Injection molding machine

FERROMATIK MILACRON K-TEC 250 S

Condition: like new (used), Year of construction: 2016, Wittmann Battenfeld Eco Power 110/130 Unilog B6P electric (2016) Clamping force: 110 t Screw diameter: 22 mm Dedpfxju Eki Se Aa Hscl Shot volume: 41 cm3 Screw L/D ratio: 20 Calculated stroke volume : 41,8 cm3 Correct injection pressure : 2,864 bar Max. screw speed : 500 min Screw tongue : 150 Nm Nozzle path contact force : 250/40 mm/kN Injection flow outside : 76 cm3/s Cylinder heating capacity : 6,3 kW Number of heating zones : 4 Working hours: 35.953 hours Type: Horizontal Drive: Electric

Condition: like new (used), Year of construction: 2008, operating hours: 6,200 h, functionality: fully functional, clamping force: 4,200 kN, screw diameter: 75 mm, Krauss-Maffei KM 420-2000 CX Krauss-Maffei injection molding machine, 420 tons of clamping force. Only 6,000 hours of automatic operation. Year of manufacture 2008. MC5 control. Screw diameter 75 mm. Extras: 8 hot runner zones. 2 cores on fixed platen, 2 cores on moving platen. 1 pneumatic valve on moving platen. The injection molding machine is delivered reconditioned by UK Transitus' expert technical team. We can offer commissioning at our clients' facilities, ensuring operation upon completion of the installation. Dedpowq D Efjfx Aa Hscl Technical Details 75mm screw Injection pressure: 1635 bar Shot volume: 1237 cm3 Shot weight: 1126 g Maximum distance between plates: 1400 mm Minimum mold thickness: 380 mm Opening stroke: 1020 mm Distance between columns: 900 x 800 mm Plate dimensions: 1270 x 1230 mm 75mm screw Clamping force: 4200 kN Year of manufacture: 2008 Working hours: 6282

Condition: ready for operation (used), Year of construction: 1997, Stock-No. 13602 Manufacturer Krauss Maffei Type of machine KM 650 – 8000 CM Year 1997 Working hours 80000 h Controlversion MC 3-F Screentext German Location Eschweiler - Germany Clamping unit: Clamping force 6500 kN Mould opening force, max. 346 kN Travel force movable platen opening 169 kN Travel force movable platen closing 144 kN Size of mould platens (h x v) 1704 x 1700 mm Distance between tie bars (h x v) 930 x 930 mm Mould opening stroke 1150 mm Mould height min 600 mm Max. daylight 1750 mm Hydraulic ejector - stroke 250 mm Ejector force 226 kN Injection unit: Screw diameter 130 mm Ls/D ratio 20 Injection pressure 1296 bar Stroke volume 6172 ccm Shot weight (PS) 5617 gr. Injection rate 1540 ccm/s Screw speed 138 1/min Plasticising rate max. 238 g/s Nozzle pressure 246 kN Electric and Hydraulic Equipment: Nominal capacity of pump motor 132 kW Installed heating capacity 70 kW Adjustable barrel heating zones 7 Dimensions and weights: Dimensions of the machine ca. 12,00 x 2,80 x 2,70 m Total machine weight 43000 kg Accessories: - Anti vibration pads Additional Options: - 1 x air valve - 2 x core pulls on movable plate - 2 x core pulls on fix plate - 8 x hotrunner controller - Robot interface according to Euromap 67 Djdpfoub S R Hjx Aa Hocl

Condition: good (used), Year of construction: 1997, functionality: fully functional, machine/vehicle number: 862-1053, Plastic Injection Moulding Machine | Mannesmann DEMAG - Ergotech 5000-2300 Clamping force [kN]: 5,000 Number of components: 1 Clamping platen width [mm]: 1,300 Clamping platen height [mm]: 1,200 Clear tie bar spacing, horizontal [mm]: 900 Clear tie bar spacing, vertical [mm]: 800 Centering ring diameter [mm]: 200 Minimum mould installation height [mm]: 400 Djdpfx Aeygikwea Hjcl Maximum mould installation height [mm]: 880 Maximum opening stroke [mm]: 810 Maximum ejector stroke [mm]: 230 Thread [M]: 24 Maximum mould weight [kg]: 6,700 Maximum mould weight, moving side [kg]: 4,400 Screw diameter [mm]: EE1: 60 Maximum shot weight [g] PS: EE1: 800 Injection unit configuration: EE1: horizontal Equipment: 2-core pull, with robot An inspection is possible at any time by appointment. Loaded free on truck (Butzbach). #Tags: Mannesmann-DEMAG | Ergotec | Ergotech5000

