ton capacity to support large shell dia up to 4,5 meters id nr.1 side support hydraulic left side 2.2 ton double arm nr. 1 side support hydraulic right side 2.2ton double arm Gkedpfx Aisy Tbf Iovjc

Condition: defective spare-parts repository (used), Used three-roll round bending machine with a roller length of 2000 mm and a roller diameter of 170 mm. Mechanically in good condition. A new electrical wiring installation is required. Gkjdpfez N Hr Ujx Aivjc

Condition: ready for operation (used), Year of construction: 1996, Picot rolling machine Type RCS 205 – 30 cn Capacity: 6 mm rolling and 4 mm edging Gsdpfx Aez Rvlyeivekc CNC controlled Year: 1996 Rollers in very good condition Minimum coil diameter: 266.5 mm (6 mm rolling and 4 mm edging) Maximum coil diameter: 2050 mm (10 mm rolling and 6 mm edging)

Condition: used, Year of construction: 2001, functionality: fully functional, Profile Bending Machine SAF Curvatrici (TUWI) DS 60 HV – Top Condition & Huge Tool Package Description: For sale is a high-quality profile bending machine, type SAF Curvatrici (TUWI) DS 60 HV, from the first owner. The machine was purchased new by us in 2001 and has been in our possession ever since. It is fully operational and can be demonstrated under power after prior consultation. Special highlight – Modernized control system (08/2019): The control system was completely overhauled and modernized by a specialist company in August 2019. Now, 10 different feed sequences can be programmed. After a programmed value is reached, the next value is automatically approached by pressing the button again (value input in ascending order). Technical data & equipment: • Shaft diameter: 50 mm (for all three axes) • Acceptance height: 115 mm • Additional equipment from factory: 2 RCD correction rollers for bending angle iron (R/L). The original, lateral and height-adjustable shafts (38 x 250 mm) are also included. • Special modification for transport: Specially manufactured base frame for transport including four height-adjustable support plates. • Additional device for angle iron: A 10 mm thick plate was mounted on the top side. An additional hydraulic cylinder can be attached here, which pushes the vertical flange extremely close to 90° during bending (adjustable pressure depending on the angle). Note: The cylinder is not included in the standard price, but can be requested separately. Enormous scope of supply (Extremely many tools included!): The biggest advantage of this offer is the extremely extensive tool package, which is completely included in the price: • Standard tools: Complete set according to the machine’s scope of supply • 18 different roller sets: According to the list from Ø 8 mm to Ø 33.7 mm • Special tools for angle iron (according to the list) • Special tools for flat steel (light & heavy axis) • Special tools for square and rectangular tubes • Special tools for diagonal square material • Documentation: Original operating manual is fully available Note: The machine will only be sold as a complete package together with the complete tool set according to the attached list. Sales and delivery conditions: • Pricing: Ex works (net, plus VAT). • Logistics: The disassembly, loading and collection must be organized and carried out by the buyer himself or by a forwarding agent commissioned by him. Gkedpfx Aiez Ix Uksvsc Technical specifications according to available documents. Subject to prior sale.

Condition: like new (used), Year of construction: 2021, Hydraulic 4-roll bending machine Godpfjz I D Agsx Aivekc Digital display of roll positions Capability to form cones Length: 3050 mm Diameter of upper rolls: 220 mm Diameter of side rolls: 180 mm Bending capacity: 7 to 8 mm with a minimum radius of 1000 mm Machine dimensions: 4700 x 1100 x 1330 mm Weight: 5700 kg Operating videos available upon request.

