Thread rolling machine, cold rolling machine, thread rolling machine, profile rolling machine, threa
PEE-WEE UPW 24

Name: PEE-WEE UPW 24
Brand: PEE-WEE
Price: 23000 EUR
Availability: InStock

Fixed price plus VAT

€23,000

Condition

Used

Location

Hessisch Lichtenau Germany

Show map

Machine data

Machine type:: Thread rolling machine, cold rolling machine, thread rolling machine, profile rolling machine, threa

Manufacturer:: PEE-WEE

Model:: UPW 24

Condition:: used

Price & Location

Fixed price plus VAT

€23,000

Location:: 37235 Hessisch Lichtenau

Call

Details about the offer

Listing ID:: A17492123

Reference number:: 60168

Update:: 06.03.2026

Description

Thread Rolling Machine, Cold Rolling Machine, Thread Rolling Machine, Profile Rolling Machine
Manufacturer: PEE-WEE Model: UPW 24
Serial No.: P07 Year of manufacture: 2007
Maximum rolling force: 24 tons
Maximum tool diameter: 270 mm
Roll spindle diameter: 69.85 mm
Tool bore diameter: 70 mm (nominal diameter)
Maximum tool/reception length: 180 mm
Maximum workpiece diameter: 50 mm
Ncjdouz If Njpfx Aaasr
Hydraulic motor power: 3 kW
Roll drive motor power: approx. 5.5 kW
Electrical connection: 400 Volt, 50 Hz, 10 kW
- Pivotable roll spindle for through-feed thread rolling
- Roll spindle speed adjustable in 4 steps via gearbox shift
- Hydraulic unit integrated in the machine base
- Operating manual with electrical schematic
Space requirements (L x W x H): 2,000 x 1,450 x 1,900 mm
Weight: approx. 3 tons
Very good condition

Plunge Rolling: The thread rolling tools, having the same pitch as the workpiece, form the thread by penetrating the workpiece up to the nominal diameter. The maximum thread length is limited to the width of the rolling dies.

Through-feed Rolling: Used when the thread length is greater than the width of the rolling dies. Through-feed tools are divided into three sections – entry, calibration, and exit.

Knurling rolls have no pitch and are swiveled at the lead angle corresponding to that of the profile to be rolled.

Lead angle rolls differ from knurling rolls by having a pitch in the profile. The sum of the lead angle and swivel angle results in the effective lead angle in the workpiece.

The listing was translated automatically. Translation errors are possible.

Seller

Registered since: 2013

598 listings online

Call

Send inquiry

Message*

Name*

E-mail*

Telephone

Company name

Zip code & cityCountry

I am a dealer

Receive offers for similar machines

Note: Your inquiry will be forwarded to all sellers in this machine category. This allows you to receive a large number of offers.

Privacy statement

Telephone & Fax

+49 5602 ... show

Fax:

These listings may also fit your interest.

Listing

Sweden

1,192 km

NAKAMURA-TOME WY150
NAKAMURA-TOMEWY150

Call

Condition: ready for operation (used), Year of construction: 2023, number of axes: 9, This 9-axis NAKAMURA-TOME WY150 was manufactured in 2023, featuring a turn-mill centre with a comprehensive toolholder setup including 6 external, 4 internal, 3 radial rotating, and 12 axial rotating holders, plus a collet chuck and a 3-jaw chuck. Consider the opportunity to buy this NAKAMURA-TOME WY150 turn-mill centre. Contact us for more information. Additional equipment • 6 external toolholders • 4 internal toolholders • 3 radial rotating (driven) toolholders Njdpsyb Sakofx Aaaecr • 12 axial rotating (driven) toolholders • 1 collet chuck • 1 three-jaw chuck

