Used Cnc Milling Machining Center for sale (70,365)

Condition: used, Year of construction: 2001, Used machine Year of manufacture: 2001 Condition: Function tested Equipment and technical data: Milling unit: 4.4 kW Tool holder: HSK 63 F Speed: 1,000 - 18,000 rpm Water-cooled Tool changer: 4-position, lateral Drilling head: 9 vertical drilling spindles on a 32 mm pitch Horizontal drilling spindle: 1+1 Vertical drilling spindle: 1+1 Grooving saw in X-direction Control: Twin CAM 32 Vacuum pump: 40 cbm/h Including vacuum suction cups Travel paths: X-axis: 2,685 mm Y-axis: 1,095 mm Z-axis: 140 mm Weight: approx. 3,500 kg The machine is completely checked for all mechanical, electrical, and electronic components and overhauled where necessary. Lhodpow I Ug Hjfx Al Ieh All guides checked; console guides replaced New PC control system for the TWIN CAM control All axis modules checked and serviced Location: Flörsheim Availability: by arrangement

Condition: used, Year of construction: 2019, Used machine Year of manufacture: 2019 Only 110 operating hours! Equipment and technical data: X = 1800 mm Y = 900 mm Z = 80 mm Made from 18 mm Koskisen panels, consisting of a milling table (X-axis), a gantry (Y-axis), and a Z-axis. Milling bed in 19 mm MDF used as a sacrificial plate with guide rails and T-slot nuts for clamping. Subframe with reinforcements, filled with polymer concrete, prepared for transport with pallet truck or forklift. Mechanical set consisting of profile guides including guide carriages, as well as ball screws 2010 and 1605 for all axes. Shaft couplings and high-performance grease for lubricating the individual carriages, as well as energy chains including connection sets. Control set consisting of a Triple Beast, for controlling 3 axes, with Ethernet interface. Leadshine driver for the fourth motor. Four stepper motors, 5.0A, 3Nm with motor cables, as well as power supply unit with 48V, 6.7A, LED board for breakout board, ribbon cable and proximity sensors, small parts like single-core wires, wire end sleeves, control cables, heat shrink tubing, and cable lugs. Fully installed in an aluminum enclosure including electrical wiring and emergency stop. 21.5 inch built-in monitor, including mini PC with Windows 7, CAD software Rhino 5.0, G-code generator Estlcam, control software Beamicon2, as well as mouse and keyboard, pre-installed in an ergonomic control desk. Tool length sensor for determining the length and updating the active zero offset. Special equipment: High-frequency spindle with 2.2 kW, including locknut, frequency inverter, line filter, braking resistor, and collet set. Lhsdjw Nadyepfx Al Ieh PC with 8 GB RAM and AMD processor CAD software Rhino 5.0 for creating both simple 2D data and 3D solid models Availability: short-term Location: Flörsheim

Condition: used, Year of construction: 2016, Used machine Year of manufacture: 2016 Equipment and technical data: Working area X: 3,400 mm Working area Y: 1,287 mm Working area Z: 180 mm Number of milling spindles: 1 Main motor: 15 kW Speed max: 24,000 rpm 4th axis Tool clamping system: HSK-F63 Tool changer positions: 18 Vertical drilling spindles: 18 Horizontal drilling spindles X: 6 Horizontal drilling spindles Y: 2 Nut saw in X direction Design: Cantilever machine Machine table: Console table Number of consoles: 6 Positioning aid: Dot laser Number of vacuum pumps: 1 Capacity of vacuum pumps: 140 m³/h Safety device: Foot mat Control system: BECKHOFF CONTROL Software: HOLZ-HER CAMPUS V6.4 Conformity marking: CE marking Weight: approx. 3,840 kg Space requirement length: 6.7 m Space requirement width: 4 m Availability: Short notice, by arrangement. Ledpfjzc Sk Esx Al Ishh