Condition: used, Year of construction: 1987, rolling capacity max. NA t workpiece diameter 38 mm Gsdpfxst Hw D De Aivekc workpiece length 500 mm total power requirement 24 kW weight of the machine ca. 10 t dimensions of the machine ca. m Max.Ø tool slide stroke 760 mm Max.Ø rack length 610 mm Length of workpiece between centres, approx. 500 mm Max. tooth width / profile width 92 mm Max. workpiece Ø 38 mm Tailstock stroke on outboard support, hydraulic, approx. 500 mm Module range 0.3 - 1.3 Total electrical load, approx. 24 kW - 380 V - 50 Hz Weight, approx. 10,000 kg Accessories / Special Features * KBH Workpiece Feed Device, standing parallel to the machine, at present set-up for feed-in and feed-out of shaft-formed workpieces, approx. Ø 16 x 200 mm long, with prism conveyor belt and lifting station for 2 shafts (blank and finished part), as well as workpiece positioning control. * Originally, external gears were formed on the machine using pinion cages (no. of teeth = 25), Ø approx. 32 mm x 14 mm long, workpiece Ø approx. 80 x 80 mm long. * Various accessories: * Separate switch cabinet. * Separate hydraulic unit, 900 l. * Coolant device in the machine. * Control panel with malfunction message in plaintext, etc. Roto Flo machines are ideal for mass production of smaller gears/profiles. The coldforming process is a lot faster and more economical than other chip removing methods. Workpieces are clamped between 2 live centres and 2 synchronous opposed directional coldforming racks simultaneously engage the workpart and start rotation. During rotation, the profile is formed successively within one stroke. In the calibrating zone, the profiling and surfacing performance of the tool are optimised. Profiles do not require a run-out. The coldforming process requires a rigid and heavy duty construction of the machine, which ensures the required precision over the years. Between 25,000 and 100,000 working cycles can be performed with one set of racks, also for serrations. Condition : Very good. Machine can be inspected under power. Delivery : Ex stock, as inspected. Payment : Net, after conclusion of contract. Thank you for your interest. We always have a good selection of gear machines available. Please let us know what you need.

Condition: good (used), overall weight: 2,300 kg, spindle diameter: 0 mm, total height: 1,375 mm, total length: 1,645 mm, total width: 1,520 mm, One - Good used Profiroll Model UPWS 16 - 16 ton Hydraulic Thread Rolling Machine with swivelling spindles for in-feed or thru-feed rolling. Max threaded dia. 70mm Min. threaded dia. 3mm, Max width in=feed rolling: 150mm, rolling spindlle dia.: 69.85mm Godpfszt R T Esx Aivjkc power of main motor: 6.5 kw Complete with coolant equipment, work rest blade holder and five sets of thread dies.

Condition: good (used), functionality: fully functional, Year of construction: 2004, machine/vehicle number: 4roll 2000x6 mm, control type: manual, degree of automation: manual, actuation type: hydraulic, number of rollers: 4, roller (bottom) diameter: 155 mm, roller (top) diameter: 165 mm, side roll diameter: 120 mm, roller diameter: 165 mm, roller length: 2,050 mm, working width: 2,000 mm, working height: 600 mm, sheet thickness (max.): 6 mm, sheet thickness steel (max.): 6 mm, sheet thickness stainless steel (max.): 6 mm, sheet thickness aluminum (max.): 8 mm, sheet thickness brass (max.): 10 mm, sheet thickness copper (max.): 10 mm, overall weight: 2,200 kg, total length: 3,400 mm, total width: 1,150 mm, total height: 1,100 mm, power: 2.21 kW (3.00 HP), input voltage: 400 V, input frequency: 50 Hz, number of digital displays: 2, Equipment: cone bending device, emergency stop, hardened rollers, -roll 2000x6 mm plate bending machine Davi model MAX2017 year 2004 used plate roll in working condition, Planetary dual pre-pinch Performance Capacity: Plate width 2000 mm plate thickness 6 mm pre-bend 5 mm minimum rolling diameter ID 350 mm rollers length 2050 mm Gkedpfxozy N Afj Aivoc Upper roll 165 mm Pinch roll 155 mm Side rolls 120 mm Power electric motor 3 kw on hydraulic unit Vac 400/50 mm Installed configuration Rollers surface hardened high strength Conical plate rolling, cone bending Hydraulic commands via leverage distributors Infinitely variable speed control Digital position readout --- Hydraulic driven motorized the central rolls Pre-pinch pressure adjustable for pre-bend Drop-end front open to unload closed shells Re-rolling system for calibration of welded shell Safety and emergency stop machine dimension 3400x1150xH 1100 mm -weight 2200kg

