Scrap shear

Lefort Typ C 420 TD

Condition: used, Year of construction: 2007, operating hours: 27,000 h, functionality: fully functional, A used mobile scrap shear is being offered for sale. The machine can be inspected at any time. Redpfoykzv Hox Afnst

Condition: excellent (used), Year of construction: 2014, operating hours: 37,656 h, functionality: fully functional, pressing force: 85 t, filling opening width: 1,500 mm, filling opening length: 1,100 mm, bale width: 1,100 mm, bale height: 750 mm, bale weight: 650 kg, overall weight: 25,000 kg, oil tank capacity: 1,000 l, year of last overhaul: 2024, volume flow: 410 m³/h, transport width: 2,400 mm, transport length: 9,300 mm, Hello, We are offering you a used baler from the manufacturer Presona AB, type LP 85 VH1, subject to availability. The following technical data was taken from the manufacturer's operating instructions and brochures, for which we cannot guarantee their accuracy or completeness. Manufacturer: Presona AB, Sweden Type: LP 85 VH1 Year of manufacture: 2014 Total operating hours: 37,565 hours, as of March 2025 Main press force: 85 t Specific press force: 100 N/cm² Pre-press flap force: 28 t Feed chute dimensions: 1,500 x 1,100 mm Filling volume per press cycle: 2.7 m³ Throughput under operating conditions: 410 m³/hour Bale dimensions: 1,100 x 750 mm Rodpev T I Evjfx Afnst Drive power: 55 kW Tying system: 5-fold vertical Hydraulic oil tank volume: 1,000 L Press dimensions: 10,350 x 2,400 x 3,150 mm (L x W x H) Press weight: approx. 25 t Note: The machine was used for compaction at a recycling plant. Used for the production of paper, cardboard, films, and plastics such as bottles, buckets, canisters, and drums. The press is in good condition. Many wear parts and entire assemblies have been replaced over the past three years. The machine has been regularly serviced. We would be pleased if this press is of interest to you. Your service team at Mertens & Frowein GmbH

Condition: reconditioned (used), Year of construction: 2002, operating hours: 44,590 h, functionality: fully functional, pressing force: 200 t, filling opening width: 1,020 mm, filling opening length: 2,000 mm, bale width: 1,100 mm, bale height: 1,100 mm, oil tank capacity: 3,100 l, power: 150 kW (203.94 HP), year of last overhaul: 2025, Technical data baler: Manufacturer MACPRESSE EUROPA S.R.L. Typ 112 Year of construction 2002, partially refurbished in December 2025 Operating hours 44,590 hours, stand December 2025 Press power main press 200 tons Specific press capacity 16,5 kg/cm² Feed channel 2,000 x 1,020 mm Filling volume 2,65 cm³ Theoretic throughput rate 795 m³/h Bale size 1,100 x 1,100 mm, length variable Driving motor 2 x 75 kW Tying system 5-fold horizontal, full automatic Throughput rate at MSW approx. 48 up to 54 tons/h, depends on material Volume hydraulic oil tank 3,100 l Machine weight baler approx. 50,8 tons Scope of delifery: 1 piece baler MACPRESSE, type 111A 1 operating manual with CE declaration, electrical and hydraulic circuit diagram Comments: The machine was serviced and partially overhauled in our workshop. The following work was carried out and parts replaced: • Hydraulic oil tank emptied and cleaned • Oil and air filters replaced • New hydraulic oil filled • All hydraulic hoses replaced • Press ram dismantled, broken down into individual parts, mechanics made operational • Front two main rollers replaced • Knives on the press ram replaced • Main hydraulic cylinder dismantled, disassembled, cylinder tube and piston rod checked, complete seal set replaced • Counter knife in the frame replaced • Knife gap adjusted to approx. 3 mm Rjdpfxjx Dnb Ue Afnst • Upper steel guide rails in the frame on the left and right replaced. • Worn press base cut out, base plate replaced with wear-resistant HARDOX steel. • Binding and twisting unit dismantled, broken down into individual parts, mechanics made functional, all twisting shafts and ball bearings replaced. • All wire rollers in the needle heads replaced • Wire knives cleaned and readjusted, chains greased and tensioned • All wire deflection rollers made operational • All door contact switches replaced • Wirbulator device dismantled, disassembled and made operational • General maintenance work carried out Finally, the press was subjected to a machine test in manual and automatic mode, see our video for the machine function test. The documentation (BA, CE, electrical/hydraulic circuit diagram) is complete. Viewing is possible by appointment. We accept no liability for the technical specifications or any errors.