Year of construction: 2025, condition: new, Demo machine Year of manufacture: 2025 Travel range: 2500x1300x200mm Machine frame in 19mm Forescolour, consisting of milling table (X-axis), gantry (Y-axis), Z-axis unit in compact board, and base frame with adjustable machine feet. Milling bed as sacrificial board in 19mm MDF. Table openings longitudinally and transversely pre-configured. Mechanical set consisting of profile rails including profile rail carriages, ball screw and precision rack gears. All components assembled, pre-lubricated including test run, immediately ready for operation. Control set consisting of control cables, energy chains, planetary gears, stepper motors, high-performance drivers, power supply and toroidal transformer, all preinstalled in the control cabinet, as well as sensors for each axis. Control relay for automatic actuation of the existing extraction system. Brush seals for dust protection and protective equipment compliant with CE regulations: includes moving extraction unit and one-sided mounted laser scanner for work area monitoring, with 275° and 5.5m field range. (Machine positioned in a room corner) Manual control panel equipped with all necessary machine functions, including emergency stop and dead man’s switch. Tool length sensor for determining tool length and active offset of the reference point. Lhedpfxoxc Rmqs Al Ijh High-frequency spindle with 2.2 kW, incl. clamping nut, frequency inverter, power filter, breaking resistor, and collet set. Built-in monitor, incl. mini PC with Windows 11, control software Beamicon2, mouse and keyboard, pre-installed in an ergonomic console. CAD license Rhino 8.0 and CAM license Estlcam V12, as well as all necessary documentation, will be sent by email prior to delivery. Includes milling bed designed as a vacuum table, consisting of four individually controllable segments. Cross table made of PE with top layer in MDF. Becker vacuum pump with a capacity of 100m³/h, oil-lubricated. A 16 Amp, 400 V AC plug is required for the vacuum pump electrical connection. The customer must provide HDF 3mm raw on both sides for the whole vacuum table (2500x1300mm) as a sacrificial board. (Recommended application: machining of coated wood-based panels) Includes 10-piece tool set consisting of: 3 pcs. 5 mm Z2 (HF52REVHM) 6 pcs. 4 mm Z1 (HF41REVHM) 1 pc. 5mm Z3 (HF53SRECAR) (Tool selection can be adapted as needed) Includes maintenance package in systainer: - 150 ml grease gun - 400 g cartridge high-performance grease - 500 ml can of silicone spray grease - Grease nipple incl. hose and 30mm face mill with indexable inserts Availability: short notice Location: Flörsheim

Condition: used, Year of construction: 2019, Used machine Year of manufacture: 2019 Equipment and Technical Data: - For classic nesting processing with wear plate - Machine frame of welded construction with ground and hardened prism guides for the gantry, unit head, and consoles - Gantry-type traveling column - Helical rack and pinion drive in X and Y axes, ball screw in Z axis for precise positioning - Working dimensions: - Max. support area on nesting table: X = 3100 mm, Y = 1560 mm Lhjdpfewka Upsx Al Ioh - Max. traverse paths: X = 4695 mm, Y = 2100 mm, Z = 293 mm - Max. clearance height over DYNESTIC table: Z = 100 mm from table top (without wear plate) - Maximum programmable speed Vector speed: 128 m/min X = 80 m/min, Y = 100 m/min, Z = 25 m/min - DYNESTIC table: - Fixed, continuous processing table with grid layout - Continuous grooves in X and Y directions - Groove spacing: 50 mm - Includes 25 meters of sealing cord for clamping the wear plate - Vacuum fields: Single-circuit vacuum system - Drilling unit 7877: - 19 spindles - Drive power: 1.7 kW - 13 vertical spindles: - Individually selectable - Arranged in U-shape - 5+4 in X direction, 4 in Y direction - 32 mm spacing - Max. drill diameter: 35 mm - Total drill length: 70 mm from screw-on end (depending on panel thickness) - Spindle stroke: 70 mm - Rotational direction: alternating clockwise/counterclockwise - Speed (max): 1000 - 4400 rpm, infinitely variable - Tool holder: M10 thread, 11 mm fit - Without tool, without holder - 6 horizontal spindles: - 2 double drill spindles in X direction - 1 double drill spindle in Y direction - Tool holder: M10 thread, 11 mm fit - Max. total drill length: 63 mm from screw-on end - Without tool, without holder - Milling unit 7842: - Power: 12.0 kW (S6) - Max. speed = 1000 - 24,000 rpm, infinitely variable - Max. power at 12,000 to 24,000 rpm - Air-cooled - With HSK-F 63 tool holder - With right-hand threaded nut (for right-hand rotating tools) - With collet chuck for HSK shank - Ceramic ball bearings (hybrid bearings) - Tool weight max. 6 kg (incl. holder) - Tools: milling and grinding tools max. Ø 160 mm - Safety enclosure according to CE standard - Side and rear safety fence - Vacuum pump: 500 m³/h, dry-running - Personnel safety ensured by light barriers in the front machine area - Hand-held control device for remote operation of the machine with the following functions: - Start/stop of the processing program - Control of processing cycle speed - Reset button - Manual feed/rapid traverse for all axes - EMERGENCY STOP - CAMPUS V7 CAD/CAM software 1x machine license consisting of: - CAMPUS NC-HOPS: - Graphic variant system with WOP and CAD/CAM features for creating part variants using macro technology - CAMPUS MT-Manager - CAMPUS Workcenter - CAMPUS DXF interface - Automatic central lubrication - Automatic lubrication at defined intervals - Additional sealing against dust via pressurization in each guide carriage