Condition: good (used), functionality: fully functional, Year of construction: 2010, machine/vehicle number: SY 330 -075, control type: CNC control, degree of automation: automatic, actuation type: hydraulic, controller manufacturer: Akyapak, number of rollers: 4, roller (bottom) diameter: 300 mm, roller (top) diameter: 330 mm, overall weight: 9,100 kg, total length: 4,585 mm, total width: 1,610 mm, total height: 1,840 mm, input voltage: 400 V, input current: 35 A, input frequency: 50 Hz, Equipment: documentation/manual, emergency stop, foot remote control, hardened rollers, The sale includes a 2-meter longitudinal welding station equipped with an Oerlikon MIG 500 A welding unit, with all equipment in full working order. Also included are a lifting table for material handling to the plate rolling machine and a work platform. Godpfxjzzdahs Aivjkc The plate rolling machine is in good condition and can be put into production immediately. The machine is currently operational, and inspection and test runs can be arranged upon request. With the inclusion of the longitudinal welding station, this package provides a complete solution for manufacturing tubes and special pipe sections to customer-specified diameters, with lengths of up to 2 meters.

Year of construction: 2008, condition: ready for operation (used), We are offering this ready-to-use Roll-o-Matic roller die-cutting machine, roller size 0.932/3000, manufactured in 2008. Gjdoz Ag Ukepfx Aivekc Usable roller width: 3000 mm. The upper roller has a diameter of 320 mm and is equipped with a PA or cast nylon cutting sleeve. The roller gap can be adjusted independently on both sides and is equipped with an absolute value display for the roller gap. Operating modes: setup operation; semi-automatic operation; fully automatic operation with a light barrier and time control. Includes 5 conveyor belts, a counter, and additional equipment: support rollers for the lower roller to reduce deflection under high load. Chain drive and more powerful motor. Includes control buttons on both sides. If you have any questions or require more information, please send us a message or call us.

Year of construction: 1999, condition: used, functionality: fully functional, We are offering this used CMC Cevenini ET7 roll slitting machine, manufactured in 1999, for sale. The machine has been fitted with a new control system and is in good used condition. Only the compressed air hoses should be replaced when the opportunity arises. The machine is currently out of operation and is being sold due to a new acquisition and space constraints. Gedpfszzq E Rsx Aivjkc It is ideal for beginners who are looking for a reliable machine in the adhesive tape or film segment. It is also excellent as a core cutting machine. The price is negotiable. We welcome suggestions. If you have any questions or require further information, please feel free to send us a message or call us.

Condition: excellent (used), Akbend ASM140 Bending Rolls Gkodoz Hdv Djpfx Aivsc 3 Rolls 140mm top roll 1250mm length x 5mm thickness Year 2007 Motor power 2.2kw

Condition: excellent (used), overall weight: 1,350 kg, spindle diameter: 40 mm, type of input current: three-phase, total height: 1,500 mm, total length: 1,000 mm, total width: 1,000 mm, One - Very Good Used ORT Model RP10/U - 10 ton Hydraulic Thread Rolling Machine with swivelling spindles for in-feed or thru-feed rolling Gsdpfx Aijzt R Rwjvekc Max. threaded diameter: 30mm Min.threaded diameter: 2mm Max. width in-feed rolling: 65mm Power of main motor: 4 kw Complete with coolant equipment , work rest blade holder ,open fronted spindle front supports for easy access with small dia. components - 13 set of in-feed thread dies

