Used oil storange tank

DEHOUST DOPPELWANDIG

Condition: used, Hydraulic Guillotine Shear STEINER Type HTS 30/20 R Ltedpfx Ajd Hxx Aja Eoa Machine No. 315 Year of manufacture: 1982 Cutting length: 3050 mm Cutting thickness: 20 mm Backgauge: 800 mm, motorized control Motor power: approx. 30 kW Power supply: 400 Volt, 50 Hz - Backgauge with ELGO position control - Backgauge adjustment via ball screw spindles - SICK safety light curtain at the front for access protection - 3 material support arms with ball rollers - Electric foot switch - Spare blade - Oil cooler with air heat exchanger - Extremely heavy-duty machine in very robust construction Base machine dimensions L x W x H: 4650 x 2610 x 3200 mm Base machine weight: 27,000 kg Transport space required (base machine) L x W x H: 4650 x 2610 x 3200 mm Transport space required (additional) L x W x H: 3500 x 2450 x 1400 mm Total weight: 27,000 kg Good condition Machine can be inspected at our warehouse in 37235 Hessisch Lichtenau. Test cuts possible.

Condition: used, Year of construction: 2023, operating hours: 100 h, power: 107 kW (145.48 HP), maximum speed: 40 km/h, front tire size: 540/65R24 BKT, rear tire size: 650/60R28 BKT, Equipment: all wheel drive, compressed air brake, Claas Arion 470 CIS+ approx. 30 operating hours Current equipment: Rear tires: BKT 650/60R 38 Front tires: BKT 540/65 R24 CLAAS front linkage 2.8 t incl. external control External operation at front linkage (CIS) 2 engine speed memories with starting gear and automatic shifting Alternator 200 A/h ISOBUS pre-installation, rear Unlocked Task Control Basic, tractor-side Multifunction lever with ELECTROPILOT Lsdsv R Niwjpfx Aa Eota Revershift function on multifunction lever Rear linkage, electrohydraulic, 6.25 t Lower links Cat. 3 with hook ends Top link Cat. 3/2 with hook ends Automatic tow hitch with 38 mm pin diameter Compressed air braking system (dual-circuit) Additional air connection, right cabin side Hydraulic system load-sensing (150 l/min) 3 valves, electrohydraulic proportional, CIS+ Mid-mounted valves assigned to front linkage and 1x double-acting/rear 2 front couplers HEXASHIFT transmission Gear ratio 40 km/h PROACTIV front axle with independent wheel suspension incl. steering angle sensor Rear axle, standard PTO 540/540 ECO + 1000 rpm PTO stub 6-spline, 1"3/8 With automatic PTO, rear SMART STOP with cruise control management 145 HP max. output, 154 HP homologated rated output, ECE R 120 Master battery switch, automatic, electronic 6-post PANORAMIC cab, 2-point cab suspension Mechanical mirrors, incl. wide-angle, telescopic Additional interface sockets 2 auxiliary headlights on roof, halogen Main headlights + 2 work lights on engine hood LED work lights: 2x front, 4x rear Comfort seat, fabric, low-frequency suspension, heated Passenger seat with safety belt MP3 radio with Bluetooth, USB and hands-free kit Cool box for 1.5 l bottle (under instructor seat) Automatic all-wheel drive, steering angle dependent | Internal No.: 11114182

Condition: new, Ostas 3-roll round bending machine ORM 1070 x 110 Technical specifications: Special equipment included in the price: hardened rollers motorized rear roller adjustment digital display sheet width 1070 mm sheet thickness 5,0 mm max. sheet thickness 4,0 mm bending roll length 1070 mm roll diameter 110 mm weight 1000 kg dimension L-W-H 2250 x 800 x 1100 mm Motor: 2.2 KW Equipment: Ltodpfsgkwhajx Aa Eea upper and lower roller electrically driven upper roller can be swung out conical bending device asymmetric roller arrangement self-braking main motor sep. control and operating panel safety line CE-sign