Condition: used, Year of construction: 2000, max swing 700 mm, X/Y 255/520 mm, 12-position upper tool turret and 8-position lower tool turret with driven tools, measuring head, tailstock, CNC SIEMENS SINUMERIK 840D, 400V 50Hz 45kW, weight 15 t Ljdpfx Aloym Sx De Iehh

Condition: used, Year of construction: 2009, travel -x axis 600 mm travel -y axis 450 mm travel -z axis 450 mm control HEIDENHAIN - TNC 530 number of spindle speeds 18.000 U/min tool taper HSK-A63 numbers of positions in the tool changer 120 5-axis simultaneous machining center | HERMLE - C 20 U equipped with ITC (80 bar), NC swivel rotary table, 120-way tool changer & pallet changer. The machine is in a well-maintained condition. The machine videos from the production plant will be shared on request. Please refer to further technical details in the attachement of the offer. - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - #Tags: C 20 | C20 | C-20 | C20U Ljdpfx Aoyy A N Uel Ishh

Condition: excellent (used), Year of construction: 2021, operating hours: 2,500 h, functionality: fully functional, travel distance X-axis: 1,060 mm, travel distance Y-axis: 600 mm, travel distance Z-axis: 600 mm, controller model: Heidenhain ITNC640, spindle speed (max.): 10,000 rpm, We offer in good condition with around 2.500 spindle hours Posmill CE1000 with following options: Heidenhain linear scales in X, Y and Z-axis Heidenhain TNC 640 control Air true spindel Spindel 10.000 RPM ISO40 Tool changer 40 tools ATC Belt filter with Internal coolant 20 bar Hexagon Touch probe Hexagon tool probe Chip conveyor Thermal spindel compensation Z-axis Technical specification:" Lhedpfxjyindae Al Ijh X-Axis Travel: 1060 mm Y-Axis Travel: 600 mm Z-Axis Travel: 600 mm Machine is within new tolerence and geometry protocol is available.

Condition: excellent (used), Year of construction: 2015, operating hours: 3,900 h, functionality: fully functional, travel distance X-axis: 762 mm, travel distance Y-axis: 508 mm, travel distance Z-axis: 610 mm, spindle speed (max.): 18,000 rpm, operating hours of spindle: 3,900 h, We offer in very good condition Hurco VMX30 HSi with HSK-A63 spindle and 18k RPM. X-Axis travel: 762mm Ledox N E H Uspfx Al Iohh Y-Axis travel: 508mm Z-Axis travel: 610mm The machine has following options: Internal coolant 20 bar 40 Tool changer 18k RPM Spindle hSK-A63 Linear Scales Touchprobe Renishaw OMP40 Toolprobe Renishaw TS27R Ultimotion software Tool change optimization software Please not vices are not with sale of machine

Condition: like new (used), Year of construction: 2019, operating hours: 794 h, functionality: fully functional, travel distance X-axis: 650 mm, travel distance Y-axis: 520 mm, travel distance Z-axis: 475 mm, controller model: Siemens, overall weight: 7,750 kg, spindle speed (max.): 20,000 rpm, number of slots in tool magazine: 60, We offer an DMG DMU 50 in great condition with only 794 hours. Machine will be in stock next week. Lhodozb Em Ropfx Al Ieh Machine has following options: - Siemens 840D SL - Speedmaster Motorspindel 20.000 RPM 35 kW / 25 kW Torque 130 Nm / 86 Nm) SK40 - 60 tool automatic tool changer - Chip conveyor - Swivel table 630 x 500 mm - Internal coolant 20 bar - External air coolant - Air true spindle - Rotating clear view window - Spray Gun - Oil and emulsion mist separator - Touch probe Heidenhain TS460 - Tool measuring device Heidenhain TT160 - 3D quick set - Electronic handwheel