Condition: excellent (used), functionality: fully functional, Year of construction: 2024, actuation type: electric, roller diameter: 90 mm, working width: 1,270 mm, sheet thickness (max.): 3 mm, overall weight: 520 kg, power: 1.1 kW (1.50 HP), input voltage: 400 V, rotational speed (max.): 6 rpm, type of input current: three-phase, Equipment: cone bending device, emergency stop, foot remote control, hardened rollers, swiveling upper roller, sheet metal roll bending machine BOLUK BM 1270 x 90 - 2.5 mm NEW! for sale. manufacturer: BOLUK 1270X90mm year of manufacture: 2024 Bending Length: 1270 mm Bending capacity: 2.5 mm Roller diameter 90 mm - SAE 1050 certified high tensile steel rollers - Wire grooves at the ends of the rollers (4/6/9) mm - Manually adjustable rear roller Gksdpjxhub Aofx Aivjc - Mobile control panel with foot pedal - Precision bending with brake motor - Conical bending device - Manually foldable end - Cast iron main frames Bending speed 6m / min Motor power 1.1 kW 50Hz 380v Wire groove diameter 4/7/10 mm Machine dimensions 1850x700x1200 mm Weight 520 kg

Year of construction: 2008, condition: ready for operation (used), functionality: fully functional, paper width (max.): 1,800 mm, Unwind diameter: 1,000 mm Rewind diameter: 800 mm Max. speed: 400 m/min Friction shafts for 3 and 6 inch Hydraulic lift at the unwind station Splicing table Web edge control Tidland knife holders, 20 pieces Semi-automatic knife setting system from Tidland Recipe management Laser positioning We will also dismantle and load the machine onto a truck or sea container at our own expense. Gjdeywl D Nopfx Aivjkc

Condition: good (used), workpiece weight (max.): 80,000 kg, grinding diameter: 1,580 mm, grinding length: 7,500 mm, Manufacturer: Farrel Type: 60" x 24" Heavy Duty Year of manufacture: 1960 Travelling wheel machine with CROWNING and CONCAVING grinding Equipped with stones / flanches / lubrication / coolant system Maximum diameter full size wheel 1550 mm Work swing over bed 1580 mm Work load 180,000 pounds (81,000 kg) Grinding length 7500 mm Specifications Metric US Standard Center height 930 mm Grinding diameter Ø 1860 mm Grinding length 7500 mm Grinding stone dimensions 1080 x 180 mm Grinding stone speed 400 - 100 rpm Tailstock 260 x 1250 Mk Coolant system Yes filter Yes Dimensions (estimate) length 13200 mm width 4250 mm height 3200 mm weight 80000 kg Please note: The information on this page is given in good faith and to the best of our knowledge, and where possible, has been obtained from the manufacturer, but accuracy cannot be guaranteed. Accordingly, it does not constitute a representation or contract and we recommend that you check all relevant details. Gkedpfx Aer Ikvmeivoc Share on download Travelling wheel machine with CROWNING and CONCAVING grinding Equipped with stones / flanges / lubrication / coolant system Maximum diameter full size wheel 1550 mm Work swing over bed 1580 mm Work load 180,000 pounds (81,000 kg) Grinding length 7500 mm Center height: 930mm Grinding diameter Ø: 1860mm Grinding length: 7500mm Grinding stone dimensions: 1080 x 180mm Grinding stone speed:400 - 100Rpm Tailstock: 260 x 1250Mk Coolant system: Yes Filter: Yes Length: 13200mm Width: 4250mm Height: 3200mm Weight: 80000kg Aluminum Industry Non-Ferrous Industry Paper Industry Roll Manufactures Steel Industry Plate Mill Hot Rolling Mill Cold Rolling Mill Travelling wheel machine with CROWNING and CONCAVING grinding Equipped with stones / flanches / lubrication / coolant system Maximum diameter full size wheel 1550 mm Work swing over bed 1580 mm Work load 180,000 pounds (81,000 kg) Grinding length 7500 mm Center height: 930inch Grinding diameter Ø: 1860inch Grinding length: 7500inch Grinding stone dimensions:1080 x 180inch Grinding stone speed:400 - 100Rpm Tailstock: 260 x 1250Mk Coolant system: Yes Filter: Yes Length: 519.684inch Width: 167.323inch Height: 125.984inch Weight: 176449.6lbs Aluminum Industry Non-Ferrous Industry Paper Industry Roll Manufactures Steel Industry Plate Mill Hot Rolling Mill Cold Rolling Mill Aluminum Industry Non-Ferrous Industry Paper Industry Roll Manufactures Steel Industry Plate Mill Hot Rolling Mill Cold Rolling Mill