Condition: used, Year of construction: 2022, operating hours: 550 h, Lightly used and well-maintained Komatsu PC 20 R-5 mini excavator Technical data: * Operating weight incl. attachments approx. 2,000 kg * Komatsu 3D67E-2A engine with 11.8 kW * Overall length: 3,845 mm * Overall height: 2,370 mm * Overall width (minimum): 1,280 mm (990 mm) * Track width: 230 mm Ltjdpfxjrwvvys Aa Eea * Tail swing radius: 1,120 mm * Track length: 1,570 mm * Max. digging reach: 4,100 mm * Max. digging depth: 2,370 mm * Minimum swing radius: 1,515 mm Equipment included: * 2 travel speeds with auto shift-down * Servo control * Long dipper arm * 2-way auxiliary hydraulics to the boom (switchable for hammer operation) * Protective cover on the boom lift cylinder * Work light on the boom * Dozer blade * Travel alarm (acoustic) * Tool kit * CE conformity * Cab with heater * 1x standard hydraulic circuit (with pedal) * Suspension driver's seat with fixed 2-point safety belt * Rubber tracks * Mechanical quick coupler LEHNHOFF MS01 + load hook Other: * Attachments are NOT included - sale on request

Condition: like new (used), Year of construction: 2024, Cantilever rack double-sided used: Hot-dip galvanized screw system Scope of delivery: 4 double-sided shelf stands, height 4,160 mm with foot section 1,200 mm 24 cantilevers with 1,200 mm depth, standard Including longitudinal and diagonal braces for 1,300 mm axle spacing Incl. fastening material (without ground anchors) - (*Delivery time approx. 1 week) - (*No damaged parts!) - (*Reorder spare parts and extension possible at any time) - (*Also available in larger quantities: 20 stands in stock) Lsdpfx Aaoh Ek Dae Ejta Detailed description: - Stable steel construction made of IPE profiles - Surface of all components hot-dip galvanized - Load capacity per stand side 2,250 kg - Load capacity per cantilever arm 750 kg - Cantilever arms height adjustable in 100 mm increments - 6 screwable cantilever arms per stand and 2 base sections with a depth of 1,200 mm, standard = 4 storage levels one above the other per side of the stand - Including longitudinal and diagonal braces for 1,300 mm spacing - Shelf length 4,000 mm - Including fastening material (without ground anchors) - With assembly instructions and load plates C4 in accordance with DIN standard - Expert advice by telephone - Made in Germany - Short delivery time - Collection on site possible Our cantilever racks are produced exclusively in Germany. We offer reliable freight with registration before delivery. The material is sensibly packed to enable easy unloading. When installed outdoors, the load-bearing capacity is reduced by the wind and snow load. The subsurface must be made of concrete, level and dowel-capable and must be able to bear the loads. The condition of the soil and load-bearing capacity as well as any official permits required must be checked and guaranteed by the customer. The shelf supports must be anchored to the floor on site; anchoring to the wall is not necessary and not recommended. According to the trade association, it is recommended that the shelf supports on the top storage level have a projection of at least 500 mm above the top edge of the supports.

Condition: used, machine/vehicle number: 12216, Rotor diameter: 300 mm Rotor width: 500 mm Lsdpfoh D Imisx Aa Eota 3-knife rotor 2 rows stator knives Inlet cross section approx. 300 x 500 mm Drive motor: 30 kW