Year of construction: 1997, condition: good (used), Ibarmia CNC machining center offered. Type: ZVL 3000 Control unit: Heidenhain TNC 426 CB X-travel: 2200 mm Y-travel: 800 mm Z-travel: 600/800 mm Table: 850 x 2600 mm Weight on table max: 3500 KG Spindle: SK 40 with cooling Speed max: 4000 RPM Ljdpfx Alsh Hp Uns Ijhh Toolchanger: 40 pieces Power: 47 KW Included: documentation, parameters, toolholders, chip conveyor and central lubrication system Year: 1997 Dimensions: 625x305x340 cm LxWxH Weight: ca 12000 KG Movie available! For more information call us or send an e-mail.

Condition: used, Year of construction: 1997, MORI SEIKI SL-35 TURN MILL CENTRE MAKE MORI SEIKI, MADE IN JAPAN MODEL SL-35 YEAR 1997 CONTROL FANUC MSC 516 CHUCK DIA 400.0 mm MAX. TURNING DIA 400.0 mm MAX. TURNING LENGT 780.0 mm SWING OVER BED 600.0 mm OVER CROSS SLIDE 425.0 mm MAX. SPINDLE SPEED 9-2500 rpm TURRET 12 STATIONS TAILSTOCK YES SPINDLE BORE 82.0 mm SPINDLE NOSE A8 RAPID TRAVERSE RATE X: 12,000mm/min & / Z: 15,000mm/min PLUS SWARF CONVEYOR TOOL SETTING PROBE Lhjdpfjv N D Rtjx Al Ioh GOOD RANGE OF TOOLING MACHINE MANUALS CLEAN

Condition: like new (used), Year of construction: 2024, MAZAK QUICK TURN 200 MSY Max. machining diameter: 380 mm Max. machining length: 575 mm Max. milling speed: 5,000 rpm Lhodszgw Icopfx Al Ish Max. spindle speed: 5,000 rpm Max. bar diameter: 65 mm Machine is equipped with: - CNC control: Mazatrol SmoothG -Hydr. KITAGAWA 3-jaw chuck BB-208 for main spindle, diameter 210 mm -Hydr. KITAGAWA 3-jaw chuck B-206 for 2nd spindle, diameter 169 mm - Tool Eye - C-axis - C-axis counter-spindle, input accuracy 0.0001° - Y-axis - Interface for bar feeder - Autom. parts catcher - Robot interface - Reinforced coolant pump - MAYFRAN chip conveyor - 8 pcs. fixed tool holders - 2 pcs. driven tool holders

Condition: good (used), Year of construction: 2013, Main and counter spindle C-axis on main and counter spindle 2 x 12-position turret VDI 40 Y-axis Chuck flushing device Tool monitoring Brankamp Coolant system 980 liters with belt filter Conveyor belt Oil mist separator Lhjdsy Ivyiopfx Al Ioh Chip conveyor without bar feeder

Condition: excellent (used), Year of construction: 1999, CNC horizontal machining center DECKEL MAHO DMC 60 H SIEMENS CONTROL Year of manufacture: 1999 Lodpfxevn Ra So Al Ishh Technical data: X-axis: 600mm Y-axis: 560mm Z-axis: 560mm B-axis: 360° Pallet: Number: 2 Size: 400x500mm Permissible load: 600kg Weight: 10,500kg

Condition: used, Year of construction: 2022, total height: 2,400 mm, total length: 5,300 mm, total width: 2,350 mm, Colour: Grey Empty weight: 4.000 kg Price: On request - Year: 2022 - Documentation available: Yes - CE marking present: Yes - CE certificate present: No - Serial number: 30B.11.040.22 - Number of milling spindles [pcs.]: 1 - └ Milling spindle 1: - - Number of controlled axes [pcs.]: 4 - - Max. spindle speed [rpm]: 24000 - - Main motor power [kW]: 11 - Type milling table: Beam table - Drilling unit present: Yes - └ Horizontal drill spindles [pcs.]: 4 - └ Vertical drilling spindles [pcs.]: 12 - Saw unit present: Yes - Tool changer positions [pcs.]: 12 - Vacuum pump present: Yes - └ Number [pcs.]: 1 - └ Brand: Becker - └ Type: PICCHIO 2200 - └ Year of manufacture: 2022 - Tools included: Yes - Table length [mm]: 3300 - Table width [mm]: 1280 - Working range X [mm]: 3300 - Working range Y [mm]: 1280 - Z-axis working range [mm]: 250 - X-axis maximum stroke [mm]: 4000 - Y-axis maximum stroke [mm]: 1670 - Z-axis maximum stroke [mm]: 500 - Voltage [V]: 400 - Current consumption [A]: 40 - Power [kW]: 18.0 - Installed length [mm]: 6250 - Installed width [mm]: 3494 Lhjdpfxjx Tt Uns Al Ijh - Installed height [mm]: 2300 - Transport dimensions: 5300mm x 2350mm x 2400mm (l x w x h) - Transport weight [kg]: 4000kg - Transport packages [pcs.]: 2 Financial information VAT: The price shown is exclusive of VAT VAT/margin: VAT deductible for entrepreneurs Delivery and trade-in always possible for everything in the industrial sectors Glenn Smeets