Condition: ready for operation (used), Year of construction: 2013, operating hours: 65,000 h, clamping force: 5,000 kN, screw diameter: 90 mm, total height: 2,355 mm, overall weight: 14,000 kg, product length (max.): 7,800 mm, This Engel DUO 4550/500 pico was manufactured in 2013. It features a clamping force of 5,000 kN, a screw diameter of 90 mm, and a maximum injection volume of 2,480 cm³. The machine dimensions are 7,800 x 2,405 x 2,355 mm, and it weighs 14,000 kg. Currently in production with approximately 65,000 operating hours, it remains in excellent condition. Contact us for more information about this machine. • Maximum injection volume: 2,480 cm³ • Minimum mold height: 350 mm • Maximum mold height: 900 mm • Platen opening stroke: 1,300 mm • Platen dimensions (W x L): 1,270 x 1,260 mm • Tie-bar distance (H x V): 910 x 830 mm • Motor power: 83 kW • Heater power: 61.2 kW • Number of electrical connection pins: 32 • Injection nozzle radius (tip): R35 • Centering ring diameter: 200 mm • Robot interface: Euromap 67 • Number of cores: 0 • Number of heating zones: 0 • Operating hours: approx. 65,000 h Dsdpfjx Nr Uxjx Aa Hecl • Condition: Excellent • Status: In production Additional equipment • Robot (equipped)

Condition: excellent (used), Year of construction: 2021, operating hours: 14,600 h, functionality: fully functional, machine/vehicle number: 248760, clamping force: 40,000 kN, screw diameter: 70 mm, displacement volume: 1,212 cm³, injection pressure: 1,650 bar, injection weight: 1,030 g, mold height (min.): 450 mm, ejector force: 964,000 N, ejector stroke: 250 mm, opening stroke: 1,000 mm, plate length: 1,450 mm, plate width: 1,200 mm, plate height: 1,100 mm, installation height: 3,650 mm, total length: 7,740 mm, total width: 2,340 mm, total height: 2,300 mm, overall weight: 25,600 kg, heating capacity: 29 kW (39.43 HP), pressure: 200 bar, number of injections: 1, pump power: 56,000 W, power: 118 kW (160.44 HP), type of input current: three-phase, input frequency: 50 Hz, input voltage: 400 V, input current: 213 A, Equipment: documentation/manual, The machine has few operating hours and is in very good condition, having been well-maintained. The machine comes with a Viper12 robot, which was originally supplied with it and can be seen in the accompanying photos. The robot’s control system is not integrated with the machine, so the robot can be removed and used separately, or another robot can be installed in its place. The machine has three air valves and two hydraulic valves, Euro map signals, and a signal for the dispensing unit’s rotation speed. The machine also has a strip guard, which is not included but can be arranged separately. The extruder’s heating elements are insulated with thermal insulation. Due to the guard, the machine can operate with the rear door open. It also has a water tank with 8 zones and two additional blocks with 8 outlets each. The machine has 8 zones for heating the tooling. Only PS material has been injection molded on this machine. Dcjdozqbk Njpfx Aa Hjl