See details

Listing

Multi-Tasking CNC Turning Center Spinner TTS65-Triplex

Germany

1,293 km

Multi-Tasking CNC Turning Center
SpinnerTTS65-Triplex

Call

Year of construction: 2019, condition: ready for operation (used), A simultaneous turning center Spinner with three turrets and extensive accessories, spare parts and tools is available. Travel X1/X2/X3: 180mm, travel Y1/Y2: +/-45mm, travel Z1/Z3: 704mm, travel Z2/E2: 620mm/720mm, rapid traverse X/Y/Z: 30m/min, acceleration: 0.5g. Spindle 1: Speed: 5000rpm, nose: A6, bore: 65mm, chuck diameter: 210mm, power: 18kW, torque: 115Nm. Spindle 2: Speed: 700rpm, nose diameter: 110mm, bore: 42mm, max. chuck diameter: 140mm, max. chuck jaw weight: 1.25kg, power: 16.6kW, torque: 100Nm. Turret 1/2/3: Turret stations: 3x12, speed: 8000rpm, tool holder: BMT 45, power: 4.3kW, torque: 13.6Nm. Machine dimensions X/Y/Z: approx. 2880mm/2130mm/1990mm, weight: approx. 7500kg, operating hours: 27102h, control: Fanuc 31i. Including loading magazine Top Automazioni, cooling/high pressure system with 80bar, chip conveyor, fire extinguishing system, a comprehensive tool package and other spare parts. Documentation available. On-site inspection is possible. Nsdpfx Aaoua E Trjaocr

See details

Listing

CNC Turning- and Milling Center MORI SEIKI ZL-150SMC

Hattingen

1,070 km

CNC Turning- and Milling Center
MORI SEIKIZL-150SMC

Call

Condition: used, Year of construction: 1999, swing dia. 680 mm max. turning diameter 429 mm turning length 440 mm control MORI SEIKI - MSC-501 turning speeds 5.000 U/min max. bar material dia. 56 mm travel -x axis 233 mm travel -z axis 510 mm Ncodpfx Aaewpluloajr number of tapers in turret head 2x12 CNC Turning- and Milling Center | MORI SEIKI - ZL-150SMC equipped with main/counter spindle, c- axis, 2x turret for driven tools, bar feeder and chip conveyor. The machine is in a well-maintained condition. Please note that the technical details were added from comparable machines. - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - #Tags: ZL 150SMC | ZL150SMC | ZL-150 SMC | ZL 150 SMC

See details

Listing

Gräfenthal

1,375 km

Single side decoiler
BBTABH 2000

Call

Condition: as good as new (ex-display), Year of construction: 2021, machine/vehicle number: 06 61 218, Comm. no.: Lg 32821 Single side decoiler BBT ABH 2000/400 exhibition machine, unused machine no.: 06 62 218 year of manufacture: 2021 Technical data Nodeg U Utvjpfx Aaaecr load capacity approx. max. 2.000 kg strip width max. 400 mm Coil inner diameter approx. 450 to 520 mm Coil outer diameter max. 1,500 mm Unwinding speed approx. 2 to 15 min.-1 With adjustable drive and loop control via ultrasonic sensor (analog). Drive by frequency-controlled three-phase geared motor. Spreading of the support segments manually by means of hand crank via joints Number of supporting segments 3 Coil side guide via strong limiting arms, clampable. Reel stand in strong box construction as welded design. construction. Additional equipment: Shutdown "belt loop too small" by antenna switch, attached to the column of the bottom housing of the loop control. Infinitely adjustable in height. Tape side guide at the bottom housing of the loop control, by means of lateral guide rods. The passage width is continuously adjustable.

See details

Listing

Eccentric Press - Single Column SCHULER PD 63-250

Eislingen/Fils

1,357 km

Eccentric Press - Single Column
SCHULERPD 63-250

Call

Listing

Turn-Mill Centre MORI SEIKI NLX 2500 SY/700

Spain

1,481 km

Turn-Mill Centre
MORI SEIKINLX 2500 SY/700

Call

Condition: ready for operation (used), Year of construction: 2010, General Data Measurements width 3056 mm Measurements depth 3994 mm Measurements height 2187 mm Machine weight 6360 kg Main Drive Spindle speed range 4000 Number of axis 5 Movement X-Axis Movement 260 mm X-Axis Rapid Traverse 30000 mm/min Y-Axis Movement ±50 mm Y-Axis Rapid Traverse 0000 mm/min Z-Axis Movement 795 mm Z-Axis Rapid Traverse 30000 mm/min B-Axis Movement 734 mm B-Axis Rapid Traverse 30000 mm/min Workpiece Workpiece drm over bed 590 mm Workpiece drm over support 360 mm This 5-axis MORI SEIKI NLX 2500 SY/700 was manufactured in 2010, featuring a max swing over bed of 590 mm and a cutting length of 795 mm. It includes Y and C axes, a sub-spindle, and high-pressure coolant system. Capable of handling bar work up to 80 mm, it's equipped with a chip conveyor and automatic bar feeder. Consider the opportunity to buy this MORI SEIKI NLX 2500 SY/700 turn-mill centre. Contact us for more information about this machine. Application Types Turning Ncodpjx D Sc Nofx Aaasr