Condition: used, Year of construction: 2014, total height: 2,400 mm, total length: 4,500 mm, total width: 2,200 mm, Colour: Grey Empty weight: 2.500 kg CNC Machining Center Biesse skill 12 24 G FT Year of construction 2014 Machine no. 60961 Recording HSK F63 10x vertical drilling 12 switch positions Software: BiesseWorks X axis 2465 mm Y-axis 1260 mm Z axis 324 mm Disassembled for transport on normal trailer; 4500x2200x2400mm; Lhjdpfxswnhanj Al Ioh Own weight 2000kg - Details: - └ Description: Pallet with white control box does not belong to this machine - Year: 2014 - Documentation available: Yes - CE certificate present: No - Serial number: 60961 - Number of milling spindles [pcs.]: 1 - Type milling table: Flat table - Tool clamping system: HSK-F63 - Drilling unit present: Yes - └ Vertical drilling spindles [pcs.]: 10 - Tool changer positions [pcs.]: 12 - System/software: BiesseWorks - Safety feature: Enclosed fence - Vacuum pump present: Yes - └ Number [pcs.]: 1 - └ Brand: Becker - Working range X [mm]: 2465 - Working range Y [mm]: 1260 - Z-axis working range [mm]: 324 - Transport dimensions: 4500mm x 2200mm x 2400mm (l x w x h) - Transport weight [kg]: 2500kg - Transport packages [pcs.]: 1 Financial information VAT: The price shown is exclusive of VAT VAT/margin: VAT deductible for entrepreneurs Delivery and trade-in always possible for everything in the industrial sectors Glenn Smeets

Condition: used, Year of construction: 2014, total height: 2,800 mm, total length: 10,300 mm, total width: 2,450 mm, Colour: Grey Empty weight: 6.600 kg Price: On request - Year: 2014 - Documentation available: No - CE marking present: Yes - CE certificate present: No - Serial number: AA2/002546 - Number of milling spindles [pcs.]: 1 - └ Milling spindle 1: - - Number of controlled axes [pcs.]: 5 - - Max. spindle speed [rpm]: 24000 - - Main motor power [kW]: 11 - Type milling table: Beam table - Tool clamping system: HSK-F63 - Material clamp system: Pneumatic - Drilling unit present: Yes - └ Motor power [kW]: 3 - └ Horizontal drill spindles [pcs.]: 6 - └ Vertical drilling spindles [pcs.]: 10 - Tool changer positions [pcs.]: 24 - System/software: Xilog plus - Safety feature: Safety light curtain, Door interlock switches, Enclosed fence - Vacuum pump present: Yes - └ Number [pcs.]: 1 - └ Brand: Becker - └ Type: Vtlf 250 - └ Year of manufacture: 2008 - └ Main motor power [kW]: 5.5 - └ Connection diameter [mm]: 70 - └ Oil free: Yes - Tools included: Yes - CNC options: Offcut conveyor, Manual control - CNC documentation available: USB stick - Table length [mm]: 5200 Lsdpfoytcl Ijx Al Ishh - Table width [mm]: 1300 - Voltage [V]: 400 - Current consumption [A]: 64 - Transport dimensions: 10300mm x 2450mm x 2800mm (l x w x h) - Transport weight [kg]: 6600kg - Transport packages [pcs.]: 1 Financial information VAT: The price shown is exclusive of VAT VAT/margin: VAT deductible for entrepreneurs Delivery and trade-in always possible for everything in the industrial sectors Glenn Smeets