Condition: used, CNC Universal Coordinate Drilling and Milling Machine FEHLMANN type PICOMAX 100-CNC 3 CNC control HEIDENHAIN TNC 155 make no. 16186651 year of construction 1986 spindle holder FEHLMANN SF32 drilling capacity Ø 30 mm in steel threading up to M20 in steel travel X: 850 mm, Y: 435 mm pinol stroke Z: 210 mm vertical movement milling head 580 mm Feed X and Y 1 to 8000 mm/min. Feed Z 1 to 4000 mm/min. Rapid traverse X and Y 8 m/min. rapid traverse Z 4 m/min. Table clamping surface 1570 x 500 mm distance spindle nose - table 130 - 720 mm projection spindle - column 450 mm Spindle speed 50 - 7100 rpm. Stepless spindle drive 10 kW Total connected power 20 kW Mains connection 400 Volt, 50 Hz - CNC control HEIDENHAIN TNC 155 with TFT monitor - 3 axes controlled, X, Y and Z pinol adjustment - hydro-mechanical tool clamping FEHLMANN SF32 - thread cutting device - cable remote control for machine operation and axis movements - motorized vertical movement of the milling head with shut-off via adjustable cams - 3D probe RENISHAW, type MP 11F with holder Fehlmann SF32 - 20 tool holders FEHLMANN SF32 - swivelling tool holder with 21 tool places - Coolant device in the machine column - control cabinet fixed to the machine - Documentation Operating manual, control manual and E-circuit diagrams space requirement L x W x H 2350 x 2000 x 2300 mm Ltedehik Ezjpfx Aa Eea weight 3,2 ton. very good condition

Condition: new, pressure: 100bending length: 2500column width: 2100daylight: 365stroke lenght (max.): 180column throat depth: 300messurements (LxWxH): 3760 x 2150 x 2450weight approx.: 6500motor power: 5,5          Standard equipment: KK-Industries GmbHhas the general agency of the KK Kletzer group of companies. We have put together a high-quality model for Europe. The CNC press brake KK-Industries made by KK Kletzer bursa Turkey Model KK Kletzer Europa Compact The strong press brake KK Kletzer Europa Compact  is characterized by its high precision, accuracy and versatile application. KK Kletzer Europa Compact   press brake distinguishes itself by its high precision, accuracy and versatility. We focus on quality, which is also reflected in the control system. As standard control we have the high-quality controls from Italy 10 2 D with simplest programming Furthermore, the press brake KK Kletzer Europa Compact  is equipped with Y1, Y2, X CNC axes via the control. Even with the top tool and the die we make no compromises and equip the CNC press brake KK Kletzer Europa Compact   with quality tools from EUROSTAMP Italy. or Rolleri Italy. Of course, every machine is just as good as the service. That's why we put our focus on highly qualified employees with long experience in the CNC sheet metal working area. CNC axes Y1, Y2, X Control 2 D 10 Backgauge with double linear guidance and ball screw centrally adjustable crowning device 2 pcs Aulfagearme front heavy version Height adjustment on linear guide Laser protection device on the upper beam CE protection options: CNC R-axis     EURO 4.300,- CNC crowning EURO 2.600,- Distributed by: Ltsdpsd Iy Tvofx Aa Eea KK-Industries GmbH Tel: 0043 (0)664 380 7776 There's something for everyone!

Condition: used, mileage: 295,000 km, power: 120 kW (163.15 HP), first registration: 03/2018, fuel type: diesel, overall weight: 3,500 kg, gearing type: mechanical, emission class: euro6, loading space length: 4,200 mm, Equipment: soot filter, - Air conditioning - 4200mm loading platform - excellent condition Suspension: leaf spring suspension Ltjdpfx Aaexcd Nlj Esa

Condition: good (used), functionality: fully functional, The Pieralisi Decanter is a high-capacity horizontal centrifuge designed for industrial applications that require efficient solid-liquid separation. The decanter is used to separate two or more specific phases of differing densities, especially for clarifying liquids containing suspended solids. The separation of solids and liquids takes place inside a cylindrical-conical rotating bowl, where the heavier solid phase collects on the periphery and is continuously removed by an internal screw conveyor. Its key technical specifications are detailed below: Technical specifications: - Bowl diameter: 353 mm Ljdpfswxw Atox Aa Eota - Maximum bowl speed: 4,100 rpm - Maximum centrifugal force: 3,300 x g - Bowl length/diameter ratio: 4.30 l/d Applications: Wastewater treatment: For the separation of suspended solids from liquids. Oil and fat industry: For the separation of components such as oil and water. Food industry: For juice extraction processes, edible oil or pulp separation. Chemical industry: For separating liquid suspensions of chemical products.