See details

Listing

Horizontal machining center QUASER HX404BP/15C

Contamine-sur-Arve

1,321 km

Horizontal machining center
QUASERHX404BP/15C

Call

Condition: used, TECHNICAL DETAILS - Number of axes : 4 MILLING SPINDLE - Tool holder type : BT40 BIG PLUS - Spindle power : 26 [kW] - Spindle speeds : 15000 [rpm] LINEAR AXES - Travels on X/Y/Z axes : 560/640/640 [mm] - Rapid traverses rates (X/Y/Z) : 60 [m/min] B ROTARY AXIS - Travel : 360 [°] - Indexing precision : 0.001 [°] TOOL CHANGER - Auto. Tool Changer type : Bras chargeur - Tool magazine capacity : 60 PALLET CHANGER - Pallet changing device type : Rotopalette - Pallet size : 400X400 [mm] - Pallets number : 2 - Maximum weight upon pallet : 400 [kg] - Maximum workpiece diameter : 630 [mm] - Maximum workpiece height : 900 [mm] POWER SUPPLY - Supply voltage : 400 [V] WEIGHT & DIMENSIONS - Machine floor space : 4100X2300 [mm] - Machine height : 2720 [mm] - Machine weight : 11000 [kg] MACHINE HOURS - Number of working hours : 3700 [h] EQUIPMENT - CNC : Fanuc 31 iB Interface : Ethernet / RS232 / USB / PCMCIA - Electronic handwheel Njdpfx Asuhbv Ssaajcr - Linear scales - Rigid tapping - 3 colors status lamp - Coolant tank * with high-pressure pump : 25 [bars] * Coolant through spindle * With cabin washing - Chips conveyor : Arrière - Spindle cooling unit - Tool probe - Workpiece probe : Renishaw OMP60

See details

Listing

Gussago

1,583 km

ORT RP30U inverter
ORTRP30U inverter

Call

Condition: used, Thread rolling machine ORT RP30U 2-roll Ncsdpfx Ast H Ty Uoaajr 30 ton swiveling heads variable speed drive #1331 Under power in our warehouse in Gussago BS. Test run possible M i m u Machine Tools Italy Rolling is a mechanical process without chip removal that can be performed cold or hot, having as a purpose the improvement of the surface finish (therefore the fatigue behavior Power (Ton): 30 Number of rollers: 2

See details

Listing

Vertical Turning Machine Buderus BV 1250

Hilden

1,061 km

Vertical Turning Machine
BuderusBV 1250

Call

Condition: used, Year of construction: 2008, turning diameter 1000 mm swing diameter 1250 mm turning height 500 mm control Siemens Sinumerik 840 D Workpiece spindle flange diameter 520 mm work piece spindle speed range 0-440 U/min total power requirement 75 kW weight of the machine ca. 25 t dimensions of the machine ca. 5100 x 3034 x 4500 mm With grinding spindle Table travel: - Z1/Z2 axis 1000 mm, - X1/X2 axis approx. 1300 mm Table speed continuously adjustable: - Z axis 0–30 m/min, - X axis 0–50 m/min - Feed speed continuously adjustable 0.01–15 mm/min - Feed dependent on stroke 0.0005–0.1 mm - Workpiece spindle positioning C axis Equipment/accessories: - Grinding spindle - Kaiser dresser - Tool measuring probe Ncedpjw Rgcfofx Aaaor - Filter system - With flushing nozzle connections - 2 Capto holders - 1 set of jaws for chuck - technical documentation

See details

Listing

Machining center starrag Heckert HEC400D

Butzbach

1,206 km

Machining center
starrag HeckertHEC400D

Call

Condition: good (used), Year of construction: 2015, travel distance X-axis: 650 mm, travel distance Y-axis: 650 mm, travel distance Z-axis: 650 mm, 1 Horizontal machining center Make: STARRAG HECKERT, type: HEC 400D, year 2015, Control system, Siemens, type Sinumerik 840D, travel X/Y/Z = 650 x 650 x 650 mm, 2-fold pallet changer, pallet size 400 x 400 mm, NC rotary table 360x 0.001°, 80-fold tool changer, Ncsdpfouav H Nox Aaasr HSK 63 tool holder, spindle speed 15,000 rpm, IKZ 50 bar, belt filter, coolant temperature control, spindle cooling, chip conveyor, sound and control cabinets, operating hours 43,698, spindle hours 5,401

See details

Advertise here