Condition: used, Year of construction: 2014, operating hours: 11,517 h, Colour: Grey Empty weight: 6.000 kg - Year: 2014 - Documentation available: No - CE certificate present: No - Serial number: 070614/B/1-407 - Operating hours: 11517 - Number of milling spindles [pcs.]: 1 - └ Milling spindle 1: - - Number of controlled axes [pcs.]: 4 - - C-axis present: Yes Ledpsx E Uk Ujfx Al Ijhh - Type milling table: Flat table - Drilling unit present: Yes - └ Horizontal drill spindles [pcs.]: 6 - └ Vertical drilling spindles [pcs.]: 18 - Tool changer positions [pcs.]: 12 - Vacuum pump present: Yes - └ Number [pcs.]: 2 - └ Brand: Becker - └ Year of manufacture: 2023 - └ Main motor power [kW]: 18.5 - └ Capacity [m³/h]: 600 - └ Vacuum pressure [bar]: 250 - Working range X [mm]: 7220 - Working range Y [mm]: 1580 - Z-axis working range [mm]: 180 - Transport weight [kg]: 6000kg Financial information VAT: The price shown is exclusive of VAT VAT/margin: VAT deductible for entrepreneurs Delivery and trade-in always possible for everything in the industrial sectors Glenn Smeets

Condition: used, Year of construction: 2018, operating hours: 10,347 h, total height: 2,400 mm, total length: 7,000 mm, total width: 2,400 mm, Colour: Grey Empty weight: 3.450 kg - Year: 2018 - Documentation available: Yes Lsdpfoxtbgpex Al Ishh - CE marking present: Yes - CE certificate present: Yes - Operating hours: 10347 - Number of milling spindles [pcs.]: 1 - └ Milling spindle 1: - - Number of controlled axes [pcs.]: 5 - Type milling table: Beam table - Drilling unit present: Yes - └ Horizontal drill spindles [pcs.]: 10 - └ Vertical drilling spindles [pcs.]: 24 - Saw unit present: Yes - Tool changer positions [pcs.]: 25 - Vacuum pump present: Yes - └ Number [pcs.]: 1 - └ Brand: Becker - Working range X [mm]: 3110 - Working range Y [mm]: 1320 - Z-axis working range [mm]: 180 - Transport dimensions: 7000mm x 2400mm x 2400mm (l x w x h) - Transport weight [kg]: 3450kg - Transport packages [pcs.]: 1 Financial information VAT: The price shown is exclusive of VAT VAT/margin: VAT deductible for entrepreneurs Delivery and trade-in always possible for everything in the industrial sectors Glenn Smeets

Condition: used, Year of construction: 2012, total height: 2,400 mm, total length: 13,500 mm, total width: 2,450 mm, Colour: Grey Empty weight: 2.500 kg Biesse Rover A1536 G FR Year 2012 Central lubrifaction FT work table, X 3765 Y 1560, 9 zones 12 kW electro spindle, ISO 30, air cooled Biesse WORKS Biesse NEST MODULE Air conditioner 16 pos. revolver magazine Work area XYZ 3765*1585*170 2x vacu pump 250 m³ C axis 360° BH 17 L drilling group Including loading and unloading system - Year: 2012 - Documentation available: Yes - CE marking present: Yes - CE certificate present: No - Serial number: 81399 - Number of milling spindles [pcs.]: 1 - └ Milling spindle 1: - - Number of controlled axes [pcs.]: 3 - Type milling table: Flat table - Tool clamping system: ISO30 - Material clamp system: Pneumatic - Drilling unit present: Yes - └ Horizontal drill spindles [pcs.]: 4 - └ Vertical drilling spindles [pcs.]: 7 - Saw unit present: Yes - Tool changer positions [pcs.]: 16 - System/software: BiesseWorks - Safety feature: Safety mat - Vacuum pump present: Yes - └ Number [pcs.]: 2 - └ Brand: Becker - └ Capacity [m³/h]: 250 - CNC options: Unloading system, Loading system - Table length [mm]: 3765 - Table width [mm]: 1560 - Working range X [mm]: 3765 - Working range Y [mm]: 1585 - Z-axis working range [mm]: 170 - Transport dimensions: 13500mm x 2450mm x 2400mm (l x w x h) - Transport weight [kg]: 2500kg Lodpfxjwnip Ds Al Iohh - Transport packages [pcs.]: 4 Financial information VAT: The price shown is exclusive of VAT VAT/margin: VAT deductible for entrepreneurs Delivery and trade-in always possible for everything in the industrial sectors Glenn Smeets