Condition: used, Taps for pipe thread Before and finished Schneider R 2 3/4 inch Redpfx Afodk Rdvonet

Condition: good (used), Year of construction: 2002, functionality: fully functional, 3-axis machining center, CNC FANUC 18MC Complete with: - High-pressure through-spindle coolant - Belt chip conveyor - Spindle chiller - Manuals - CE certificate TRAVEL X axis (longitudinal table movement): 1020 mm Rsdpfxexfguvj Afnet Y axis (transversal table movement): 600 mm Z axis (vertical head movement): 560 mm TABLE Table-to-spindle distance: 150 / 710 mm Dimensions: 635 × 1200 mm Maximum table load: 1000 kg SPINDLE Table with T-slots: 6 x 18 mm h8 T Maximum speed: 10,000 rpm Gear ranges: 1 Maximum torque: 192 Nm Taper: No. 40 Internal bearing diameter: 70 mm FEED Rapid traverse: 32,000 mm/min Working feed: 1–20,000 mm/min Jog feed: 4,000 mm/min Thrust (x & y / z): 7,400 / 13,500 N ATC (Automatic Tool Changer) Tool holder taper type: ISO 40 [BT-40] Number of tools: 24 [32] Maximum tool diameter: 88 / 125 mm Maximum tool length: 300 mm Maximum tool weight: 7 kg Selection method: random Tool change time: 2.5 sec Chip-to-chip time: 6 sec MOTORS Spindle drive: 15 / 11 kW Servo motors (x & y / z): 2.1 / 3.8 kW Coolant pump: 0.5 kW (nozzles) Washing pump: +1.4 kW POWER SUPPLY Capacity: 30 kVA TANKS Lubricant: 4 liters Coolant: 400 liters DIMENSIONS Height: 2,825 mm Floor space: 2,650 × 2,200 mm Weight: 7,500 kg PLEASE NOTE: Machine only; vices and tools are not included in the sale.

Condition: used, Year of construction: 2012, operating hours: 11,850 h, pressing force: 88 t, filling opening length: 1,800 mm, bale length: 1,200 mm, bale width: 1,100 mm, bale height: 750 mm, overall weight: 23,000 kg, oil tank capacity: 2,000 l, power: 90 kW (122.37 HP), For sale used baler + used conveyor brand: HSM VK 88 + Stadler KF1800 Baler is VK 88 R – FU, Frequency drives, 2 x 45 kw. * Unblocking cylinder option * Ball joint fixing main ram cylinder * Stadler conveyor 1600 mm internal Year 2012 11850 hours Rod main cylinder and seals kit new. To be replaced : 2 front chamber floor section : middle and front to the channel Greasing / changing: Few sides diabolos are used and running, some rusty, some in good condition. Baler is running good and bales tying is ok Ram wheels OK Ram side wheels OK Rod main cylinder : almost new Main cylinder seals kit : almost new Ram sides nylon strips : 80 – 90 % good. Finetune the geometry adding spacers ( customer has parts on stock) Knife/ counter knife : good, 70% Needles wheels : ok but change is preferred + the closing plates Main frequency drive 1 of 2 : in total 2 x 45 kW : one is out of order. I don’t know if it will be changed or not. Baler is running on one pump. Side walls chamber : Side walls are worn out where the nylon guiding plate are sliding : few millimeters up to 2 mm average. Conveyor : Chain rollers are used with a bit of play. Greasing is missing but still good condition. Guiding strips are ok Feeding cleats are worn out, almost all. Rsdpfxeyuyg Se Afnet Start/stop with frequency drive. Side walls ok on incline part and in pit. Wire coils platform : Not included.