Condition: ready for operation (used), Year of construction: 2007, operating hours: 101,500 h, clamping force: 3,000 kN, overall weight: 19,700 kg, Hydraulic injection moulding machine manufactured in 2007. This Engel Victory VC1800/300 P features a clamping force of 3,000 kN and an opening stroke of 900 mm. It includes a robust control system with a 15" TFT touchscreen and a maximum injection pressure of 1,735 bar. If you are looking to get high-quality injection moulding capabilities, consider the Engel Victory VC1800/300 P machine we have for sale. Contact us for further details. Identical Engel Victory VC 1800/300P (2008 model) also for sale — same configurations. Dedpjyn Ntzjfx Aa Hecl • Power supply: 3 x 400 V + N + PE / 50 Hz • Control system: ENGEL CC200 A02 (15" TFT touchscreen) • Opening stroke: 900 mm • Maximum platen distance: 1,500 mm • Minimum mould installation height: 600 mm • Ejector stroke: 200 mm • Ejector force: 90 kN • Pump drive power: 37 kW • Injection unit version: M3 • Available screw diameters: 60 / 70 / 80 mm • Screw diameter installed: 70 mm • Maximum swept volume (70 mm): 1,039 cm³ • Maximum screw speed: 226 rpm • Injection rate (70 mm): 385 cm³/s • Specific injection pressure (70 mm): 1,442 bar • Maximum injection pressure (increased): 1,735 bar • Nozzle stroke: 500 mm • Nozzle contact force: 110 kN • Hours: 101,500 h • Maintenance/Service history: • Complete hydraulic hose replacement in 2025 • Motor and planetary gearbox replacement in 2021 • High-pressure cylinder replacement in 2020 • Several cost-intensive main components renewed in recent years Additional equipment • Robot: ENGEL ERC 64 (included) • Axes travel: X 1,200 mm, Y 1,300 mm, Z 3,600 mm • B-axis rotation: -90° to +270° • Vacuum circuits: 4 • Pneumatic circuits: 8 • Reject/quality conveyor belt • Box transfer for 600 x 400 x 250 mm boxes • GWK temperature control tower (optional)

Condition: used, Year of construction: 2010, Injection moulding machine Krauss Maffei KM 650-4300, year 2010 Djdpow Hwthofx Aa Hjcl

Year of construction: 2014, condition: ready for operation (used), An ENGEL injection molding machine is offered. Clamping force: 1800kN, opening force: 96kN, max. opening stroke: 750mm, min. mold height: 300mm, max. platen distance: 1050mm, clear tie-bar spacing: tie-bar-less, mold mounting platens X/Y: 880mm/830mm, max. mold weight: 1500kg at center of gravity 230mm, ejector stroke: 180mm, ejector force forward/backward: 80kN/33kN, screw diameter: 55mm, metering stroke: 215mm, max. stroke volume: 510cm³, injection rate: 255cm³/s, max. injection pressure: 2050bar, nozzle stroke: 350mm, nozzle contact force: 67kN, injection unit heating capacity: 16.3kW, heating zones incl. nozzle: 5, barrel: M9 bimetallic barrel, integrated hot runner control zones: 24×220V, mold cooling circuits: 6×10l/min, hydraulic oil capacity: approx. 540l, operating hours: 67423h (as of 30.06.2026). The machine will be available from December. Machine dimensions X/Y/Z: approx. 6275mm/1888mm/2100mm, weight without mold: approx. 12200kg. Documentation available. An on-site inspection is possible. Dedpfxszt Slpj Aa Hjcl

Condition: excellent (used), Year of construction: 2007, clamping force: 2,000 kN, screw diameter: 55 mm, injection pressure: 2,183 bar, injection weight: 562 g, mold height (min.): 400 mm, ejector stroke: 180 mm, Engel VC 1350/200 Tech Clamping force: 200 tons Year of manufacture: 2007 Weight: 14,200 kg Dimensions (L x W x H): 6.3 x 1.9 x 2.3 m Injection unit: .../1350 Screw diameter: 55 mm Injection volume: 618 cm³ Shot weight (for PS): 562 g Djdpfx Ajzt I Sroa Hecl Specific injection pressure: 2,183 bar Mould clamping system: 200/... Mould platen dimensions: 860 x 570 mm Mould installation height: 400 mm Opening stroke: 750 mm Maximum platen distance: 1,150 mm Ejector stroke: 180 mm Ejector force: 80 kN Equipment: - 2 × hydraulic core on moving platen - Pneumatic valve - 8 hot runner zones - 8-section rotameter