Condition: used, Year of construction: 2012, operating hours: 9,974 h, total height: 2,700 mm, total length: 7,700 mm, total width: 2,420 mm, Empty weight: 7.390 kg CNC machining centre SCM Morbidelli M-600 5-axis machine Year of construction 2012 Machine no. AA2/002032 Working distance X-axis 5020 mm Working distance Y-axis 1680 mm Working distance Z-axis 250 mm Tool positions 36 Vertical drilling spindles 24  Software SCM XILOG MAESTRO SCM PRISMA K SCM TTS system Milling spindle liquid-cooled SCM TecPad MORBIDELLI TV Matic SCM PRO-SPACE SCM RAPID 12 SCM RAPID 24 Including vacuum pump Capacity 250 m3/h Disassembled for transport Weight 7450kg - Details: - └ Description: Machine gives malfunction spindle - Year: 2012 - Documentation available: No - CE marking present: Yes - CE certificate present: No - Serial number: AA2/002032 - Operating hours: 9974 - Number of milling spindles [pcs.]: 1 - └ Milling spindle 1: - - Number of controlled axes [pcs.]: 5 - Type milling table: Beam table - Drilling unit present: Yes - └ Horizontal drill spindles [pcs.]: 6 - └ Vertical drilling spindles [pcs.]: 24 - Saw unit present: Yes - Tool changer positions [pcs.]: 36 Ledpfownhccox Al Iehh - System/software: SCM Maestro - Vacuum pump present: Yes - └ Number [pcs.]: 1 - └ Brand: Becker - └ Capacity [m³/h]: 250 - CNC options: Offcut conveyor - Working range X [mm]: 5020 - Working range Y [mm]: 1680 - Z-axis working range [mm]: 250 - Transport dimensions: 7700mm x 2420mm x 2700mm (l x w x h) - Transport weight [kg]: 7390kg - Transport packages [pcs.]: 1 Financial information VAT: The price shown is exclusive of VAT VAT/margin: VAT deductible for entrepreneurs Delivery and trade-in always possible for everything in the industrial sectors Glenn Smeets

Condition: used, Year of construction: 2014, Colour: Grey Empty weight: 4.000 kg Price: On request - Machine available from: 2026-01-26 - Year: 2014 - Documentation available: No - CE marking present: Yes - CE certificate present: No - Serial number: 89867 - Number of milling spindles [pcs.]: 1 - Type milling table: Flat table - Tool clamping system: HSK-F63 Ljdpfoxr Evlox Al Iohh - Drilling unit present: Yes - Saw unit present: Yes - Tool changer positions [pcs.]: 12 - System/software: BiesseWorks - Safety feature: Safety mat - CNC options: Label machine, Loading system, Unloading system - Table length [mm]: 3600 - Table width [mm]: 1800 - Working range X [mm]: 3765 - Working range Y [mm]: 1875 - Z-axis working range [mm]: 324 - Transport weight [kg]: 4000kg - Transport packages [pcs.]: 1 Financial information VAT: The price shown is exclusive of VAT VAT/margin: VAT deductible for entrepreneurs Delivery and trade-in always possible for everything in the industrial sectors Glenn Smeets

Condition: excellent (used), functionality: fully functional, Fixed tool holders Machine: MORI SEIKI SL2000 Lhedpfeynb E Nex Al Ioh Turret manufacturer: SAUTER ---- 2x→ No. 444-119 Turning Tool Holder 25 mm steel holder Fixed turning tool holder Price: on request ----- 1x→ No. 444-201 Double Turning Tool Holder for main spindle and sub spindle with 1x clamping bar for 25 mm tool steels Fixed turning tool holder Price: on request ----- 1x→ No. 444-210 Boring Bar Holder Cylindrical mount ø 32 mm second mount ø 32 mm; 57 mm to the rear Price: on request ----- 1x→ No. 444-205 Turning Holder Mount 25 mm steel holder Price: on request

Condition: ready for operation (used), Year of construction: 2011, functionality: fully functional, CNC Spiral Bevel Gear Cutting Machine Gleason No 631 Year of manufacture: 2011 Control: SIEMENS 840d Retrofitted in 2011/2012 with new control, drives, etc. Ljdpfxjw Tfb So Al Iohh The machine was fully overhauled in 2011. A new control system and drives were installed.