Condition: reconditioned (used), Year of construction: 2005, functionality: fully functional, pressing force: 90 t, filling opening width: 1,620 mm, filling opening length: 972 mm, bale width: 720 mm, bale height: 1,100 mm, bale weight: 600 kg, overall weight: 32,000 kg, pressure: 300 bar, power: 110 kW (149.56 HP), BOA baler with double pre-press flaps available in fully refurbished condition. The machine is located at our workshop in Almelo and can be inspected by appointment. If required, a matching (new) conveyor belt can be produced. The machine is perfectly suited for baling various materials such as cardboard, paper, plastics, car tires, and RDF. Rjdpfx Aexbc U Dofnst The machine is equipped with a so-called refu-ram. This is ideal for baling materials such as plastic bottles and/or shredded RDF. Technical specifications: Drive: 2x 55 kW Pressing force: 90 tons Bale dimensions: 1100 x 720 mm Bale weight: approx. 600 kg (depending on material) Number of tying wires: 5 vertical

Condition: good (used), Year of construction: 2008, operating hours: 24,629 h, functionality: fully functional, pressing force: 100 t, filling opening width: 1,100 mm, filling opening length: 1,650 mm, bale length: 1,200 mm, bale width: 1,100 mm, bale height: 1,100 mm, bale weight: 900 kg, overall weight: 24,000 kg, transport height: 3,000 mm, oil tank capacity: 2,000 l, power: 90 kW (122.37 HP), volume flow: 1,350 m³/h, transport width: 2,400 mm, transport length: 10,000 mm, Good day, We hereby offer you, without obligation, a used baling press from the manufacturer Presona AB, model LP 100 CH2 S. The following technical data has been taken from the manufacturer’s operating manual and brochures. We cannot guarantee the accuracy or completeness of this information. Manufacturer: Presona AB, Sweden Model: LP 100 CH2 S Year of manufacture: 2008 Total operating hours: 24,629 hours (as of February 2026) Effective pump operating hours: 10,090 hours Main press force: 100 t Specific compaction force: 81 N/cm² Pre-press flap force: 50 t Fill chute dimensions: 1,650 x 1,100 mm Fill volume per press cycle: 3 m³ Bale dimensions: 1,100 x 1,100 mm Drive power: 2 x 45 kW Tying: 5-fold vertical Hydraulic oil tank capacity: 2,000 L Transport weight (press only after disassembly): approx. 25 t Note: The machine was used in a recycling facility for compacting paper, cardboard, and films/foils. The press is in good condition and will be replaced by a new, larger machine in July 2026. Until then, it can be viewed in operation with materials processed. We would be pleased if this press is of interest to you. Your Service Team Mertens & Frowein GmbH Redpfxeymmmps Afnst

Condition: good (used), Year of construction: 1995, functionality: fully functional, pressing force: 70 t, filling opening width: 1,060 mm, filling opening length: 1,500 mm, bale width: 1,100 mm, bale height: 720 mm, bale weight: 500 kg, input voltage: 400 V, overall weight: 23,000 kg, noise level: 85 dB, power: 37 kW (50.31 HP), Used BOA 2060 for sale. The machine is currently stored in Belgium. It has been operational up until now and is currently disconnected. The machine is sold as-is, but a possible overhaul can be offered upon request. Technical data: Rodpsya Uwpefx Afnet Drive: 37 kW Pressing force: 70 tons Bale dimensions: 1100 x 720 mm Number of wires: 4 vertical, 2 horizontal Filling hopper dimensions: 1500 x 1060 mm Bale weight: approximately 500 kg (depending on material) Capacity: up to 14 tons per hour (depending on material) Press weight: 23,000 kg

Condition: new, We would like to offer shafts dedicated for HAAS 2000XL, 1500, and TEREX TDS 820 machines, equipped with side combs and a breaking bar. Rodpfxsx Hhuij Afnst -4-7-7 -4-9-9 PROTECHNIKA is a company with 21 years of history and from the very outset has specialized in the production of spare parts and complete recycling lines. In recent years, we have expanded our product portfolio to include the manufacturing of grinding shafts for slow-speed shredders. Through the implementation of automated welding processes and proprietary production technologies, we have significantly reduced lead times while maintaining consistently high quality. Grinding shafts are a series product, which, among other things, enables us to collaborate with machine manufacturers as an OEM supplier. What distinguishes PROTECHNIKA from the competition? It's simple! - Certified 3.1 materials - TUV SUD Rheinland-certified quality - ISO 9001 - Automated welding process / ISO 15613 / ISO 15614 compliant - Welders certified to ISO 9606-1 - ISO 9001:2015 - ISO 14001 - In-house design department capable of meeting any customer requirements - Our own RESEARCH AND DEVELOPMENT CENTER Customer relations are of paramount importance to us, as their satisfaction is our success!